Sonicare HX6807/24 User manual

Brand: Sonicare

Model: HX6807/24

Category: Electric toothbrushes

Type: User manual

ProtectiveClean

4300

English 6

简体中文

繁體中文

English

Important

Read this user manual carefully before you use the appliance and

save it for future reference.

Danger

- Keep the charger away from water. Do not place or store it over or

near water contained in a bathtub, washbasin, sink etc. Do not

immerse the charger in water or any other liquid. After cleaning,

make sure the charger is completely dry before you connect it to

the wall socket.

Warning

- The mains cord cannot be replaced. If the mains cord is damaged,

discard the charger.

- Always have the charger replaced with one of the original type in

order to avoid a hazard.

- Do not use the charger outdoors or near heated surfaces.

- If the appliance is damaged in any way (brush head, toothbrush

handle or charger), stop using it. This appliance contains no

serviceable parts. If the appliance is damaged, contact the

Consumer Care Center in your country (see chapter 'Warranty and

support').

- This appliance can be used by children and persons with reduced

physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the

hazards involved. Cleaning and user maintenance shall not be

made by children without supervision.

- Children shall not play with the appliance.

Caution

- Do not clean the brush head, the handle or the charger in the

dishwasher.

- If you have had oral or gum surgery in the previous 2 months,

consult your dentist before you use the toothbrush.

English

- Consult your dentist if excessive bleeding occurs after using this

toothbrush or if bleeding continues to occur after 1 week of use.

Also consult your dentist if you experience discomfort or pain

when you use the Philips Sonicare.

- The Philips Sonicare toothbrush complies with the safety

standards for electromagnetic devices. If you have a pacemaker or

other implanted device, contact your physician or the device

manufacturer of the implanted device prior to use.

- If you have medical concerns, consult your doctor before you use

the Philips Sonicare.

- This appliance has only been designed for cleaning teeth, gums

and tongue. Do not use it for any other purpose. Stop using the

appliance and contact your doctor if you experience any

discomfort or pain.

- The Philips Sonicare toothbrush is a personal care device and is

not intended for use on multiple patients in a dental practice or

institution.

- Stop using a brush head with crushed or bent bristles. Replace the

brush head every 3 months or sooner if signs of wear appear. Do

not use other brush heads than the ones recommended by the

manufacturer.

- If your toothpaste contains peroxide, baking soda or bicarbonate

(common in whitening toothpastes), thoroughly clean the brush

head with soap and water after each use. This prevents possible

cracking of the plastic.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable standards and

regulations regarding exposure to electromagnetic fields.

Radio Equipment Directive

- Radio Equipment in this product operates at 13.56 MHz

- Maximum RF power transmitted by the Radio Equipment is

30.16dBm

English

Introduction

Congratulations on your purchase and welcome to Philips! To fully

benefit from the support that Philips offers, register your product at

www.philips.com/welcome.

Your Philips Sonicare (Fig. 1)

1 Hygienic travel cap

2 Smart brush head(s)*

3 Handle

4 Power on/off button

5 Brush head replacement reminder light

6 Battery indication

7 Charging base

8 Travel case (specific types only)*

*Note: The content of the box may vary based on the model

purchased.

Brush heads

Your Philips Sonicare comes with one or more brush heads which are

designed to deliver superior results for your oral care needs.

Philips Sonicare BrushSync Technology

Your smart brush heads use a microchip to sync with your handle,

enabling brush head replacement reminder. For more information

regarding the brush head replacement reminder, see 'Features'.

This symbol indicates the brush head is equipped with BrushSync

technology. (Fig. 2)

Brushing modes

Your power toothbrush is equipped with clean mode.

Clean mode

Clean is a 2-minute mode. It gives you a thorough and complete

clean and is recommended to be used with the C2 Optimal Plaque

Control brush head.

English

Intensities

Your power toothbrush gives you the option to choose between low

and high intensity.

Note: When you use the toothbrush for the first time, the default

setting is the low intensity.

- Press the power button once to turn on the toothbrush.

- Press a second time within 2 seconds to change the intensity.

- Press a third time within 2 seconds to pause.

After 2 seconds of brushing, pressing the power button again will also

pause the toothbrush.

Using your Philips Sonicare

Brushing instructions

1 Press the brush head onto the handle in such a way that the

bristles will face the front of the handle. (Fig. 3)

2 Firmly press the brush head down onto the metal shaft until it

stops.

Note: It is normal to see a slight gap between the brush head and

the handle.

3 Wet the bristles. (Fig. 4)

4 Apply a small amount of toothpaste on the bristles. (Fig. 5)

5 Place the toothbrush bristles against the teeth at a slight angle (45

degrees), pressing firmly to make the bristles reach the gumline or

slightly beneath the gumline. (Fig. 6) A change in vibration (and a

slight change in sound) alerts you when you apply too much

pressure while brushing.

Note: Keep the center of the brush in contact with the teeth at all

times.

6 Press the power on/off button to turn on the Philips Sonicare. (Fig.

7 Gently keep the bristles placed on the teeth and in the gumline.

Brush your teeth with small back and forth motion so the bristles

reach between the teeth. (Fig. 8)

English

Note: The bristles should slightly flare. Do not scrub.

8 To clean the inside surfaces of the front teeth, tilt the brush handle

semi-upright and make several vertical overlapping brushing

strokes on each tooth. (Fig. 9)

9 To make sure you brush evenly throughout the mouth, divide the

mouth into 4 sections using the Quadpacer feature. (Fig. 10) The

quadpacer feature beeps after 30 seconds.

10 Brush for the full 2 minutes following the Quadpacer. (Fig. 11) After

2 minutes, the toothbrush will automatically shut off.

- After you have completed the brushing cycle, you can spend

additional time brushing the chewing surfaces of your teeth and

areas where staining occurs. (Fig. 12)

Your Philips Sonicare toothbrush is safe to use on:

- Braces (brush heads wear out sooner when used on braces)

- Dental restorations (fillings, crowns, veneers)

Note: When the Philips Sonicare toothbrush is used in clinical studies,

it must be used in the Clean mode (for plaque and gum health claims)

with EasyStart turned off.

Features

- EasyStart

- Brush head replacement reminder

- Pressure sensor

- Quadpacer

EasyStart

This Philips Sonicare model comes with the EasyStart feature

deactivated. The EasyStart feature gently increases the power over

the first 14 brushings to help you get used to the brushing with the

Philips Sonicare.

To activate EasyStart see 'Activating or deactivating features'.

Brush head replacement reminder

Your Philips Sonicare is equipped with BrushSync technology that

tracks the wear of your brush head. (Fig. 13)

English

1 When attaching a new smart brush head for the first time the

brush head replacement reminder light blinks green three times.

This confirms you have a Philips brush head with BrushSync

technology.

2 Over time, based on the pressure you apply and the amount of

time used, the handle will track brush head wear in order to

determine the optimal time to change your brush head. This

feature gives you the guarantee for the best cleaning and care of

your teeth.

3 When the brush head replacement reminder light lights up amber,

you should replace your brush head.

To deactivate the brush head replacement reminder see 'Activating or

deactivating features'.

Pressure sensor

Your Philips Sonicare is equipped with an advanced sensor that

measures the pressure you apply while brushing. If you apply too

much pressure, the toothbrush will provide immediate feedback to

indicate that you need to reduce the pressure. This feedback is given

by a change in vibration and therefore brushing sensation.

To deactivate the pressure sensor see 'Activating or deactivating

features'.

Quadpacer

The Quadpacer is an interval timer that has a short beep and pause

to remind you to brush the different sections of your mouth.

Depending on the brushing mode you have selected (see 'Brushing

modes'), the Quadpacer beeps at different intervals during the

brushing cycle.

Activating or deactivating features

You can activate or deactivate the following features of your

toothbrush:

- EasyStart

- Brush head replacement reminder

- Pressure sensor

English

To activate or deactivate these features, follow the instructions

below:

EasyStart

1 Put the handle on the plugged-in charger.

2 Press and hold the power on/off button while the handle remains

on the charger.

3 Keep the power on/off button pressed until you hear a single

short beep (after 2 seconds).

4 Release the power on/off button.

Triple tone of low-med-high means the EasyStart feature has

been activated. The brush head replacement light and battery

light will also blink green 3 times in unison to confirm activation.

Triple tone of high-med-low means the EasyStart feature has

been deactivated. The brush head replacement light and

battery light will also blink amber 3 times in unison to confirm

deactivation.

Note: To achieve clinical efficacy, EasyStart needs to be deactivated.

Brush head replacement reminder

1 Put the handle on the plugged-in charger.

2 Press and hold the power on/off button while the handle remains

on the charger.

3 Keep the power on/off button pressed until you hear a series of

two short beeps (after 4-5 seconds).

4 Release the power on/off button.

Triple tone of low-med-high means the Brush head

replacement reminder feature has been activated. The brush

head replacement light and battery light will also blink green 3

times in unison to confirm activation.

Triple tone of high-med-low means the Brush head

replacement reminder feature has been deactivated. The brush

head replacement light and battery light will also blink amber 3

times in unison to confirm deactivation.

English

Pressure sensor

1 Put the handle on the plugged-in charger.

2 Press and hold the power on/off button while the handle remains

on the charger.

3 Keep the power on/off button pressed until you hear a series of

three short beeps (after 6-7 seconds).

4 Release the power on/off button.

Triple tone of low-med-high means the pressure sensor feature

has been activated. The brush head replacement light and

battery light will also blink green 3 times in unison to confirm

activation.

Triple tone of high-med-low means the pressure sensor feature

has been deactivated. The brush head replacement light and

battery light will also blink amber 3 times in unison to confirm

deactivation.

If you continue holding the power on/off button after the three short

beeps, the activate/deactivate sequence repeats.

Battery status and charging

1 Put the plug of the charger in an electrical outlet.

2 Place the handle on the charger.

The charger will emit 2 short beeps to confirm that the handle is

placed properly.

The flashing light of the battery level indicator shows that the

toothbrush is charging.

When handle is fully charged on the charger, the battery light

shows solid green for 30 seconds and switches off.

Note: Your toothbrush comes pre-charged for first use. After first use,

charge for at least 24 hours.

Battery status (when handle is not on charger)

When removing the Philips Sonicare from the charger, the battery

light at the bottom of the toothbrush will indicate the status of the

battery life.

English

- Solid green LED: full battery

- Flashing green LED: medium battery

- Flashing amber LED and three beeps: low battery

- Flashing amber LED and two sets of five beeps: No brushing

sessions left (charge toothbrush)

Cleaning

Note: Do not clean the brush head, handle or travel case in the

dishwasher.

Toothbrush handle

1 Remove the brush head and rinse the metal shaft area with warm

water. Make sure you remove any residual toothpaste (Fig. 14).

Note: Do not push on the rubber seal on the metal shaft with

sharp objects, as this may cause damage.

2 Wipe the entire surface of the handle with a damp cloth.

Note: Do not use isopropyl rubbing alcohol, vinegar or bleach to

clean handle as this may cause discoloration.

Brush head

1 Rinse the brush head and bristles after each use (Fig. 15).

2 Remove the brush head from the handle and rinse the brush head

connection with warm water at least once a week.

Charger

1 Unplug the charger before you clean it.

2 Wipe the surface of the charger with a damp cloth.

Storage

If you are not going to use your Philips Sonicare for an extended

period of time, unplug the charger from the wall socket, clean it and

store it in a cool and dry place away from direct sunlight.

Locating the model number

Look on the bottom of the Philips Sonicare toothbrush handle for the

model number (HX681x).

English

Recycling

- Do not throw away the product with the normal household waste

at the end of its life, but hand it in at an official collection point for

recycling. By doing this, you help to preserve the environment.

- This product contains a built-in rechargeable battery which shall

not be disposed of with normal household waste. Please take your

product to an official collection point or a Philips service center to

have a professional remove the rechargeable battery.

- Follow your country’s rules for the separate collection of electrical

and electronic products and rechargeable batteries. Correct

disposal helps prevent negative consequences for the

environment and human health.

Removing the rechargeable battery

Warning: Only remove the rechargeable battery when you discard the

appliance. Make sure the battery is completely empty when you

remove it.

To remove the rechargeable battery, you need a towel or cloth, a

hammer and a flat-head (standard) screwdriver. Observe basic safety

precautions when you follow the procedure outlined below. Be sure

to protect your eyes, hands, fingers, and the surface on which you

work.

1 To deplete the rechargeable battery of any charge, remove the

handle from the charger, turn on the Philips Sonicare and let it run

until it stops. Repeat this step until you can no longer turn on the

Philips Sonicare.

2 Remove and discard the brush head. Cover the entire handle with

a towel or cloth (Fig. 16).

3 Hold the top of the handle with one hand and strike the handle

housing 0.5 inch above the bottom end. Strike firmly with a

hammer on all 4 sides to eject the end cap (Fig. 17).

Note: You may have to hit on the end several times to break the

internal snap connections.

4 Remove the end cap from the toothbrush handle. If the end cap

does not release easily from the housing, repeat step 3 until the

end cap is released (Fig. 18).

English

5 Holding the handle upside down, press the shaft down on a hard

surface. If the internal components do not easily release from the

housing, repeat step 3 until the internal components are released

(Fig. 19).

6 Remove the rubber battery cover.

7 Wedge the screwdriver between the battery and the black frame

at the bottom of the internal components. Then pry the

screwdriver away from the battery to break the bottom of the

black frame (Fig. 20).

8 Insert the screwdriver between the bottom of the battery and the

black frame to break the metal tab connecting the battery to the

green printed circuit board. This will release the bottom end of the

battery from the frame (Fig. 21).

9 Grab the battery and pull it away from the internal components to

break the second metal battery tab (Fig. 22).

Caution: Be aware of the sharp edges of the battery tabs so as to

avoid injury to your fingers.

10 Cover the battery contacts with tape to prevent any electrical short

from residual battery charge. The rechargeable battery can now be

recycled and the rest of the product discarded appropriately (Fig.

23).

Warranty and support

If you need information or support, please visit

www.philips.com/support or read the international warranty leaflet.

Warranty restrictions

The terms of the international warranty do not cover the following:

- Brush heads.

- Damage caused by use of unauthorized replacement parts.

- Damage caused by misuse, abuse, neglect, alterations or

unauthorized repair.

- Normal wear and tear, including chips, scratches, abrasions,

discoloration or fading.

English

注意事项

使用本产品之前，请仔细阅读本使用说明书，并妥善保管以备日后参考。

危险

- 使充电器远离水源。切勿将它放置或存放在任何有水的容器的上方或附

近，如：浴盆、脸盆、水池等。切勿将充电器浸入水或任何其他液体

中。清洁后，确保充电器完全干燥，再将其连接至电源。

- 必须安装需要的固定部件，以免它们掉入水中。

警告

- 不得更换电源线。如果电源线损坏，请丢弃充电器。

- 应始终使用原装型号的充电器进行更换，以免发生危险。

- 切勿在户外或高温表面附近使用充电器。

- 如果本产品受到任何损坏（刷头、牙刷手柄或充电器），请停止使用。

本产品不包含任何可维修零部件。如果本产品已损坏，请联系您所在国

家/地区的客户服务中心（请参阅“保修和支持”一章）。

- 本产品适合由儿童和肢体不健全、感觉或精神上有障碍或缺乏相关经验

和知识的人士使用，但前提是有人对他们使用本产品进行监督或指导，

以确保他们安全使用，并且让他们明白相关的危害。不要让儿童在无人

监督的情况下对本产品进行清洁和保养。

- 切勿让儿童玩弄本产品。

警告

- 请勿在洗碗机中清洗牙刷头、牙刷柄或充电器。

- 如果您在前 2 个月中曾做过口腔或牙龈手术，请在使用本产品前先咨询

您的牙医。

- 如果使用本产品后牙龈大量出血或在使用 1 周后仍会出血，请咨询您的

牙医。如果使用飞利浦 Sonicare 时感觉不适或疼痛，也请咨询您的牙

医。

- 飞利浦 Sonicare 牙刷符合电磁装置的安全标准。有关任何涉及心脏起

搏器或其他植入装置的问题，请在使用之前咨询医生或相关植入装置的

设备制造商。

- 如果您有医学问题，请在使用飞利浦 Sonicare 前咨询医生。

- 本产品设计仅用于清洁牙齿、牙龈和舌头。请勿将其用作任何其它用

途。如果感觉任何不适或疼痛，请停止使用本产品并与医生联系。

- 飞利浦 Sonicare 牙刷为私人用品，不可供牙医诊所或机构对多位患者使

用。

简体中文

- 请停止使用变形或刷毛弯曲的牙刷头。请每 3 个月更换一次牙刷头，如

果出现磨损迹象，应提前更换。切勿使用非制造商推荐的其他刷头。

- 如果您所用的牙膏中含有过氧化物、碳酸氢钠或其它重碳酸盐（增白牙

膏中的常见成份），则请务必在每次使用后用肥皂和水彻底清洗刷头。

这可以预防可能出现的塑料破裂。

电磁场 (EMF)

本飞利浦产品符合所有有关暴露于电磁场的适用标准和法规。

无线电设备指令

- 本产品中无线电设备的工作频率为 13.56 MHz。

- 无线电设备传输的最大射频功率为 30.16 dBm

简介

感谢您的惠顾，欢迎光临飞利浦！为了让您能充分享受飞利浦提供的支

持，请在 www.philips.com/welcome 上注册您的产品。

飞利浦 Sonicare 声波震动牙刷（图 1）

1 旅行用卫生保护盖

2 智能刷头*

3 牙刷手柄

4 开/关按钮

5 刷头更换指示灯

6 电量指示灯

7 充电座

8 旅行收纳盒（仅限于特定型号）*

*注意：包装盒内物品可能会因所购买型号而异。

刷头

飞利浦 Sonicare 声波震动牙刷配有一个或多个刷头，旨在提供更好的口腔

护理效果，满足您的需求。

飞利浦 Sonicare 声波震动牙刷 BrushSync (RFID无线识别）技术

您的智能刷头使用RFID 微芯片与您的牙刷柄同步，可启用刷头更换指示

灯。有关刷头更换提醒的详细信息，请参阅“功能”。

此符号表示刷头采用了 BrushSync ( RFID 无线识别) 技术 (图 2)

简体中文

刷牙模式

您的电动牙刷具有清洁模式。

清洁模式

清洁模式时长 2 分钟。该模式可提供全面彻底的清洁，建议与牙菌斑清除

型 (C2) 刷头配合使用。

强度

这款电动牙刷可供您自由选择低强度和高强度设置：

注意：首次使用牙刷时，默认设置为低强度。

- 按一下开关按钮打开 Sonicare 声波震动牙刷。

在 2 秒内再按一次开关按钮可改变强度。

在 2 秒内按第三次开关按钮可以暂停。

刷牙 2 秒后，再次按电源按钮也将使牙刷暂停工作。

使用飞利浦 Sonicare 声波震动牙刷

刷牙说明

1 按照刷毛朝向牙刷柄 (图 3)正面的方式，将刷头按进牙刷柄。

2 用力将牙刷头向下按到金属轴上，直到按不动为止。

注意：刷头与刷柄之间会有小间隙，这是正常的。

3 浸湿刷毛 (图 4)。

4 在刷毛 (图 5)上挤少量牙膏。

5 将牙刷的刷毛以小角度（45 度）放在牙齿上，用力按下以使刷毛接触牙

龈或牙龈 (图 6)略下方。当刷牙太过用力时，将出现振动变化（和声音

细微变化）来提示您。

注意：始终将牙刷中间与牙齿接触。

6 按电源开/关按钮打开飞利浦 Sonicare 声波震动牙刷 (图 7)。

7 将刷毛轻轻放置于牙齿和牙龈上，来回小幅度缓慢移动，这样可以让刷

毛刷到牙 (图 8)缝。

注意：刷毛应稍微呈喇叭形，请勿过度用力。

8 要清洁门牙内表面，请将牙刷柄呈半直立状倾斜，在每颗牙齿 (图 9)上

反复垂直震动。

简体中文

9 为确保牙刷能均匀清洁整个口腔，可使用 Quadpacer 30 秒时段计时器

功能 (图 10)将口腔分为 4 个区域。 Quadpacer 功能将在 30 秒后，发

出蜂鸣音。

10 在 Quadpacer 30 秒时段计时器 (图 11)发出蜂鸣音之后，共有 2 分钟刷

牙时间。 2 分钟之后，牙刷会自动关闭。

- 在完成刷牙周期之后，您可以多花一些时间刷洗牙齿的咀嚼面以及污垢

容易出现 (图 12)的区域。

您的飞利浦 Sonicare 声波震动牙刷可安全用于：

- 牙齿矫正器（在牙齿矫正器上使用时，牙刷头磨损较快）

- 修复牙体（补牙、齿冠、烤瓷牙)

注意：飞利浦 Sonicare 声波震动牙刷用于临床研究时，必须使用清洁模式

（适用于去除牙菌斑和牙龈保健需求），同时关闭 EasyStart 刷牙动力增强

程序。

功能

- EasyStart 刷牙动力增强程序

- 刷头更换指示灯

- 压力传感器

- Quadpacer 30 秒时段计时器

EasyStart 刷牙动力增强程序

本型号的飞利浦 Sonicare 声波震动牙刷出厂时未启用 EasyStart 刷牙动力

增强程序。 EasyStart 刷牙动力增强程序功能在前 14 次刷牙时会缓慢增加

动力，以帮助您适应使用飞利浦 Sonicare 声波震动牙刷刷牙。

要启用 EasyStart 刷牙动力增强程序，请参见“启用或禁用功能”。

刷头更换指示灯

这款飞利浦 Sonicare 声波震动牙刷配备有 BrushSync (RFID无线识别）技

术，可跟踪刷头 (图 13)的使用情况。

1 当首次安装新的智能刷头时，刷头更换指示灯将呈绿色闪烁三次。此状

态表示您的飞利浦刷头配备了 BrushSync (RFID无线识别）技术。

2 随着时间的推移，根据您施加的力度和使用的时间，牙刷柄将跟踪刷头

磨损情况，以确定更换刷头的最佳时间。此功能可确保您的牙齿获得更

好的清洁与护理。

3 当刷头更换指示灯呈琥珀色亮起时，您便应当更换刷头了。

简体中文

Page is loading ...

Sonicare HX6807/24 User manual

Brand: Sonicare

Model: HX6807/24

Category: Electric toothbrushes

Type: User manual

Download PDF

report

Sonicare HX6807/24 User manual

Sonicare HX6807/24 User manual

Related papers

Other documents