dBTechnologies ES62 User manual

MANUALE D’USO – Sezione 1

USER MANUAL - Section 1

BEDIENUNGSANLEITUNG - Abschnitt 1

CARACTERISTIQUES TECHNIQUES - Section 1

MANUAL DEL USUARIO - Sección 1

Le avvertenze nel presente manuale devono essere osservate congiuntamente al “MANUALE D’USO - Sezione 2”.

The warnings in this manual must be observed together with the "User Manual - Section 2".

Die Warnungen in diesem Handbuch müssen in Verbindung mit der "BEDIENUNGSANLEITUNG - Abschnitt 2" beobachtet werden.

Les avertissements speciés dans ce manuel doivent être respectés ainsi que les "CARACTERISTIQUES TECHNIQUES -Section 2"

Las advertencias del presente manual se deben tener en cuenta conjuntamente con las del “Manual del usuario” - Sección 2”

2

ES 602 - 802 Cod. 420120228 REV. 1.2

EMI CLASSIFICATION

FCC CLASS B STATEMENT ACCORDING TO TITLE 47, CHAPTER I,

SUBCHAPTER A, PART 15, SUBPART B

According to the standards EN 55103 this equipment is designed and suitable to operate in E3 (or lower E2, E1)

Electromagnetic environments.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to

persons or properties. For safety reasons di not place one loudspeaker on top of another without proper fastening

systems. Before hanging the loudspeaker check all the components for damages, deformations, missing or

damaged parts that may compromise safety during installation. If you use the loudspeakers outdoor avoid spots

exposed to bad weather conditions.

Contact dBTechnologies for accessories to be used with the speakers. dBTechnologies will not accept any

responsibility for damages caused by inappropiate accessories or additional devices.

WARNING

Page is loading ...

4

ES 602 - 802 Cod. 420120228 REV. 1.2

INDICE

1. INFORMAZIONI GENERALI ................................................................................................... 5

BENVENUTI! ........................................................................................................................ 5

PANORAMICA INTRODUTTIVA .......................................................................................... 5

RIFERIMENTI PER L’UTENTE ................................................................................................ 5

CARATTERISTICHE MECCANICHE ED ACUSTICHE ............................................................. 6

DIMENSIONI ............................................................................................................................................... 6

COPERTURA ACUSTICA ............................................................................................................................. 6

ACCESSORI ................................................................................................................................................. 6

CARATTERISTICHE DELLA SEZIONE DI AMPLIFICAZIONE E DI CONTROLLO ................... 7

SEZIONE DI INPUT E DI CONTROLLO ........................................................................................................ 8

SEZIONE DI ALIMENTAZIONE E COLLEGAMENTO DEL SATELLITE ........................................................... 9

2. PRIMA ACCENSIONE ............................................................................................................ 10

CONTENUTO DELLA CONFEZIONE .................................................................................. 10

INSTALLAZIONE ................................................................................................................ 11

MONTAGGIO DEL SATELLITE (ES 602) O DEI SATELLITI (ES 802) SUL SUBWOOFER ............................ 11

COLLEGAMENTO DEGLI INGRESSI .......................................................................................................... 12

COLLEGAMENTO DELL’ALIMENTAZIONE E DEL SATELLITE (ES 602) / SATELLITI (ES 802) ...................... 13

COLLEGAMENTO DELLE USCITE FRA PIU’ MODULI (rilancio del segnale audio) ................................ 15

3. PROGRAMMI PREIMPOSTATI DEL DSP INTERNO ............................................................. 16

4. RISOLUZIONE DEI PROBLEMI ............................................................................................. 17

5. SPECIFICHE TECNICHE ES 602 ............................................................................................. 18

GENERALE ................................................................................................................................................ 18

DATI ACUSTICI .......................................................................................................................................... 18

AMPLIFICATORE ....................................................................................................................................... 18

PROCESSORE ............................................................................................................................................ 19

INGRESSI ................................................................................................................................................... 19

DIMENSIONI ............................................................................................................................................. 19

6. SPECIFICHE TECNICHE ES 802 ............................................................................................. 20

GENERALE ................................................................................................................................................ 20

DATI ACUSTICI .......................................................................................................................................... 20

AMPLIFICATORE ....................................................................................................................................... 20

PROCESSORE ............................................................................................................................................ 21

INGRESSI ................................................................................................................................................... 21

DIMENSIONI ............................................................................................................................................. 21

Italiano

Page is loading ...

13

ES 602 - 802 REV. 1.1 Cod. 420120228 REV. 1.2

COLLEGAMENTO DELL’ALIMENTAZIONE E DEL SATELLITE

(ES 602) / SATELLITI (ES 802)

ATTENZIONE!

• Utilizzare solo cavi dotati di connettori

Neutrik®.

• Sostituire i cavi eventualmente

danneggiati, per evitare malfunzionamenti

ed una scarsa qualità del suono.

ES-TOP A

ALIMENTAZIONE

Italiano

Page is loading ...

23

ES 602 - 802 REV. 1.1 Cod. 420120228 REV. 1.2

INDEX

1. GENERAL INFORMATION ......................................................................................................24

WELCOME! .........................................................................................................................24

PRELIMINARY OVERVIEW ..................................................................................................24

USER REFERENCES ..............................................................................................................24

MECHANICAL AND ACOUSTIC CHARACTERISTICS ............................................................25

DIMENSIONS .............................................................................................................................................. 25

ACOUSTIC COVERAGE .............................................................................................................................. 25

ACCESSORI ................................................................................................................................................. 25

CHARACTERISTICS OF THE AMPLIFICATION AND CONTROL SECTION ............................26

INPUT AND CONTROL SECTION ................................................................................................................ 27

POWER SUPPLY AND SATELLITE CONNECTION SECTION ........................................................................ 28

2. FIRST SWITCH-ON ..................................................................................................................29

PACKAGE CONTENTS ..........................................................................................................29

INSTALLATION .....................................................................................................................30

INSTALLING THE SATELLITE (ES 602) OR THE SATELLITES (ES 802) ON THE SUBWOOFER .................... 30

CONNECTING THE INPUTS ........................................................................................................................ 31

CONNECTING THE POWER SUPPLY AND THE SATELLITE (ES 602) / SATELLITES (ES 802) ....................... 32

CONNECTING OUTPUTS BETWEEN MULTIPLE MODULES (audio signal linking) .................................. 34

3. INTERNAL DSP PRE-SET PROGRAMS ...................................................................................35

4. TROUBLESHOOTING ..............................................................................................................36

5. TECHNICAL SPECIFICATIONS ES 602 ....................................................................................37

GENERAL .................................................................................................................................................... 37

ACOUSTIC DATA ......................................................................................................................................... 37

AMPLIFIER ................................................................................................................................................. 37

PROCESSOR ................................................................................................................................................ 38

INPUTS........................................................................................................................................................ 38

DIMENSIONS .............................................................................................................................................. 38

6. TECHNICAL SPECIFICATIONS ES 802 ....................................................................................39

GENERAL .................................................................................................................................................... 39

ACOUSTIC DATA ......................................................................................................................................... 39

AMPLIFIER ................................................................................................................................................. 39

PROCESSOR ................................................................................................................................................ 40

INPUTS........................................................................................................................................................ 40

DIMENSIONS .............................................................................................................................................. 40

English

24

ES 602 - 802 Cod. 420120228 REV. 1.2

1. GENERAL INFORMATION

WELCOME!

PRELIMINARY OVERVIEW

USER REFERENCES

Thank you for purchasing a product designed and developed in Italy by dBTechnologies! The ES 602-802 series,

easy to transport, is the result of years of experience and research on acoustics, electronics and materials.

The ES 602-802 bi-amp system series is easy to transport, while providing excellent acoustic performance.

The subwoofer section is equipped with a 10” cone for ES 602 and with a 12” cone for ES 802; this ensures a

consistency at low frequencies which is not what one would expect from such a compact system. The tops of

both models have been designed using 4 3” transducers, in an optimised inner layout. This ensures an effective

acoustic coverage in different usage contexts, indoors and outdoors. The powerful DSP and the particular

exibility of the inputs also ensure great versatility; that’s why this series is the perfect choice for those who wish

a compact system, easy to transport but providing powerful PA amplication. The main characteristics are:

To get the most from your ES 602-802 we recommend that you:

• easy transport and installation - it can be installed in less than one minute

• optimised acoustic coverage of 95x65°

• medium to high-frequency section featuring a satellite with an innovative shape

• versatility of connections (LINE/MIC combo input, RCA stereo input, LINK output)

• thoroughly read the quick start user manual you will nd in the package and this manual, and keep it

throughout the product life

• register the product on the site http://www.dbtechnologies.com, in the “SUPPORT” section

• Keep the proof of purchase and the WARRANTY (User manual - section 2)

English

25

ES 602 - 802 REV. 1.1 Cod. 420120228 REV. 1.2

MECHANICAL AND ACOUSTIC CHARACTERISTICS

DIMENSIONS

ACOUSTIC COVERAGE

The ES 602 and ES 802 systems are compact; they can be easily

disassembled for transport and the main weight is that of the

subwoofer section: 14.2 kg for ES 602, 16.4 kg for ES 802. For the

installation of the satellite (ES 602) or of the 2 satellites (ES 802)

the package includes 2 25 mm poles with M20 threading, one of

which is telescopic and can be adjusted to reach a series of pre-

set heights, to a maximum total height of about 208 cm (81,89

inch.) for ES 602 and of about 245 cm (96,46 inch.) for ES 802.

The ES 602 and ES 802 systems feature an horizontal acoustic

coverage of 95° and a vertical one of 65°. For ES 802, thanks to

the accurate design of the 2 overlapping modules, ES-TOP A

and ES-TOP B, the overall coverage is the same once they have

been mounted in a stacked conguration.

ACCESSORI

For system transport and protection, the following items

are available:

• protective cover for the subwoofer (TC-ES10 for ES 602, TC-ES12 for ES 802)

• backpack-protective cover for satellites (TC-ESTOP)

• transport trolley DT-50

English

26

ES 602 - 802 Cod. 420120228 REV. 1.2

CHARACTERISTICS OF THE AMPLIFICATION AND CONTROL SECTION

The D-class latest generation digital amplier DIGIPRO G3 is the

core of the ES 602-802 systems; it provides a sound power of 800 W

(Power Amp - Peak) for ES 602, and of 1200 W (Power Amp - Peak)

for ES 802.

Thanks to a switching power supply section featuring a particularly

efcient auto-range function, the system is quiet, as it requires no

active cooling system.

The system is controlled by a powerful DSP, allowing to dene

different pre-sets, according to one’s usage and installation

requirements.

ATTENTION!

• Protect the module from humidity

• Never try to open the amplier

• In case of malfunction, immediately cut

off the power supply, by disconnecting the

module from the mains, then contact an

authorised repairman

The DIGIPRO G3 panel consists of:

• INPUT AND CONTROL SECTION

• POWER SUPPLY AND SATELLITE CONNECTION SECTION

INPUT AND

CONTROL SECTION

POWER SUPPLY

AND SATELLITE

CONNECTION SECTION

AMPLIFIER

English

27

ES 602 - 802 REV. 1.1 Cod. 420120228 REV. 1.2

2. “LINK” OUTPUT

It allows to link the output signal to another ES speaker

system or to another active speaker.

4. VOLUME MASTER CONTROL

It allows to adjust the master system volume.

5. DSP PRESET ROTARY

It allows to select through a rotary control the pre-set which is the most appropriate for the inputs and the

installation environment.

7. RCA-TYPE STEREO INPUT

A stereo input allowing to connect a device like a CD or MP3 player or other external equipment, in addition or as

an alternative to the main input, “CH1 CHANNEL” (1).

6. AUX VOLUME

It allows to adjust the auxiliary input volume.

ATTENTION!

• Never use the speaker for a prolonged time while the

limiter LED is on or blinking, indicating the equipment is

running under excessive stress conditions.

• Only use cables equipped with high-quality genuine

Neutrik® connectors. Using different or poor-quality

connectors might affect the speaker operation.

1. “CH1” CHANNEL

The “CH1” combo input allows to input both a connection from

MIXER/LINE and a microphone connection.

INPUT AND CONTROL SECTION

3. LIMITER LED AND ON-SIGNAL LED

When on, the limiter LED indicates that the internal protection circuit,

protecting the amplier from distortion and the transducers from overloads,

has been activated. The on-signal LED indicates the presence of the input audio

signal.

English

• Only use cables equipped with high-

quality genuine Neutrik® connectors.

English

28

ES 602 - 802 Cod. 420120228 REV. 1.2

8. LINE/MIC SELECTOR

It allows to select whether the incoming signal is a line signal or whether it comes from a microphone.

9. POWER SWITCH

ON (I) OFF (0) system power supply switch

10. POWER SUPPLY INPUT

Input for the connector of the supplied power cord.

11. SATELLITE CONNECTION OUTPUT

Output allowing to connect the system to the ES-TOP A satellite

through a SPEAKON balanced cable.

12. MAINS FUSE

POWER SUPPLY AND SATELLITE CONNECTION SECTION

ATTENTION!

• The speaker is supplied equipped with

a pre-installed fuse designed to operate

within the 220-240 V range. If the system

must operate within the 100-120 V range:

1. Disconnect all connections, including the

power supply one

2. Wait for 5 minutes

3. Replace the fuse with the one included in

the package for the 100-120 V range

English

29

ES 602 - 802 REV. 1.1 Cod. 420120228 REV. 1.2

2. FIRST SWITCH-ON

PACKAGE CONTENTS

Open the package and check that the ES 602-ES 802 system packaging contains all the items included in the

supply. The packaging includes:

1. power cord

2. ES SYSTEM:

• 602: 1 ES-SUB 602 subwoofer unit + 1 ES-TOP A satellite

• 802: 1 ES-SUB 802 subwoofer unit + 1 ES-TOP A satellite + 1 ES-TOP B satellite

3. 2 poles having a diameter of 25 mm, with M20 threading, one of which telescopic, equipped with

height adjustment pin and locking hand wheel

4. quick start and documents related to warranty/safety

5. fuse to be installed if the system is to operate within the 100-120V range

6. SPEAKON cable

ATTENTION!

• The speaker is supplied equipped with

a pre-installed fuse designed to operate

within the 220-240 V range. If the system

must operate within the 100-120 V range:

1. Disconnect all connections, including the

power supply one

2. Wait for 5 minutes

3. Replace the fuse with the one included in

the package for the 100-120 V range

4. Only use the supplied cable

English

30

ES 602 - 802 Cod. 420120228 REV. 1.2

INSTALLATION

INSTALLING THE SATELLITE (ES 602) OR THE SATELLITES (ES 802) ON THE

SUBWOOFER

1. Screw the lower 25 mm pole into

the specically designed hole on the

subwoofer top side, as shown.

2. Screw the telescopic pole onto the latter.

3. Then adjust the rod height, rst loosening

the hand wheel, then inserting the pin

into the hole of the telescopic rod at the

desired height. Then retighten the hand

wheel.

1. Insert the ES-TOP A speaker on the pole using the

hole located in the lower section.

1. Flip ES-TOP B and stack it onto ES-TOP A

as shown.

2. Then insert ES-TOP B into the guide of ES-

TOP A, ensuring that the contacts touch

each other

3. To complete the installation of the 2

speakers slightly move them to the

outside as shown in the gure until they

lock with a click.

ES 602 and 802:

ES 602:

ES 802:

ES-TOP A

ES-TOP B

upside down

English

31

ES 602 - 802 REV. 1.1 Cod. 420120228 REV. 1.2

CONNECTING THE INPUTS

4. Now insert the speaker assembly from the TOP A side using the hole

located on the bottom side.

ATTENTION!

• Make sure that ES-TOP A is rmly in

place, but never forcibly rotate it during

installation, do avoid damaging the

coupling system.

• Never transport the ES-TOP A and ES-TOP

B speakers while they are coupled to each

other; always detach them when carrying

them to avoid damaging the couplings.

• For ES 802 only, make sure that you install

ES-TOP A on the pole as shown in the

gure and and not ES-TOP B, as the cable

needs to be connected from the subwoofer

to this specic satellite.

MIXER / LINE MICROPHONE

ES-TOP A

AUX IN AUX IN

English

32

ES 602 - 802 Cod. 420120228 REV. 1.2

CONNECTING THE POWER SUPPLY AND THE SATELLITE (ES 602) /

SATELLITES (ES 802)

ATTENTION!

• Only use cables equipped withNeutrik®

connectors. Replace any damaged cables,

to avoid malfunctions and poor sound

quality

POWER SUPPLY

ES-TOP A

English

33

ES 602 - 802 REV. 1.1 Cod. 420120228 REV. 1.2

To properly install the ES 602 / ES 802 speaker:

• Perform the connection to the main input (1) using a cable equipped with a XLR (balanced) or TRS

(unbalanced) connector. For an overview of the most common cables available for audio connection

please refer to the table below. Depending on the source (line/mixer or microphone), set the relevant

selector (8) to the appropriate value. Turn the MASTER CONTROL (4) volume to the minimum level.

• If any, connect the secondary stereo input with RCA-type cables, setting the AUX VOLUME (6) to the

minimum level. Later you’ll be able to mix the signal from this auxiliary input with the main input

signal, through the respective volumes. Remember that the MASTER CONTROL (4) still controls the

overall system output volume.

• Temporarily set DSP PRESET (5) to FLAT.

• Using the supplied SPEAKON cable, connect the output of the TOP OUTPUT MONO (11) output to the

ES-TOP A input, for both one (ES 602), and two (ES 802) satellite installations.

• Insert the power supply connector into the relevant input (10), then turn the POWER selector to

position “I”.

• The PEAK LED (3) temporarily lights up, then it goes off

• Progressively increase the master (4) and auxiliary (6, if any) volumes

• It should be noticed that the ON-SIGNAL LED (3) blinks to indicate the presence of the input audio

signal

• Use the DSP PRESET (5) position that is the most appropriate for the application.

English

34

ES 602 - 802 Cod. 420120228 REV. 1.2

The audio signal can be linked using a balanced XLR cable connection to a second unit, then in a cascade to a

third one, and so on. To link the audio signal connect the LINK output (2) of the rst ES 602 or ES 802 to the input

(1) of a second device. Perform the connection with the downstream system by turning the relevant selector (8) to

the LINE position. The volumes of the linked systems will be independent of each other.

CONNECTING OUTPUTS BETWEEN MULTIPLE MODULES (audio signal linking)

LINK

English

35

ES 602 - 802 REV. 1.1 Cod. 420120228 REV. 1.2

3. INTERNAL DSP PRE-SET PROGRAMS

The powerful DSP of the ES 602-802 systems provides 8 congurations, allowing to digitally equalise the audio

signal according to different pre-set contexts and different usage needs. To select the relevant program just use a

small screwdriver and turn the rotary control to the desired program number:

1. FLAT: the setting performs no equalisation, directly outputting the input signal with no changes

2. BASS BOOST: it emphasises the low frequencies

3. BASS REDUCTION: it reduces the low frequencies, and is particularly suitable for reverberating

environments, to improve intelligibility.

4. PLAYBACK: it performs an equalisation that is particularly suitable for the playback of music tracks from

sources like CDs, MP3 players or other portable systems.

5. CLUB: this setting helps equalising frequencies to improve listening in small indoor environments

6. VOCAL: an equalisation emphasising the voice frequency range, particularly suitable when a

microphone has been connected to input (1), and the relevant selector (8) has been set to MIC, or for

the playback of speech.

7. MONITOR: This setting is suitable when using the ES 602-802 system as a personal monitor.

8. ANTIFEEDBACK: a setting using a notch lter to minimise the feedback risk, particularly when a cardioid

or hypercardioid microphone is used.

English

36

ES 602 - 802 Cod. 420120228 REV. 1.2

4. TROUBLESHOOTING

1. Check that the power supply upstream of the system is working properly

2. Check that the power cord is properly plugged

3. Check that the ON/OFF selector is turned to “I”.

1. Check that the input connections of the main audio signal and of the auxiliary one, if any, have been

performed properly

2. Check that the cables in use are not damaged

3. Check that the mixer or the audio source are on and that they clearly indicate the presence of an

output signal to the speaker.

4. Check that the level of the main audio volume and of the auxiliary one, if any, are set to an appropriate

value

1. Adjust the source volume rst, then set the ES 602 or ES 802 system input volume to an appropriate

value

2. Check that the cables in use are not damaged; should that be the case, replace them (a damaged cable

may result in a signal loss or alteration)

1. Turn off the system and disconnect the audio connection between the subwoofer and the satellites

2. Check the integrity of the audio cable used for the connection

3. Uninstall and properly reinstall the 2 satellites A and B, checking that there are no mechanical

clearances.

4. Properly reconnect the output of the “TOP OUTPUT MONO A” subwoofer to the ES-TOP A input.

5. Turn on the system, then progressively increase the input volume and the auxiliary one, if any.

The speaker doesn’t turn on:

The speaker turns on but it doesn’t output any sound:

The speaker outputs a distorted sound:

The 2 satellites of the ES-802 system (ES-TOP A + ES-TOP B) don’t output any sound:

English

37

ES 602 - 802 REV. 1.1 Cod. 420120228 REV. 1.2

5. TECHNICAL SPECIFICATIONS ES 602

GENERAL

ACOUSTIC DATA

AMPLIFIER

Type 2-way active system consisting of a full-range top and a subwoofer

Frequency Response [-10dB]: 44 - 15000 Hz

Max SPL: 118 dB

MF-HF: 4x3”

Type MF- HF: Neodymium

Crossover frequency: 210 Hz

Directivity (HxV): 95”x65”

LF: 10”

Type: Digipro® G3

Amplication class: D class

Amplication power (Power Amp): 800 W

Power supply: SMPS con PSU Auto-range

Power supply connector: Socket VDE

Cooling technique: Convection

Controls:

1 Rotary control for pre-sets, 1 LED monitoring the input audio

signal

Inrush current: 18,2 A

English

38

ES 602 - 802 Cod. 420120228 REV. 1.2

PROCESSOR

INPUTS

DIMENSIONS

Internal controller: DSP 24 bit/48 kHz

System settings: Selectable pre-dened settings

Limiter: Dual active, Peak, RMS, ermal

Inputs: 1x Combo (XLR/Jack) balanced/unbalanced + 1 RCA stereo input

Outputs: 1x XLR link OUT, balanced

Subwoofer cabinet: Plywood, thickness 15 mm

Satellite cabinet: Polypropylene PP

Handles: 2, lateral (in the subwoofer)

Installation on pole:

the supply includes 2 poles having a diameter of 25 mm, with M20

threading, one of which telescopic

Satellite height: 95 mm (3,74 inch.)

Satellite depth: 360 mm (13,98 inch.)

Profondità satellite: 430 mm (16,9 inch.)

Subwoofer width: 300 mm (13,8 inch.)

Subwoofer height: 400 mm (15,7 inch.)

Subwoofer depth: 430 mm (16,9 inch.)

Satellite weight: 1,9 kg (4,19 lbs.)

Subwoofer weight: 14,2 kg (31,48 lbs)

English

Page is loading ...

dBTechnologies ES62 User manual

This manual is also suitable for

dBTechnologies ES62 User manual

in other languages

Related papers

Other documents