1
481 Panet Road Winnipeg, MB R2C 2Z1
15 AND 25 GALLON SPRAYERS
INSTRUCTION MANUAL
GENERAL INFORMATION
The purpose of this manual is to assist you in operating and maintaining your lawn and garden
sprayer. Please read it carefully as it furnishes information which will help you achieve years of
dependable trouble free operation.
WARRANTY-PARTS-SERVICE
To obtain prompt, efficient service, always remember to give the item number and your model
number. Whenever you need parts or repair service, contact Princess Auto Ltd. at:
Telephone # 1-800-665-8685 Fax # 1-800-265-4212
The sprayer is shipped in a carton and requires assembly before it can be used.
Refer to parts list and drawing, and then follow this procedure when assembling:
IA) ASSEMBLY INSTRUCTION FOR 25 GAL. PULL TYPE, ITEM # 8002029 (P. 17-19)
1) Install tow frame (19) on frame (17) using bolts (18) and lock nuts (13).
2) Install boom frame (10) on frame (17) using bolts (9) and lock nuts (13).
3) Install lid and outlet plug on tank (69) with tether straps.
4) Install tank (69) on frame (17) using bolts, lock washers, and plain washers (14), (15), (16).
5) Slide wheels (12) on to axle followed by washer (11) and install cotter pin (71).
6) Insert boom slide frame (55) into bottom boom frame (10) and lock in position using pin (67)
and thumb screw (66).
7) Install boom arm left inside (1), right inside (50) on frame boom slide (55) using carriage
bolt, plain washer, lock washer, and wing nut (54), (4), (56), (57).
8) Install boom arm left outside (5), right outside (43) on inside boom arms (1),(50) using bolt,
plain washer, lock washer, and nut (2), (4), (56), (3).
9) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings
10) Mount pump (27) and switch holder (28) to tank using screws (34).
NOTE: There is an extra 6 feet of red wire so that the switch can be mounted
near the operator. If mounted on the tank, wrap the extra 6 feet of wire.
9110602
REV. 05 NOV. 03
2
11) Install grommet (47) on tank (69).
12) Insert hose (48) through grommet (47). Lubricate grommet for ease of installation.
13) Slide hose clamp (46) on hose (48). Insert hose to elbow (26) on pump and tighten clamp.
From inside tank install barb (45) and strainer (44) to hose (48).
Note: Place hose in bottom of tank, so that it does not curl upward.
14) Slide hose clamp (38) on hose (64), insert hose on barb hose flat (35), slide hose clamp on
opposite end of hose, and connect the hose into tee (52) and tighten clamps.
Important: Ensure direction of the tee is as per drawing.
15) Install barb (25) and vinyl washer (62) to tank (69).
16) Slide hose clamp (38) on hose (33), connect hose to barb (25), slide hose clamp on opposite
end of hose. Connect hose on barb hose flat (35) and tighten clamps.
17) Install clips (32) to tank (69) using screws (60).
18) Slide hose clamp (38) on hose (58), connect hose to barb hose flat (35). Connect opposite
end to wand (59). Hose can be wrapped around tank and wand inserted in clips.
19) Install nut (6) on elbow (37) and tee (51), turn the nut up to the end of the thread on elbow
and tee.
20) Pass elbow (37) and tee (51) through hole on boom arms (43), (50), (1), (5).
21) Install O-ring (40) on filter (39). Insert filter (39) in elbow (37) and tee (51) and install
O-ring (40), nozzle tip (41) and nut (42) on elbow and tee.
22) Tighten nut (6) toward boom. Do not over tighten. Adjust the nozzle spray direction
directly towards the ground.
23) Repeat 19, 20, 21 and 22 for all nozzles.
24) Tie hoses (49), (8) using cable tie (68) on boom arm holes (1), (5), (43), (50).
25) Make sure all fittings are tight.
Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying.
YOUR SPRAYER IS READY TO USE.
NOTE: Read instruction manual and understand fully before operating the unit.
3
IB) ASSEMBLY INSTRUCTION FOR 25 GAL. PULL TYPE DELUXE,
ITEM # 8002065 (P.20-22)
1) Install tow frame (33) on frame (36) using bolt (35) and lock nut (37).
2) Install boom frame (27) on frame (36) using bolt (67) and lock nut (37).
3) Install tank (38) on frame (36) using bolt, lock washer, and plain washer (30), (31), (32).
4) Install lid and outlet plug on tank (38) with tether straps.
5) Slide tires (29) on to axle and install washer (28) and cotter pin (66).
6) Insert boom slide frame (14) on boom frame (27) and lock in position using pin (25) and
thumb screw (17).
7) Install middle boom (18) and spacers (15) on frame boom slide (14) with bolt (13) and lock
nut (37).
8) Install left boom (21) and right boom (4) on middle boom (18) with bolt (67) and lock nut
(37).
9) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings.
10) Mount pump (44) and switch holder (41) to tank using screws (45).
NOTE: There is an extra 6 feet of red wire so that the switch can be mounted
near the operator. If mounted on the tank, wrap the extra 6 feet of wire.
11) Install grommet (11) on tank (38).
12) Install barb (39) and vinyl washer (6) to tank (38).
13) Insert hose (57) through grommet (11). Lubricate grommet for ease of installation.
Note: Place hose in bottom of tank, so that it does not curl upward.
14) Slide hose clamp (9) on hose (57). Insert hose to elbow (42) on pump and tighten clamp.
From inside tank install barb (58) and strainer (59) to hose (57).
15) Install clips (63) to tank (38) using screws (64).
16) Slide hose clamp (49) on hose (26), insert hose on barb hose flat (48), and connect the other
end of hose into barb on wand (20) and tighten clamp. Hose can be wrapped around tank and
wand inserted in clips.
17) Slide hose clamp (49) on hose (50), insert hose on barb hose flat (48), slide hose clamp on
opposite end of hose, and connect hose to barb (39) and tighten clamps
18) Slide hose clamp (49) on hose (10), insert hose on barb hose flat (48), slide hose clamp on
opposite end of hose, and connect hose to cross (16) and tighten clamps. 4
19) Slide hose clamp (49) on hose (2), connect hose to elbow (1), slide hose clamp on opposite
end of hose. Connect hose to tee (19) and tighten clamps.
20) Slide hose clamp (49) on hose (8), connect hose to tee (19). Slide hose clamp on opposite
end of hose, connect hose to cross (16) and tighten clamps.
21) Repeat 19 and 20 for the opposite side.
22) Install nozzle bodies (1), (16), (19) to boom with clamps (22). The nozzle bodies should be
at 30” spacing. The inside hoses (8) are longer so that the outside booms can pivot.
23) Insert nozzle (51) into cap (23) followed by rubber gasket (52). Insert filter (53) in nozzle
bodies (1), (16), (19). Install cap (23) on nozzle bodies (1), (16), (19) by turning half a turn.
24) Rotate outside booms (4) and (21) so they are folded in. Install springs (7) on booms.Tighten
or loosen locknut (37) until the outside arms can rotate on their own with the spring installed.
NOTE: If locknut is too loose, movement of boom arm can be dangerous.
25) Make sure all fittings are tight.
Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying.
YOUR SPRAYER IS READY TO USE.
NOTE: Read instruction manual and understand fully before operating the unit.
IC) ASSEMBLY INSTRUCTION FOR 25 GAL. THREE POINT HITCH,
I
TEM # 8002047 (P. 23-25)
1) Install boom frame (48) on frame (40) using bolt (49) and lock nut (44).
2) Install lid and outlet plug on tank (39) with tether straps.
3) Install tank (39) on frame (40) using bolt, lock washer, and plain washer (45), (46), (47).
4) Insert boom slide frame (11) on boom frame (48) and lock in position using pin (50) and
thumb screw (7).
5) Install boom arm left inside (19), right inside (4) on frame boom slide (11) using carriage
bolt, plain washer, lock washer, and wing nut (14), (10), (9), (8).
6) Install boom arm left outside (28), right outside (1) on inside boom arms
(19), (4) using bolt, plain washer, lock washer, and nut (27),(10),(9),(2).
7) Install barb (33) and vinyl washer (21) to tank (39).
8) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings.
9) Mount pump (34) and switch holder (32) to tank using screws (26).
5
NOTE: There is an extra 6 feet of red wire so that the switch can be mounted
near the operator. If mounted on the tank, wrap the extra 6 feet of wire.
10) Install grommet (54) on tank (39).
11) Insert hose (53) through grommet (54). Lubricate grommet for ease of installation.
Note: Place hose in bottom of tank, so that it does not curl upward.
12) Slide hose clamp (63) on hose (53), insert hose to elbow (31) on pump and tighten clamp.
13) Slide hose clamp (5) on hose (13), insert hose on barb hose flat (17), slide hose clamp on
opposite end of hose, and connect hose into tee (12) and tighten clamps.
14) Slide hose clamp (5) on hose (18), connect hose to tee (12), slide hose clamp on opposite end
of hose. Connect hose into tee (6) and tighten clamps.
15) Slide hose clamp (5) on hose (55), connect hose to tee (6). Slide hose clamp (5) on opposite
end of hose, insert elbow (56) into hose and tighten clamp.
16) Repeat 15 and 16 for the opposite side.
17) Install nut (57) on elbow (56) and tee (6), turn the nut up to the end of the thread on elbow
and tee.
18) Pass elbow (56) and tee (6) through hole on boom arms (1),(6),(19),(28).
19) Install O-ring (58) on filter (59). Insert filter (59) in elbow (56) and tee (6) and install O-ring
(58), nozzle tip (60) and nut (61) on elbow and tee. Hand tighten nut (61).
20) Tighten nut (57) toward boom. Do not over tighten. Adjust the nozzle spray direction
directly towards the ground.
21) Repeats 18 – 21 for the other nozzles.
22) Tie hoses (55),(18) using cable tie (68) on boom arm holes (1),(4),(19),(28).
23) Install clips (38) to tank (39) using screws (37).
24) Slide hose clamp (5) on hose (3), insert hose on barb hose flat (17), and connect the other
end of hose into barb on wand (30) and tighten clamp. Hose can be wrapped around tank and
wand inserted in clips.
25) Slide hose clamp (5) on hose (25), insert hose on barb hose flat (17), slide hose clamp on
opposite end of hose, and connect hose to barb (33) and tighten clamps.
26) Make sure all fittings are tight.
Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying.
YOUR SPRAYER IS READY TO USE.
NOTE: Read instruction manual and understand fully before operating the unit.
6
ID) ASSEMBLY INSTRUCTION FOR 25 GAL. PULL TYPE BOOMINATOR,
ITEM # 8034888 (P. 26 & 27)
1) Install tow frame (37) on frame (35) using bolt (38) and lock nut (3).
2) Install boom frame (1) on frame (35) using bolt (2) and lock nut (3).
3) Install tank (34) on frame (35) using bolt, lock washer, and plain washer (41), (40), (39).
4) Install lid and outlet plug on tank (34) with tether straps.
5) Slide tires (43) on to axle followed by washer (42) and install cotter pin (44).
6) Insert nozzle holder (5) on boom frame (1) and lock in position using thumb screw (4).
7) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings.
8) Mount pump (18) and switch holder (24) to tank using screws (46).
NOTE: There is an extra 6 feet of red wire so that the switch can be mounted
near the operator. If mounted on the tank, wrap the extra 6 feet of wire.
9) Install grommet (26) on tank (34).
10) Install barb (28) and vinyl washer (12) to tank (34).
11) See bottom left hand view for hose assembly. Insert hose (21) through grommet (26).
Lubricate grommet for ease of installation.
Note: Place hose in bottom of tank, so that it does not curl upward.
12) Slide hose clamp (22) on hose (21). Insert hose to elbow (29) on pump and tighten clamp.
From inside tank install barb (47) and strainer (27) to hose (21).
13) Install clips (33) to tank (34) using screws (32).
14) Slide hose clamp (9) on hose (49), insert hose on barb hose flat (11), and connect the other
end of hose into barb on wand (16) and tighten clamp. Hose can be wrapped around tank and
wand inserted in clips.
15) Slide hose clamp (9) on hose (25), insert hose on barb hose flat (11), slide hose clamp on
opposite end of hose, and connect hose to barb (28) and tighten clamps
16) Slide hose clamp (9) on hose (50), insert hose on barb hose flat (11), slide hose clamp on
opposite end of hose, and connect hose to brass barb (15) and tighten clamps.
17) Insert brass barb (15) into hole on nozzle holder (5) and install check valve (5) (Make sure
arrows on check valve are pointing in the direction of flow.) to brass barb followed by
nozzle (7). Make sure teflon tape is used on threads. Tighten nozzle enough to prevent
leaking and make sure nozzle is pointing downwards. When sprayer is first tested with
water, rotate nozzle for even spray distribution. Do not overtighten. 7
18) Make sure all fittings are tight.
Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying.
YOUR SPRAYER IS READY TO USE.
NOTE: Read instruction manual and understand fully before operating the unit.
IE) ASSEMBLY INSTRUCTION FOR 15 GAL. SPOT, ITEM # 5740063 (P. 28 & 29)
1) Install lid and outlet plug on tank (12) with tether straps.
2) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings.
3) Mount pump (17) to tank using screws (18).
4) Install grommet (29) on tank (12).
5) Install barb (13) and vinyl washer (5) to tank (12).
6) Insert hose (20) through grommet (29). Lubricate grommet for ease of installation.
Note: Place hose in bottom of tank, so that it does not curl upward.
7) Slide hose clamp (15) on hose (20) insert the hose to elbow (14) on pump
and tighten clamp. From inside tank install barb (19) and strainer (21) to hose (20).
8) Slide hose clamp (23) on hose (16) insert the hose on barb hose flat (4). Slide hose clamp on
opposite end of hose and connect to barb (13).
9) Plug wire (30) to wire from pump.
10) Install clips (24) to tank (12) using screws (25).
11) Slide hose clamp (23) on hose (2), insert the hose on barb hose flat (4). Slide hose clamp on
opposite end of hose, and connect the hose into wand (1) and tighten clamp. Hose can be
wrapped around tank and wand inserted in clips.
12) Make sure all fittings are tight.
Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying.
YOUR SPRAYER IS READY TO USE.
NOTE: Read instruction manual and understand fully before operating the unit.
8
IF) ASSEMBLY INSTRUCTION FOR 15 GAL. ATV BOOMINATOR,
ITEM # 8034879 (P. 30 & 31)
1) Install lid and outlet plug on tank (8) with tether straps.
2) Install frames (4) to tank (8) using bolt, lock washer and plain washer (1),(2),(3).
3) Install right bracket (6) and left bracket (38) to frame (4) using bolt, plain washer, and lock
nut (5),(3),(36). The holes that you use on the brackets are dependant on your ATV.
4) Install boom support (39) to brackets (6) and (38) using bolt, 2 washers, and lock nut
(5),(3),(3),(36).
5) Insert nozzle holder (43) into boom support (39) and lock in position using thumb screw (41).
Install bolt (46) to nozzle holder with lock nut (42).
6) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings.
7) Mount pump (29) to tank using screws (28).
8) Install grommet (33) on tank (8).
9) Insert hose (34) through grommet (33). Lubricate grommet for ease of installation.
Note: Place hose in bottom of tank, so that it does not curl upward.
10) Slide hose clamp (16) on hose (34). Insert hose to elbow (30) on pump and tighten clamp.
From inside tank install barb (10) and strainer (7) to hose (34).
11) Install barb (15) and vinyl washer (24) to tank (8).
12) Slide hose clamp (26) on hose (13), insert hose on barb hose flat (23) and tighten clamps.
13) Install clips (11) to tank (8) using screws (12).
14) Slide hose clamp (26) on hose (40), insert hose on barb hose flat (23). Slide hose clamp on
opposite end of hose and connect the hose into barb on wand (14). Hose can be wrapped
around tank and wand inserted in clips.
15) Slide hose clamp (26) on hose (27), insert hose on barb hose flat (23), slide hose clamp on
opposite end of hose, and connect hose to barb (15) and tighten clamps.
16) Insert brass barb (47) into hole on nozzle holder (43) and install check valve (44) (Make
sure arrows on check valve are pointing in the direction of flow.) to brass barb followed
by nozzle (45). Make sure teflon tape is used on threads. Tighten nozzle enough to prevent
leaking and make sure nozzle is pointing downwards. When sprayer is first tested with
water, rotate nozzle for even spray distribution. Do not overtighten.
9
17) Make sure all fittings are tight.
Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying.
YOUR SPRAYER IS READY TO USE.
NOTE: Read instruction manual and understand fully before operating the unit.
IG) ASSEMBLY INSTRUCTION FOR 15 GAL. PULL TYPE, ITEM # 8002001 (P. 32-34)
1) Install tow frame (20) on frame (21) using bolt (19) and lock nut (46).
2) Install lid and outlet plug on tank (18) with tether straps.
3) Install tank (18) on frame (21) using bolt, lock washer, and washer plain (22), (23), (24).
4) Install boom frame (37) on frame (21) using bolt, lock washer, and weld nut (22), (23), (26).
5) Slide wheels (27) on to axle followed by washer (28) and install cotter pin (59).
6) Install boom pipe (36) to the required hole location using U bolt (38) and lock nut (57).
7) See page 16 for pump assembly diagram. Use Teflon tape on all pipe thread fittings.
8) Mount pump (11) and switch holder (13) to tank using screws (8).
NOTE: There is an extra 6 feet of red wire so that the switch can be mounted
ear the operator. If mounted on the tank, wrap the extra 6 feet of wire.
9) Install grommet (16) on tank (18).
10) Insert hose (15) through grommet (16). Lubricate grommet for ease of installation.
Note: Place hose in bottom of tank, so that it does not curl upward.
11) Slide hose clamp (42) on hose (15) insert hose to elbow (43) on pump and tighten clamp.
From inside tank install barb (44) and strainer (45) to hose (15).
12) Slide hose clamp (2) on hose (29), insert hose on barb hose flat (4), slide hose clamp on
opposite end of hose, and connect the hose into tee (39) and tighten clamps.
Important: Ensure direction of the Tee is as per drawing.
13) Install clips (51) to tank (18) using screws (52).
14) Slide hose clamp (2) on hose (55), insert hose on barb hose flat (4), slide hose clamp on
opposite end of hose, and connect the hose into barb on wand (56) and tighten clamps. Hose
can be wrapped around tank and wand inserted in clips.
15) Install barb (17) and vinyl washer (25) to tank (18).
16) Slide hose clamp (2) on hose (1), insert hose on barb hose flat (4) and tighten clamps.
17) Slide hose clamp (2) on hose (1), connect hose to tee (39),and tighten clamp.
18) Slide hose clamp (2) on hose (1), insert elbow (30) into hose and tighten clamp. 10
19) Repeat 17 and 18 for the opposite side.
20) Install steel clamp (35) on the end of boom pipe (36).
21) Install nut (31) on elbow (30) , turn the nut up to the end of the thread on elbow nozzle.
22) Pass elbow (30) through hole of steel clamp (35).
23) Install o'ring (33) on filter (32). Insert filter (32) in elbow (30) and install o'ring (33), nozzle
tip (5) and nut (34) on elbow. Hand tighten nut (34).
24) Turn nut (31) toward steel clamp (35). Do not over tighten. Adjust the nozzle spray
direction directly towards the ground.
25) Repeat 20, 21, 22, 23 and 24 for the opposite side.
26) Make sure all fittings are tight.
Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying.
YOUR SPRAYER IS READY TO USE.
NOTE: Read instruction manual and understand fully before operating the unit.
II) ASSEMBLY INSTRUCTION FOR 15 GAL. SPOT, ITEM # 8001604 (P. 35 & 36)
1) Install lid and outlet plug on tank (14) with tether straps. Use Teflon tape on all pipe thread
fittings.
2) Mount pump (3) to tank using screws (5) and washers (4).
3) Install grommet (8) on tank (14).
4) Insert hose (7) through grommet (8).
Note: Place hose in bottom of tank, so that it does not curl upward.
5) Slide hose clamp (6) on hose (7) insert the hose to hose barb on pump
and tighten clamp. From inside tank install barb (9) and strainer (10) to hose (7).
6) Install clips (16) to tank (14) using screws (15).
7) Slide hose clamps (6) on hose (1) insert the hose on barb on the pump and tighten the clamp.
Slide hose clamp on opposite end of hose and connect to barb on the wand (2).
8) Plug wire (18) to wire from pump.
9) Make sure all fittings are tight.
Note: Sprayer wand replacement tip # 8 is provided for precise spot spraying.
YOUR SPRAYER IS READY TO USE.
NOTE: Read instruction manual and understand fully before operating the unit. 11
II OPERATION
Read operation instruction manual and run the sprayer using water only for test.
1) This sprayer is designed to be used with a garden tractor or ATV.
2) The pumping system draws solution from the tank to the pump. The pump
forces the solution under pressure to the boom or wand.
3) Make sure the toggle switch is in the off position.
4) Install the red wire to a "hot" connection on the vehicle with a 12 volt DC power source or
the positive 12 volt battery post. The black wire should be grounded or connected to the
negative battery post.
5) Add clean water into tank so that the unit can be tested. Turn the toggle switch to the “on”
position and open the valve for either the boom or wand. Adjust the desired pressure by
slowly opening or closing valve, which has the hose that returns to the tank.
6) The wand or boom may be shut off at anytime when the pump system is
running, as the system is protected by an internal relief in the pump. It is best to
turn off the pump when it is not in use, to conserve energy from the battery.
7) The height of the boom needs to be adjusted so that there is 50% overlap on the
spraying surface (see diagram).
If you need to reduce the width to fewer nozzles, remove the nozzle tip and install the plug
that is provided. Not applicable to the boominator nozzle. The spray width is adjusted by
lowering or raising the boominator nozzle.
12
8) If it becomes necessary to clean the filters or nozzles, remove the filter from the nozzle body.
The filter sceen may now be tapped or flushed with clear water for cleaning. Nozzles can be
cleaned by soaking in water and cleaning with a brush and airline. Never blow through by
mouth or poke with wire or pins. Not applicable to the boominator nozzle. The
boominator nozzle should never need cleaning.
9) WARNING: Some chemicals will damage the valves if allowed to soak untreated for a
length of time. Always flush the pump with water after use. Do not allow chemicals to sit in
pump for extended times of idleness. Flushing may be done by adding water to the tank and
opening the sprayer valve (the hose that flows into the boom and wand) and run your motor
for 30-60 seconds. Follow chemical manufacturers instructions on disposal of all waste
water from the sprayer.
NOZZLES
HEIGHT
50 %
OVERLAP
SPRAYING
SURFACE
III CALIBRATION
1) Chemical labels may show application rates in gallons per acre, gallons per 1000 square feet,
gallons per 100 square feet, or litres per hectare. The TIP CHART on the next page shows
gallons per acre and litres per hectare ratings. If your chemical labels use 1000 or 100 square
feet use the gallons per acre with the following conversion:
- For 1000 square feet: divide by 43.56
- For 100 square feet: divide by 435.6
2) Once you know how much you are going to spray then determine (from the TIP CHART) the
spray pressure (PSI), spraying speed (MPH), and spray width (INCHES) [1 foot = 12 inches].
The weather condition must be considered when setting the sprayer.
3) Determining the proper speed of the tractor can be done by marking off 100, 200,
and 300 feet. The speed chart indicates the number of seconds it takes to travel the distances.
Set the throttle, and with a running start travel the distances. Adjust the throttle until you
travel the distances in the number of seconds indicated by the speed chart. Once you have
reached the throttle setting needed, mark the throttle location so you can stop and go again
(returning to the same speed).
SPEED CHART
Speed in M.P.H. Time Required in Seconds to Travel a Distance of:
(Miles per Hour) 100 ft. 200 ft. 300 ft.
4.0 17.0 34 51
5.0 14.0 27 41
6.0 11.0 23 34
8.0 8.5 17 26
10.0 6.8 14 20
12.0 5.7 11 17
14.0 4.9 10 15
16.0 4.3 9 13
20.0 3.4 7 10
13
4) Add water and proper amount of chemical to tank and drive to the starting place for spraying.
Adjust pressure with pressure adjusting valve to the pressure required. This must be
determined from the nozzle tip chart and application rate recommended by the chemical
manufacturer.
WARNING: Read your chemical supplier warning labels.
CAUTION: - Do not spray on windy days.
- Protective clothing must be worn when spraying hazardous
chemicals.
- Be sure to read and understand this manual before spraying.
TIP CHART FOR RED DEFLECTIP NOZZLE
FLOW RATE PER NOZZLE
TIP CHART FOR BLUE FAN TIP NOZZLE
FLOW RATE PER NOZZLE
14
TIP CHART FOR THE GREY DEFLECTIP NOZZLE
FLOW RATE PER NOZZLE
Gal
/
Acre L/Ha Gal
/
Acre L/Ha Gal
/
Acre L/Ha Gal
/
Acre L/Ha Gal
/
Acre L/Ha Gal
/
Acre L/Ha Gal
/
Acre L/Ha
15 0.25 12.1 114 9.1 86 7.3 69 6.1 57 5.2 49 4.5 42 4.0 38
20 0.28 14.0 132 10.5 99 8.4 79 7.0 66 6.0 56 5.3 50 4.7 44
25 0.32 15.7 148 11.7 110 9.4 88 7.8 73 6.7 63 5.9 55 5.2 49
30 0.35 17.2 162 12.9 121 10.3 97 8.6 81 7.4 70 6.4 60 5.7 54
35 0.37 18.5 174 13.9 131 11.1 104 9.3 87 7.9 74 6.9 65 6.2 58
3 MPH 4 MPH 9 MPH
Liquid
Pressure
PSI
Capacity
GPM per
Nozzle
7 MPH6 MPH5 MPH 8 MPH
Gal
/
Acre L/Ha Gal
/
Acre L/Ha Gal
/
Acre L/Ha Gal
/
Acre L/Ha Gal
/
Acre L/Ha Gal
/
Acre L/Ha Gal
/
Acre L/Ha
15 0.37 18.2 171 13.6 128 10.9 102 9.1 86 7.8 73 6.8 64 6.1 57
20 0.42 21.0 197 15.7 148 12.6 118 10.5 99 9.0 85 7.9 74 7.0 66
25 0.47 23.5 221 17.6 165 14.1 133 11.7 110 10.1 95 8.8 83 7.8 73
30 0.52 25.7 242 19.3 181 15.4 145 12.9 121 11.0 103 9.6 90 8.6 81
35 0.56 27.8 261 20.8 196 16.7 157 13.9 131 11.9 112 10.4 98 9.3 87
3 MPH 4 MPH 9 MPH
Liquid
Pressure
PSI
Capacity
GPM per
Nozzle
7 MPH6 MPH5 MPH 8 MPH
Gal/
Acre L/Ha Gal/
Acre L/Ha Gal/
Acre L/Ha Gal/
Acre L/Ha Gal/
Acre L/Ha Gal/
Acre L/Ha Gal/
Acre L/Ha
30 0.25 10.4 98 8.7 82 7.4 70 6.5 61 5.2 49 4.3 40 3.7 35
40 0.28 12.0 113 10.0 94 8.6 81 7.5 71 6.0 56 5.0 47 4.3 40
45 0.32 12.8 120 10.6 100 9.1 86 8.0 75 6.4 60 5.3 50 4.6 43
50 0.35 13.5 127 11.2 105 9.6 90 8.4 79 6.7 63 5.6 53 4.8 45
60 0.37 14.7 138 12.3 116 10.5 99 9.2 86 7.4 70 6.1 57 5.3 50
5 MPH 6 MPH 14 MPH
Liquid
Pressure
PSI
Capacity
GPM per
Nozzle
10 MPH8 MPH7 MPH 12 MPH
TIP CHART FOR THE BOOMINATOR NOZZLE
TESTED HEIGHT 36”, SPRAY WIDTH 16 FEET
Gal/
Acre L/Ha Gal/
Acre L/Ha Gal/
A
cre L/Ha Gal/
A
cre L/Ha Gal/
A
cre L/Ha Gal/
Acre L/Ha Gal/
Acre L/Ha
20 1.5 46 432 23 216 16 150 12 113 8.0 75 7.5 71 6.5 61
30 1.7 53 498 26 244 18 169 13 122 11 103 9.0 85 8.0 75
40 2.0 62 583 31 291 21 197 16 150 12 113 10 94 9.0 85
1 MPH 2 MPH 7 MPH
Liquid
Pressure
PSI GPM 5 MPH4 MPH3 MPH 6 MPH
V AFTER SPRAYING AND WINTER STORAGE
1) Fill half the tank with water and run the pump until clear water comes out
at the nozzle end.
2) Flush the system with a chemical neutralizing agent.
NOTE: Follow the chemical manufacturers disposal instructions on
washing or rinsing water and chemicals.
3) If you are not using it for a long period of time remove nozzle tips and filter.
- wash nozzle tips with water or cleaning solution.
- blow out orifice.
- clean and dry.
NOTE: If orifice remains clogged, clean it with a fine bristle brush. Never blow
through by mouth or poke with wire or pins or you will damage the orifice.
- water rinse and dry tips before storing.
4) The sprayer should be winterized before storage by pumping a 50-50 solution of
water and anti-freeze through the entire plumbing. Proper care and maintenance
will prolong the life of the sprayer.
5) The sprayer should not be stored outside, the pump could get damaged from rain.
15
VI TECHNICAL SPECIFICATIONS
Item # Tank Tires Pump Boom Type Nozzle Type Approx.
Spray Width
5740063 15 US Gal.
Polyethylene N/A
1.4 gpm Open Flow, Viton
Valves, Santoprene Diaphragm,
60 psi Internal By-pass, Built in
on/off Switch
,
12 vdc
,
N/A N/A N/A
8002001 15 US Gal.
Polyethylene 4.10/3.50-4
Pnuematic
1.4 gpm Open Flow, Viton
Valves, Santoprene Diaphragm,
45 psi Internal By-pass, 12 vdc 40" Boom Ball Check Strainer, #3
Orifice, 110 Degree
Flooding Tip 120"
8034879 15 US Gal.
Polyethylene N/A
1.4 gpm Open Flow, Viton
Valves, Santoprene Diaphragm,
60 psi Internal By-pass, Built in
on/off Switch
,
12 vdc
N/A Brass/Plastic
Boominator nozzle,
model 1200BPS 192"
8002029 25 US Gal.
Polyethylene 4.10/3.50-4
Pnuematic
1.4 gpm Open Flow, Viton
Valves, Santoprene Diaphragm,
45 psi Internal By-pass, 12 vdc 10' Fold-up Ball Check Strainer, #2
Orifice, 105 Degree
Flooding Tip 200"
8002047 25 US Gal.
Polyethylene N/A 1.4 gpm Open Flow, Viton
Valves, Santoprene Diaphragm,
45 psi Internal By-pass, 12 vdc 10' Fold-up Ball Check Strainer, #2
Orifice, 105 Degree
Flooding Tip 200"
8002065 25 US Gal.
Polyethylene 13.00/5.00-6 1.4 gpm Open Flow, Viton
Valves, Santoprene Diaphragm,
45 psi Internal By-pass, 12 vdc
10' Spring
Loaded
Quick Change With Ball
Check Strainers, #3
Orifice, 110 Degree Fan
Ti
p
180"
8034888 25 US Gal.
Polyethylene 13.00/5.00-6 3.0 gpm Open Flow, Viton
Valves, Santoprene Diaphragm,
45 psi Demand Switch, 12 vdc N/A Brass/Plastic
Boominator nozzle,
model 1200BPS 192"
8001604 15 US Gal.
Polyethylene N/A 1 gpm Open Flow, Viton Valves,
Santoprene Diaphragm, 40 psi
demand Switch, 12 vdc N/A N/A N/A
1
2
3
4
5
6
7
8
9
10
11
1PUMP SHURFLO 1
2ELBOW NYLON .375 NPT X .50 1
3 NUT SWIVEL NYLON KNURLED .75 3
4BARB NYLON .375 FLAT SEAT 3
5NIPPLE REDUCER NYLON .50 X .375 1
6WASHER VINYL .62 ID X 1.0 OD X .13 THK 3
7TEE NYLON .50 NPTF X .25 NPTF 1
8VALVE PLAST .75 FGHT X .75 MGHT
DOUBLE 1
9ADAPTOR NYLON .75 MGHT X .50 NPTM 2
10 GAUGE PRESSURE 0-100 PSI .25 NPTM 1
11 VALVE PLST .75 FGHT X .75 MGHT 1
No. Description Qty
3 4 6 6 4 3
1
2
3
4
5
6
78
9
10
11
12
1ELBOW NYLON .375 NPT X .50 1
2PUMP SHURFLO 1
3 NUT SWIVEL NYLON KNURLED .75 3
4BARB NYLON .375 FLAT SEAT 3
5ELBOW NYLON .25 NPT STREET 1
6NIPPLE REDUCER NYLON .50 X .375 1
7GAUGE PRESSURE 0-100 PSI .25 NPTM 1
8WASHER VINYL .62 ID X 1.0 OD X .13 THK 3
9TEE NYLON .50 NPTF X .25 NPTF 1
10 VALVE PLAST .75 FGHT X .75 MGHT
DOUBLE 1
11 ADAPTOR NYLON .75 MGHT X .50 NPTM 2
12 VALVE PLST .75 FGHT X .75 MGHT 1
No. Description Qty
34884
3
PUMP ASSEMBLY USED ON SPRAYER
5740063, 8034888, 8002029, 8002065 AND 8002001.
PUMP ASSEMBLY USED ON SPRAYER 8002047 AND 8034879
16
PLUG #12 REPLACES
THESE PARTS FOR
SPRAYER 5740063
18
PARTS LIST
SPRAYER 25 GAL PULL TYPE
ITEM #8002029
No. Item No. Description Qt
y
1 1900063 BOOM LEFT ARM INSIDE 1
2 9803271 BOLT HEX .250-20 UNC X .75 LG 4
3 9856592 NUT HEX .250-20 UNC GR 5 PTD 4
4 9852351 WASHER PTD .281 ID X .625 OD 8
5 1900060 BOOM ARM LEFT OUTSIDE 1
6 9227919 NUT LOCK NOZZLE BODY NYLON .688 FPS 4
7 9213802 FUSE BOX INLINE 14 GA C/W 10A 1
8 5710089 HOSE CLEAR BRAIDED .375 ID X .59 OD X 39" LG 2
9 9803826 BOLT HEX .375-16 UNC X 1.75 LG GR 5 PTD 2
10 1900106 FRAME BOOM 1
11 9852484 WASHER PTD .687 ID X 1.75 OD 2
12 2020060 WHEEL 4.10/3.50-4 X .625 AXLE 2
13 9857558 NUT LOCK UNITORQ .375-16 UNC 4
14 9803511 BOLT HEX .312-18 UNC X .625 LG GR 5 PTD 4
15 9853342 WASHER LOCK SPLIT REG .312 PTD 4
16 9852377 WASHER PTD .344 ID X .688 OD 4
17 1900105 FRAME 25 GAL SPRAYER 1
18 9803792 BOLT HEX .375-16 UNC X 1.00 LG GR 5 PTD 2
19 1900068 FRAME TOW S/ASSY 1
20 10000656 DECAL SPRAYER CAUTION 1
21 9227513 GAUGE PRESSURE 0-100 PSI .25 NPTM 1
22 9213778 WIRE ELEC. RED 14 GA X 6 FT 1
23 9255605 TEE NYLON .50 NPTF X .25 NPTF 1
24 9227943 SWITCH TOGGLE 15 AMP 125DCV 1
25 9255647 BARB .375 X .688 THREAD 1
26 9237991 ELBOW NYLON .375 NPT X .50 1
27 9213810 PUMP SHURFLO 1
28 9227828 HOLDER SWITCH 1
29 9106709 ON/OFF PLATE 1
30 9227489 ADAPTOR NYLON .75 MGHT X .50 NPTM 2
31 9227422 VALVE PLAST .75 FGHT X .75 MGHT DOUBLE 1
32 9255712 CLIP GRIPPER.38-.63 RANGE 2
33 5710089 HOSE CLEAR BRAIDED .375 ID X .59 OD X 19.5" LG 1
34 9842246 SCR MACH RD HD #10-24 UNC X 1.00 LG 4
35 9227414 BARB NYLON .375 FLAT SEAT 3
36 9227901 NUT SWIVEL NYLON KNURLED .75 3
37 9227455 ELBOW NYLON .687 MPS X .50 BARB 2
38 9227372 CLAMP HOSE NYLON 19/32 14
39 9213620 FILTER BALL CHECK NOZZLE 100 MESH 4
40 9400144 O RING BN .625 X .500 8
41 9231606 NOZZLE DEFLECTIP RED 4
42 9227463 NUT NOZZLE SEAT CAP NYLON .688 MPS 4
43 1900059 BOOM ARM RIGHT OUTSIDE 1
44 9255639 STRAINER 50 MESH .330 ID 1
45 9255621 BARB NYLON .375 X .500 1
46 9237959 CLAMP HOSE NYLON .75 1
47 10000611 GROMMET RUBBER .75 ID X 1.38 OD 1
48 5710090 HOSE CLEAR BRAIDED .50 ID X .75 OD X 30" LG 1
49 5710089 HOSE CLEAR BRAIDED .375 ID X .59 OD X 19.5" LG 2
50 1900062 BOOM RIGHT ARM INSIDE 1
19
51 9231614 TEE NYLON NOZZLE SEAT 2
52 9227430 BARB NYLON .375 TEE 1
53 9217951 INSERT SQ RIBBED 1.00 X 14-20 1
54 9232943 BOLT CARR .250-20 UNC X 1.00 LG GR 5 PTD 4
55 1900107 FRAME SLIDE BOOM 1
56 9853334 WASHER LOCK SPLIT REG .25 PTD 8
57 9858499 NUT WING .25-20 UNC PTD NON STAMP TYPE 4
58 5710089 HOSE CLEAR BRAIDED .375 ID X .59 OD X 210" LG 1
59 9228008 WAND SPRAYER C/W ADJ. TIP 1
60 9840000 SCR MACH RD HD #10-24 UNC X .31 LG 2
61 9255613 VALVE PLST .75 FGHT X .75 MGHT 1
62 9228016 WASHER VINYL .62 ID X 1.0 OD X .13 THK 4
63 9227729 NIPPLE REDUCER NYLON .50 X .375 1
64 5710089 HOSE CLEAR BRAIDED .375 ID X .59 OD X 27" LG 1
65 9213794 WIRE ELEC. BLACK 14 GA X 6 FT 1
66 9233594 SCREW THUMB BLACK 1
67 9232372 PIN .375 X 2.5 USEABLE LENGTH 1
68 4212049 CABLE TIE NYLON 6.75 4
69 9255720 TANK 25 GAL BLOW MOLDED 1
70 9160813 DECAL PAL SERIAL # 1
71 9860388 COTTER PIN .187 X 1.50 PLAIN 2
72 10000661 DECAL SPRAYER 25 GAL POWERFIST 1
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/