JohnDow Industries JDI-27GFD Owner's manual
- Type
- Owner's manual
Height
Adjustment
Lock
27-Gallon
Portable Oil Drain
Model JDI-27GFD
Owner’s Manual
™
REV 8/21/17
For Service Assistance • Phone Toll Free 1-800-433-0708
Operation:
1. Operation
a. To raise or lower the funnel - loosen the funnel height
adjustment knob and move the drain tube up or down
to th desired height. (See Fig. 5)
b. Make sure the lower ball valve is closed before use.
C. Periodically check fluid level gauge to see the amount
of recovered oil that is in the tank. Never fill the tank
over the maximum level given by the level indicator.
(See Fig. 6)
Operating Instructions
Fig. 6
Fluid
Level
Gauge
Fig. 5
Assembly & Operating Instructions
Assembly Instructions
Fig. 2
Fig. 1
Fig. 3
Fig. 4
PLEASE READ THE ENTIRE OWNERS MANUAL
BEFORE USING THE DRAIN.
IMPORTANT!
This drain can only be emptied by gravity feed or using a waste evac system with a
diaphragm pump. Before using see section “To Empty The Drain” to make sure the drain
will work in your facility.
Checklist Of Components
Your portable oil drain was shipped with the following components. Please be sure you receive
them as listed below. Contact us if anything is missing.
Poly Drain Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
4” Caster Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1/4” x 3/4” Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
3/4” Washers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Fluid Level Gauge Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Drain Tube Assembly with Collar and Height Adjustment Tool . . . . . . . . . . . . . . . . . . . . . . . . .1
3/4” Ball Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Funnel
Height
Adjustment
Fluid Level
Gauge
Cap Wrench
and Tool
Pockets
To Assemble:
1. Funnel
a. Attach the funnel coupler to the threaded neck on the
funnel. (See Fig 1)
b. Insert the funnel into the swivel fitting on top of the
drain tube. (See Fig 2)
c. Tighten set-screw to secure funnel.
2. Caster Assembly
a. Attach the casters to the drain using the bolts and
washer provided. (See Fig. 3)
IMPORTANT!
Find the 3/4” ball valve on the bottom of the drain and make
sure it is in the closed position. The drain is now ready to
use. (See Fig. 4)
Assembly & Operating Instructions
Assembly Instructions
Fig. 2
Fig. 1
Fig. 3
Fig. 4
PLEASE READ THE ENTIRE OWNERS MANUAL
BEFORE USING THE DRAIN.
IMPORTANT!
This drain can only be emptied by gravity feed or using a waste evac system with a
diaphragm pump. Before using see section “To Empty The Drain” to make sure the drain
will work in your facility.
Checklist Of Components
Your portable oil drain was shipped with the following components. Please be sure you receive
them as listed below. Contact us if anything is missing.
Poly Drain Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
4” Caster Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1/4” x 3/4” Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
3/4” Washers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Fluid Level Gauge Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Drain Tube Assembly with Collar and Height Adjustment Tool . . . . . . . . . . . . . . . . . . . . . . . . .1
3/4” Ball Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Funnel
Height
Adjustment
Fluid Level
Gauge
Cap Wrench
and Tool
Pockets
To Assemble:
1. Funnel
a. Attach the funnel coupler to the threaded neck on the
funnel. (See Fig 1)
b. Insert the funnel into the swivel fitting on top of the
drain tube. (See Fig 2)
c. Tighten set-screw to secure funnel.
2. Caster Assembly
a. Attach the casters to the drain using the bolts and
washer provided. (See Fig. 3)
IMPORTANT!
Find the 3/4” ball valve on the bottom of the drain and make
sure it is in the closed position. The drain is now ready to
use. (See Fig. 4)
Height
Adjustment
Lock
27-Gallon
Portable Oil Drain
Model JDI-27GFD
Owner’s Manual
™
REV 8/21/17
For Service Assistance • Phone Toll Free 1-800-433-0708
Operation:
1. Operation
a. To raise or lower the funnel - loosen the funnel height
adjustment knob and move the drain tube up or down
to th desired height. (See Fig. 5)
b. Make sure the lower ball valve is closed before use.
C. Periodically check fluid level gauge to see the amount
of recovered oil that is in the tank. Never fill the tank
over the maximum level given by the level indicator.
(See Fig. 6)
Operating Instructions
Fig. 6
Fluid
Level
Gauge
Fig. 5
-
1
-
2
-
3
-
4
JohnDow Industries JDI-27GFD Owner's manual
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Ranger RD-20SE Owner's manual
-
Graco 333347F User manual
-
Gas and Go GG-30DC User manual
-
Sears 580751510 User manual
-
Liquidynamics 24176 User manual
-
Eastwood Scroll Compressor Oil Operating instructions
-
Ingersoll-Rand Marine Instruments 67384 User manual
-
Toro Roll-Over Protection System, Groundsmaster 72 User manual
-
Ransomes 67756 Owner's manual
-
Austin G YG Owner's manual
