Simplicity POWER RAKE, BILLY GOAT User manual

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 (B) 1 Form No F052215A

Patent 6253416 and other patents pending

POWER RAKE AND OVERSEEDER Owner's Manual

PR550, PR550H, OS552, OS552H

Accessories Replacement Parts

SLICING REEL

A complete verti-

slicing reel for your

PR. 20" wide reel for

use in grasses that

require vertical

cutting, and for

assisting in lawn

overseeding projects.

P/N 350414

OVERSEEDER KIT

The new light weight Plastic Overseeding

Kit is constructed of durable High Density

Polypropylene with two lift handles on

each side to assist in lifting the entire unit

and easily converts a PR Series Power

Rake into an overseeder with 4 bolts and

minimal tools.

NOTE: Overseeder Conversion Kit

(350328) includes Slicing Reel (350113).

Part No. (350325) comes with the

Overseeder Box only.

P/N 350325 / 350328

SLICING BLADES

A full set of blades for

replacement. Includes

new lock washers for

replacement

installation.

P/N 350187

FLAIL BLADES

A complete set of

our high quality flail

blades for your PR.

Includes new lock

clips for

replacement

installation.

P/N 350186

FLAIL SHAFTS

A full set of shafts

for replacement.

Includes new lock

clips for

replacement

installation.

P/N 350185

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

2

CONTENTS

SPECIFICATIONS AND SOUND/VIBRATION 3

INSTRUCTION LABELS 4

PACKING CHECKLIST & ASSEMBLY 5

OPERATION 6-8

MAINTENANCE 9-10

TROUBLESHOOTING 10

ILLUSTRATED PARTS LIST 11-16

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

3

SPECIFICATIONS

PR550 PR550H OS552 OS552H

Engine: HP

5.5 (4.1 kW)

Engine: Model

12H1320118B8

GX160T1QX2

12H1320118B8

GX160T1QX2

Engine: Type

B&S

VANGUARD

HONDA OHV

B&S

VANGUARD

HONDA OHV

Engine: Fuel Capacity

3.0 qt. (2.84 L)

3.88 qt. (3.6 L)

3.0 qt. (2.84 L)

3.88 qt. (3.6 L)

Engine: Oil Capacity

0.66 qt. (0.62 L)

0.69 qt. (0.65 L)

0.66 qt. (0.62 L)

0.69 qt. (0.65 L)

Total Unit Weight:

149# (67.7 kg)

147# (66.8 kg)

162# (73.6 kg)

160# (72.7 kg)

Engine weight:

36# (16.3 kg)

34# (15.4 kg)

36# (16.3 kg)

34# (15.4 kg)

Max. operating slope

15

o

20

o

15

o

15

o

Sound test in accordance

with 2000/14/EC

101 dB(a)

Sound at operators ear

82 dB(a)

Vibration at operator

position

0.82g (8.04 m/s

2

)

0.82g (8.04

m/s

2

)

3.2g

SOUND

SOUND LEVEL 82 dB(a) at Operators Position

Sound tests were conducted in accordance with 2000/14/EC, and were performed on 2-13-2002 under the conditions listed

below.

Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on the unit for

the sound power level for your model.

VIBRATION DATA

VIBRATION LEVEL .82g (8.04m/s

2

)

Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using calibrated

vibration test equipment. Tests were performed on 5-25-2006 under the conditions listed below.

General Conditions: Sunny

Temperature: 48

o

F (8.9

o

C)

Wind Speed: 2 mph (3.2 kmh)

Wind Direction: South East

Humidity: 29%

Barometric Pressure: 30.34Hg (770 mm Hg)

General Conditions: Sunny

Temperature: 72.32

o

F (22.4

o

C)

Wind Speed: 3.8 mph (6.12kph)

Wind Direction: East

Humidity: 62.2%

Barometric Pressure: 29.9Hg (101.3kpa)

101

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

4

INSTRUCTION LABELS

The labels shown below were installed on your BILLY GOAT

®

Power Rake/Overseeder. If any labels are damaged or missing,

replace them before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for

convenience in ordering replacement labels. The correct position for each label may be determined by referring to the Figure and

Item numbers shown.

LABEL DANGER KEEP HANDS LABEL CLUTCH ITEM #49 DANGER FLYING DEBRIS LABEL SPARK ARREST

AND FEET AWAY P/N 830503 ITEM # 48 P/N 810736 ITEM #81 100252

ITEM #51 P/N 400424

LABEL CAUTION GUARDS LABEL EXPLOSIVE FUEL LABEL INSTRUCTION HEIGHT ADJ.

ITEM #52 P/N 900327 ITEM # 50 P/N 400268 ITEM #35 P/N 350176

LABEL INSTRUCTIONS SEEDER BOX LABEL SEED METERING

ITEM #30 P/N 350386 ITEM #29 P/N 350392

(page 8) (page 8)

ENGINE LABELS

ENGINE CONTROLS

Honda Briggs & Stratton Set lever to choke when starting cold

Throttle lever

Set lever to desired engine speed.

Fuel valve Choke lever Move lever completely to the left to

stop engine

BRIGGS & STRATTON HONDA

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

5

PACKING CHECKLIST

NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts Lists on pages 11-16.

Your Billy Goat Power Rake is shipped from the factory in one carton, completely assembled.

PUT OIL IN ENGINE BEFORE STARTING

ASSEMBLY

READ all safety instructions before assembling unit.

TAKE CAUTION when removing the unit from the box, the Handle Assembly is attached to the unit by

cables.

NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts lists on pages 11-16.

1. UNFOLD the upper handle (item 26) and slide handle lock loops (item 28) into place to secure the upper handle to the

lower.

2. CHECK engine oil level and fill to proper level with engine manufacturers recommended grade of oil. Move height adjust

lever to down position, to level engine during checking. See engine manufacturer’s instruction manual.

3. CONNECT spark plug wire.

Boxing Parts Checklist

Briggs & Stratton

5.5 B&S VANGUARD

Honda 5.5 OHV

Subaru 6HP EX17

Literature Assy

P/N-350110

PARTS BAG & LITERATURE ASSY

Warranty card P/N- 400972, Owner’s Manual P/N-350412, General Safety and Warnings Manual P/N-100295, Declaration of

Conformity P/N-350139.

PR550, PR550H,

PR550T, PR550HT,

PR600S

OS552, OS552H,

and OS602S

28

26

28

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

6

OPERATION

NOTE: Items in ( ) can be referenced in the Parts Illustration and Parts list on pages 11-16.

SLICING OPERATION

NOTE: NEVER PARK THIS UNIT ON A SLOPE OF ANY KIND. Always keep the reel in

the up position when parking the unit.

BLADE POSITION & DEPTH CONTROL LEVER: The blades can be raised or lowered into the

ground by height adjustment lever on the engine base. The height adjuster lock lever must be

pushed back against the adjustment lever in order to lower the blades into the ground. The

resulting blade depth can be adjusted higher or lower.

ADJUSTING BLADE DEPTH: The blades can be raised or lowered by rotating the knob on the

top of the adjustment lever. The blades are lowered by rotating the knob clockwise, and raised

by rotating the knob counter-clockwise. The relative depth of the blades can be gauged by using

the depth scale located on the right front corner of the engine base. With new blades installed

the depth can be estimated as follows: 2.5 on the scale is even with the ground, 3 is equal to

0.25" deep, and 3.5 is equal to 0.5" deep.

FOLDING HANDLE: This unit is equipped with a folding upper handle for easier storage and

transportation. The handle can be folded by sliding the handle lock loops (item 28) up. This

releases the upper handle, allowing it to be folded over the unit.

RAKING OPERATION-FLAIL REEL (See Fig. 4)

NOTE: Must have the flail reel assembly (350112) for this operation.

SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat surface (i.e.

driveway, or sidewalk).

ENGAGE BLADES: Pull back on the bail on the operators handle. NOTE: When engaging the blades

in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators handle

lifting the front wheels slightly. Engage the blades. Slowly lower the unit into the turf.

RAKE: Rake a small test area and examine the results. Thatch should be removed and deposited on

top of the healthy grass. If excessive damage occurs to healthy grass, adjust the blade depth to

decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west).

NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during

operation the blade depth is set too low.

REMOVE THATCH: After raking, a layer of thatch will be deposited over the top of the lawn. This

thatch must be removed prior to any fertilizing, seeding, or watering of the lawn. We suggest the use

of a lawn vacuum or wheeled blower for collection and removal of the thatch.

clockwise to

lower blades

counter clockwise

to raise blades

blades up

transport

blades up

transport

blades down

running

Fig. 1

Fig. 2

SPRING TINE CONVERSION

If you are converting your Power Rake to a spring tine reel, you will

need to replace the spacer on the control lever to accommodate for

the tine. First remove the clip (item 18), then unscrew the yoke (item

17), remove the washer (items 69) and insert the spacer (item 75) in

front of the spring. Reassemble in reverse order.

Fig. 3

Fig. 4

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

7

RAKING OPERATION-SPRING REEL (See Fig. 5)

NOTE: Must have the spring tine reel assembly (350354) for this operation.

SET DEPTH: With engine off, set the raking depth so that the spring tines are just above touching the

flat surface (i.e. driveway, or sidewalk) the units height is being adjusted on. NOTE: Allowing the

spring tines to have substantial contact with the ground will cause premature wear and failure of the

spring tines.

ENGAGE TINES: Pull back on the bail on the operators handle. NOTE: When engaging the spring

tines in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators

handle lifting the front wheels slightly. Engage the spring tines. Slowly lower the unit into the turf.

RAKE: Rake a small test area and examine the results. Thatch should be removed and deposited on

top of the healthy grass. If excessive damage occurs to healthy grass, adjust the spring tine depth to

decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west).

NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during

operation the spring tine depth is set too low.

REMOVE THATCH: After raking, a layer of thatch will be deposited over the top of the lawn. This

thatch must be removed prior to any fertilizing, seeding, or watering of the lawn. We suggest the use

of a lawn vacuum or wheeled blower for collection and removal of the thatch.

VERTI-CUTTING OPERATION (See Fig. 6)

NOTE: Must have the slicing reel assembly (350113) for this operation.

SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat surface

(i.e. driveway, or sidewalk).

ENGAGE BLADES: Pull back on the bail on the operators handle. NOTE: When engaging the

blades in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the

operators handle lifting the front wheels slightly. Engage the blades. Slowly lower the unit into the

turf.

SLICE: Verti-cut a small test area and examine the results. Some thatch and cut stems should be

removed and deposited on top of the healthy grass. Grass runners should be cut and ready for

removal. If excessive damage occurs to healthy grass, adjust the blade depth to decrease

damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west). NOTE:

If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during operation

the blade depth is set too low.

REMOVE THATCH/STEMS: After verti-cutting, a layer of thatch and cut stems will be deposited

over the top of the lawn. We suggest the use of a lawn vacuum or wheeled blower for collection

and removal of the thatch/stems.

OVERSEEDING OPERATION

NOTE: Must have the slicing reel assembly (350113) for this operation.

DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.

SEED: Spread grass seed according to the seed suppliers directions (e.g. 10 lbs. per 1000 ft

2

[4.5 kg. per 93 m

2

])

SET DEPTH: With engine off, set the raking depth so that the blades reach 1/4"-1/2"(6-12 mm) below a flat surface (i.e. driveway,

or sidewalk).

ENGAGE CLUTCH: Pull back on the bail on the operators handle. NOTE: When engaging the clutch in heavy load conditions (i.e.

heavy thatch, or very uneven turf), push down on the operators handle lifting the front wheels slightly. Engage the clutch. Slowly

lower the unit into the turf.

SLICE: Run machine over the area that has been seeded to incorporate the seed into the soil. If excessive damage occurs to

healthy grass, adjust the blade depth to decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or

east-west). NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during operation the blade

depth is set too low.

WATER/FERTILIZE: After the seed has been worked into the soil, water and fertilize according to the seed suppliers directions.

Fig. 5

Fig. 6

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

8

ADJUSTING SEED RATE

LAWN PREPARATION

 Mow lawn to lowest setting on your mower.

 Do not water prior to seeding.

 Power rake to dethatch lawn and remove thatch.

 Fertilize lawn with broadcast spreader.

 For best results overseed in two passes of one-half application

rate each, at right angles or in a criss-cross pattern. (See Fig 7 &

8)

 Water heavily immediately then lightly for 10 - 14 days, keeping

soil moist.

 After germination, water less often to promote root growth.

*****TIPS*****

Before beginning, it is best to evaluate the condition of the lawn by cutting one or more core samples from area to be treated. A core can

be cut using a piece of PVC, or metal pipe. Hammer the pipe into the ground, remove it, push the core out of the pipe and inspect it to

determine the depth of thatch in your yard.

MOW

Mow the lawn to its normal cut height. Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.

INSPECT

Check the lawn before beginning work. Remove all rocks, wire, string, or other objects that can present a hazard during work

IDENTIFY

Mark all fixed objects to be avoided during work, such as sprinkler heads, water valves, buried cables, or clothes line anchors, etc.

THATCH

Thatch is a dense layer of dead grass, clippings, and roots that builds up over time at the base of the lawn preventing air, water, and

fertilizer from reaching the soil. This can cause shallow root development and make a lawn more susceptible to drought and disease.

Thatch also provides an ideal environment for insects to hide and multiply. Periodic removal of thatch will keep your lawn in good health.

HEAVY THATCH

Lawns with an excessive amount of thatch will require multiple treatments for effective removal. Trying to remove excessive thatch

(greater than 3/4"[19 mm] deep) in one treatment will damage or destroy the living part of the lawn. It is best to remove heavy thatch in

seasonal treatments (i.e. spring, and fall).

SLOPES

Rake slopes across not up and down the slope. This is much easier and safer for the operator and is better for the lawn. Raking across

will help to reduce runoff during watering and allow the sloped ground to hold more seed, fertilizer, and water. The units maximum

operating slope is 35% or 19°.

DEPTH

The wide range of depth adjustment on your unit is provided to allow for blade wear. Setting the reel deeper will not produce better

results. The flail reel is intended to be set so it just touches the surface on flat ground. The slicing reel should be set even with the ground

for verti-slicing work, and set to a maximum 1/2" depth for overseeding. Setting the reel deeper will only result in premature wear on the

unit (i.e. failed belt). If you desire to work the ground deeper than the above guidelines, it should be done gradually in multiple passes.

SLICING / OVERSEEDING: Mow the lawn to shorter than the normal cut height before starting (i.e. approximately 2" tall for fescue grass).

For the best result, Slice/Overseed in criss-cross pattern (See Fig. 7 & 8).

Fig. 7

Fig. 8

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

9

MAINTENANCE

NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts Lists on pages 11-16.

PERIODIC MAINTENANCE

Periodic maintenance should be performed at the following intervals:

Maintenance Operation

Every Use (daily)

Every 25 Hours

Inspect for loose, worn or damaged parts



Check engine oil



Inspect belt



Engine (See Engine Manual)

Grease reel bearings



Inspect and clean engine air filter



Oil height adjustment linkage



FLAIL BLADE WEAR

1. Wait for engine to cool and disconnect spark plug.

2. Close fuel valve on engine (if available).

3. Lean unit back onto lower handles and secure in place.

4. Inspect blades for wear, and immediately replace any bent or cracked blades.

Measure the overall length of the blade. (See Fig. 9)

5. If blades measure less than 3.25"(83 mm) in overall length they must be

replaced. NOTE: We recommend replacing all the flails at once.

SLICING BLADE WEAR

1. Wait for engine to cool and disconnect spark plug.

2. Close fuel valve on engine (if available).

3. Lean unit back onto lower handles and secure in place.

4. Inspect blades for wear, and immediately replace any bent or cracked blades. Measure the overall length of the blade

from the center of the attachment bolt to the tip of the worn blade.

5. If blades measure less than 3"(76 mm) in length they must be replaced. NOTE: We recommend replacing all the blades

at once.

ROTATING FLAIL REEL END TO END

To maximize flail blade life and performance the reel can be rotated end to end periodically to provide a fresh lead cutting edge.

Takes approx. 20 min. and requires 1/2" and 9/16" socket wrenches with extension bar.

1. Wait for engine to cool and disconnect spark plug.

2. Close fuel valve on engine (if available).

3. Lean unit back onto lower handles and secure in place.

4. Remove seven lock nuts (item 62 & 40) holding the belt and shaft guards (item 21 & 22) in place. It is necessary to lower

the height adjust lever to reach the locknuts on the guards. Remove the guards.

5. Remove the drive belt (item 9) by "walking" it out of the groove on the reel pulley (item 2).

6. Remove the four lock nuts (item 60) and washers (item 68) holding the bearings (item 23) to the frame of the unit.

7. The reel is now free from the machine. Slide the reel down and out of the machine.

8. Remove the capscrew (item 71), lock washer (item 57), reel pulley (item 2), key (item 42), and reel spacer (item 10) from

the end of the reel.

9. Rotate the reel end to end, and re-install these items on the opposite end of the reel.

10. Re-install the reel in reverse order of removal. Re-install the guards in reverse order of removal.

Fig. 9

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

10

TROUBLESHOOTING

DRIVE BELT REPLACEMENT

NOTE: Takes approx. 10 min. and requires 1/2" socket wrench with extension.

1. Wait for engine to cool and disconnect spark plug.

2. Remove four lock nuts (item 62) holding the belt guard (item 21) in place. It is necessary to lower the height adjust lever to

reach the locknuts on the guard. Remove the guard.

3. Remove the belt (item 9) by rotating the reel pulley (item 2) and walking it out of the groove. Discard the old belt.

4. Install new belt using same procedure to walk the belt into the groove.

5. With new belt installed pull bail rod back to engaged position and measure extension of idler spring. Spring should stretch

3/4" - 1" (19 25 mm) with bail engaged. Adjust clutch cable as necessary to achieve this extension.

6. Re-install the belt guard.

Problem Possible Cause Solution

Abnormal vibration

Damaged or missing blades. Loose

handle bolts. Loose engine bolts.

Stop work immediately. Replace any

damaged or missing blades. Tighten

all loose nuts and bolts.

Engine stalls or labors

when raking

Blades set too deep into ground.

Raise blades so that they just touch

the ground on a level surface.

Engine will not start

Stop switch off (Honda only). Throttle

in off position.

Check choke position.

Out of gasoline or bad, old gasoline. Check gasoline.

Spark Plug wire disconnected. Connect spark plug wire.

Gas valve off. Turn on gas valve.

Dirty air cleaner.

Clean or replace air cleaner. Contact

a qualified service person.

Engine is locked, will not

pull over

Debris locked against reel, or drive

pulleys. Engine problem.

Pull spark plug wire and remove

debris. Contact an engine servicing

dealer for engine problems.

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

11

POWER RAKE SEEDER BOX KIT P/N 350395

PARTS LIST

ITEM NO. PART NO. DESCRIPTION QTY

1 350366 BOX AND LID ASSEMBLY 1

2 350390 BRACKET CABLE MOUNTING 1

3 350385 CABLE SEED METERING ASSY 1

4 350378 SHAFT PLASTIC DROP SEEDER 1

5 350271 PLATE DOOR DROP SEEDER 1

6 350272 PLATE DOOR DROP SEEDER END 1

7 350387 PLATE DOOR DROP SEEDER END ARM 1

9 350370 PULLEY 3V GROOVE 0.625" BORE 1

10 8172009 WASHER #10 3/8 SAE 1

11 900321 BEARING CLIP 1.375 OD 4

12 890108 KNOB WING 5/16-18 1

13 400217 SPRING TENSION 2

14 8024040 BOLT CARRIAGE 5/16 - 18 X 1 1

15 8024021 BOLT CARRIAGE 1/4-20 X 3/4" 1

16 8123087 SCREW SELF TAP #10-24 X 3/8" HMS ZP 4

17 8160001 NUT LOCK 1/4 1

18 350389 BRACKET CABLE SEEDER BOX 1

19 8160002 NUT LOCK 5/16 1

20 8177011 WASHER LOCK 5/16 4

21 350369 PULLEY 3V GROOVE 1.530" BORE 1

22 350280 WASHER 0.906 O.D. X 0.656 I.D. X 0.062 7-8

ITEM NO. PART NO. DESCRIPTION QTY

23 8041026 SCREWCAP 5/16-18 x 3/4 4

24 350372 BELT O-RING 5/16 X 15 9/16" 1

25 8197031 PIN COTTER 1/8" X 1" 1

26 9195106 ROLL PIN 1/8 - 1 1/4 1

27 8172020 WASHER 5/16 FENDER 4

28 8172007 WASHER 1/4 SAE 3

29 350392 LABEL SEED METERING 1

30 350386 LABEL DROP SEEDER BOX 1

31 900230 WASHER 1/2 FC 2

32 8161044 NUT LOCK 1/2" THIN HGT 1

33 890456 LABEL HOSE PLUG KD/SV 1

34 350423 LABEL OS BADGING 1

35 8024061 CARRIAGE BOLT 3/8-16 X 1 3/4" 1

36 8024025 CARRIAGE BOLT 1/4-20 X 1 3/4" 1

37 350399 PIN CLEVIS .25 X .61 1

38 900471 PIN HAIR 1/4 ZP 1

39 8160003 NUT LOCK 3/8-16 HEX 1

40 8171004 WASHER 3/8 FC 2

41 350391 BRACKET MOUNTING METERING SEED 1

42 8059135 SCREW MACHINE #10-24 X 5/8 1

43 8164005 NUT LOCK LT #10-24 HEX 1

44 900407 TY-WRAP 1

32

31

21

24

30

23

20

9

22

11

6

33

1

17

5

28

27

34

16

13

4

26

43

17

28

40

39

19

42

12

10

29

41

36

14

3

44

15

28

35

25

38

11

7

22

37

2

18

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

12

FLAIL SHAFT KIT 350185

FLAIL BLADE KIT 350186

SPACER BUMPER KIT 350258

SLICING BLADE KIT 350187

FLAIL REEL KIT P/N 350112

item

PARTS

Part No. QTY

no. LIST

73 SHAFT FLAIL BLADE 350141 4

78 CLIP LOCK 1/2" 350146 8

item

PARTS

Part No. QTY

no. LIST

74 BLADE FLAIL 350100 30

78 CLIP LOCK 1/2" 350146 8

item

PARTS

QTY

no. LIST

Part No.

57 LOCK WASHER 3/8 S/T MED

8177012 1

68 WASHER 3/8 FLAT CUT

8171004 1

71 SCREWCAP REEL PULLEY

8041050 1

73 SHAFT FLAIL BLADE 350141 4

74 BLADE FLAIL 350100 30

76 SPACER BUMPER 5/8" x 1/2" 350144 54

77 SHAFT WA FLAIL REEL 350145 1

78 CLIP LOCK 1/2" 350146 8

79 WASHER 1/2 SAE 8172011 8

item

PARTS LIST

QTY

no.

Part No.

81 BLADE 10" HEX SLICING 350147 20

85 SCREWCAP 1/4-20 X 3/4 GR 8 350427 40

86 NUT LOCK 1/4-20 8142004 40

item

PARTS

QTY

no.

LIST

76 SPACER BUMPER 5/8" x 1/2" 350144 54

Part No.

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

13

SPRING TINE REEL ASSY - 350355-S

SPRING REPLACEMENT KIT - 350356-S

SLICING REEL ASSY P/N 350414

82

83

85

84

83

82

81

80

item

PARTS

QTY

no.

LIST

80 SHAFT SLICING WA 350416 1

81 BLADE SLICING WA 350147 20

82 SCREWCAP 1/4"-20 X 3/4 GR 8 8041004 40

83 NUT LOCK 1/4" - 20 2 WAY 8142004 40

84 WASHER LOCK 3/8" S/T MED 8177011 1

85 SCREWCAP 3/8"- 16 X 1" HCS ZP 400389 1

Part No.

item PARTS QTY

no. LIST

1 SHAFT WA SPRING TINE REEL 350353 1

2 SHAFT SPRING TINE REEL 350351 4

3 SPRING TINE 350352 108

4 RING RETAINING 1/2" 350146 8

5 SCREWCAP3/8"-16 X 1" HCS ZP 8041050 1

6 WASHER LOCK 3/8 S/T MED 8177012 1

68 WASHER 3/8 FLAT CUT 8171004 1

Part No.

item

PARTS

no.

LIST

3 SPRING TINE 350352 108

4 RING RETAINING 1/2" 350146 8

Part No.

QTY

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

14

PARTS DRAWING PR/OS

PR550, PR550H, OS552, OS552H

SEE PAGE 13 FOR SPRING REEL PARTS LIST

SEE PAGE 13 FOR SLICING REEL PARTS LIST

SEE PAGE 12 FOR FLAIL REEL PARTS LIST

FOR PARTS LIST

SEE PAGE 11

THE OS MODELS ONLY

ASSY. FOR

LEFT FRONT WHEEL

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

15

PARTS LIST PR/OS

Item

PARTS

PR550 QTY PR550H QTY OS552 QTY OS552H QTY

no. LIST Part No. Part No. Part No. Part No.

1 Pulley 3" OD 350101 1 350101 1 350101 1 350101 1

1A Spacer 5/8 OD X 3/8 ID X 1.0 LG 350401 3 350401 3 350401 3 350401 3

2 Pulley 6.5" OD X ¾" 350102 1 350102 1 350102 1 350102 1

3 WHEEL 8.0" X 5/8" BEARING 350103 2 350103 2 350103 2 350103 2

4 WHEEL 10.0" X 5/8" BEARING 350104 2 350104 2 350104 2 350104 2

5 Height Adjust Assy 350107 1 350107 1 350107 1 350107 1

6 Reel Flail / Slicing / Spring Assy 350112 1 350112 1 350414 1 350414 1

7 Pulley Idler 2.75" 350114 1 350114 1 350114 1 350114 1

8 Arm Idler WA 350115 1 350115 1 350115 1 350115 1

9 Belt 5L X 36 350116 1 350116 1 350116 1 350116 1

10 Screwcap 5/16" x 24 x 1 1/2 Gr5 HCS 8042030 3 8042030 3 8042030 3 8042030 3

11 Bracket Mount Clutch Cable 350119 1 350119 1 350119 1 350119 1

12 Chassis WA W/ Label 350194 1 350194 1 350194 1 350194 1

13 Frame Front WA 350121 1 350121 1 350121 1 350121 1

14 Bushing 0.375 OD X 0.256 ID X 0.88 350309 1 350309 1 350309 1 350309 1

15 Spring Height Adjust PR500 350125 1 350125 1 350125 1 350125 1

16 Link Height Adjust PR500 350126 1 350126 1 350126 1 350126 1

17 Yoke ½ - 20 350127 1 350127 1 350127 1 350127 1

18 Pin Yoke ½" 350128 1 350128 1 350128 1 350128 1

19 Bracket Mount Hgt. Adj. WA 350182 1 350182 1 350182 1 350182 1

20 Spacer Spanner Wheel PR500 350130 4 350130 4 350130 4 350130 4

21 Guard Belt WA W/ Label 350384 1 350384 1 350384 1 350384 1

22 Guard Shaft WA W/ Label 350196 1 350196 1 350196 1 350196 1

23 Bearing ¾" Cast Pillow Block 350133 2 350133 2 350133 2 350133 2

24 Handle Lower LH WA 350134 1 350134 1 350134 1 350134 1

25 Handle Lower RH WA 350135 1 350135 1 350135 1 350135 1

26 Handle Upper PR500 350375 1 350375 1 350375 1 350375 1

27 Bail Clutch WA 350374 1 350374 1 350374 1 350374 1

28 Loop Folding Handle 350138 2 350138 2 350138 2 350138 2

29 Deflector Rubber 350167 1 350167 1 350167 1 350167 1

30 Shield Bearing 350168 2 350168 2 350168 2 350168 2

31 Bar Clamp Deflector 350171 1 350171 1 350171 1 350171 1

32 Bracket Height Adjust Lock WA 350173 1 350173 1 350173 1 350173 1

33 Guard Pulley Back 350400 1 350400 1 350400 1 350400 1

34 Lever Height Control 350175 1 350175 1 350175 1 350175 1

35 Label Instr. Hgt. Adj. 350176 1 350176 1 350176 1 350176 1

36 Bolt Shoulder ¼" x 1 ¾" 350178 1 350178 1 350178 1 350178 1

37 Bolt Shoulder 5/16" x 1 ¾" 350179 1 350179 1 350179 1 350179 1

38 Cable Clutch PR 350408-S 1 350408-S 1 350408-S 1 350408-S 1

39 Bushing Caster Yoke Spacer 520034 3 520034 3 520034 3 520034 3

40 BOLT SHOULDER 1/2" X 1" 500114 1 500114 1 500114 1 500114 1

41 ENGINE HONDA 5.5 H.P. GX160 - - 600115 1 - - 600115 1

ENGINE 5.5 HP B&S VANGUARD 350379 1 - - 350379 1 - -

42 KEY 3/16" X 1" 9201078 2 9201078 2 9201078 2 9201078 2

43 GRIP 1" x 13" 400570 2 400570 2 400570 2 400570 2

44 GRIP LEVER 1/8 x 1 x 5" 500181 1 500181 1 500181 1 500181 1

45 LABEL INSTRUCTION SEEDER BOX - - - - 350288 1 350288 1

46 LABEL PR BADGING 350422 1 350422 1 350422 1 350422 1

47 FINGER BELT WIRE 350301 1 350301 1 350301 1 350301 1

48 LABEL DANGER THROWN OBJECT 810736 1 810736 1 810736 1 810736 1

49 LABEL CLUTCH VQ 830503 1 830503 1 830503 1 830503 1

50 LABEL WARNING FUEL EN/SP 100261 1 - - 100261 1 - -

51 LABEL WARNING 400424 2 400424 2 400424 2 400424 2

52 LABEL DANGER GUARD 900327 1 900327 1 900327 1 900327 1

53 PLUG CAP 1" RD 890132 2 890132 2 890132 2 890132 2

54 BOLT CARRAIGE 3/8-16 x 1 3/4 8024061 4 8024061 4 8024061 4 8024061 4

55 BOLT CARRAIGE 5/16-18 x 1 3/4 8024043 2 8024043 2 8024043 2 8024043 2

56 BOLT CARRIAGE 5/16 -18 x 3/4 8024039 4 8024039 4 8024039 5 8024039 5

57 WASHER LOCK 3/8" S/T MED 8177012 1 8177012 1 - - - -

WASHER LOCK 5/16" TW TOOTH - - - - 430298 1 430298 1

58 NUT LOCK #10-24 8164005 1 8164005 1 8164005 1 8164005 1

59 NUT LOCK 1/4-20 8160001 2 8160001 2 8160001 5 8160001 5

60 NUT LOCK 3/8-16 8160003 12 8160003 12 8160003 12 8160003 12

62 NUT LOCK 5/16-18 8160002 15 8160002 15 8160002 16 8160002 16

63 SCREWCAP 1/4-20 x 1 1/2 8041008 1 8041008 1 8041008 1 8041008 1

64 SCREWCAP 3/8 - 16 x 1 3/4 8041053 1 8041053 1 8041053 1 8041053 1

Not for Reproduction

OVERSEEDER/POWER RAKE Owner’s Manual

Part No 350412 Form No F052215A

16

Item

PARTS

PR550

QTY

PR550H

QTY

OS552

QTY

OS552H

QTY

no.

LIST

Part No. Part No. Part No. Part No.

65 SCREWCAP 5/16-24 x 3/4" GR.5 8042026 1 8042026 1 8042026 1 8042026 1

65A Washer 3/4 SAE 8172015 2 8172015 2 8172015 2 8172015 2

65B Washer 5/16 Twist Tooth 430298 1 430298 1 430298 1 430298 1

66 SCREWCAP 5/16 - 18 x 1 1/2 8041030 4 8041030 4 8041030 4 8041030 4

68 W ASHER 3/8 FLAT CUT 8171004 9 8171004 9 8171004 8 8171004 8

69 W ASHER 1/2 SAE ZP 8172011 2 8172011 2 8172011 5 8172011 5

70 NUT LOCK 1/2" - 13 THIN HGT 8161044 4 8161044 4 8161044 4 8161044 4

71 SCREWCAP 3/8" - 16 X1" HCS ZP 8041050 1 8041050 1 8041050 1 8041050 1

72 BUTTON SOCKET 5/16-18X5/8” 350266 4 350266 4 - - - -

73 BOLT SHOULDER 1/2" x 2" 520031 2 520031 2 520031 2 520031 2

74 FLANGE SCREW 0.375 -16 X 0.75 791080 2 791080 2 791080 2 791080 2

76 WASHER 3/8 SAE 8172009 2 8172009 2 8172009 2 8172009 2

77 NUT PAL 3/8 360218 2 360218 2 360218 2 360218 2

78 WASHER 1/4 FLAT CUT 8171002 5 8171002 5 8171002 5 8171002 5

79 PIN CLEVIS 3/8" X 1.625 520119 2 520119 2 520119 2 520119 2

80 RETAINER 3/8" BOLT PUSH NUT 360279 2 360279 2 360279 2 360279 2

81 LABEL SPARK ARRESTOR EN/SP - - 100256 1 - - 100256 1

82 WASHER 1/4 SAE 8172007 1 8172007 1 8172007 1 8172007 1

83 LABEL LOGO PRODUCT SM CIRCLE 890456 1 890456 1 890456 1 890456 1

90 WASHER 1.125" OD X .344 ID X .25 THK - - - - 441150 1 441150 1

100 WASHER FLAT 5/16" 8171003 5 8171003 5 8171003 5 8171003 5

101 SCREW MACH #10-24 X 5/8" HWF ZP 8059135 1 8059135 1 8059135 1 8059135 1

102 NUT LOCK #10-24 HEX 8164005 1 8164005 1 8164005 1 8164005 1

104 LABEL MADE IN U.S.A. 520116 1 520116 1 520116 1 520116 1

Not for Reproduction

Simplicity POWER RAKE, BILLY GOAT User manual

This manual is also suitable for

Simplicity POWER RAKE, BILLY GOAT User manual

Related papers

Other documents