Zurn-Wilkins 34-350XL Installation guide

ZURN WILKINS

1747 Commerce Way, Paso Robles, CA 93446 Phone:855-663-9876 Fax:805-238-5766

OUTDOOR INSTALLATION

The Model 350XL Backow Preventer may

be installed outdoors only if the device is pro-

tected against freezing conditions. Exposure

to freezing conditions will result in improper

function or damage to the device. The instal-

lation location must be kept above 32°F. All

the basic installation instructions apply.

 Installation  Testing  Maintenance Instructions

INSTALLATION INSTRUCTIONS

CAUTION: Installation of Backow Preventers must be performed by qualied, licensed

personnel. The installer should be sure the proper device has been selected for the par-

ticular installation. Faulty installation could result in an improperly functioning device.

ZURN WILKINS Model 350XL Double Check Valve assemblies are for use on potable

water lines where a health hazard does not exist in the event of a backow situation.

Damage to the device could result wherever water hammer and/or water thermal expan-

sion could create excessive line pressure. Where this could occur, shock arresters, check

valves and/or pressure relief valves should be installed downstream of the device.

If installation is in a pit or vault, the Backow Preventer must never be submerged in

water because this could cause a cross-connection. Make sure that the pit or vault always

remains dry by providing ample drainage.

1. Before installing a Model 350XL Backow Preventer, ush the line thoroughly to

remove all debris, chips and other foreign matter. If required, a strainer should be

placed upstream of the Backow Preventer. CAUTION: Do not use a strainer in

seldom used emergency waterlines such as re lines.

2. Provide adequate space around the installed unit so that the test cocks will be

accessible for testing and servicing.

3. Install valve at least 12 inches above surrounding ood level.

4. Always consult local codes for installation methods, approvals and guidance.

INDOOR INSTALLATION

Indoor installation is preferred in areas that

are subject to freezing conditions. All the

basic installation instructions apply to such

installations.

PLACING THE MODEL 350XL IN SERVICE

1. Start with both shut-off valves closed.

Slowly open the inlet shut-off valve until the

backow preventer is completely pressur-

ized.

2. When the unit has been pressurized,

vent any trapped air by slightly opening

each of the four test cocks.

3. Slowly open the downstream shut-off

valve. The Model 350XL Double Check

Valve assembly is now in service.

4. After the Model 350XL has been prop-

erly installed, test the device (see “TEST

PROCEDURES”). If the device fails the

test, remove the rst and second check

valves and thoroughly ush the device.

Clean rubber and seats of all debris and

place unit back in service.

VERTICAL INSTALLATION

Vertical installation is acceptable in appli-

cations where inlet and outlet piping are

owing vertically upwards. All the basic

installation instructions apply to such

installations. Consult factory for approval

status.

Model 350XL LEAD-FREE*

Double Check Valve Assembly (3/4” & 1”)

*This product contains a weighted average lead content less than 0.25% for wetted surfaces.

*Certied to NSF/ANSI 61-G

DIRECTION OF FLOW

WILKINS 350XL

DIRECTION OF FLOW

WILKINS 350XL

DIRECTION OF FLOW

WILKINS 350XL

PROTECTIVE

ENCLOSURE

DIRECTION OF FLOW

12" MIN.

30" MAX.

OPTIONAL LEAD-FREE STRAINER

(MODEL SXL)

WILKINS 350XL

www.zurn.com

Testing Procedures

ZURN WILKINS

1747 Commerce Way, Paso Robles, CA 93446 Phone:855-663-9876 Fax:805-238-5766

MODEL 350XL DOUBLE CHECK VALVE ASSEMBLY

Equipment Required: Differential pressure gauge test kit.

TEST NO. 1 - TIGHTNESS OF #1 CHECK VALVE

REQUIREMENT:

The static pressure drop across check valve #1 shall be at least

1.0 psid. If test cock #3 is not at the highest point of the check

valve body, then a vertical tube must be installed on test cock #3

so that it rises to the top of the check valve body.

PROCEDURE:

1. Slowly open all 4 test cocks to remove any foreign material

and attach ttings.

2. Attach hose from the high side of the test kit to the #2 test cock.

3. Open test cock #2 and bleed all air from the hose and gauge

by opening the high side bleed needle valve. Close high side

bleed needle valve. If a tube is attached to test cock #3, open

test cock #3 to ll the tube. Close test cock #3. Close #2

shut-off valve then close the #1 shut-off valve.

4. Hold gauge at same level as test cock #3 or water level in

tube. Slowly open test cock #3. Record the static pressure drop

across check valve #1 after gauge reading stabilizes and

water stops running out of test cock #3.

5. Close all test cocks, open shut-off valve #1 and remove test

equipment.

TEST NO. 2 - TIGHTNESS OF #2 CHECK VALVE

REQUIREMENT:

The static pressure drop across check valve #2 shall be at least

1.0 psid. If test cock #4 is not at the highest point of the check

valve body, then a vertical tube must be installed on test cock #4

so that it rises to the top of the check valve body.

PROCEDURE:

1. Attach hose from the high side of the test kit to the #3 test cock.

2. Open test cock #3 and bleed all air from the hose and gauge

by opening the high side bleed needle valve. Close high side

bleed needle valve. If a tube is attached to test cock #4,

open test cock #4 to ll the tube. Close test cock #4.

Close #1 shut-off valve.

3. Hold gauge at same level as test cock #4 or water level

in tube. Slowly open test cock #4. Record the static pressure

drop across check valve #2 after gauge reading stabilizes

and water stops running out of test cock #4.

4. Close all test cocks, slowly open shut-off valve #1 & #2 and

remove test equipment.

VENT HOSE

LOW SIDE HOSE

HIGH SIDE HOSE

LOW SIDE BLEED

NEEDLE VALVE

#1 TEST COCK

#2 TEST COCK

#3 TEST COCK

#4 TEST COCK

#1 SHUT-OFF

VALVE

#2 SHUT-OFF

VALVE

HIGH SIDE BLEED

NEEDLE VALVE

WILKINS 350XL

www.zurn.com

No. 1

Test Cock

No. 2

Test Cock

No. 3

Test Cock

No. 4

Test Cock

Housing

Inlet

Ball Valve

Outlet

Ball Valve

Body

#1 Check

Assembly

#2 Check

Assembly

Inlet

O-ring

Outlet

O-ring

#1 Check

O-ring

#2 Check

O-ring

Spring

Poppet

Tailpiece

Hex Flange Bolts

#1 Seat

#2 Seat

Maintenance Instructions

ZURN WILKINS

1747 Commerce Way, Paso Robles, CA 93446 Phone:855-663-9876 Fax:805-238-5766

FIGURE 1 FIGURE 2 FIGURE 3

Spring

Seat

Poppet

Tailpiece

CHECK ASSEMBLY

All Model 350XL Double Check Valve Backow Preventers must

be inspected and maintained by licensed personnel at least once

a year or more frequently as specied by local codes. Replace-

ment of worn or damaged parts must only be made with genuine

“ZURN WILKINS” parts.

GENERAL MAINTENANCE

1. Clean all parts thoroughly with water after disassembly.

2. Carefully inspect rubber seal rings and o-rings for damage.

3. Test unit after reassembly for proper operation (refer to

“TESTING PROCEDURES”).

SERVICING CHECK VALVES

1. Close inlet and outlet shut-off valves.

2. Open No. 2, No. 3 and No. 4 test cocks to release pressure

from valve.

3. Unscrew the 4 bolts (1/4-20 UNC Hex Flange) holding the

housing in place.

4. Using a #2 athead screwdriver, pry loose housing by placing

the screwdriver in the notch between housing and body.

5. Pull housing out of the body and remove checks by sliding

them towards the outlet of housing.

6. Using the same screwdriver, locate the notch between seat

and tailpiece of each check. Insert screwdriver and twist to

“snap” checks apart. CAUTION: Checks are spring loaded.

7. Inspect the rubber seal ring around poppet for cuts or

embedded debris.

8. If the poppet is damaged, replace with a new poppet.

9. Inspect the remaining check parts and seating areas.

Remove any debris.

10. If necessary, replace any damaged parts with new ones.

11. Lightly grease o-rings on checks and reinstall into housing

following the above procedures in reverse order.

12. Flush body prior to reinstalling housing.

13. Lightly grease o-rings on housing and reinstall into body

following the above procedures in reverse order.

Note: When installing housing, match slight taper on the outlet of

the housing with corresponding taper in body.

www.zurn.com

ZURN WILKINS

1747 Commerce Way, Paso Robles, CA 93446 Phone:855-663-9876 Fax:805-238-5766

MODEL 350XL 3/4" & 1" (STANDARD & METRIC)

0 20 40 60 80

FLOW RATES (GPM)

PRESSURE LOSS (PSIG)

103

0.00 1.26 2.52 3.79 5.05

FLOW RATES (l/s)

PRESSURE LOSS (kpa)

IS350XL 34-1 (REV. 4/13)

Performance Characteristics

Troubleshooting

PROBLEM

1. LEAKING CHECK VALVES

2. LOW OR NO FLOW

POSSIBLE CAUSES

1. Debris on seat or seal ring

2. Damaged seat

3. Damaged seal ring

4. Damaged check o-ring

1. Device installed backwards

2. Shut-off valves or valve upstream

may not be fully open

3. Low supply pressure

CORRECTIVE ACTION

1. Clean seat and seal ring area

2. Replace seat

3. Replace poppet

4. Replace check o-ring

FLOW CHARACTERISTICS

3/4" (20mm)

1" (25mm)

SPECIFICATIONS

Maximum working water pressure 175 PSI

Maximum working water temperature 180°F

Hydrostatic test pressure 350 PSI

End connections Threaded ANSI B1.20.1

Capacity thru Schedule 40 Pipe

Pipe size 5 ft/sec 7.5 ft/sec 10 ft/sec 15 ft/sec

1/8" 1 1 2 3

1/4" 2 2 3 5

3/8" 3 4 6 9

1/2" 5 7 9 14

3/4" 8 12 17 25

1" 13 20 27 40

1 1/4" 23 35 47 70

1 1/2" 32 48 63 95

2" 52 78 105 167

Proper performance is dependent upon licensed, qualied personnel performing regular, periodic testing according to ZURN

WILKINS’

specications and prevailing governmental & industry standards and codes and upon following these installation in-

structions. Failure to do so releases ZURN WILKINS of any liability that it might otherwise have with respect to that device. Such

failure could also result in an improperly functioning device.

Proposition 65 Warning This product contains chemicals known to the State of California to cause cancer or birth defects

or other reproductive harm.

Zurn-Wilkins 34-350XL, 1-350XL, 1-350XLFT Installation guide

Related papers

Other documents