Samsung SP-56L5HX User manual

COLOUR

TELEVISION

SP43L2HX

SP50L2HX

SP61L2HX

SP46L5HX

SP56L5HX

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

P

ICTURE IN PICTURE (PIP)

TELETEXT

2

ENG

Safety Instructions

◆ Do not expose the television to extreme temperature conditions or to extreme humidity conditions.

◆ Do not expose the television to direct sunlight and other sources of heat.

◆ Do not expose the television to any liquids.

◆ Never put objects of any kind into the television, and do not place a water-containing vessel on the

television.

◆ During a storm conditions (especially when there is lightning) unplug the television from the mains

socket and aerial.

◆ Do not step on or twist the power cord.

◆ Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.

◆ Please use a soft and dry cloth (not containing volatile matter) when you clean the TV.

◆ If the television is broken, do not try to repair it yourself. Contact qualified service personnel.

◆ If the remote control is not used for a long period of time, remove the batteries and store it in a

cool, dry place.

◆ Do not drop the remote control.

This device is not for use in industrial environments.

Caution

WARNING: TO PREVENT DAMAGE WHICH MAY RESULT

IN FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRICAL SHOCK,

DO NOT REMOVE REAR COVER, NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

The lightning flash and arrow head

within the triangle is a warning sign

alerting you of “dangerous voltage”

inside the product.

The exclamation point within the

triangle is a warning sign alerting

you of important instructions

accompanying the product.

☛

The main voltage is indicated on the

rear of the TV set and the frequency is

50 or 60Hz.

3

ENG

Contents

◆ FOREWORD

■ Safety Instructions ......................................................................................... 2

■ Caution .......................................................................................................... 2

■ Replacing the Lamp....................................................................................... 5~6

◆ CONNECTING AND PREPARING YOUR TELEVISION

■ Control Panel of Your Television ................................................................... 7~8

■ Connection Panel of Your Television ............................................................ 9

■ Connecting to an Aerial or Cable Television Network ................................... 10

■ Connecting a Satellite Receiver or Decoder.................................................. 10

■ Connecting Additional Speakers ................................................................... 11

■ Inserting the Batteries in the Remote Control................................................ 11

■ Infrared Remote Control ................................................................................ 12

■ Switching Your Television On and Off........................................................... 13

■ Placing Your Television in Standby Mode..................................................... 13

■ Becoming Familiar with the Remote Control ................................................. 14

■ Plug & Play Feature....................................................................................... 15~16

■ Choosing Your Language.............................................................................. 16

◆ SETTING THE CHANNELS

■ Storing Channels Automatically..................................................................... 17

■ Storing Channels Manually............................................................................ 18~19

■ Skipping Unwanted Channels ....................................................................... 20

■ Sorting the Stored Channels ......................................................................... 21

■ Assigning Names to Channels ...................................................................... 22

■ Activating the Child Lock ............................................................................... 23

■ Selecting a Channel by Information............................................................... 24

◆ USING YOUR TELEVISION (continued)

■ Changing the Picture Standard ..................................................................... 25

■ Adjusting the Picture Settings........................................................................ 26

■ Adjusting the Picture Settings (PC or DVI Mode) .......................................... 27

■ Setting the Picture (PC Mode)....................................................................... 28

■ Using the Fine Tune ...................................................................................... 29

■ Viewing the Channel Scan Picture ................................................................ 30

■ Freezing the Current Picture ......................................................................... 30

■ Using the LNA (Low Noise Amplifier) Feature............................................... 31

■ Selecting the Picture Size.............................................................................. 32

■ Using the Digital NR (Digital Noise Reduction) Feature ................................ 33

■ DNIe

TM

(Digital Natural Image engine) ............................................... 34

■ Setting the Blue Screen................................................................................. 35

■ Selecting the Film Mode ................................................................................ 35

■ Changing the Sound Standard ...................................................................... 36

4

ENG

Contents (continued)

◆ USING YOUR TELEVISION

■ Adjusting the Sound Settings ........................................................................ 37

■ Adjusting the Volume Automatically .............................................................. 37

■ Setting the Dolby Pro Logic........................................................................... 38

■ Adjusting Your Dolby Preferences................................................................. 39

■ Setting the External Sound............................................................................ 40

■ Selecting the Sound Mode (depending on the model) .................................. 41

■ Setting the Melody Sound ............................................................................. 42

■ Setting the Sleep Timer ................................................................................. 43

■ Setting and Displaying the Current Time....................................................... 44

■ Switching the Television On and Off Automatically ....................................... 45

■ Viewing an External Signal Source ............................................................... 46

■ Viewing the Picture In Picture (PIP) .............................................................. 47~48

■ Listening to the Sound of the Sub Picture (PC or DVI Mode)........................ 49

◆ USING THE TELETEXT FEATURE

■ Teletext Feature ............................................................................................ 50

■ Displaying the Teletext Information ............................................................... 51

■ Selecting Display Options.............................................................................. 52

■ Selecting a Teletext Page.............................................................................. 53

◆ ADDITIONAL INFORMATION AND CONNECTIONS

■ Connecting to the External Input/Output ....................................................... 54

■ Connecting to the DVD Input......................................................................... 55

■ Connecting to the Audio Outputs................................................................... 55

■ Connecting to the Audio/Video Input............................................................. 56

■ Connecting to the S-Video Input.................................................................... 56

■ Connecting to the DVI Input .......................................................................... 57

■ Connecting to the PC Input ........................................................................... 57

■ Setting up Your PC Software (Windows only) ............................................... 58

■ Input Mode (PC/DVI) ..................................................................................... 59

■ Pin Configurations ......................................................................................... 60

■ Programming the Remote Control for Other Components ............................ 61

-

VCR Remote Control Codes ...................................................................... 62~63

-

Cable Box (CATV) Remote Control Codes ................................................ 63

-

DVD Remote Control Codes ...................................................................... 63

◆ RECOMMENDATIONS FOR USE

■ Troubleshooting: Before Contacting Service Personnel................................ 64

■ Technical Specifications ................................................................................ 65

☛

➢

Press Important Note

Symbols

5

ENG

1 Use a screwdriver to remove the screw.

2 Remove the Lamp cover.

3 Use a screwdriver to remove the screws securing the Lamp.

There are 2 screws: one on the up and one on the down.

When the screws have been completely unfastened, they will still

be connected to the body of the Lamp.

4 Separate the Lamp from the engine by holding the handle and

pulling it out.

5 To reinstall the Lamp, follow these steps in reverse order.

☛

A Projection TV lamp is a consumable item, and should be

replaced from time to time for best projector operation. If the

screen image becomes dark, or timer, lamp and Temp LEDs

flicker off at the same time, you may have to replace the lamp.

When changing the lamp, you should first verify the

type/model, and then use only the correct lamp replacement.

The code for lamp regulation and usage is marked on the

label. If you remove the lamp, you can identify this

replacement code. You should only replace the lamp with the

one of the same regulation code.

◆

If you wish to buy a new lamp,please phone your Service Center

or a nearby TV dealer, and tell them the model of your projection

unit.

◆

You can identify the lamp type on the left side of TV and the

lamp cover.

◆

The TV will be damaged if you use a lamp that is different from

the original supplied by the manufacturer. Be sure the

replacement lamp is the same model.

◆

Please don't remove the lamp except when replacing with a new

one.

◆

Please turn off TV power before changing a lamp and then

unplug after waiting 1 minute.

◆

The cooling fan will help cool the lamp so you can safely remove

it. The surface of the Lamp is very hot. Please wait for 30

minutes after turning off your projection TV to handle the lamp.

◆

Please keep the old lamp away from flammable articles and

children. Dispose of properly.

◆

Don't allow dirt or dust to accumulate inside the lamp cover or on

the Lamp.

◆

A dirty cover or lamp can catch fire, explode and cause electric

shock.

◆

Please don't touch the front glass of a new lamp or the glass of

the lamp container.

◆

If a new lamp is improperly handled,the quality of the screen

image can be affected and the expected life span of the lamp

can be reduced.

◆

Be sure to tighten the lamp cover on the TV after changing the

lamp. Note that the TV will not function if the lamp cover is not

securely attached. Please tighten the holding screw on the lamp

cover after it has been attached to the TV.

Replacing the Lamp (

SP43L2HX/SP50L2HX/SP61L2HX)

6

ENG

1 Use a screwdriver to remove the screw.

2 Remove the Lamp cover.

3 Use a screwdriver to remove the screws securing the Lamp.

There are 2 screws: one on the up and one on the down.

When the screws have been completely unfastened, they will still

be connected to the body of the Lamp.

4 Separate the Lamp from the engine by holding the handle and

pulling it out.

5 To reinstall the Lamp, follow these steps in reverse order.

☛

A Projection TV lamp is a consumable item, and should be

replaced from time to time for best projector operation. If the

screen image becomes dark, or timer, lamp and Temp LEDs

flicker off at the same time, you may have to replace the lamp.

When changing the lamp, you should first verify the

type/model, and then use only the correct lamp replacement.

The code for lamp regulation and usage is marked on the

label. If you remove the lamp, you can identify this

replacement code. You should only replace the lamp with the

one of the same regulation code.

◆

If you wish to buy a new lamp,please phone your Service Center

or a nearby TV dealer, and tell them the model of your projection

unit.

◆

You can identify the lamp type on the left side of TV and the

lamp cover.

◆

The TV will be damaged if you use a lamp that is different from

the original supplied by the manufacturer. Be sure the

replacement lamp is the same model.

◆

Please don't remove the lamp except when replacing with a new

one.

◆

Please turn off TV power before changing a lamp and then

unplug after waiting 1 minute.

◆

The cooling fan will help cool the lamp so you can safely remove

it. The surface of the Lamp is very hot. Please wait for 30

minutes after turning off your projection TV to handle the lamp.

◆

Please keep the old lamp away from flammable articles and

children. Dispose of properly.

◆

Don't allow dirt or dust to accumulate inside the lamp cover or on

the Lamp.

◆

A dirty cover or lamp can catch fire, explode and cause electric

shock.

◆

Please don't touch the front glass of a new lamp or the glass of

the lamp container.

◆

If a new lamp is improperly handled,the quality of the screen

image can be affected and the expected life span of the lamp

can be reduced.

◆

Be sure to tighten the lamp cover on the TV after changing the

lamp. Note that the TV will not function if the lamp cover is not

securely attached. Please tighten the holding screw on the lamp

cover after it has been attached to the TV.

Replacing the Lamp (

SP46L5HX/SP56L5HX)

7

ENG

Control Panel of Your Television

a

d

c

b

e

f

LED Indicators

➢

The actual configuration on your TV may be different, depending on

your model.

a

d

c

b

e

f

b

d

c

a

f

e

LED Indicators

( a ) Input Source Selection

( b ) Menu Display

( c ) Channel Selection

( d ) Volume Adjustment

( e ) Confirm your choice (Store or Enter)

( f ) Power On/Off

SP43L2/50L2HX SP61L2HX

SP46L5/56L5HX

8

ENG

( :On, :Blinking, :Off)

TIMER LAMP STAND BY/TEMP Indication

Standby mode.

A timer pilot lights when Timer Auto On or Off is selected.

Normal operation.

Normal operation (when Timer Auto On or Off is selected).

Lamp is warming up. The normal picture comes on after 25 seconds.

The normal picture comes on after 25 seconds. (when Timer Auto On or

Off is selected)

Air vent cover in the rear of the TV is not properly installed.

Inside temperature of the TV is over normal. Clean the air vent cover in the

rear of the TV. Turn the TV back on after 1 hour.

The lamp does not work, please contact an authorized Service Center for

assistance.

➢

Using the Buttons on the Panel

If the remote control no longer works or you have lost it, you can use controls on the panel of the TV to:

◆

Switch on the TV when it is in Standby mode and select channels ( ▲ CH ▼ or CH ).

◆

Access the menu ( MENU ).

◆

Adjust the volume (

-

VOL+ ).

◆

Switch among Video input modes ( TV/VIDEO ).

Control Panel of Your Television (continued)

9

ENG

Connection Panel of Your Television

➢

The actual configuration on your TV may be different, depending on

your model.

b

a

e

d

f

g

i

j

h

S-VIDEO 1

S-VIDEO 2

c

➣

For further details about connection, refer to pages 54~60.

a) 75Ω

Coaxial connector for Aerial or Cable

Network.

b) MONITOR OUT / AV1 / AV2 / AV3

Inputs or outputs for external devices, such as

VCR, DVD, video game device or video disc

players.

c) S-VIDEO 1 / S-VIDEO 2

Video input for external devices with an

S-Video output, such as a camcorder or VCR.

d) SURROUND SPEAKER (8Ω 15W)

Connectors for external rear speakers.

e) AUDIO OUT

Amplifier (L/R) or powered speaker (WOOFER)

connection to take full advantage of the

surround sound effect.

f) COMPONENT 1 / COMPONENT 2

Video (Y/PB/PR) and audio (L/R) inputs for

Component. (480i/480p, 576i/576p, 720p,

1080i)

g) PC AUDIO (L/R)

PC or DVI Audio inputs.

h) PC (15 Pin)

PC Video input.

i) DVI (24 Pin)

Video input for device with DVI input.

j) RS-232 (only for service)

b

a

c

Side of the TV

b

a

c

SP46L5HX/56L5HX

( a ) Video Input

( b ) Audio Inputs

( c ) S-Video Input

SP43L2HX/50L2HX/61L2HX

Rear of the TV

10

ENG

To view television channels correctly, a signal must be received by

the set from one of the following sources:

◆ An outdoor aerial

◆ A cable television network

◆ A satellite network

1 In the first three cases, connect the aerial or network input cable to

the 75Ω coaxial socket on the rear of the television.

2 If you are using an indoor aerial, you may need to turn it when

tuning your television until you obtain a picture that is both sharp

and clear.

For further details, refer to:

◆ “Storing Channels Automatically” on page 17.

◆ “Storing Channels Manually” on page 18.

Connecting to an Aerial or Cable Television Network

Rear of the TV

Cable Television

Network

or

Connecting a Satellite Receiver or Decoder

In order to watch television programmes broadcast via a

satellite network, you must connect a satellite receiver to the

rear of TV. Also, in order to descramble a coded

transmission signal, you must connect a decoder to the rear

of TV.

◆ Using a SCART cable

Connect the receiver (or decoder) SCART cable to one of

the SCART connectors on the rear of the television.

◆ Using a coaxial cable

Connect a coaxial cable to the:

-

Receiver (or Decoder) output socket.

-

Television aerial input socket.

➢ If you wish to connect both a satellite receiver (or decoder)

and a VCR, you should connect the:

◆ Receiver (or Decoder) to the VCR

◆ VCR to the television

Otherwise, connect the receiver (or decoder) directly to

the television.

Rear of the TV

S-VIDEO 1 S-VIDEO 2

Satellite receiver/

Decoder

S-VIDEO 1 S-VIDEO 2

11

ENG

Connecting Additional Speakers

You must insert or replace the batteries in the remote control when

you:

◆ Purchase the television

◆ Find that the remote control is no longer operating

correctly

1 Remove the cover on the rear of the remote control by pressing

the symbol ( ) downwards and then pulling firmly to remove it.

2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking

care to respect the polarities:

◆

-

on the battery against

-

on the remote control

◆

+

on the battery against

+

on the remote control

3 Replace the cover by aligning it with the base of the remote

control and pressing it back into place.

Inserting the Batteries in the Remote Control

To take advantage of the surround sound system, connect

additional speakers.

The speaker terminals are located on the rear of the television:

◆ Two for the left-hand surround speaker (marked L)

◆ Two for the right-hand surround speaker (marked R)

➢

To improve the quality of the sound, connect the:

◆ Red wire to the red terminal

◆ Black wire to the black terminal

Rear of the TV

12

ENG

Infrared Remote Control

POWER ON/OFF

DIRECT CHANNEL SELECTION

VOLUME INCREASE

TEMPORARY SOUND SWITCH-OFF

MENU DISPLAY/

TELETEXT INDEX

MOVE TO THE REQUIRED MENU

OPTION/

ADJUST AN OPTION VALUE

RESPECTIVELY

STILL THE MAIN PICTURE

➢

In the PIP mode, the main and

sub pictures are stilled

at the same time.

PICTURE EFFEECT SELECTION

EXTERNAL INPUT SELECTION/

TELETEXT HOLD

SWITCH REPEATEDLY BETWEEN THE

LAST TWO CHANNELS DISPLAYED

PICTURE SIZE

EXIT FROM ANY DISPLAY

PREVIOUS CHANNEL/

TELETEXT PREVIOUS PAGE

CONFIRM YOUR CHOICE

(STORE OR ENTER)

DISPLAY INFORMATION/

TELETEXT REVEAL

DISPLAY CHANNEL INFORMATION

ONE OR TWO-DIGIT CHANNEL

SELECTION

TUNER/CABLE NETWORK

SELECTION

SOUND EFFECT SELECTION

MAKE THE REMOTE CONTROL WORKS

FOR TV, VCR, CABLE-BOX (CATV),

DVD PLAYER, OR SET-TOP BOX (STB)

SOUND MODE SELECTION

VOLUME DECREASE

NEXT CHANNEL/

TELETEXT NEXT PAGE

➢

The performance of the remote control may be affected by bright light.

CURRENT TIME DISPLAY/

TELETEXT SUBPAGE

TELETEXT DISPLAY/

MIX BOTH TELETEXT INFORMATION

AND THE NORMAL BROADCAST

DNIe ON/DEMO/OFF/

TELETEXT SIZE SELECTION

AUTOMATIC SWITCH-OFF/

TELETEXT CANCEL

SET THE MBR CODE OF REMOTE

CONTROL FOR THE PRODUCTS

EXCEPT SAMSUNG PRODUCT

(OPTION)

INITIALIZE THE REMOTE CONTROL

SETTINGS WHEN IT HAS SOME

PROBLEMS OR DOESN'T WORK

WELL

➢

Please take off the batteries while

resetting. If not so, the remote

control will get damaged.

FASTEXT TOPIC SELECTION

WHEN YOU PRESS A BUTTON , ‘

’

APPEARS ALONG WITH SELECED MODE

(TV, VCR, CATV, DVD OR STB) AND

REMAINING BATTERIES ON LED

PIP FUNCTIONS;

- PIP ACTIVATING OR DEACTIVATING

(PIP ON)

- SWAPPING THE MAIN AND THE SUB

PICTURE (SWAP)

- SELECTING THE CHANNEL OF SUB

PICTURE (P / )

VCR/DVD FUNCTIONS;

- REWIND (REW : )

- STOP

()

- PLAY/PAUSE

()

- FAST FORWARD (FF : )

13

ENG

The mains lead is attached to the rear of your television.

1 Plug the mains lead into an appropriate socket.

➢

The main voltage is indicated on the rear of the television

and the frequency is 50 or 60Hz.

2 Press the “ I ” button (On/Off) on the side of the television.

Result

: The Standby indicator on the side of the television

lights up.

3 Press the POWER () button on the remote control to switch the

television on.

Result

: The programme that you were watching last is re-

selected automatically.

➣

If you have not yet stored any channels, No clear picture

appears. Refer to “Storing Channels Automatically” on page

17 or “Storing Channels Manually” on page 18.

4 To switch your television off, press the “ I ”button (On/Off) again.

☛

Point the remote control at the center of the screen for

best performance.

Switching Your Television On and Off

TV

Your television can be placed in Standby mode, in order to reduce

the Power consumption.

The Standby mode can be useful when you wish to interrupt

viewing temporarily (during a meal, for example).

1 Press the POWER () button on the remote control.

Result

: The screen is turned off and the Standby indicator on

the front of the television lights.

2 To switch the television back on, simply press the POWER ()

button again or a numeric button.

➣

You can also switch on by pressing the P or button.

☛

Do not leave your television in Standby mode for long

periods of time (when you are away on holiday, for

example). Turn your television off by pressing the “

I ”

button (On/Off) on the side of the television. It is best to

unplug the set from the mains and aerial.

Placing Your Television in Standby Mode

TV

14

ENG

Becoming Familiar with the Remote Control

The remote control is used mainly to:

◆ Change channels and adjust the volume

◆ Display the on-screen menu system

The following table presents the most frequently used buttons and

their functions.

Button Viewing Function Menu Function

Used to display the next

-

stored channel.

Used to display the

-

previous stored channel.

to Used to display the corresponding channels.

➢

For double digit channels, the second digit must be

pushed immediately after the first. Failure to do this will

result in a single digit channel being displayed.

-/--

Used to select a channel numbered ten or over.

Press this button, and the “

--

” symbol is displayed.

Enter the two-digit channel number.

PRE-CH Press the PRE-CH button. The TV will switch to the last

() channel viewed.

To quickly switch between two channels that are far apart,

tune to one channel, then use the number button to select

second channel. Then, use the

PRE-CH button to quickly

alternate between them.

Used to increase the

-

volume.

Used to decrease the

-

volume.

MUTE Used to switch the sound off temporarily.

()

➣

To turn the sound back on, press this button again, or

press the or button.

MENU Used to display the Used to return to the previous

() on-screen menu system. menu or normal viewing.

-

Used to:

◆ Display a submenu

containing selections for

the current menu option

◆ Increase/decrease a

menu option value

-

Used to confirm your choice.

EXIT

-

Used to exit from the menu

() system and return to normal

viewing directly.

15

ENG

When the television is initially powered ON, several basic customer

settings proceed automatically and subsequently. The following

settings are available.

1 If the television is in Standby mode, press the POWER () button

on the remote control.

Result

: The message Plug & Play is displayed. It flickers for

a little while, and then the

Language menu is

automatically displayed.

2 Select the appropriate language by pressing the † or … button.

3 Press the ENTER () button to confirm your choice.

Result

: The message Antenna Input Check is displayed.

4 Make sure that the antenna is connected to the TV, and then

press the

ENTER () button.

Result

: The Area menu is displayed.

5 Select your area by pressing the † or … button.

6 Press the ENTER () button to confirm your choice.

Result

: The Auto Store menu is displayed.

7 To start the search, select the Start and press the ENTER ()

button.

Result

: The search will end automatically. Channels are sorted

and stored in an order which reflects their position in

the frequency range, (with lowest first and highest last).

The programme originally selected is then displayed.

➢ To stop the search before it has finished or return to normal

viewing, press the

EXIT () or ENTER () button.

8 When it has finished, the message Enjoy your watching is

displayed, and then the channel which has been stored will be

activated.

Plug & Play Feature

Plug & Play

Start

Exit

Press ENTER to start Plug & Play.

English

Français

Türkçe

Language

Move

Enter Exit

Asia/W. Europe

CIS/E. Europe

China

Hongkong/UK

Australia

NZ/Insonesia

South Africa

America

Area

Move

Enter Exit

Plug & Play

Start

Exit

Antenna Input Check

Auto Store

Start

Exit

Press ENTER to start channel store.

Channel store in process.

Storing 175MHz

18%

Auto Store

Exit

Enjoy your watching

16

ENG

If you want to reset this feature...

1 Press the MENU () button.

Result

: The main menu is displayed.

2 Press the † or … button to select Setup.

Result

: The options available in the Setup group are displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Plug & Play. Press the

ENTER () button.

Result

: The message Plug & Play is displayed.

5 For further details on how to set, refer to the opposite page.

Plug & Play Feature (continued)

Setup

Move Enter Return

Time

√√

Plug & Play

√√

Language : English

√√

Melody : Off

√√

Blue Screen : Off

√√

Film Mode : Off

√√

Image Lock

√√

TV

When you start using your television for the first time, you must

select the language which will be used for displaying menus and

indications.

1 Press the MENU ()button.

Result

: The main menu is displayed.

2 Press the † or … button to select Setup.

Result

: The options available in the Setup group are displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Language. Press the ENTER

() button.

Result

: The languages available are listed.

5 Select the appropriate language by pressing the † or … button.

6 Press the ENTER () button to confirm your choice.

7 When you are satisfied with your choice, press the EXIT ()

button to return to normal viewing.

Choosing Your Language

Setup

Time

√√

Plug & Play

√√

Language : English

√√

Melody : Off

√√

Blue Screen : Off

√√

Film Mode : Off

√√

Image Lock

√√

Setup

Time

Plug & Play

Language : English

Melody : Off

Blue Screen : On

√√

Film Mode : Off

Image Lock

TV

Move Enter Return

Englich

Français

Türkçe

TV

17

ENG

You can scan for the frequency ranges available to you, (availability

depends on your country). Automatically allocated programme

numbers may not correspond to actual or desired programme

numbers. However you can sort numbers manually and clear any

channels you do not wish to watch.

1 Press the MENU ()button.

Result

: The main menu is displayed.

2 Press the † or … button to select Channel.

Result

:

The options available in the

Channel

group are

displayed

.

3 Press the ENTER () button.

4 Press the † or … button to select Area. Press the ENTER ()

button.

Result

: The areas available are listed.

5 Select your country (or area) by pressing the † or … button.

6 Press the ENTER () button to confirm your choice

7 Press the † or … button to select Auto Store. Press the ENTER

() button.

Result

: The Auto Store menu is displayed.

8 Select the Start and press the ENTER () button to start the

search.

Result

: The search will end automatically. Channels are sorted

and stored in an order which reflects their position in

the frequency range, (with lowest first and highest last).

The programme originally selected is then displayed.

➢ To stop the search before it has finished, press the EXIT

()or ENTER () button.

9 When the channels have been stored, you can:

◆ Sort them in the order required (see page 21)

◆ Clear a channel (see page 20)

◆ Fine-tune channel reception if necessary (see page 29)

◆ Assign a name to the stored channels (see page 22)

◆ Activate/deactivate the Digital Noise Reduction feature

(see page 33)

Storing Channels Automatically

Channel

Area : Australia

√√

Auto Store

√√

Manual Store

√√

Edit

√√

Fine Tune

√√

Ch. Scan

√√

LNA : Off

√√

TV

Channel

Area : Asia/W.Europe

Auto Store

Manual Store

Edit

Fine Tune

√√

Ch. Scan

LNA : Off

TV

Channel

Area : Australia

√√

Auto Store

√√

Manual Store

√√

Edit

√√

Fine Tune

√√

Ch. Scan

√√

LNA : Off

√√

TV

Channel store in process.

Storing 175MHz

18%

Auto Store

Exit

Auto Store

Start

Return

Press ENTER to start channel store.

Move Enter Return

Asia / W. Europe

CIS / E. Europe

China

Hongkong / UK

Australia

NZ / Indonesia

South Africa

America

18

ENG

You can store up to television channels, including those received

via cable networks.

When storing channels manually, you can choose:

◆ Whether or not to store each of the channels found

◆ The programme number of each stored channel which

you wish to identify

1 Press the MENU ()button.

Result

: The main menu is displayed.

2 Press the † or … button to select Channel.

Result

:

The options available in the

Channel

group are

displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Manual Store. Press the

ENTER () button.

Result

: The Manual Store menu is displayed.

5 If necessary, select the broadcasting standard required. Press the

œ or √ button to select Color System and press the † or …

button. The colour standards are displayed in the following order.

(depending on the model).

◆

AUTO

-

PAL

-

SECAM

◆

AUTO

-

NTSC3.58

-

NTSC4.43

-

PAL60

6 Press the œ or √ button to select Sound System and press the †

or … button. The sound standards are displayed in the following

order. (depending on the model).

◆

BG

-

DK

-

I

-

M

Storing Channels Manually

Channel

Area : Asia/W.Europe

√√

Auto Store

√√

Manual Store

√√

Edit

√√

Fine Tune

√√

Ch. Scan

√√

LNA : Off

√√

TV

Manual Store

Prog. Color System Sound System

1 AUTO BG

Channel Search Store

- --

887MHz ?

Manual Store

Prog. Color System Sound System

1 AUTO BG

Channel Search Store

- --

887MHz ?

Manual Store

Prog. Color System Sound System

1 AUTO BG

Channel Search Store

- --

887MHz ?

Move Enter Return

œœ √√

Move Adjust Return

œœ √√

Move Adjust Return

œœ √√

Move Adjust Return

19

ENG

7 If you know the number of the channel to be stored, see the

following steps.

◆

Press the œ or √ button to select Channel.

◆

Press the † or … button to select C (Air channel) or S (Cable

channel).

◆

Press the √ button.

◆

Press the numeric buttons (0~9) to select indicate the required

number.

➣

If no sound or abnormal sound, re-select the sound standard

required.

8 If you do not know the channel numbers, select the Search by

pressing the

œ or √ button. Press the † or … button to start the

search.

Result

: The tuner scans the frequency range until the first

channel or the channel that you selected is received

on your screen.

9 To assign a programme number to a channel, select the Prog. by

pressing the

œ or √ button. Press the † or … button until you find

the correct number.

10 To store the channel and associated programme number, select

the

Store by pressing the œ or √ button. Press the ENTER ()

button.

Result

: The ? will be changed to OK .

11 Repeat Steps 7 to 10 for each channel to be stored.

☛

Channel mode

◆ P (Programme mode):

When completing tuning, the

broadcasting stations in your area have been assigned to

position numbers from P00 to max P99. You can select a

channel by entering the position number in this mode.

◆ C (Real channel mode):

You can select a channel by

entering the assigned number to each air broadcasting station

in this mode.

◆ S (Cable channel mode):

You can select a channel by

entering the assigned number for each cable channel in this

mode.

Storing Channels Manually (continued)

Manual Store

Prog. Color System Sound System

1 AUTO BG

Channel Search Store

C

--

887MHz ?

Manual Store

Prog. Color System Sound System

1 AUTO BG

Channel Search Store

C

--

887MHz ?

Manual Store

Prog. Color System Sound System

1 AUTO BG

Channel Search Store

C

--

887MHz OK

Manual Store

Prog. Color System Sound System

1 AUTO BG

Channel Search Store

C

--

887MHz ?

œœ √√

Move Adjust Return

0 .. 9

œœ √√

Move Adjust Return

œœ √√

Move Adjust Return

œœ √√

Move

Select

Return

20

ENG

◆ Skipping unwanted channels

You can exclude the channels of your choice from the channel

scan operation. When you scan through the stored channels,

those that you have chosen to skip are thus not displayed. All

channels that you do not specifically choose to skip are

displayed during scanning.

1 Press the MENU () button.

Result

: The main menu is displayed.

2 Press the † or … button to select Channel.

Result

: The options available in the Channel group are

displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Edit. Press the ENTER ()

button.

Result

: The Edit menu is displayed.

5 Press the † or … button to select Add/Delete. Press the ENTER

() button.

Result

: The Add/Delete menu is displayed with the current

channel automatically is selected.

6 Press the † or … button to select the channel to be deleted.

7 Press the ENTER () button to Add/Delete. To add or delete

the channel, select

Added or Deleted by pressing the † or …

button. Press the ENTER () button to confirm.

Skipping Unwanted Channels

Channel

Area : Asia/W.Europe

√√

Auto Store

√√

Manual Store

√√

Edit

√√

Fine Tune

√√

Ch. Scan

√√

LNA : Off

√√

TV

Edit

Add/Delete

√√

Sort

√√

Name

√√

Child Lock

√√

TV

Add/Delete

TV

1

-----

✽

Added

2

-----

✽

Deleted

3

-----

✽

Deleted

4

-----

✽

Deleted

5

-----

✽

Deleted

Prog.

Add/Delete

TV

1

-----

✽

Added

2

-----

✽

Deleted

3

-----

✽

Deleted

4

-----

✽

Deleted

5

-----

✽

Deleted

Prog.

Move Enter Return

Adjust Enter Return

Page is loading ...

Samsung SP-56L5HX User manual

Samsung SP-56L5HX User manual

Related papers

Other documents