DuraHook 990-S User manual

Type
User manual
Installation & Assembly Instructions
Please contact our Customer Service Division with any questions at:
30700 D Carter Street ∙ Solon, OH 44139 ∙ (P) 440.248.5480 ∙ support@tritonproducts.com
For a full line of products visit www.tritonproducts.com 1 INDH800
Read all instructions completely before installing. Should you have any questions about your installation, please call
Customer Service at 440-248-5480
Tools needed for this installation (not supplied with kit): Drill, Phillips Screw Driver, Tape Measure, Level
Parts Listing
Part Number Quantity Description
990 | 990-S 2 Polypropylene Pegboard 18” x 22” x 1/8” thick
24 Assortment DuraHook Locking Pegboard Hooks
32 Lock Screws for hooks (packaged separately)
2 Hanging Plastic Bins
2 BinClips for Hanging Plastic Bins
18 #12-2” long wood screws
18 #12 plastic wall anchors
18 Metal wall mounts/spacers
1. Wall Mounting Instructions: Polypropylene pegboards can be mounted to walls in separate locations, side by side
horizontally or above one another vertically.
A) Determine the location or locations where you want to mount your new storage system.
B) Determine if you want to mount boards (a) side by side horizontally, (b) above or below one another, or (c) in a
different location.
C) Using one sheet of the Polypropylene Pegboard (DuraBoard®) determine the location and height you wish to
mount your DuraHook storage system.
D) (Using diagram 1-1) Hold one sheet of pegboard flat against the wall surface, use level to make sure board is
level and square.
E) (Using diagram 1-1) While still holding pegboard flat against wall level and using a pencil, make a circular trace
inside of all (9) hole locations using diagram 1-1. (If planning to mount boards in totally separate locations go to
step (H)
F) If youre planning to mount the second pegboard directly to the side or above or below the first: Hold the first
pegboard flat against the wall while making sure all 9 traced holes are still aligned with appropriate holes in
pegboard. Using a pencil, trace the outer edge of the board you’re planning to mount the second board against.
G) If mounting side by side or above or below one another: use the second board in your kit, align outer edge with
pencil mark created in step (F). Do not cover up pencil mark with board. Mark hole locations as listed in step
(E).
H) Using an electric drill with 5/16" drill bit, drill hole locations marked in step (E). Should any hole location fall in
line with a wood wall stud, it will not be necessary to pre-drill.
990 | 990-S DuraHook Locking Pegboard System
Installation & Assembly Instructions
Please contact our Customer Service Division with any questions at:
30700 D Carter Street ∙ Solon, OH 44139 ∙ (P) 440.248.5480 ∙ support@tritonproducts.com
For a full line of products visit www.tritonproducts.com 2 INDH800
I) Gently insert plastic wall anchors into holes pre-drilled in step (H.) (You will not need to install plastic wall
anchors where a wall stud is located or when installing on solid wood surfaces. Wall anchors will be required for
all concrete walls.
J) Using your first pegboard sheet insert all nine (9) #12- 2" wood screws through the pegboard holes specified in
diagram 1-2.
K) Slip steel wall spacers over each screw as shown in diagram 1-3.
L) Insert each screw into its pre-installed wall anchor or assigned hole location. Using a #2 Phillips head
screwdriver and starting from one of the top corner hole locations insert screws halfway. (This will leave you
enough play/flexibility to insert each screw properly.)
M) Once all 9 screws have been installed halfway, tighten all screws down to a point that all spacers are snug
against wall surface. (Always avoid over-tightening of any screw.)
Repeat Instructions for installation of second pegboard panel
3. Hook Installation: (Using a hand held Phillips head screwdriver)
1. Insert hooks panel engaging tab through first hole in pegboard.
2. Align hooks screw hole with second hole in pegboard.
3. Secure in place using small Phillips head screws and hand held screwdriver (non-powered.) Do not use 2” long wood
screws. Do not over tighten screws used for mounting hooks.
Note: All hooks can be mounted horizontally or vertically to store items and can be combined with one another to
create storage solutions for heavier and odd shaped items and tools.
Diagram 1-2
Diagram 1-3
Installation & Assembly Instructions
Please contact our Customer Service Division with any questions at:
30700 D Carter Street ∙ Solon, OH 44139 ∙ (P) 440.248.5480 ∙ support@tritonproducts.com
For a full line of products visit www.tritonproducts.com 3 INDH800
Warranty information: Triton Products warrants to the original owner that this product is free from defects in material and
workmanship for a period of two years from the date of the original purchase. If this product is defective when used as
intended under normal household conditions within the specified period, Triton will replace the product, send a
replacement part or issue a refund (at our option) when the consumer provides a proof of purchase (either a bill of sale,
receipted invoice or other proof that the product is within the warranty period), along with a full description of the defect.
Liability: Triton Products and/or its Reseller’s liability are limited to 100% of the purchase price of the product.
  • Page 1 1
  • Page 2 2
  • Page 3 3

DuraHook 990-S User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI