Gyrolock units may be fixed to normal or sloping ceilings, with the
telescopic section remaining vertical for correct video projector support.
When used as a wall mount the telescopic section works as an angled
support arm allowing clearance for the tilt and swivel movements. Units
can also be base mounted for rear projection or other applications.
Our range of projector adapter plates (order code GAP) is constantly
updated - see current list for latest projectors covered.
For video projectors up to 12Kg.
CEILING INSTALLATION - STANDARD GK1 UNIT
Establish the required projector to screen distance and fix the unit through the
holes provided in the mounting plate 1.
Adjust the telescopic section 2 as required and fully tighten screws.
PROJECTOR MOUNTING
Fix the adapter plate 3 to the video projector using the screws provided. Raise
the projector into position and engage it into the Trilok bayonet 4. Rotate the
projector a half turn (180°) then tighten the safety screw 5 into the arrow head
void. Hand tighten the two clamp screws 6 to lock the projector in place.
ADJUSTMENT
Using the pan, tilt and screen levelling functions adjust the projector alignment.
Finally tighten all dome headed screws using the allen key provided.
RANGE OF DIFFERENT DROP LENGTHS
The GK2 installers kit comes with alternative telescopic sections which
can be used in any combination to give 23-70cm adjustment, intended
particularly when working within suspended ceiling voids. The GK3
version has a longer telescopic section for use with high ceilings.
The GK4 version uses a CP2 Ceiling Plate and chrome column (cut to length), for
installations requiring long drops - there is no telescopic section with this model.
WALL MOUNTED INSTALLATION.
Set the Gyrolock unit so that it appears like the wall
version illustrated with the short telescopic mast
2
sloping as shown.
IMPORTANT, use only as illustrated with
the standard short telescopic mast
2
acting as the support arm.
Follow projector mounting and
adjustment instructions to
continue installation.
SAFETY. We recommend installation by a Qualified Tradesperson,
using masonry plugs or other reliable fixings to ensure safe installation.
- Consult your builder or architect if in doubt.
User Guide
Shown inverted
for base mounting
Bei Fragen wenden Sie sich an: tel: +49 (0)9131 9405 800 fax: +49 (0)9131 9405 80 99 e-mail: [email protected] web: www.unicol.de
Trilok Equipment
Docking System
®
Adapter plate
typical adapter plate shown
Standard
Gyrolock
Unit GK1
®
Shown set for
wall mounting
BASE MOUNTED INSTALLATION.
Remove the telescopic section
2 from
the mounting plate bracket
1 and reset
it into the slots as illustrated. Refit and
fully tighten the dome headed screws
with the allen key provided.
Follow projector mounting and
adjustment instructions to
continue installation.
®
1
2
6
4
5
3
Shown adapted for
close ceiling use
CAMERA SCREW FITTING - GK0.
For projectors with Camera Screw fittings,
remove knurled screw assembly
7 and
fix to projector. Ensure locking ring
8 is
loose and refit assembly and projector by
sliding into position as shown. Tighten
locking ring 8 to secure.
8
7
Follow adjustment instructions to
continue installation.
CLOSE CEILING INSTALLATION.
Remove the telescopic
section
2 and reconnect
the bottom half of the Gyrolock unit
directly to the mounting plate
1.
Follow projector mounting and
adjustment instructions to
continue installation.
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Aura GK2 WB, BW Mechanical Gaming Keyboard User manual
-
Gamdias AURA GK1 User manual
-
Jabra SP-CEIL-012 User manual
-
Vision TC2 7M2PHO Datasheet
-
3M X50 User manual
-
NEC W32-70 Installation guide
-
Philips 220X User manual
-
Vogel's PPC 1585 User manual
-
Procolor 095020 Datasheet
-
Vision TC2-15MCABLES Specification
