Sonicare HX9903/03 User manual

Typenummer

DiamondClean

Smart

m

on

dCl

ean

a

rt

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 1 13/02/17 16:38

Page is loading ...

IMPORTANT

SAFEGUARDS

Warning: READ ALL INSTRUCTIONS

BEFORE USE

When using electrical products, especially when

children are present, basic safety precautions

should always be followed, including the following:

DANGERS

To reduce the risk of electrocution:

1 Always place and store the charger at a safe

distance from water.

2 Do not reach for a product that has fallen into

water. Unplug immediately.

3 Never use a charger with a damaged cord or

plug.

WARNINGS

To reduce the risk of burns, electrocution, re or

physical injury:

1 Do not use attachments other than those

recommended by the manufacturer.

2 Do not plug into an outlet with a voltage other

than specied on the bottom of the product.

This product is designed to operate within a

range of 100 to 240 volts. Voltage converters do

not warrant voltage compatibility.

3

Never force the plug into an outlet; if the plug

does not easily t into the outlet, discontinue use.

4 Discontinue use if the product appears

damaged in any way (brush head, handle or

charger, etc.).

6

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 6 13/02/17 16:38

5 The mains cord cannot be replaced. If the mains

cord is damaged, discard the charger.

6 Keep the cord away from heated surfaces.

7 Do not use the base charger outdoors or near

heated surfaces.

8 This product contains no user-serviceable parts.

Refer to ‘Warranty and support’ if the product

no longer works properly or needs repair.

9 Use this product only for its intended use as

described in this document or as recommended

by your dental professional.

10 This product is not intended for use by

persons (including children) with reduced

physical, sensory, or mental capabilities, or

lack of experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety.

11 Children should be supervised to ensure that

they do not play with the product.

12 Philips Sonicare is a personal care device and

is not intended for use on multiple patients in a

dental oce or institution.

13 Use UL Listed computer, USB Hub or USB

duplex receptacle when charging the

toothbrush handle in the travel case.

14 When using a computer to recharge the

toothbrush handle, the computer should be

located away from sources of water

(i.e. sink or tub) so as to avoid electrical shock.

15 In order to eectively charge your Philips

Sonicare do not place your charger base on a

magnetic metal surface.

7

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 7 13/02/17 16:38

16 The product is not intended to be repaired

by service personnel in case of failure or

component defect (unit can be thrown away).

17 For connection to a supply not in the U.S.A., use

a charger of the proper conguration for the

power outlet.

18 Use this product only for its intended use

as described in this manual. Do not use

attachments not recommended by the

manufacturer.

MEDICAL WARNINGS

1 Consult your dental professional before you

use this product if you have had oral or gum

surgery in the previous 2 months.

2 Contact your dental professional if excessive

bleeding occurs after using this product or

bleeding continues to occur after 1 week of use.

3 Discontinue use of this product and contact

a physician/dentist if discomfort or pain is

experienced.

4 This product complies with the safety standards

for electromagnetic devices. If you have a

pacemaker or other implanted device, contact

your physician or the device manufacturer prior

to use.

5 Consult your physician if you have other

medical concerns.

Electromagnetic elds (EMF)

This Philips device complies with all applicable

standards and regulations regarding exposure to

electromagnetic elds.

SAVE THESE

INSTRUCTIONS

8

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 8 13/02/17 16:38

Radio Equipment Directive

- Radio Equipment in this product operates

between 2402 – 2480 MHz

- Maximum RF power transmitted by the Radio

Equipment is +3 dBm

Introduction

Congratulations on your purchase and welcome

to Philips! To fully benet from the support that

Philips oers, register your product at

www.philips.com/welcome or via the Philips

Sonicare app.

Your Philips Sonicare (Fig. 1)

1 Hygienic travel cap

2 Brush heads

3 Handle

4 Power on/o button

5 Intensity light

6 Mode/intensity button

7 Mode light

8 Brush head replacement reminder light

9 Battery indication

10 Light ring

11 Charging base

12 Travel case

13 Cord storage compartment

14 USB cord (integrated)

15 Charging glass

Note: The content of the box may vary based on

the model purchased.

Brush heads

Your Philips Sonicare comes with a range of brush

heads which are designed to deliver superior

results for your oral care needs.

9

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 9 13/02/17 16:38

The number and type of brush heads might

change according to the toothbrush type you

purchased.

1 Premium Plaque Control brush head

2 Premium Gum Care brush head

3 Premium White brush head

4 Tongue Care+ brush head (specic types only)

Smart brush head recognition

Premium Plaque Control, Premium Gum Care,

Premium White and Tongue Care+ brush heads

are enabled with smart brush head recognition

technology.

A micro-chip inside the brush head communicates

with the toothbrush handle. So when you attach a

brush head, the handle automatically recognizes

the brush head and selects the recommended

mode and intensity level to optimize your brushing

performance.

Thanks to this feature the toothbrush also tracks

your usage and gives a personalized reminder

when you need to replace your brush head for the

best oral care results.

Brushing modes

Your power toothbrush is equipped with 5 dierent

modes to accommodate all your oral care needs

(some models come with 4 brushing modes only).

The following modes are available:

10

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 10 13/02/17 16:38

Clean mode

Clean is a 2-minute mode, recommended to be

used with intensity level 3. It gives you a thorough

and complete clean and is recommended to be

used with the Premium Plaque Control brush

head. In order to reach optimal results, follow the

instructions below.

1

Begin brushing the upper right teeth (segment 1)

and brush for 20 seconds, on both the outer and

inner surfaces, before you move to the upper

front teeth (segment 2). Continue doing this for

segments 3 to 6 to ensure even brushing in all

6 segments of the mouth. You will hear a beep

after each 20-second interval, to indicate that you

should move to the next segment.

White+ mode

White+ is a 2-minute 40-seconds mode,

recommended to be used with intensity level

3 and the Premium White brush head. In order

to reach optimal results, follow the instructions

below.

1 Begin brushing the upper right teeth (segment

1) and brush for 20 seconds before you move

to the upper front teeth (segment 2). Continue

doing this for segments 3 to 6 to ensure even

brushing in all 6 sections of the mouth.

2 After completing all 6 of these segments,

the toothbrush switches to polishing mode

automatically.

2

13

64

5

2

13

64

5

11

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 11 13/02/17 16:38

3 To polish your teeth, brush the outer surface of

your upper teeth for 20 seconds (segment 2)

and then brush the outer surface of your lower

teeth for 20 seconds (segment 5). The polishing

motion used in this part of the mode will feel

and sound dierent from the rst two minutes

of the mode.

Gum Health mode

Gum Health is a 3-minute 20-seconds mode,

recommended to be used with intensity level 3

and the Premium Gum Care brush head. In order

to reach optimal results, follow the instructions

below:

1

Begin brushing the upper right teeth (segment 1)

and brush for 20 seconds, on both the outer and

inner surfaces, before you move to the upper

front teeth (segment 2). Continue doing this for

section 3 to 6 to ensure even brushing in all 6

segments of the mouth.

2

Next, to take optimal care for your gums, brush the

outer and inner surfaces of your upper right back

teeth for 20 seconds (segment 1), then brush the

outer and inner surfaces of your upper left back

teeth for 20 seconds (segment 3).

Continue brushing the outer and inner surfaces

of your lower right back teeth for 20 seconds

(segment 4), followed by another 20 seconds

on the outer and inner surfaces of your lower

left back teeth (segment 6). The brushing

motion used in this part of the mode will feel

and sound dierent from the rst two minutes

of the mode.

2

5

2

13

64

5

13

64

12

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 12 13/02/17 16:38

DeepClean+ mode

DeepClean+ mode length depends on whether

or not the handle is connected to the app. In

connected mode DeepClean+ runs for two

minutes and provides BrushPacer feedback every

20 seconds. In non-connected mode DeepClean+

runs for three minutes and provides BrushPacer

feedback every 30 seconds. In order to reach

optimal results, follow the instructions below when

brushing non-connected.

- Begin brushing in the upper right teeth

(segment 1) and brush for 30 seconds, on both

the outer and inner surfaces, before you move

to the upper front teeth (segment 2). Continue

doing this for segments 3 to 6 to ensure even

brushing in all 6 segments of the mouth.

Tongue Care mode (specic types only)

Tongue Care is a 20-second mode, recommended

to be used with intensity level 1 and the Tongue

Care+ brush head. In order to reach optimal results,

follow the instructions below:

2

13

64

5

13

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 13 13/02/17 16:38

1 Wet the micro bristles and brush your tongue

with a back and forth motion. Clean as far back

as comfortable.

2 Rinse your mouth and repeat the procedure

two more times.

Based on the brush head you attach, the mode will

be selected automatically. If you want to adjust

the mode or intensity manually, you can do this by

using the mode/intensity button. Press the mode/

intensity button before brushing to change the

mode, and press it while brushing to adjust the

intensity level. Your selection will be remembered

next time you attached the same brush head. If

you want to go back to the initial recommended

settings for your brush head, manually change it to

the recommended setting described above.

Note: When the Philips Sonicare is used in clinical

studies, it must be used at high intensity in the

Clean mode, in White+ mode, in GumHealth mode,

or in unconnected DeepClean+ mode to achieve

the ecacy in plaque removal, stain removal, gum

health or superiority (respectively).

Intensity settings

Your power toothbrush gives you the option to

choose between 3 dierent intensity levels: low,

medium and high. Based on the brush head you

attach, the intensity will be selected automatically.

If you wish to change to a dierent intensity,

you can do so by pressing the mode/intensity

button while brushing. For optimal results it is

recommended to use the automatically selected

intensity. The intensity cannot be changed as long

as the handle is powered o or paused.

20 sec.

14

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 14 13/02/17 16:38

Using your Philips Sonicare

Brushing instructions

1 Attach your desired brush head (see 'Brush

heads'). Align the brush head so the bristles

point in the same direction as the front of the

handle.

2 Wet the bristles.

3 Apply a small amount of toothpaste on the

bristles.

4 Place the toothbrush bristles against the teeth

at a slight angle (45 degrees), pressing rmly to

make the bristles reach the gumline or slightly

beneath the gumline. A change in vibration (and

a slight change in sound) and activation of the

light ring alert you when you apply too much

pressure while brushing.

Note: Keep the center of the brush in contact

with the teeth at all times.

15

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 15 13/02/17 16:38

5 Press the power on/o button to switch on the

Philips Sonicare.

6 Apply light pressure to maximize Philips

Sonicare's eectiveness. Brush your teeth with

a small back and forth motion so the bristles

reach between the teeth. Continue this motion

throughout the brushing cycle.

Note: The bristles should are slightly. Do not

scrub.

7 To clean the inside surfaces of the front teeth,

tilt the brush handle semi-upright and make

several vertical overlapping brushing strokes on

each tooth.

Your Philips Sonicare is safe to use on:

- Braces (brush heads wear out sooner when

used on braces).

- Dental restorations (llings, crowns, veneers).

Features and accessories

a App

b Pressure sensor

c Brush head replacement reminder

d BrushPacer

e Easy-start

f Travel case (specic types only)

g Brush head holder (specic types only)

16

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 16 13/02/17 16:38

a. App

Your Philips Sonicare is Bluetooth enabled and

allows you to achieve superior oral health care

with the Philips Sonicare app.

Using the Philips Sonicare app will help you to

improve your oral health care habits. It gives you

real-time feedback while brushing, informs you if

you missed any spots when brushing, tracks your

brushing behavior over time and provides useful

tips and tricks for your healthiest mouth ever. In

order to fully benet from your Philips Sonicare,

we advise you to follow these steps:

Connecting your toothbrush

1 Download the Philips Sonicare app from the

Apple App Store or Google Play Store.

2 Conrm Bluetooth is switched on on your

mobile device before you open the app. Check

the settings on your mobile device to switch on

Bluetooth.

3 Open the Sonicare app.

4 To connect the toothbrush to the app, remove

the handle from the charger and press the

mode/intensity button.

5 Follow the Sonicare app instructions displayed

on your mobile device. The app automatically

connects with the toothbrush. If the toothbrush

does not connect, follow the troubleshooting

steps provided in the app.

Note: For optimal data capture, keep your mobile

device close during brushing.

17

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 17 13/02/17 16:38

b. Pressure sensor

Your Philips Sonicare is equipped with an

advanced sensor that measures the pressure

you apply while brushing. If you apply too much

pressure, the toothbrush will provide immediate

feedback to indicate that you need to reduce the

pressure. The feedback is given in two dierent

ways:

1 You experience a change in vibration and

therefore brushing sensation.

2 The pressure warning light of the light ring will

light up purple.

If you receive a warning, reduce the pressure. The

light will turn o and the brushing sensation will

adjust to the original sensation.

Activating or deactivating the pressure

sensor

1 Place the handle, with a brush head attached,

in the plugged-in charger.

2 Pressure sensor is enabled by holding the

mode/intensity button and by pressing the

power button twice while on a charger. The

handle will beep twice to conrm it is enabled.

3 Pressure sensor is disabled by holding the

mode/intensity button and by pressing the

power button twice while on a charger. The

handle will beep once to conrm it is disabled.

18

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 18 13/02/17 16:38

c. Brush head replacement reminder

Your Philips Sonicare is equipped with a smart

feature that tracks the wear of your brush head.

Depending on the pressure you apply and the

amount of time used, the brush head replacement

reminder light reminds you to change your brush

head. It is important to change your brush head in

time in order to guarantee the best cleaning & care

of your teeth.

When the amber brush head replacement light

starts blinking, you should replace your brush

head.

Activating or deactivating the brush head

replacement reminder

1 Place the handle in the plugged-in charger.

2 Brush head replacement reminder is enabled

by holding the mode/intensity button and by

pressing the power button three times while

on the charger. The handle will beep twice to

conrm it is enabled.

3 Brush head replacement reminder is disabled

by holding the mode/intensity button and by

pressing the power button three times while

on the charger. The handle will beep once to

conrm it is disabled.

d. BrushPacer

The BrushPacer is an interval timer that has a

short beep and pause to remind you to brush the

dierent sections of your mouth. Depending on the

brushing mode you have selected (see 'Brushing

modes'), the BrushPacer beeps at dierent

intervals during the brushing cycle.

2

3 1

64

5

19

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 19 13/02/17 16:38

e. Easy-start

The Easy-start feature gently increases the power

over the rst 14 brushings to help you get used

to the brushing with the Philips Sonicare. The

Easy-start feature works in all modes other than

TongueCare+ mode. This Philips Sonicare model

comes with the Easy-start feature deactivated.

Activating or deactivating the Easy-start

feature

1 Place the handle in the plugged-in charger.

2 Easy-start is enabled by holding the mode/

intensity button and by pressing the power

button once while on the charger. The handle

will beep twice to conrm it is enabled.

3 Easy start is disabled by holding the mode/

intensity button and by pressing the power

button once while on the charger. The handle

will beep once to conrm it is disabled.

Note: Using the Easy-start feature beyond the

initial ramp-up period is not recommended and

reduces Philips Sonicare eectiveness in removing

plaque.

Note: Each of the rst 14 brushings must be at least

1 minute in length to properly move through the

Easy-start ramp-up cycle.

Note: To achieve clinical ecacy, Easy-start needs

to be deactivated.

20

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 20 13/02/17 16:38

f. Travel case (specic types only)

Your Philips Sonicare comes with a travel case to

make traveling with your power toothbrush more

convenient. It is designed to accommodate the

power toothbrush handle and two brush heads.

Some models come with a USB charging travel

case which connects to your laptop via USB -this

allows you to charge your Philips Sonicare when

traveling. For information about charging your

Philips Sonicare with the travel case, see ‚Battery

status and charging‘.

Battery status and charging

Charging with glass (specic types only)

1 Plug the charging base into a wall socket.

2 Place the charging glass on top of the charging

base and place the handle in the glass.

The charging indicator ashes white until your

toothbrush is fully charged.

Charging with travel case (specic types only)

1 Place the handle in the charging travel case.

2 Connect the charging travel case to a UL

60950-1 and IEC 60950-1 Listed computer,

laptop, USB hub, USB receptacle, or wall

adapter. The USB cord is attached to the

travel case and stored in the cord storage

compartment.

3 The wall adapter shall have an output marked

Class 2 or the limited power source (LPS)

requirements and compatible with the electrical

ratings marked on the travel case.

4 The battery indication ashes white until your

toothbrush is fully charged.

21

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 21 13/02/17 16:38

Important: The wall adapter must be a safe extra

low voltage source, compatible with the electrical

ratings marked on the device.

Important: Only toothbrush models HX993W,

HX993B, HX993P, HX993S, HX993L can be

charged in the travel case. Other products and

batteries are not compatible with the travel case.

Note: It takes at least 24 hours to fully charge your

Philips Sonicare. You do not have to fully charge

your handle before rst use, as the handle is pre-

charged for rst use. However, it is recommended

to fully charge it after rst use.

Note: This charger is designed to properly charge

only one handle at a time. This charger is not

compatible with other models of Philips Sonicare.

Note: Do not place metallic objects in the travel

case, as handle charging may be aected and may

cause the charger to overheat.

Cleaning

Note: Do not clean the brush head, handle or

travel case in the dishwasher.

Toothbrush handle

1 Remove the brush head and rinse the metal

shaft area with warm water. Make sure you

remove any residual toothpaste.

Caution: Do not push on the rubber seal on

the metal shaft with sharp objects, as this may

cause damage.

2 Wipe the entire surface of the handle with a

damp cloth.

Note: Do not use isopropyl rubbing alcohol,

vinegar or bleach to clean handle as this may

cause discoloration.

22

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 22 13/02/17 16:38

Brush head

1 Rinse the brush head and bristles after each

use.

2 Remove the brush head from the handle and

rinse the brush head connection with warm

water at least once a week.

Charger and travel case

1 Unplug the charger and travel case before you

clean it.

2 Use a damp cloth to wipe the surface of the

charger and travel case.

Glass

1 Clean the glass with water and some mild soap.

2 Dry the glass with a soft towel.

The glass is dishwasher-safe.

Storage

If you are not going to use your Philips Sonicare

for an extended period of time, unplug the charger

from the wall socket, clean it and store it in a cool

and dry place away from direct sunlight.

Locating the model number

Look on the bottom of the Philips Sonicare

toothbrush handle for the model number

(HX992W, HX992B, HX992P, HX992S,

HX992L,HX993W, HX993B, HX993P, HX993S,

HX993L)

23

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 23 13/02/17 16:38

Disposal

This appliance contains a rechargeable battery

which must be disposed of properly. Contact your

local town or city ocials for battery disposal

information. You can also call 1-800-8-BATTERY

or visit www.rbrc.com for battery drop-o

locations.

For assistance, visit our website www.philips.com/

support or call 1-800-243-3050 toll free.

Removing the rechargeable battery

Warning: Only remove the rechargeable battery

when you discard the appliance. Make sure the

battery is completely empty when you remove it.

To remove the rechargeable battery, you need

a towel or cloth, a hammer and a at-head

(standard) screwdriver. Observe basic safety

precautions when you follow the procedure

outlined below. Be sure to protect your eyes,

hands, ngers, and the surface on which you work.

1 To deplete the rechargeable battery of any

charge, remove the handle from the charger,

turn on the Philips Sonicare and let it run until it

stops. Repeat this step until you can no longer

turn on the Philips Sonicare.

2 Remove and discard the brush head. Cover the

entire handle with a towel or cloth.

24

English

4235_021_2499_1_Booklet_Lux_A6_US_v1.indd 24 13/02/17 16:38

Page is loading ...

Sonicare HX9903/03 User manual

Sonicare HX9903/03 User manual

in other languages

Related papers

Other documents