Lenoxx PARSIFAL 90 Instructions Manual

PARSIFAL 90 – 120

INOX | NERO | BIANCO

Page is loading ...

INSTRUCTIONS FOR USE, MAINTENANCE AND INSTALLATION FOR THE DOWNDFRAFT.

ATTENTION: The downdraft must only be installed from a qualified technician. Every responsibility

regarding installations from unauthorized persons will be declined.

Before proceeding with the downdraft installation, please read carefully these instructions.

Keep this booklet together with the downdraft.

WARNING

ATTENTION: When the downdraft is closed, do not put pots or other containers on it, in order to avoid

eventual spills in phase of opening.

The downdraft is equipped of a security system of micro-switches that blocks the movement of the downdraft

in case the cover would raise. In phase of closure of the downdraft, if some object is between the cover and the

work top, the raising of the cover will block the movement.

In order to reactivate the movement it will be sufficient to replace the cover and activate the desired command.

Do not let children or disabled people use the downdraft if not in presence of adults.

Before cleaning or performing any periodic maintenance of the downdraft always ensure the electric power is

turned off by removing the plug from the socket and turning the main switch to position 0 (OFF).

Do not connect the downdraft to any piping used for combustion appliances, such as burners, boilers or

fireplaces.

Check that the main power supply corresponds to the voltage required by the downdraft (see silver label on the

electric box).

Ensure that the electric system is correctly earthed and that the earth discharge works correctly.

When cooking do not use materials that could form high or unusual flames. Oil and fat used twice are

particularly dangerous and could easily catch on fire.

Do not prepare flambé dishes under the hood.

Respect local legislation and regulations issued by the relative authorities regarding the exhaust air when the

suction is operating.

Failure to respect and perform all the maintenance operations described in this booklet could cause a fire

hazard.

INSTALLATION

The suction of the downdrafts, regarding the traditional hoods, is penalized in the suction of the cooking vapors

of the front pots. For this reason the use of a panoramic glass ceramic top is suggested.

The downdraft can be used for both filtering and suction.

When the filtering function is operating, with air recycle, carbon filters must be used.

When the downdraft is used in the filtering function, there must be a suitable section for spillage of the air

s

uc

tion on the base of the kitchen.

When the suction function is operating, exhausting the filtered air on the outside, a suitable compensation

system must be used according to current standards in force. The diameter of the fume exhaust pipe must be the

same or greater than the diameter of the downdraft pipe union.

There must be sufficient ventilation in the room where the downdraft is installed, to allow the simultaneous use

of other appliances that use gas or other fuels.

ASSEMBLY INSTRUCTIONS

Make a hole in the downdraft approximately 50mm from the work top hole.

For the dimensions of the hole, see drawing here below.

In the INOX version, the gluing of the cover (as rule, use

the same material of the work top) of the downdraft,

must be performed in the same place after finishing the assembly of the downdraft.

The support for the gluing of the cover is supplied with the downdraft.

The controls must be assembled in order to guarantee an eventual attendance of technical assistance.

In the kitchen furniture, provide in front or behind of the downdraft a removable wall.

It is possible to connect on the front or on the back part of the downdraft a tube of diameter 150 or 200mm

according to the suction motor used. It is possible to connect on the side of the downdraft a tube of diameter

150mm on both sides and preferably on two heights.

The downdraft allows a height adjustment of the structure from 820mm to 900mm from the floor to under the

work top. This adjustment is possible by working on the feet and on the feet supports (Fig. 1).

As for the height adjustment of the moving part of the downdraft, see Fig. 2.

According to the thickness of the work top and the cover, it is possible to adjust of 33mm.

The difference in thickness between the work top and the cover must be at least 17mm.

This adjustment is possible by acting on the two nuts that secure the central pivot of the actuator (Fig. 3).

Fig. 3

ELECTRIC WIRING

Safety Instructions:

• Before any manipulation of the controller power cord (230 volt)

•

Before each operation, all devices connected

• Electrical connections must be performed by professionals

PARSIFAL CONTROL FUNCTIONS

PLEASE NOTE : THE SUCTION OF THE DOWNDRAFT CAN BE STARTED ONLY WHEN THE

DOWNDRFT IS COMPLETLY EXTRACTED.

BUTTON “A”

With suction motor turned on, every time the button is pressed the motor speed will be reduced of one

step.

BUTTON “B”

With the downdraft completely removed, the suction motor can be turned on and/or off.

While pressing the button long enough, the suction motor turns off automatically.

The activation of the timer is signaled by the blue flashing led and the suction motor turns off after 10

minutes.

BUTTON “C”

Wi

th suction motor turned on, every time the button is pressed the motor speed will be increased of one

step.

BUTTON "D"

By pressing the button once, the downdraft is completely extracted.

If the button is pressed while the downdraft is moving, the downdraft automatically stops.

To restart the movement, it is necessary to press button "D" or "E".

BUTTON “E”

By pressing the button once, the downdraft returns in completely.

If the button is pressed while the downdraft is moving, the downdraft automatically stops.

To restart the movement, it is necessary to press button "D" or "E".

If the button is pressed when the suction motor is on, the motor automatically turns off.

NOTES:

- After 100 working hours of the suction motor, the red led, positioned under button "B", will start to flash

indicating the need to wash the metal filters.

To cancel the filters alarm, when the suction motor is switched off, you must press button "A" long

enough.

- At first use it is necessary to start the remote control learning.

When the downdraft is turned off, keep button "C" pressed for a long time.

T

he remote control learning is indicated with the flashing alarm filters led.

If, within one minute there is a valid remote control code (sent by pressing any button of the

the remote control), the led will be on continuously for 3 seconds and then it will turn off, indicating

the proper learning.

USE AND MAINTENANCE

Before beginning any sort of cleaning and maintenance work, turn off the power of the downdraft by turning

the main switch to 0 (OFF).

Cleaning the metal filters

The metal filters fitted in the downdraft should be washed every 2-3 months depending on how much they are

used, using hot water and a non aggressive liquid detergent.

To access the metal filters, you must remove the cover from the downdraft. In order to remove the cover, take

the cover out from the downdraft and take off the cover lifting it upwards.

The metal filters can be removed using the special handle unhooking first the filter in the front part and pulling

up.

After washing the filters, they must be thoroughly dried and reassembled correctly.

Carbon filters

If the downdraft is used with the internal recycle filtering system, then active carbon filters must be used.

The active carbon in the filters traps the cooking smells.

Warning: The carbon filters can not be reused or washed and should be changed periodically (every 4 months if

the hood is used for two hours every day). Saturated filters cause fire hazards.

The carbon filters are placed underneath the metal filters.

For replacement, first remove the metal filters and then remove the carbon filters by using the handle of the

filter and pushing it towards the back. Then remove it by pulling upwards.

Cleaning the hood

If the downdraft is stainless steel, use specific products and rags for satin stainless steel (non-abrasive and / or

corrosive detergents free of chlorine), ensuring to clean in the same direction as the satin finish.

Do not use aggressive products, chemical solvents or derivatives of oil distillates that could leave oily traces

which could cause oxidation and polymerization.

The manufacturer is not responsible for damage to the surface of the downdraft due to failure to respect

these instructions.

Page is loading ...

Lenoxx PARSIFAL 90 Instructions Manual

This manual is also suitable for

Lenoxx PARSIFAL 90 Instructions Manual

in other languages

Other documents