33
Table of Contents
What is sensiLift™ 4
How Does it Work? 4
sensiLift™ Description 4
Device Description 5
User Interface Description 6
User Instructions 7
Device Set-Up 7
What to Expect When Using sensiLift™ 7
How to Use sensiLift™ 8
Preliminary Test 9
Treatment Areas 10
Treatments Schedule 11
Post Facial Treatment Care 11
Cleaning & Troubleshooting 12
When Shouldn’t sensiLift™ Be Used? 13
Possible Side Effects 16
Frequently Asked Questions 17
Device Specification Parameters 18
© All rights reserved to Home Well Trading Ltd.
4
What is sensiLift™
sensiLift™ is a home use device intended for
wrinkles reduction and elasticity renewal
based on selective electrothermolysis (RF)
combined with mechanical massage for
immediate relaxation of the facial skin.
How Does it Work?
Introducing the new Dynamic RF™ technology
Dynamic RF™ technology combination
of RF with facial massage maximizes the
effectiveness of the RF treatment, allowing
multiple RF waves to reach wider range of
skin layers and assist in getting best possible
visible and ongoing, lasting results.
A major cause of skin wrinkles is the
reduction in the quantity and quality of
collagen fibers in the dermis and hypodermis.
Radio Frequency (RF) is a form of
electromagnetic energy that has being used
in doctors clinics for a long time and was
found to produce a highly efficient thermal
effect on biological tissue.
Heat is generated as a result of tissue
resistance to the movement of electrons
within the RF field. Then the sub-cutaneous
heat generates new collagen and enhances
existing collagen, leading to wrinkle
reduction and improved skin elasticity.
sensiLift™ treatment creates enough thermal
effect to induce some collagen remodeling
with no ablative thermal damage of the
epidermis or dermis.
sensiLift™ Description
sensiLift™ kit includes the following main
components:
1. External power supply
2. sensiLift™ hand-held device:
Massage fingers and electrodes - the
two massage fingers (treatment fingers)
combined with RF electrodes in order to
simultaneously apply the RF and massage
treatment. safety temperature sensors are
also embedded in the treatment fingers.
3. sensiLift™ conductivity enhancer:
Designed especially to improve contact
between the device and the skin and
improve skin conductivity.
6
Status Indicator
Blinking yellow light
sensiLift™ is on Stand-by mode.
In case of no light, make sure the
power cord is plugged-in properly.
Steady yellow light
before treatment
Energy level selected (1-3) is ON
you can start your treatment.
Steady green light
sensiLift™ is on Treatment mode,
RF is activated, skin contact is
detected and the treatment is
undergoing.
Blinking alternating
green and yellow
sensiLift™ is on Error mode, the
device detected a malfunction and
prevents
the activation of the RF and
Massage functions.
RF energy level
selection touch
button
Energy levels 1-3
lights
Green light on, indication of RF
energy level. Press the RF energy
level selection button repeatedly
until you reach the desired level:
1, 2, 3 or off.
Massage level
selection touch
button
1-2 massage level
lights
Green light on, indication of
massager function level. Press the
massage level selection button
repeatedly until you reach the
desired level: 1, 2, or off.
User Interface Description
7
User Instructions
sensiLift™ is ideal for treating areas such as
your cheeks, nasolabial “smile” folds, the
“crow’s feet” next to your eyes, the forehead,
chin, neck and décolletage.
Device Set-Up
• Remove all components from the box
(sensiLift™ device, power supply and
sensiLift™ conductivity enhancer).
• Before beginning the treatment make sure
the treatment fingers are clean,
dry and intact.
• Plug the external power supply to the
electric outlet.
• Only after plugging the power supply to
the electric outlet, plug the other end of the
power cord into the device power socket
(see image - item 8).
sensiLift™ is now ready to be used
What to Expect When Using
sensiLift™
• Sensations of warmth during session of
treatment - created by the RF energy during
treatment.
• Some mild red or pink color to the skin -
during and just after using sensiLift™.
Before you Begin
• Make sure your skin is dry, clean and free
of topical products (such as moisturizers),
liquids or lint. For male users, also make
sure your skin is clean and shaved.
• Use a mirror to assist you during treatment.
Before beginning the treatment make sure
the treatment fingers are clean,
dry and intact.
8
How to Use sensiLift™
Note:
A preliminary test should be conducted
before proceeding to a full treatment. See
“preliminary test section” below.
1. Apply a thin, even layer of sensiLift™
conductivity enhancer included in your kit,
on the area of your skin intended
for treatment.
2. Set the Radio Frequency (RF) energy
level and the massage speed to the
level you selected in your preliminary
test treatment. Press the RF energy level
selection button (see image - item 7)
repeatedly until you reach the desired
level: 1, 2, or 3. Press the button (see
image - item 3) repeatedly until you reach
the desired level: 1 or 2.
3. The activation of either RF or massage
functions can be done independently or
together. Both functions will be activated
at level 1. Select different levels based on
the “preliminary test”.
4. sensiLift™ is equipped with 2 safety
sensors which will keep the temperature
in the effective and safe range during the
whole treatment.
5. Place the treatment fingers (see image -
item 2) on the intended area, ensuring full
contact with your skin during the entire
treatment. sensiLift™ will indicate the
proper skin contact by the green status
light. If sensiLift™ is not properly placed,
the RF energy will not be delivered.
6. If you do not feel sensations of warmth
after approximately 10 seconds, try
moving sensiLift™ on a smaller treatment
area, and/or increasing the RF energy.
7. Move the device on the treated area with
slow circular or back and forth motion
while constantly and firmly contacting
the skin.
8. See treatment areas, treatment time and
treatments schedule in the “treatment
protocol” section below.
9. Turn off the device and then unplug at the
end of each treatment session.
10. After completing the treatment, wipe
off the sensiLift™ conductivity enhancer
from the treated area.
11. Cleaning instructions for before and
after are detailed (as depicted in the
Cleaning section).
9
Preliminary Test
Before your first treatment, and in order
to find the best sensiLift™ settings for
you, a preliminary test on a small patch
of skin in the intended treatment area is
recommended.
Do a preliminary test on each area you intend
to treat 48 hours prior to the full treatment.
• Before using sensiLift™, apply a thin, even
layer of sensiLift™ conductivity enhancer on
treated area.
• Start your test with RF energy level 1 and
massage level 1.
• Increase the levels according to your comfort.
• The treatment will create a warm sensation
on your skin.
• Stop the test if you do not feel comfortable
or if you see adverse effects such as severe
redness or blistering.
• If the skin in the test area seems normal
(no adverse effects) you can proceed with
a full treatment in the highest comfortable
energy level and massage level you tested.
Note:
The RF energy level indicates the rate
at which the temperature rises when in
heating mode. A high RF energy level will
enable you faster and even heating. You
can achieve maximum results with all RF
energy levels (for lower levels, it will just
take longer time to reach the effective
temperature), therefore, select your
optimal RF energy level according to your
level of comfort.
10
Treatment Areas
Do not treat full areas with energy levels
you have not tested before
Forehead and between the eyes
(treatment area 1)
• Place the treatment fingers
on the area as indicated in
the picture.
• Keep moving sensiLift™
up and down across the
forehead area.
• The recommended treatment
time for this area is 10 minutes.
“Crow’s feet” (around the eyes) treatment
(treatment area 2)
• Place the treatment fingers
on the area as indicated in
the picture.
• Keep moving sensiLift™ in
continues slow ‘side to side’
circular motion.
• Avoid areas such as inside
the nostrils, eye cavity and oral cavity, as
treatment in these areas may cause
adverse effects.
• Avoid contact with the eyes.
• The recommended treatment time for this
area is 10 minutes (on each side).
Cheek and nasolabial “smile” folds
treatment (treatment area 3)
• Place the treatment fingers
on the area as indicated in
the picture.
• Move sensiLift™ in slow
circular motions across the
cheek area and up and down
over the “smile folds”.
• The recommended treatment
time for this area is 10 minutes (on each side).
11
Chin treatment (treatment area 4)
• Place the treatment fingers
on the area as indicated in
the picture.
• Keep moving sensiLift™ from
one side of the chin to the other.
• T
he recommended treatment
time for this area is 10 minutes.
Neck treatment (treatment area 5)
• Place the treatment fingers
on the area as indicated in
the picture.
• Keep moving sensiLift™ up
and down across the neck area.
• The recommended treatment
time for this area is 10 minutes
• CAUTIONS: Avoid treatment
in the lower third of the neck since this area
is more sensitive, avoid from treating the
thyroid area (marked ).
Décolletage treatment (treatment area 6)
• Place the treatment fingers on the area as
indicated in the picture.
• Keep moving sensiLift™ in slow circular
motions across the décolletage area.
• The recommended treatment time for this
area is 10 minutes.
Treatments Schedule
• For long lasting skin tightening results, use
sensiLift™ once a week on each area for a
period of 8 weeks.
• Response to sensiLift™ treatment differs
between individuals depending on
environmental and biological factors,
heredity and aging.
• sensiLift™ results can provide long term
effect. Additional treatments may be
repeated for maintenance.
Post Facial Treatment Care
• After completing the treatment, wipe off
the sensiLift™ conductivity enhancer from
the treated area.
• We recommend you use the sensiLift™ post
treatment enhancer to increase treatment
efficacy and long lasting results.
• Apply a high-factor sunscreen (at least
30 SPF) and protect the treated area from
sunlight for two weeks following treatment.
• Following treatment, avoid the use of hot
12
water and discontinue use of abrasive or
harsh products for two days.
• In cases where superficial crusting or
scabbing occurs, do not rub, scratch or
remove the scab. Cleanse the area gently
and pat dry.
• Makeup may be applied immediately after
treatment.
Cleaning & Troubleshooting
Cleaning
• Make sure to turn off and unplug unit
before cleaning.
• Clean sensiLift™ from residual of sensiLift™
conductivity enhancer with a soft damp
cloth or paper towel. Make sure all
electrodes area including the temperature
sensors, silicone cover, are cleaned
thoroughly.
• Make sure sensiLift™ is completely dry
before storing it; never submerge the
device or any of its parts in water as it may
lead to electrocution.
• Store sensiLift™ in a safe and protective
place.
Troubleshooting
If you experience any problems with
sensiLift™, please refer to the information
below to try to resolve it:
• If sensiLift™ does not turn on:
Make sure that the power cord is plugged
properly into the electrical outlet and into
the device power socket.
• If sensiLift™ does not deliver RF signal
energy (you cannot feel a warm sensation):
Verify there is full contact with the skin
and the sensiLift™ conductivity enhancer
was applied on the skin. The RF signal
will activate only when the treatment
fingers are in full contact with the skin.
See Indicator stated in “User Interface
Description” section.
If you still have problems with your device,
please contact our customer service.
13
When Shouldn’t sensiLift™ Be
Used?
WARNINGS
• Do not open or repair the device as it
contains dangerous electrical components,
which may cause physical damage.
• Do not use sensiLift™ near bathtubs,
showers, basins or other vessels containing
water or other humid environments as it
may lead to electrocution.
• Do not use sensiLift™ without applying the
sensiLift™ conductivity enhancer
before use.
• Do not use the device if:
• The device is not working properly,
appears damaged or broken
• The cord or plug are damaged
• You see or smell smoke
• The outer shell is damaged or loose
• RF electrodes are damaged
• NEVER use flammable liquids such as
alcohol or acetone to clean the skin before
using sensiLift™ as it may cause burning of
the skin.
• Do not use sensiLift™ if you have an active
implant such as a pacemaker, insulin
pumps, or similar devices since it may
cause interference.
• The use of sensiLift™ by pregnant (suspicion
of pregnancy) or nursing women has not
been established.
• Do not use if you have skin cancer or on
areas at risk of malignancy.
• Do not use if you suffer from blood
coagulopathy or excessive bleeding
or bruising.
• The use of sensiLift™ by someone
using blood-thinning medication
(anticoagulants), including fish oil, garlic
supplements etc. has not been established.
• Do not use if you have a history of deep
vein thrombosis at the treatment area.
14
CONTRAINDICATIONS
THE CONSEQUENCES OF THE
FOLLOWING CONTRAINDICATIONS
ARE NOT YET ESTABLISHED AND
MAY CAUSE ADVERSE EFFECT
• Do not use if you are under the age of 18.
• Do not use if you have been taking drugs
that influence the immune system.
• Do not use if you have impaired immune
system (as HIV).
• The use of sensiLift™ by someone under
radiation therapy or chemotherapy
within the past 3 months has not
been established.
• Do not use on if you have heat induced
disease (Herpes, etc.) in the treatment area.
• Do not use if you have an active skin
disease in the treatment area (such as
Herpes, Eczema, rash).
• Do not use if you suffer from keloid scar
formation or impaired wound healing.
• Do not use if you suffer from extra dry or
sensitive skin.
• Do not use if you have been taking
Accutane in the past 6 months.
• Do not use if you suffer from endocrine
disorder (such as diabetes and uncontrolled
thyroid disease).
• Do not use if you suffer from hepatitis or
liver disease.
• Do not use on sunburns in the treatment
area as this can cause serious burns or
skin injury.
• Do not use if you have dark spots such
as large freckles, moles or blisters on the
treatment area.
• Do not use over mucous membranes as in
the nose, eye cavity and oral cavity as it may
cause burns.
• Do not use over piercing or any metal items
such as earrings or jewelry as it may
cause burns.
• sensiLift™ should not be used on tattoos,
permanent make up or intimate body areas
such as nipples, genitalia or around
the anus.
• Do not use if you have any permanent
implants in the designated treatment area
(including but not limited to: silicon or
injected chemical materials, metal plates or
other metal materials).
• Do not use if you had plastic surgery such
as face lifting or eyelid surgery within the
past 3 months.
15
• Do not use if you used augmentation
techniques with injected bio-materials in
the designated treatment area (such as
injections of Botulinum toxin, collagen
protein or fat).
• Do not use if you had a chemical peel
(Alpha hydroxyl acids AHAs such as glycolic
acid, Beta hydroxyl acid BHA, Jessner’s peel)
or natural filler (Hyaluronic acid, Collagen)
in the treatment area.
• Do not use if you had aesthetics or medical
surgery procedure in the treatment area
within the past 3 months or during the
healing process.
• Do not use if you had professional facial
abrasion (such as dermabrasion, facial
resurfacing, or deep chemical peeling
(Phenol, Trichloraacetic acid-TCA, and/or
ablative laser treatments) within the past
3-6 months till the final healing.
• Do not use if you suffer from sensitive
skin such as in cases of frequent redness,
inflammations, breakouts, infection and
acne, as these conditions can get worse.
• In case of extreme redness of the skin,
blistering, or burns - stop use immediately.
CAUTIONS
• KEEP OUT OF CHILDREN’S REACH.
• sensiLift™ is not intended for use by
persons with reduced physical, sensory or
mental capabilities.
• Use sensiLift™ only with original external
power supply.
• Do not use sensiLift™ with any additional
accessories that are not part of its intended
use as there is no data supporting this kind
of use of the device.
• sensiLift™ is a home use device intended for
non-invasive treatment of mild to moderate
facial wrinkles and rhytides. Do not use for
any other purpose.
• Use sensiLift™ according to this User
Guide only.
• Do not leave sensiLift™ unattended when
plugged into an electrical outlet.
• If you have undergone any other aesthetic
procedures or there is any uncertainty
regarding potential side effects, consult
your physician before using sensiLift™.
• sensiLift™ is designed to be used by a single
16
user.
• Before using sensiLift™, make sure the
device is clean, dry and intact. Cleaning
instructions are detailed in the cleaning
section.
Possible Side Effects
When using sensiLift™ daccording to this
User Guide, side effects are rare. However,
every aesthetics procedure including the
usage of home use devices may cause some
degree of side effects. If any of the following
conditions appear and last more than 48
hours, you should consult your physician:
Degree of
Side Effects
Side Effects
Minor
Side-Effects
Local pain
Irritation
Redness
Sensitivity to touch
Allergic contact dermatitis
or sensitivity to the
sensiLiftTM conductivity
enhancer
Rare
Side-Effects
Mild Burns
Pigment Changes
Excessive Redness
Urticaria, Purpura or
Ecchymosis
Hematoma
Swelling
Extremely Rare
Side-Effects
Severe Burns
Infection
Bruising
Blistering
17
Frequently Asked Questions
Does sensiLift™ actually work?
Yes, sensiLift™ provides visible results for
ongoing wrinkle reduction with prolonged
use. In recent years the use of selective
electrothermolysis has been well established
in the aesthetic medicine field and is used by
leading doctors around the world.
Which facial areas can sensiLift™ be used on?
sensiLift™ is designed for wrinkle reduction
and elasticity renewal by applying RF
electrodes on areas such as neck,
décolletage, chin, cheeks, nasal labial,
forehead and around the eyes.
Is sensiLift™ safe for use?
Yes. sensiLift™ 2 unique temperature sensors
ensure safe treatment at all time. sensiLift™
has been tested clinically and approved by
dermatologists and physicians.
Does it hurt to use sensiLift™?
No. Using sensiLift™ will create a warm
sensation in the treated area. When correctly
used most users feel a sense of relaxation and
a heat sensation at the time of treatment. If
you feel pain and uncomforted you are not
using the device properly, refer to the User
Guide to ensure correct use.
When are results from sensiLift™ achieved?
You can achieve significant visible effect from
the first treatment! However, for ongoing
and prolonged skin tightening, treatment
should be repeated once a week for a period
of 8 weeks. Thereafter, treatments may be
repeated for maintenance.
How long after sun exposure can sensiLift™
be used?
You can use sensiLift™ 48 hours after sun
exposure. Do not use sensiLift™ on sunburns
as this can may cause burns or skin injury.
Is long term use of sensiLift™ dangerous for
my skin?
The use of RF has been well documented for
over 20 years. No side effects or damage from
long term use has been reported during
that time.
Can men use sensiLift™?
Sure! sensiLift™ is suitable for both men
and women. However, hair in the treated
area should be shaved. Hair may disrupt
electrodes’ full coupling with the skin and as
a result, may cause burns.
18
Storage Instructions
Storage and Transport Conditions
-25 ⁰C to 70 ⁰C
(-13⁰F to 158⁰F)
Temperature
10% to 90% RH at
55⁰C/131⁰F
Humidity
Non-condensing Pressure
Operational Conditions
5⁰C to 40⁰C
(41⁰F to 104⁰F)
Temperature
20% to 80% RHHumidity
10,000 ft
Max
Operating
Altitude
Device Specification
Parameters
The RF handheld device is powered by
(Bipolar RF) a 10±0.5 [Watt]
Frequency: 1±0.05 [MHz]
Selectable output power level: 3 levels
Mechanical massage: Implemented by
moving RF electrodes Speed: 50-100 RPM
Temperature sensors: RF heating is
automatically deactivated when skin
temperature reaches 40 [⁰C]/104[⁰F]. The
heating is reactivated when temperature
decreases.
Treatment area ~2.2 [cm2] / 0.34[In²]
External Power Supply: Input 100-240 [VAC],
50-60 [Hz], Output 9[VDC], 1.5[A]
Device Size and Weight: 122 [g], 173[mm] X
56.8[mm] X 53.1[mm] LxHxW
4.3 [Oz], 6.8[In] X 2.23[In] X 2.09[In] LxHxW
19
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference.
(2) This device must accept any interference
received, including interference that may
cause undesired operation.
Double insulation
Type BF equipment
Consult Instructions for use
Do not dispose
Keep away from eyes
Please read all warnings and safety
precautions prior to use
Do not use the sensiLift™ device
on tanned skin or after sun
exposure
Keep dry
VER-09APR14
Labeling
Sensica International
Home Well Trading Ltd.
450 Bath Road
Longford, Heathrow, UB7 OE8, UK
Tel: +44 (0)208 7578980
Fax: +44 (0)208 7578767
suppor[email protected]
visit us: www.sensica.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Unoisetion MS-76D1MAX Owner's manual
-
mychway WL-7005C Owner's manual
-
ARISTORM MS-55T1 Owner's manual
-
-
ARISTORM MS-45T2 Operating instructions
-
-
-
Unoisetion MS-4481 Owner's manual
-
-
