Black & Decker WBV1400 T1 Owner's manual

Page is loading ...

4

ENGLISH

Intended use

Your Black & Decker vacuum cleaner has been designed for

wet or dry vacuum cleaning purposes. This product is

intended for household use only.

Safety instructions

Warning! When using mains-powered appliances, basic

safety precautions, including the following, should always be

followed to reduce the risk of fire, electric shock, personal

injury and material damage.

X Read all of this manual carefully before using the

appliance.

X The intended use is described in this manual. The use

of any accessory or attachment or the performance of

any operation with this appliance other than those

recommended in this instruction manual may present a

risk of personal injury.

X Retain this manual for future reference.

Using your appliance

X Make sure that the appliance is switched off before

connecting to or disconnecting from the power supply.

X Always take care when using the appliance.

X Do not use the appliance outdoors.

X Never pull the power supply cord to disconnect the plug

from the socket. Keep the power supply cord away from

heat, oil and sharp edges.

X If the power supply cord is damaged during use,

disconnect the appliance from the power supply

immediately. Do not touch the power supply cord before

disconnecting from the power supply.

X Disconnect the appliance from the power supply when

not in use, before fitting or removing parts and before

cleaning.

Safety of others

X This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience or knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety.

X Children should be supervised to ensure that they do

not play with the appliance.

After use

X Switch off and remove the plug from the socket before

leaving the appliance unattended and before changing,

cleaning or inspecting any parts of the appliance.

X When not in use, the appliance should be stored in a dry

place. Children should not have access to stored

appliances.

Inspection and repairs

X Before use, check the appliance for damaged or

defective parts. Check for breakage of parts, damage to

switches and any other conditions that may affect its

operation.

X Do not use the appliance if any part is damaged or

defective.

X Have any damaged or defective parts repaired or

replaced by an authorised repair agent.

X Before use, check the power supply cord for signs of

damage, ageing and wear.

X Do not use the appliance if the power supply cord or

mains plug is damaged or defective.

X If the power supply cord or mains plug is damaged or

defective it must be repaired by an authorised repair

agent in order to avoid a hazard. Do not cut the power

supply cord and do not attempt to repair it yourself.

X Never attempt to remove or replace any parts other than

those specified in this manual.

Electrical safety

Additional safety instructions for vacuum cleaners

X Before use, always make sure that the filter is correctly

seated.

X Do not use the appliance to pick up any materials that

could catch fire.

X Do not immerse the appliance in water.

X Keep the motor draught away from eyes and faces.

X Keep children and animals at a safe distance when

using this appliance.

X Always work from bottom up when using the appliance

on stairs, and keep the appliance at least a stair below

your working position.

X Do not use the appliance without the suction head or

another suitable accessory mounted to the tube.

X Keep your hair, clothing and gloves away from moving

parts. Do not reach into the rotating brush. Keep the

rotating brush away from the power supply cord.

X Do not use damaged accessories.

X Use only Black & Decker accessories.

X In blow mode, do not direct air towards bystanders.

X Do not use the appliance on animals.

This appliance is double insulated; therefore no

earth wire is required. Always check that the

power supply corresponds to the voltage on the

rating plate.

5

ENGLISH

Features

This appliance includes some or all of the following features.

1. Container

2. Extension tubes

3. Handle adapter

4. Hose

5. On/off switch

6. Handle

7. Blower connector

8. Upholstery tool

9. Crevice tool

10. Wheels

11. Brush/squeegee attachment

12. Floor head

Assembly

Removing the lid (fig. A)

X Release the two clips (14) that hold the lid (13) in place.

X Carefully remove the lid from the appliance.

Fitting the lid (fig. A)

X Fit the lid to the container (1) making sure that the

blower connector (7) is adjacent to the hose inlet (19)

and that the recesses in the lid line up with the clips (14).

X Fasten the two clips (14).

Assembling the wheel support (fig. B)

X Assemble the two parts of the wheel support (15)

together, make sure that they are firmly attached.

X Remove the lid as described above and turn the

container (1) upside down.

X Attach the wheel support (15) to the rim of the base of

the container (1) by applying slight pressure.

X Insert the four wheels (10), make sure that they click

firmly into place.

X Fit the lid as described above.

Fitting the paper dust bag (dry vacuuming only) (fig. C)

X Remove the lid as described above.

X Fit the cardboard flange (17) of the paper dust bag (16)

around the hose inlet (18).

X Fit the lid as described above.

Connecting and disconnecting the hose (fig. D)

To connect the hose:

X Insert the hose connector (20) into the inlet (19) of the

appliance.

X Line up the hose connector tabs with the slots in the

inlet.

X Turn the hose connector (20) clockwise until it locks into

position.

To disconnect the hose:

X Turn the hose connector (20) counter-clockwise and

pull out the hose.

Fitting the handle adaptor (fig. E)

X Push the handle adaptor (3) into the end of the hose (4)

until the flange is flush with the end of the hose.

Mounting the extension tube (fig. E)

X Firmly push one of the extension tubes (2) into the

handle adaptor (3).

X If required, attach the other extension tube (2) to the

end.

Mounting accessories (fig. E and F)

The crevice tool (9) allows for vacuuming in narrow and

hard-to-reach places. The upholstery tool (8) allows for

vacuuming on furniture, blinds, curtains, windows and stairs.

The brush or the squeegee blade are connected to the

brush/squeegee attachment (11) by sliding them into

position in between the guide ribs on the brush/squeegee

attachment (11).

The brush is used for dry vacuuming, the squeegee is used

for wet vacuuming.

The brush/squeegee attachment (11) can be attached to the

floor head (12) when required.

X To fit the brush/squeegee attachment (11), push it into

the floor head (12) until the two tabs (21) click into the

slots in the brush head.

X To remove the brush/squeegee attachment (11), press

the two tabs (21) inwards in the slots in the brush head

and carefully push it downwards until it is removed.

The accessories can be mounted on both the handle

adaptor (3) and the extension tubes (2).

X Firmly push the accessory onto the handle adaptor (3)

or extension tube (2) as required.

X To remove an accessory, pull the accessory from the

handle adaptor or the extension tube.

Use

Switching on and off (fig. G)

X To switch the appliance on, press the on/off switch (5)

to the I position.

X To switch the appliance off, press the on/off switch (5)

to the 0 position.

Vacuuming

X When operating the appliance, make sure that the hose

is not trapped, twisted or blocked.

X In case of overheating, a cut-out will operate and the

appliance will automatically stop.

6

ENGLISH

X If the appliance stops operating, unplug the appliance

and allow it to cool for 2-3 hours.

Wet pick-up

X Before using the appliance to clean up spills etc.,

remove the paper filter.

X Fit the squeegee blade to the brush/squeegee

attachment (11) and add the attachment to the floor

head (12).

Using the appliance as a blower (fig. H)

X If fitted, disconnect the hose from the container as

described above.

X Push the hose connector (20) over the end of the blower

connector (7) and make sure that it is a good fit.

X To disconnect the hose pull the hose connector (20)

from the blower connector (7).

Storing the appliance

Warning! When storing the appliance, switch the appliance

off and unplug it.

X Place the appliance in an upright position.

X Store the appliance in a dry location. The appliance can

be carried by the handle (6).

Maintenance

Your Black & Decker appliance has been designed to

operate over a long period of time with a minimum of

maintenance. Continuous satisfactory operation depends

upon proper tool care and regular cleaning.

Warning! Before performing any maintenance or cleaning

on the appliance, unplug the appliance.

X From time to time wipe the appliance with a damp cloth.

Do not use any abrasive or solvent-based cleaner. Do

not immerse the appliance in water.

Replacing the paper dust bag (fig. C)

The paper dust bag (16) must be replaced regularly.

X Remove the lid as previously described.

X Carefully pull the cardboard flange (17) of the paper

dust bag (16) from the hose inlet (18).

X Dispose of the paper dust bag (16) in normal household

waste.

X Wipe the inside of the container with a damp cloth. Do

not use any abrasive or solvent-based cleaner.

X Fit a replacement dust bag as previously described.

Cleaning the foam filter (fig. I and J)

The foam filter (22) prevents particles and larger objects

from entering the motor housing. The foam filter is fitted over

a plastic frame (23) which contains a safety float valve (24).

Note: The float safety valve rises with the water level,

blocking off the motor when the float safety valve reaches

the top.

The foam filter (22) is re-usable and should be cleaned

regularly.

X Remove the lid as previously described.

X Carefully slide the foam filter (22) from the plastic

frame (23).

X Brush any loose dust off the filter or wash with water and

a neutral detergent.

It is recommended that this filter is replaced regularly,

depending upon the frequency of use.

X Replace the foam filter (22) on the plastic frame (23).

X Replace the lid.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be fitted:

X Safely dispose of the old plug.

X Connect the brown lead to the live terminal in the new

plug.

X Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the fitting instructions supplied with good quality

plugs. Recommended fuse: 13A.

Protecting the environment

Should you find one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product

available for separate collection.

Separate collection of used products and packaging

allows materials to be recycled and used again. Re-

use of recycled materials helps prevent

environmental pollution and reduces the demand

for raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have

reached the end of their working life. To take advantage of

this service please return your product to any authorised

repair agent who will collect them on our behalf.

Separate collection. This product must not be

disposed of with normal household waste.

7

ENGLISH

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker office at the

address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of

our after-sales service and contacts are available on the

Internet at: www.2helpU.com.

Technical data

EC declaration of conformity

WBV1400 H1

Black & Decker declares that these products conform to:

2006/95/EC, EN 60335

Level of sound pressure, measured

according to EN 60704-1: = 78 dB(A)

The undersigned is responsible for compilation of the

technical file and makes this declaration on behalf of

Black & Decker

Kevin Hewitt

Director of Consumer Engineering

Spennymoor, County Durham, DL16 6JG,

United Kingdom

08-04-2009

Guarantee

Black & Decker is confident of the quality of its products and

offers an outstanding guarantee. This guarantee statement

is in addition to and in no way prejudices your statutory

rights. The guarantee is valid within the territories of the

Member States of the European Union and the European

Free Trade Area.

If a Black & Decker product becomes defective due to faulty

materials, workmanship or lack of conformity, within 24

months from the date of purchase, Black & Decker

guarantees to replace defective parts, repair products

subjected to fair wear and tear or replace such products to

make sure of the minimum inconvenience to the customer

unless:

X The product has been used for trade, professional or

hire purposes.

X The product has been subjected to misuse or neglect.

X The product has sustained damage through foreign

objects, substances or accidents.

X Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service

staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent by

contacting your local Black & Decker office at the address

indicated in this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our after-

sales service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to

register your new Black & Decker product and to be kept up

to date on new products and special offers. Further

information on the Black & Decker brand and our range of

products is available at www.blackanddecker.co.uk.

WBV1400

Voltage Vac 230

Power input W 400

Cable length m 5

Container size l 20

dust bag capacity l 12

Weight kg 3.5

Page is loading ...

Do not forget to register your product!

www.blackanddecker.co.uk/productregistration

Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and

product code to Black & Decker in your country.

Non dimenticate di registrare il prodotto!

www.blackanddecker.it/productregistration

Registrate il prodotto online su www.blackanddecker.it/productregistration o inviate nome, cognome e codice del

prodotto al centro Black & Decker del vostro paese.

ȃșȟ ȠıȥȑĲıĳı ȟį ȜįĳįȥȧȢȔĲıĳı ĳȡ ʍȢȡȨȪȟ Ĳįȣ!

www.blackanddecker.gr/productregistration

ȀĮĲĮȤȦȡȓıĲİ ĲȠ ʌȡȠȧȩȞ ıĮȢ ıİ ıȪȞįİıȘ ıĲȘ ıİȜȓįĮ www.blackanddecker.gr/productregistration Ȓ ıĲİȓȜĲİ ĲȠ

ȩȞȠȝĮ, İʌȓșİĲȠ ıĮȢ țĮȚ ĲȠȞ țȦįȚțȩ ʌȡȚȠȞȦĲȩȢ ıĲȘ Black & Decker ıĲȘ ȤȫȡĮ ıĮȢ.

TBA

04/09

Black & Decker WBV1400 T1 Owner's manual

This manual is also suitable for

Black & Decker WBV1400 T1 Owner's manual

in other languages

Related papers

Other documents