Miller KB000000 Owner's manual

Miller
Brand
Miller
Model
KB000000
Type
Owner's manual

This manual is also suitable for

Miller KB000000 Running Gear is a robust and versatile piece of equipment designed to provide a stable and mobile platform for your power source and welding tools. With its sturdy construction and convenient features, the Running Gear ensures efficient and safe operation in various welding applications.

The Running Gear boasts a durable bottom pan that securely accommodates your power source, preventing it from shifting or falling during transportation. Its heavy-duty axle and wheels provide excellent stability and support, allowing you to maneuver the unit smoothly even on uneven surfaces. The included casters enable effortless mobility, making it easy to position the Running Gear precisely where you need it.

Miller KB000000 Running Gear is a robust and versatile piece of equipment designed to provide a stable and mobile platform for your power source and welding tools. With its sturdy construction and convenient features, the Running Gear ensures efficient and safe operation in various welding applications.

The Running Gear boasts a durable bottom pan that securely accommodates your power source, preventing it from shifting or falling during transportation. Its heavy-duty axle and wheels provide excellent stability and support, allowing you to maneuver the unit smoothly even on uneven surfaces. The included casters enable effortless mobility, making it easy to position the Running Gear precisely where you need it.

OWNER’S MANUAL
OM-633 196 597B
May 2001
Running Gear No. 30 (195 443)
WARNING
ELECTRIC SHOCK can kill.
• Do not touch live electrical parts.
• Turn Off power source and input disconnect device.
• Disconnect input plug or power conductors from
deenergized supply BEFORE moving power
source.
FALLING EQUIPMENT can cause injury
and damage.
• Properly install and secure power source into holes
provided on cart.
• Always secure or remove any tools stored on cart
before moving unit.
• Cart is only designed to handle weight of power
source, cables, torch, and a few simple tools – do not
overload cart with any additional weight.
Ref. 802 469-A
Tools Needed:
Description (Qty)
Item
No.
1 Bracket RH (1)
2 Screw, 8 mm x 1 x 20 mm (4)
3 Pan, Bottom (1)
4 Bracket LH (1)
5 Label, Warning (2)
6 Nut, 10 mm x 1.5 (2)
7 Bracket, mtg casters (1)
8 Caster, 2 in (2)
9 Cotter Pin (2)
10 Wheel, 8 in (2)
11 Washer, 13 mm ID flat (4)
12 Axle (1)
13 Nut, 8 mm (4)
Be sure to provide Model when ordering
replacement parts.
Go to Figure 2 for cord wrap installation
procedures.
. Both rear bolts must be
installed in bottom pan
before installing axle to
running gear.
1
2
3
4
5
6
7
8
9
10
11
12
13
10 mm, 12 mm
10 mm, 13 mm
. Be sure that recessed
opening on hub is to
the outside on axle to
allow installation of
washer and cotter pin.
11
Figure 1. Running Gear Assembly
OM-633 Page 2
Ref. 802 469-A
16
15
16
14
19
20
21
. Cord wrap can be installed to
either left or right side of
running gear.
14 Support Bracket (1)
15 Cord Wrap (1)
16 Screw, M6 x 1 x 12 mm (6)
17 Screw, M6 x 1 x 12 mm (4)
18 Nut, M6 x 1 hex (4)
Install support bracket to running
gear and hold in place using screws
in side without cord wrap. Do not
tighten hardware.
Install cord wrap and hold in place
using supplied screws. Upper
screws must also hold support
bracket. Tighten all hardware.
19 Hole (2)
Remove side panel screws from left
and right side of power source that
align with holes in brackets.
20 Slot (2)
Loosen side panel screws on left
and right side of power source that
align with slots in brackets.
21 Pad (4)
Place power source on running
gear pads and lower loosened side
panel screws into slots in brackets.
Reinstall screws through holes in
brackets and back into side panels.
Tighten side panel screws to
secure power source to running
gear.
Optional Small Unit Bracket
Installation:
If installing a smaller unit on the run-
ning gear, proceed as follows:
22 Adapter Bracket LH (1)
23 Adapter Bracket RH (1)
Install adapter brackets (22 and 23)
to unit using left and right side
wrapper screws that align with
bracket inner mounting flanges.
Install screw (17) and nut (18) into
left and right rear holes of outer
flange on mounting brackets. Do
not tighten hardware.
Install unit with brackets onto cart
so that loose hardware in rear
bracket holes slides down into cart
slots (20). Install screw (17) and nut
(18) into left and right front holes of
outer flange on mounting brackets.
Tighten both front and rear
hardware in mounting brackets to
secure unit to cart.
21
22
23
18
17
Optional Small Unit
Bracket Installation
Figure 2. Installing Cord Wrap
  • Page 1 1
  • Page 2 2

Miller KB000000 Owner's manual

Miller
Brand
Miller
Model
KB000000
Type
Owner's manual
This manual is also suitable for

Miller KB000000 Running Gear is a robust and versatile piece of equipment designed to provide a stable and mobile platform for your power source and welding tools. With its sturdy construction and convenient features, the Running Gear ensures efficient and safe operation in various welding applications.

The Running Gear boasts a durable bottom pan that securely accommodates your power source, preventing it from shifting or falling during transportation. Its heavy-duty axle and wheels provide excellent stability and support, allowing you to maneuver the unit smoothly even on uneven surfaces. The included casters enable effortless mobility, making it easy to position the Running Gear precisely where you need it.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents