Brother Innov-is BQ1350 User manual

Operation Manual

Sewing Machine

Product Code: 888-F50/F52/F60/F62/F70/F72

Be sure to read this document before using the machine.

We recommend that you keep this document nearby for future reference.

INTRODUCTION

i

Thank you for purchasing this machine. Before using this machine, carefully read the “IMPORTANT SAFETY

INSTRUCTIONS”, and then study this manual for the correct operation of the various functions.

In addition, after you have finished reading this manual, store it where it can quickly be accessed for future reference.

Please read these safety instructions before attempting to use the machine.

DANGER - To reduce the risk of electrical shock

1Always unplug the machine from the electrical outlet immediately after using, when cleaning, making any user

servicing adjustments mentioned in this manual, or if you are leaving the machine unattended.

WARNING - To reduce the risk of burns, fire, electrical shock, or injury to

persons.

2Always unplug the machine from the electrical outlet when making any adjustments mentioned in the instruction

manual.

• To unplug the machine, switch the machine to the symbol “O” position to turn it off, then grasp the plug and pull

it out of the electrical outlet. Do not pull on the cord.

• Plug the machine directly into the electrical outlet. Do not use an extension cord.

• Always unplug your machine if there is a power failure.

3Electrical Hazards:

• This machine should be connected to an AC power source within the range indicated on the rating label. Do not

connect it to a DC power source or converter. If you are not sure what kind of power source you have, contact a

qualified electrician.

• This machine is approved for use in the country of purchase only.

4Never operate this machine if it has a damaged cord or plug, if it is not working properly, has been dropped or

damaged, or water is spilled on the unit. Return the machine to the nearest authorized Brother dealer for

examination, repair, electrical or mechanical adjustment.

• While the machine is stored or in use if you notice anything unusual, such as an odor, heat, discoloration or

deformation, stop using the machine immediately and unplug the power cord.

• When transporting the machine, be sure to carry it by its handle. Lifting the machine by any other part may

damage the machine or result in the machine falling, which could cause injuries.

• When lifting the machine, be careful not to make any sudden or careless movements, which may cause a

personal injury.

INTRODUCTION

IMPORTANT SAFETY INSTRUCTIONS

ii

5Always keep your work area clear:

• Never operate the machine with any air openings blocked. Keep ventilation openings of the machine and foot

control free from the build up of lint, dust, and loose cloth.

• Do not store objects on the foot controller.

• Do not use extension cords. Plug the machine directly into the electrical outlet.

• Never drop or insert foreign objects in any opening.

• Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

• Do not use the machine near a heat source, such as a stove or iron; otherwise, the machine, power cord or

garment being sewn may ignite, resulting in fire or an electric shock.

• Do not place this machine on an unstable surface, such as an unsteady or slanted table, otherwise the machine

may fall, resulting in injuries.

6Special care is required when sewing:

• Always pay close attention to the needle. Do not use bent or damaged needles.

• Keep fingers away from all moving parts. Special care is required around the machine needle.

• Switch the machine to the symbol “O” position to turn it off when making any adjustments in the needle area.

• Do not use a damaged or incorrect needle plate, as it could cause the needle to break.

• Do not push or pull the fabric when sewing, and follow careful instruction when free motion stitching so that

you do not deflect the needle and cause it to break.

7This machine is not a toy:

• Your close attention is necessary when the machine is used by or near children.

• The plastic bag that this machine was supplied in should be kept out of the reach of children or disposed of.

Never allow children to play with the bag due to the danger of suffocation.

• Do not use outdoors.

8For a longer service life:

• When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine

near a space heater, iron, halogen lamp, or other hot objects.

• Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the

case and machine, and should never be used.

• Always consult the Operation Manual when replacing or installing any assemblies, the presser feet, needle, or

other parts to assure correct installation.

9For repair or adjustment:

• If the light unit is damaged, it must be replaced by an authorized Brother dealer.

• In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of

the Operation Manual to inspect and adjust the machine yourself. If the problem persists, please consult your

local authorized Brother dealer.

Use this machine only for its intended use as described in the manual.

Use accessories recommended by the manufacturer as contained in this manual.

The contents of this manual and specifications of this product are subject to change without notice.

For additional product information, visit our website at www.brother.com

IMPORTANT SAFETY INSTRUCTIONS

iii

SAVE THESE INSTRUCTIONS

This machine is intended for household use.

FOR USERS IN COUNTRIES EXCEPT EUROPEAN COUNTRIES

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of the

appliance by a person responsible for their safety. Children should be supervised

to ensure that they do not play with the appliance.

FOR USERS IN EUROPEAN COUNTRIES

This appliance can be used by children aged from 8 years and above and persons

with reduced physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved. Children shall not

play with the appliance. Cleaning and user maintenance shall not be made by

children without supervision.

FOR USERS IN THE UK, EIRE, MALTA

AND CYPRUS ONLY

IMPORTANT

• In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the mark,

rating as marked on plug.

• Always replace the fuse cover. Never use plugs with the fuse cover omitted.

• If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your

authorized Brother dealer to obtain the correct lead.

ABOUT THIS MANUAL

iv

This manual was written for several machine models.

The machine models are categorized according to their specifications and referred to as “Model” followed by a number.

Refer to the Quick Reference Guide for the model of your machine.

The screen displays may differ from the ones displayed on your machine.

Refer to the Quick Reference Guide for details on accessories, settings screen and pre-programmed stitch patterns.

First, read “Functions available with each model” and “Using the utility stitch tables in the “Sewing” section” on page B-8.

ABOUT THIS MANUAL

WHAT YOU CAN DO WITH THIS MACHINE

B Basic operations

After purchasing your machine, be sure to read this section first. This section provides details on the initial setup

procedures as well as descriptions of this machine’s more useful functions.

Chapter 1 GETTING READY

Page B-2

To learn the operation of the principal parts and the screens

Chapter 2 STARTING TO SEW

Page B-33

To learn how to prepare for sewing and basic sewing operations

S Sewing

This section describes procedures for using the various utility stitches as well as other functions. It provides details on

basic machine sewing in addition to the more expressive features of the machine, such as sewing tubular pieces and

buttonholes.

Chapter 1 SEWING ATTRACTIVE FINISHES

Page S-2

Tips for sewing attractive finishes and various fabrics

Chapter 2 UTILITY STITCHES

Page S-6

Sew pre-programmed frequently used stitches

D Decorative sewing

This section provides instructions on sewing character stitches and decorative stitches as well as on adjusting and editing

them. In addition, it describes how to use MY CUSTOM STITCH, which allows you to create original stitch patterns.

Chapter 1 CHARACTER / DECORATIVE STITCHES

Page D-2

The variety of stitches widen your creativity

Chapter 2 MY CUSTOM STITCH

Page D-12

Create original decorative stitches

A Appendix

This section provides important information for operating this machine.

Chapter 1 MAINTENANCE AND TROUBLESHOOTING

Page A-2

The various maintenance and troubleshooting procedures are described.

CONTENTS

v

INTRODUCTION.................................................. i

IMPORTANT SAFETY INSTRUCTIONS ................. i

ABOUT THIS MANUAL ...................................... iv

WHAT YOU CAN DO WITH THIS MACHINE.... iv

B Basic operations

Chapter 1 GETTING READY 2

Names of Machine Parts and Their Functions ...... 2

Machine ................................................................................ 2

Needle and presser foot section .................................................. 3

Operation buttons.................................................................. 3

Operation panel and operation keys ...................................... 4

Using the flat bed attachment ................................................ 5

Included accessories .............................................................. 6

Optional accessories.............................................................. 7

Functions available with each model ..................................... 8

Using the utility stitch tables in the “Sewing” section ............. 8

Turning the Machine On/Off................................ 9

Turning on the machine....................................................... 10

Turning off the machine....................................................... 10

Select machine setting for the first time ................................ 10

LCD .................................................................... 11

Viewing the LCD ................................................................. 11

Settings screen ..................................................................... 12

Choosing the display language............................................. 14

Adjusting input sensitivity for operation keys ....................... 14

Winding/Installing the Bobbin............................ 15

Winding the bobbin ............................................................. 15

Installing the bobbin ............................................................ 18

Upper Threading ................................................ 21

Threading the upper thread.................................................. 21

Threading the needle ........................................................... 23

Threading the needle manually (without using the needle

threader) .............................................................................. 24

Pulling up the bobbin thread................................................ 24

Using the twin needle .......................................................... 25

Replacing the Needle ......................................... 28

Fabric/thread/needle combinations ...................................... 28

Checking the needle ............................................................ 29

Replacing the needle ........................................................... 29

Replacing the Presser Foot ................................. 31

Replacing the presser foot .................................................... 31

Removing and attaching the presser foot holder................... 32

Chapter 2 STARTING TO SEW 33

Sewing................................................................ 33

Stitch selection methods ...................................................... 33

Selecting a stitch pattern ...................................................... 34

Sewing a stitch..................................................................... 35

Sewing reinforcement stitches.............................................. 37

Automatic reinforcement stitching ....................................... 37

Setting the Stitch ................................................ 39

Setting the stitch width......................................................... 39

Setting the stitch length ........................................................ 39

Setting the thread tension..................................................... 40

Saving stitch settings ............................................................ 41

Useful Functions................................................. 42

Automatically cutting the thread .......................................... 42

Mirroring stitches ................................................................. 42

Adjusting the presser foot pressure ....................................... 43

Automatic Fabric Sensor System (Automatic presser foot

pressure) .............................................................................. 43

Pivoting ............................................................................... 43

Sewing with free motion mode............................................. 44

Hands-free raising and lifting of the presser foot ................... 45

Stitch Setting Chart............................................ 46

S Sewing

Chapter 1 SEWING ATTRACTIVE

FINISHES 2

Sewing Tips.......................................................... 2

Trial sewing............................................................................ 2

Changing the sewing direction

.................................................. 2

Sewing curves ........................................................................ 2

Sewing cylindrical pieces ....................................................... 2

Sewing an even seam allowance ............................................ 3

Sewing Various Fabrics ........................................ 4

Sewing thick fabrics ............................................................... 4

Sewing thin fabrics ................................................................. 4

Sewing stretch fabrics............................................................. 5

Sewing leathers or vinyl fabrics .............................................. 5

Sewing hook-and-loop fastener tape....................................... 5

Chapter 2 UTILITY STITCHES 6

Basic Stitching...................................................... 6

Basting ................................................................................... 6

Basic stitching ........................................................................ 6

Blind Hem Stitching ............................................. 8

Overcasting Stitches .......................................... 11

Sewing overcasting stitches using overcasting foot “G” ........ 11

Sewing overcasting stitches using zigzag foot “J”.................. 12

Sewing overcasting stitches using the side cutter

(sold separately with some models) ...................................... 12

Buttonhole Stitching/Button Sewing .................. 14

Buttonhole sewing................................................................ 14

Button sewing ...................................................................... 17

Zipper Insertion ................................................. 19

Inserting a centered zipper ................................................... 19

Inserting a side zipper .......................................................... 20

Zipper/piping Insertion ...................................... 23

Inserting a centered zipper ................................................... 23

Inserting a piping.................................................................. 24

Sewing Stretch Fabrics and Elastic Tape............. 25

Stretch stitching.................................................................... 25

Elastic attaching ................................................................... 25

Appliqué, Patchwork and Quilt Stitching........... 26

Appliqué stitching ................................................................ 26

Patchwork (crazy quilt) stitching........................................... 27

Piecing ................................................................................. 27

Quilting................................................................................ 29

Free motion quilting ............................................................. 30

Satin stitching using the sewing speed controller .................. 34

Reinforcement Stitching..................................... 35

Triple stretch stitching .......................................................... 35

Bar tack stitching.................................................................. 35

Darning................................................................................ 36

Eyelet Stitching .................................................. 38

Attaching Patches or Emblems to Shirt Sleeves

.... 39

Decorative Stitching .......................................... 41

Fagoting ............................................................................... 41

Scallop stitching ................................................................... 42

Smocking ............................................................................. 42

Shell tuck stitching ............................................................... 43

Joining.................................................................................. 43

Heirloom stitching................................................................ 44

CONTENTS

vi

D Decorative sewing

Chapter 1 CHARACTER / DECORATIVE

STITCHES 2

Sewing the Various Built-in Decorative Patterns

.... 2

Selecting stitch patterns .......................................................... 2

Deleting a pattern................................................................... 3

Sewing attractive finishes ....................................................... 3

Basic sewing .......................................................................... 4

Combining patterns ................................................................ 5

Repeating combined patterns ................................................. 5

Checking the selected pattern................................................. 6

Changing the pattern size ....................................................... 6

Changing the stitch density..................................................... 6

Changing the pattern length ................................................... 7

Changing character spacing ................................................... 7

Creating step stitch patterns.................................................... 7

Mirroring a pattern image....................................................... 8

Returning to the beginning of the pattern................................ 9

Saving a pattern...................................................................... 9

Retrieving a pattern .............................................................. 10

Realigning the pattern .......................................................... 10

Chapter 2 MY CUSTOM STITCH 12

Designing a Stitch............................................... 12

Drawing a sketch of the pattern............................................ 12

Entering the pattern data....................................................... 12

Examples of designs ............................................................. 14

A Appendix

Chapter 1 MAINTENANCE AND

TROUBLESHOOTING 2

Care and Maintenance.......................................... 2

Restrictions on oiling.............................................................. 2

Precautions on storing the machine........................................ 2

Cleaning the LCD screen........................................................ 2

Cleaning the machine surface ................................................ 2

Cleaning the race ................................................................... 2

Troubleshooting.................................................... 4

Frequent troubleshooting topics ............................................. 4

Upper thread tightened up ..................................................... 4

Tangled thread on wrong side of fabric .................................. 5

Incorrect thread tension.......................................................... 6

Fabric is caught in the machine and cannot be removed ........ 8

When the thread became tangled under the bobbin winder

seat ...................................................................................... 10

List of symptoms................................................................... 12

Error messages...................................................................... 17

Operation beep .................................................................... 20

Nothing appears in the LCD ................................................. 20

Specifications ..................................................... 20

Index .................................................................. 21

Basic

operations

This section provides details on the initial setup procedures as well as descriptions of this

machine’s more useful functions.

Page number starts with “B” in this section.

Chapter1 GETTING READY....................................................B-2

Chapter2 STARTING TO SEW ..............................................B-33

Names of Machine Parts and Their Functions

B-2

The names of the various parts of the machine and their functions are described below. Before using the machine,

carefully read these descriptions to learn the names of the machine parts and their locations.

Machine

■ Front view

1 Top cover

Open the top cover to place the spool of thread on the spool

pin.

2 Thread guide plate

Pass the thread around the thread guide plate when threading

the upper thread.

3 Bobbin winding thread guide and pretension disk

Pass the thread under this thread guide and around the

pretension disk when winding the bobbin thread.

4 Spool cap

Use the spool cap to hold the spool of thread in place.

5 Spool pin

Place a spool of thread on the spool pin.

6 Bobbin winder

Use the bobbin winder when winding the bobbin.

7 LCD (liquid crystal display)

Settings for the selected stitch and error messages appear in

the LCD. (page B-11)

8 Operation panel

From the operation panel, stitch settings can be selected and

edited, and operations for using the machine can be selected

(page B-4).

9 Knee lifter mounting slot

Insert the knee lifter into the knee lifter mounting slot.

0 Knee lifter

Use the knee lifter to raise and lower the presser foot.

(page B-45)

A Operation buttons and sewing speed controller

Use these buttons and the slide to operate the machine.

(page B-3)

B Flat bed attachment

Insert the presser foot accessory tray into the accessory

compartment of the flat bed attachment. Remove the flat bed

attachment when sewing cylindrical pieces such as sleeve

cuffs.

C Thread cutter

Pass the threads through the thread cutter to cut them.

D Needle threader lever

Use the needle threader lever to thread the needle.

E Thread tension dial

(Equipped on some models. Refer to page B-8)

Use the dial to adjust the upper thread tension. (page B-40)

■ Right-side/rear view

1 Handwheel

Turn the handwheel toward you (counterclockwise) to raise and

lower the needle to sew one stitch.

2 Handle

Carry the machine by its handle when transporting.

3 Presser foot lever

Raise and lower the presser foot lever to raise and lower the

presser foot.

4 Feed dog position switch

Use the feed dog position switch to lower the feed dogs.

5 Main power switch

Use the main power switch to turn the machine on and off.

6 Power supply jack

Insert the plug on the power supply cord into the power supply

jack.

7 Foot controller

Depress the foot controller to control the speed of the machine.

(page B-36)

8 Air vent

The air vent allows the air surrounding the motor to circulate.

Do not cover the air vent while the machine is being used.

9 Foot controller jack

Insert the plug on the end of the foot controller cable into the

foot controller jack.

Chapter 1

GETTING READY

Names of Machine Parts and Their Functions

a

b

c

d

e

f

h

i

j

k

l

m

n

o

g

a

b

c

d

e

f

g

h

i

Names of Machine Parts and Their Functions

GETTING READY

Basic operations B-3

B

Needle and presser foot section

1 Needle bar thread guide

Pass the upper thread through the needle bar thread guide.

2 Needle plate

The needle plate is marked with guides for sewing straight

seams.

3 Needle plate cover

Remove the needle plate cover to clean the bobbin case and

race.

4 Bobbin cover/bobbin case

Remove the bobbin cover, and then insert the bobbin into the

bobbin case.

5 Feed dogs

The feed dogs feed the fabric in the sewing direction.

6 Presser foot

The presser foot applies pressure consistently on the fabric as

the sewing takes place. Attach the appropriate presser foot for

the selected stitch.

7 Presser foot holder

The presser foot is attached onto the presser foot holder.

8 Presser foot holder screw

Use the presser foot holder screw to hold the presser foot in

place. (page B-32)

9 Buttonhole lever

Lower the buttonhole lever when sewing buttonholes and bar

tacks or when darning.

Operation buttons

1 “Start/Stop” button

Press the “Start/Stop” button to start or stop sewing. The

machine stitches at a slow speed at the beginning of sewing

while the button is pressed. When sewing is stopped, the

needle is lowered in the fabric. For details, refer to “STARTING

TO SEW” on page B-33.

The button changes color according to the machine’s

operation mode.

2 Reverse stitch button

For straight, zigzag, and elastic zigzag stitch patterns that use

reverse stitches, the machine will sew reverse stitches at low

speed only while holding down the Reverse stitch button. The

stitches are sewn in the opposite position.

For other stitches, use this button to sew reinforcement

stitches at the beginning and end of sewing. Press and hold

this button, and the machine sews 3 stitches in the same spot

and stops automatically. (page B-37)

3 Reinforcement stitch button

Use this button to sew a single stitch repeatedly and tie-off.

For character/decorative stitches, press this button to end with

a full stitch instead of at a mid-point. The LED light beside this

button lights up while the machine is sewing a full motif, and

automatically turns off when the sewing is stopped. (page B-

37)

4 Needle position button

Press the needle position button to raise or lower the needle.

Pressing the button twice sews one stitch.

5 Thread cutter button

Press the thread cutter button after sewing is stopped to cut

both the upper and the bobbin threads. For details, refer to

step

j under “Sewing a stitch” section on page B-35.

6 Presser foot lifter button

(Equipped on some models. Refer to page B-8)

Press this button to lower the presser foot and apply pressure

to the fabric. Press this button again to raise the presser foot.

7 Sewing speed controller

Slide the sewing speed controller to adjust the sewing speed.

i

b

a

c

d

e

f

g

h

Green: The machine is ready to sew or is sewing.

Red: The machine can not sew.

Orange: The machine is winding the bobbin thread, or

the bobbin winder shaft is moved to the right

side.

CAUTION

• Do not press (Thread cutter button) after

the threads have already been cut, otherwise

the needle may break, the threads may

become tangled or damage to the machine

may occur.

bcdef

a

g

Names of Machine Parts and Their Functions

B-4

Operation panel and operation keys

The keys with * are lit while they are ON.

1 LCD (liquid crystal display)

Settings for the selected stitch and error messages for

incorrect operations appear in the LCD.

For details, refer to “LCD” on page B-11

2 Pivot key *

(Equipped on some models. Refer to page B-8)

Press to activate pivot function.

3 Automatic reverse/reinforcement key *

Press to use the automatic reverse/reinforcement stitching

function.

4 Automatic thread cutting key *

Press to select the automatic thread cutting function.

5 Stitch length keys/Item selection keys

Press to adjust the stitch length or to select the next/previous

items in the settings screen.

6 Thread tension keys (Equipped on some models.

Refer to page B-8)/Value selection keys

Press to adjust the thread tension or to change the value of the

selected item in the settings screen.

7 Settings key

Press to select sewing settings or other settings, or to move to

next pages in the settings screen.

8 Manual memory key

Press to save the adjusted stitch width and length settings. For

models equipped with the thread tension keys (Refer to

page B-8.), the thread tension setting is also saved.

9 Mirror image key

Press to create a mirror image of the selected stitch pattern.

0 Single/repeat sewing key

Press to choose single pattern or continuous patterns.

A Back to beginning key

Press this key to return to the beginning of the pattern.

B Presser foot/Needle exchange key

Press this key before changing the needle, the presser foot,

etc.

This key locks all key and button functions to prevent operation

of the machine.

C Memory key

Press to save stitch pattern combinations to machine memory.

D Reset key

Press to reset the selected stitch to its original settings.

E OK key

Press to apply the selection or perform the operation.

F Numeric keys

Use these keys to quickly select one of the ten most often used

stitches. When selecting other stitches, use these keys to type

in the number of the desired stitch.

G Back key

Press this key to cancel the operation and return to the

previous screen.

In addition, pressing this key removes the last pattern added

when combining characters or decorative stitches.

H Character stitch key *

Press to select a character stitch.

I Decorative stitch key *

Press to select a decorative stitch.

J Utility stitch key *

Press to select a utility stitch.

K Preset utility stitch/saved pattern key *

Press to select the utility stitch assigned to a numeric key or to

retrieve a pattern that has been saved.

L Stitch width keys/Settings screen page selection

keys

Press to adjust the stitch width or to move to previous/next

pages in the settings screen.

b

g

e

l

r

q

s

t

u

a

f

c

d

h

i

j

k

m

n

o

p

v

Note

• The operation keys of this machine are

capacitive touch sensors. Operate the keys by

directly touching them with your finger.

The response of the keys varies according to the

user.

The pressure exerted on the keys does not affect

the response of the keys.

• Since the operation keys react differently

depending on the user, adjust the setting for the

input sensitivity. (page B-14)

• When using an electrostatic touch pen, make

sure that its point is 8 mm or more. Do not use a

touch pen with a thin point or a unique shape.

Names of Machine Parts and Their Functions

GETTING READY

Basic operations B-5

B

Using the flat bed attachment

Pull the top of the flat bed attachment to open the accessory

compartments.

A presser foot accessory tray is stored in the accessory

compartment of the flat bed attachment.

1 Storage space of the flat bed attachment

2 Presser foot accessory tray

1

2

Names of Machine Parts and Their Functions

B-6

Included accessories

Included accessories may differ from the table below depending on your model. For more details on included accessories and

their part codes of your machine, refer to the Quick Reference Guide.

1. 2. 3. 4. 5. 6.

Zigzag foot “J” (on machine) Monogramming foot “N” Overcasting foot “G” Zipper foot “I” Blind stitch foot “R” Button fitting foot “M”

7. 8. 9. 10. 11. 12.

Buttonhole foot “A” Needle set

75/11 2 needles, 90/14 2

needles, 90/14 2 needles: Ball

point needle (gold colored)

Twin needle

2.0/11 needle

Bobbin (4)

One is on machine.

Seam ripper Cleaning brush

13. 14. 15. 16. 17. 18.

Eyelet punch Screwdriver (large) L-shaped screwdriver Disc-shaped screwdriver Horizontal spool pin Spool cap (large)

19. 20. 21. 22. 23. 24.

Spool cap (medium) (2)

One is on machine.

Spool cap (small) Thread spool insert (mini king

thread spool)

Spool net Knee lifter Foot controller

25. 26. 27. 28.

Accessory bag Grid sheet set Operation Manual Quick Reference Guide

Note

• (For U.S.A. only) Foot controller: Model T

This foot controller can be used on the machine with product code 888-F50/F60/F70. The product code is

mentioned on the machine rating plate.

• The presser foot holder screw is available through your authorized Brother dealer. (Part code: XG1343-001)

• The presser foot accessory tray is available, through your authorized Brother dealer. (Part code: XF8650-001)

J

N

G

I

R

M

A

Names of Machine Parts and Their Functions

GETTING READY

Basic operations B-7

B

Optional accessories

The following are available as optional accessories to be purchased separately. Optional accessories differ depending on your

model. For more optional accessories and their part codes, refer to the Quick Reference Guide.

1. 2. 3. 4. 5. 6.

Free motion echo quilting foot

“E”

Free motion quilting foot “C” Quilting foot Walking foot 1/4" quilting foot 1/4" quilting foot with guide

7. 8. 9. 10. 11. 12.

Quilting guide Side cutter “S” Open toe foot Free motion open toe

quilting foot “O”

Non stick foot Stitch guide foot “P”

13. 14.

Adjustable zipper/piping foot Straight stitch foot and needle

plate set

Memo

• To obtain optional accessories or parts, contact your authorized Brother dealer.

• All specifications are correct at the time of printing. Please be aware that some specifications may change without

notice.

• Visit your nearest authorized Brother dealer for a complete listing of optional accessories available for your machine.

• Always use accessories recommended for this machine.

O

P

Names of Machine Parts and Their Functions

B-8

Functions available with each model

Specifications differ depending on the machine model. For

the functions available with your sewing machine model,

refer to the table below. Refer to the Quick Reference Guide

for the model of your sewing machine.

*1

Pattern size can be changed for decorative stitches, satin

stitches and all fonts of character stitches.

*2

Pattern size can be changed for character stitches other

than handwriting font.

Using the utility stitch tables in the “Sewing”

section

The utility stitch numbers differ depending on the model of

your machine. Refer to the Quick Reference Guide for the

model of your sewing machine.

Model 3 Model 2 Model 1 Page

Automatic fabric

sensor system

(setting)

9

N/A N/A B-43

Fine adjustment

horizontal (setting)

99

N/A D-10

Free motion foot

height (setting)

9

N/A N/A B-44

Free motion mode

(setting)

9

N/A N/A B-44

Pivoting

9

N/A N/A B-43

Presser foot height

(setting)

9

N/A N/A B-13

Presser foot lifter

button

9

N/A N/A B-3

Size selection

(setting)

999

D-6

Step stitch pattern

99

N/A D-7

Thread tension dial N/A N/A

9

B-40

Thread tension key

99

N/A B-40

*1

*2

Stitch name Stitch

Model 4

Presser foot

Model 3, 2

Model 1

Stitch number

Basting stitch 1-08 08 07

J

Straight stitch (Left)

1-01

01

* 01*

1-02

02

* 02*

Straight stitch (Middle) 1-03

03

* 03*

Triple stretch stitch 1-05

05

* 05*

Turning the Machine On/Off

GETTING READY

Basic operations B-9

B

Turning the Machine On/Off

WARNING

• Use only regular household electricity for the power source. Using other power sources may result in fire,

electric shock, or damage to the machine.

• Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and the power

cord receptacle on the machine. Otherwise, a fire or electric shock may result.

• Do not insert the plug on the power cord into an electrical outlet that is in poor condition.

• Turn the main power to OFF and remove the plug in the following circumstances:

When you are away from the machine

After using the machine

When the power fails during use

When the machine does not operate correctly due to a bad connection or a disconnection

During electrical storms

CAUTION

• Use only the power cord included with this machine.

• Do not use extension cords or multi-plug adapters with any other appliances plugged into them. Fire or

electric shock may result.

• Do not touch the plug with wet hands. Electric shock may result.

• When unplugging the machine, always turn the main power to OFF first. Always grasp the plug to remove

it from the electrical outlet. Pulling on the cord may damage the cord, or lead to fire or electric shock.

• Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted, or bundled.

Do not place heavy objects on the cord. Do not subject the cord to heat. These things may damage the

cord, or cause fire or electric shock. If the cord or plug is damaged, take the machine to your authorized

Brother dealer for repairs before continuing use.

• Unplug the power cord if the machine is not to be used for a long period of time. Otherwise, a fire may

result.

• When leaving the machine unattended, either the main switch of the machine should be turned to OFF or

the plug must be removed from the electrical outlet.

• When servicing the machine or when removing covers, the machine must be unplugged.

• For USA only

This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electrical

shock, this plug is intended to fit in a polarized electrical outlet only one way.

If the plug does not fit fully in the electrical outlet, reverse the plug. If it still does not fit, contact a

qualified electrician to install the proper electrical outlet. Do not modify the plug in any way.

Turning the Machine On/Off

B-10

Turning on the machine

a

Make sure that the machine is turned off (the main

power switch is set to “ ”), and then plug the power

cord into the power supply jack on the right side of the

machine.

b

Insert the plug of the power cord into a household

electrical outlet.

1 Power supply jack

2 Main power switch

c

Press the right side of the main power switch on the

right side of the machine to turn the machine on (set it

to “I”).

→ The light, LCD and the “Start/Stop” button light up

when the machine is turned on.

Turning off the machine

When you are finished using the machine, turn it off. In

addition, before transporting the machine to another location,

be sure to turn it off.

a

Make sure that the machine is not sewing.

b

Press the main power switch on the right side of the

machine in the direction of the “ ” symbol to turn

the machine off.

Select machine setting for the first time

When you first turn on the machine, select the language of

your choice. Follow the procedure below when the settings

screen appears automatically.

a

Use the “-” or “+” key to choose the desired language.

b

Press .

Memo

• When the machine is turned on, the needle and

the feed dogs will make a sound when they move;

this is not a malfunction.

• If the machine is turned off in the middle of sewing

in the “Sewing” function, the operation will not

resume after turning the power on again.

1

2

LCD

GETTING READY

Basic operations B-11

B

Viewing the LCD

When the power is turned on, the LCD comes on, and the following screen is displayed. The screen will vary slightly depending

on your machine model.

The screen is changed using the keys below the LCD.

LCD

No. Display Item Name Explanation Page

1 Presser foot Shows presser foot to be used. B-31

2 - Stitch preview Shows a preview of the selected stitch. B-34

3 Stitch category Shows the category of the currently selected stitch pattern.

: Preset utility stitch

: Utility stitch

: Decorative stitch (category 1)

: Decorative stitch (category 2)

: Decorative stitch (category 3)

: Character stitch (Gothic font)

: Character stitch (Handwriting font)

: Character stitch (Outline)

: Character stitch (Cyrillic font)

: Character stitch (Japanese font)

B-33

4 - Stitch number Shows the number of the currently selected stitch pattern. B-46

5 Needle position setting Shows single or twin needle mode setting, and the needle stop position.

: Single needle/down position

: Single needle/up position

: Twin needle/down position

: Twin needle/up position

B-12

6 Single/repeat sewing Shows single or continuous patterns sewing mode setting.

: Single sewing mode

: Repeat sewing mode

D-5

7 Horizontal mirror image Appears when the stitch is mirrored. B-42

8 Stitch width Shows the stitch width of the currently selected stitch pattern. B-39

9 Stitch length Shows the stitch length of the currently selected stitch pattern. B-39

0 Thread tension

(Equipped on some

models. Refer to page

page B-8)

Shows the automatic thread tension setting for the currently selected stitch pattern. B-40

5

6

3

1

7

2

8 9 0

4

5

6

3

1

7

2

8 9

4

LCD

B-12

Settings screen

Press to change various sewing machine operations and sewing settings.

Press to move to previous/next pages.

* You can also move to next pages by pressing .

Press to select the next/previous items.

* Press (Downward arrow) to select the next item.

* Press (Upward arrow) to select the previous item.

Press to change the value of the selected item.

1 Page number (The page numbers vary depending on your machine model.)

2 Machine settings

3 Value

1 Use to check the pattern when the specified pattern is not displayed on the screen. For details, refer to “Checking the selected

pattern” in the “Decorative sewing” section.

2 Select the needle stop position (the needle position for when the machine is not being operated) to be up or down.

3 Set to “ON” when using twin needle. For details, refer to “Using the twin needle” on page B-25.

4 Allows the stitch width to be adjusted using the sewing speed controller. For details, refer to “Satin stitching using the sewing

speed controller” in the “Sewing” section.

5 Select either “01 Straight stitch (Left)” or “03 Straight stitch (Middle)” as the utility stitch that is automatically selected when the

machine is turned on.

6 Changes the stitch length when 7 mm satin stitch patterns are selected. For details, refer to “Changing the pattern length” in the

“Decorative sewing” section.

7 Changes the thread density when satin stitch patterns are selected. For details, refer to “Changing the stitch density” in the

“Decorative sewing” section.

8 Changes the character spacing. For details, refer to “Changing character spacing” in the “Decorative sewing” section.

Note

• The parameters and number of pages in the settings screens differ depending on the model of your machine. For

details on the settings screen for your machine, refer to the Quick Reference Guide.

2

1

3

1

2

3

4

5

6

7

8

Page is loading ...

Brother Innov-is BQ1350 User manual

This manual is also suitable for

Brother Innov-is BQ1350 User manual

Related papers

Other documents