MD Sports BG125Y19003 Operating instructions

Assembly Instructions

MODEL

BG125Y19003

Target

www.medalsports.com

877-472-4296

English

This product is covered by a limited warranty that is effective for 90 days from the date of purchase. If, during the limited

warranty period, a part is found to be defective or breaks, we will offer replacement parts at no cost to you, the customer.

The only exceptions to the warranty include mainframes, table tops, playing surfaces, batteries or tools.

The above warranty will not apply in cases of damages due to improper usage, alteration, misuse, abuse, accidental

damage or neglect.

This Limited Warranty gives you speciﬁc legal rights and you may also have other rights vary from one State (province) to

another.

A PURCHASE RECEIPT (or other proof of purchase) will be required before any warranty service is initiated. For all

requests for warranty service, please feel free to contact our Consumer Service Department.

Please be aware of your product’s Limited Warranty for the return/refund policy from the store, We, at Medal Sports,

cannot handle the product which is out of product’s limited warranty since we only provide available parts. Thank you!

PLEASE CONTACT US BEFORE RETURNING THE PRODUCT TO THE STORE!

LIMITED 90 DAYS WARRANTY

MD SPORTS

877-472-4296

BG125Y19003 1(Continued on the next page.) www.medalsports.com

www.medalsports.com

Customer Service Toll Free

Please Contact

Mon.-Fri., 9:00 a.m. to 5:00 p.m. EST

For additional resources and Frequently Asked Questions, please visit us at

DO NOT RETURN TO STORE

WE ARE READY TO HELP

This product is intended for INDOOR use only.

Please do not sit, climb or lean on the product.

Please do not drag the product when moving it in order to avoid damaging the legs.

Please only use spray furniture polish to clean the exterior surfaces of the product.

This is not a children's toy, adult supervision is required for children playing this game.

1.

2.

3.

4.

5.

English

TOOLS REQUIRED

- Not Included

- Included

RECOMMENDED

IMPORTANT NOTICE!

Adult Assembly Required.

CHOKING HAZARD - This item contains small parts. Not suitable for children under 3 years.

WARNING

Phillips Screwdriver

Standard (Flat Head Screwdriver)

Allen Key

Electric Screwdrivers may be helpful during assembly; however, please set a low

torque and use extreme caution.

BG125Y19003 www.medalsports.com2(Continued on the next page.)

X2

At least 2 adults needed No children in assembly

area

Keep away from pets in

assembly area

Do not use or keep

product outdoors. For

indoor use only. No

wet/humid conditions.

Power Tools: Set to Low Torque

High Torque Over Tightened

Rim

11

x2

FOR FIG. 9

Rim Support Plate

12

x2

FOR FIG. 9

Backboard

15

x1

FOR FIG. 8

Rim Net

13

x2

FOR FIG. 10

Electronic Scorer

16

x1

FOR FIG. 8

Paddle Sensor

18

x2

FOR FIG. 10

Control Box

17

x1

FOR FIG. 15

Tube - 7

7

x2

FOR FIG. 1, 3

Tube - 8

8

x1

FOR FIG. 6

Tube - 9

9

x1

FOR FIG . 7

Tube - 10

10

x1

FOR FIG . 13

Tube - 4 - Right

4R

x1

FOR FIG. 4

Tube - 4 - Left

4L

x1

FOR FIG. 4

Tube - 5

5

x2

FOR FIG. 6

Tube - 6

6

x2

FOR FIG. 5

Self-Stick Strap

20

x2

FOR FIG. 15

Tube - 2

2

x2

FOR FIG. 2

Tube - 3 - Right

3R

x1

FOR FIG. 1

Tube - 3 - Left

3L

x1

FOR FIG. 1

Ball Return Net

14

x1

FOR FIG. 12

Wire clip

19

x6

FOR FIG. 17

BG125Y19003 www.medalsports.com3(Continued on the next page.)

English

PARTS IDENTIFIER

Tube - 1

1

x2

FOR FIG. 2

PART NUMBER FIG NUMBER

QUANTITY

PART

PART NAME

Push Button

P1

x8

FIG. 1, 4, 5, 6

Plastic Pole Insert

P2

x4

FOR FIG. 1, 2

Pole Holder

P3

x4

FOR FIG. 1, 6

HARDWARE

PRE-INSTALLED PARTS

End Cap

P4

x2

FOR FIG. 5

Air Pump

22

x1

Basketball

21

x4

M6x42mm Bolt

A1

x4

FOR FIG. 5

M6x37mm Bolt

A2

x12

FOR FIG. 1, 3, 4, 13

Spacer

A3

x4

FOR FIG. 5

M6x18mm Bolt

A5

x16

FOR FIG. 9, 10

M6 Nut

A7

x36

FOR FIG. 1, 3, 4, 5, 9, 10,

11, 13, 14

M6 Plastic Washer

A8

x12

M6 Washer

A6

x60

FOR FIG. 1, 3, 4, 5, 9, 10,

11, 13, 14

M6x57mm Bolt

A4

x4

FIG. 11, 14

Allen Key

x1

FOR FIG. 8

Wrench

A10

x1

M4x15mm Bolt

A9

x3

FIG. 10, 11, 14

A11

BG125Y19003 www.medalsports.com4(Continued on the next page.)

English

ACCESSORIES

Needle

22

x2

x2 x6

x2

1

6

13

18 19 20

x2

14 15 16 17

2

7 8 9 10 11 12

5

3R 3L 4L4R

Find a clean, level place to begin the assembly of your product.

Verify that you have all listed parts as shown on the part list pages. If any parts are missing, call our customer service.

1.

2.

BEFORE ASSEMBLY

BG125Y19003 www.medalsports.com5(Continued on the next page.)

BEFORE ASSEMBLY

Please inspect and layout all the POLES and parts

English

FIG. 1

FIG. 2

x2

1

x2

P2

Pre-installed

x2

2

x1

3R

x2

P3

Pre-installed

x1

x4

x8

x4

x1

7

A2

A6

A7

A10

A11

x2

P2

Pre-installed

x1

3L

3R

3L

7

P2

P3

3R

A2

A6

7

A6

A7

1

2

A2

A6

3L

7

3R

A6

A7

P1

BG125Y19003 www.medalsports.com6(Continued on the next page.)

ASSEMBLY

English

Safety lock

x2

P1

Pre-installed

FIG. 3

x4

A7

x1

x8

7

A10

x1

A11

A6

x4

A2

FIG. 4

4R

A2

A6

A7

4L

A10

A11

x4

x1

x2

x1

1

2

7

4R

4L

A2

A6

A7

A2

A6

A7

Pre-installed

P1

x2

P1

ASSEMBLY

BG125Y19003 www.medalsports.com7(Continued on the next page.)

English

FIG. 5

Pre-installed

x2

6

A1

A6

A3

A6

6

A1

A6

A3

A7

4L

6

A7

2

6

P1

P4

x8

x1

x4

x1

A6

A10

A1

x4

A3

A7

A11

Note: Pull out tube - 6 (6) till push

button (P1) pop out and ﬁxed.

BG125Y19003 www.medalsports.com8(Continued on the next page.)

ASSEMBLY

English

Pre-installed

5

8

P3

P1

x2

x1

x2

Pre-installed

P1

x2

9

FIG. 7

9

x1

FIG. 6

5

8

BG125Y19003 www.medalsports.com9(Continued on the next page.)

ASSEMBLY

English

x1

x3

x1

15

A9

16

FIG. 9

x2

x8

x16

x2

11

A5

A6

12

x8

x1

A7

A11

A10

FIG. 8

15

16

A9

11

A6

A5

15

A7

A6

12

Note: Ensure that washers are used

on both sides of the backboard as

shown in FIG. 9.

Note: DO NOT over tighten bolts.

BG125Y19003 www.medalsports.com10(Continued on the next page.)

ASSEMBLY

English

13

11

Note: Attach the part with larger

meshes to the rim.

x2

x8

x2

FIG. 10

13

A7

A5

18

x8

x1

x8

x1

A8

A11

A6

A10

13

11

11 13

A5

18

A6

A7

A8

Note: Connect paddle sensor (18)

to the backboard.

BG125Y19003 www.medalsports.com11(Continued on the next page.)

ASSEMBLY

English

x2

x1

15

FIG. 11

1

A4

A8

A4

A6

A7

A8

A10

A11

Note: Please do not use any bolts on

the backboard at this step. The

bolts will be added later for the

ramp tab.

BG125Y19003 www.medalsports.com12(Continued on the next page.)

ASSEMBLY

English

Note: With the help of another adult,

attach the backboard (15) to the top

tubes - 1 (1).

x1

14

Connect Velcro

Strap here.

FIG. 12

14

9

14

1

Note: Slide in the elastic straps onto

tube - 1, then slide the sleeves of ball

return net (14) onto tubes at the top.

Note: To secure the ball return net (14)

to tube - 1 (1), attach the elastic straps

over the nuts as shown in FIG. 12.

BG125Y19003 www.medalsports.com13(Continued on the next page.)

ASSEMBLY

English

x1

x2

x4

x2

x1

10

A2

A6

A7

A10

A11

FIG. 13

10

9

A7

9

14

A6

9

A2

Note: After the elastic straps are bound to tube 9 (9),

slide tube - 10 (10) into the sleeve of the ball return net,

then attach it to tube - 9 (9) as shown in FIG. 13. Fasten

the bolt (A2) with the allen key to ﬁnish this step.

BG125Y19003 www.medalsports.com14(Continued on the next page.)

ASSEMBLY

English

Ramp Tab

x2

x1

A4

A6

A7

A8

A10

A11

FIG. 14

Connect Velcro Strap here.

15

A4

A8

A6

A7

1

14

15

14

Note: At each bottom hole of the backboard,

attach the ramp tabs on ball return net (14)

using bolts (A4), washers (A6 & A8), and nuts

(A7) as shown in FIG. 14.

BG125Y19003 www.medalsports.com15(Continued on the next page.)

ASSEMBLY

English

VISITORCONTROL

HOME

Control Wire

Sensor wire

Control Wire

x1

x2

17

20

FIG. 16

14

FIG. 15

17

14

9

17

Electronic Scorer

VISITOR

CONTROL

HOME

16

18

Note: Insert the control wire and the sensor

wires into the electronic scorer (16).

BG125Y19003 www.medalsports.com16(Continued on the next page.)

ASSEMBLY

English

Note: Run the rest of the control wire

through the loops on the ball return

net (14). Place the control wire on the

tube - 9 (9) using the self-stick straps

(20) as shown in FIG. 15.

x6

19

Wire clip

15

19

Paddle

Sensor

Control

Box

Paddle

Sensor

FIG. 17

Note: Fix the wires on both sides

onto the corresponding clips.

BG125Y19003 www.medalsports.com17(Continued on the next page.)

ASSEMBLY

English

WARNING

Do NOT trap your

ﬁngers when folding the game.

STEP 1 STEP 2

STEP 4STEP 3

8

Note: Push tube - 8 (8)

downwards.

Note: Push tube - 9 (9) upwards to fold.

Note: Release the tubes by pressing

the push button (P1) as shown.

WARNING

Two Adults Required

9

P1

Note: Buckle the safety lock

by bending it upward.

BG125Y19003 www.medalsports.com18(Continued on the next page.)

HOW TO FOLD THE GAME FOR STORAGE

English

Note: Push tube - 9 (9) downwards.

Note: Pull out tube - 6 (6) till push

button (P1) pop out and ﬁxed.

6

8

9

STEP 3 STEP 4

STEP 1 STEP 2

Note: Release the safety lock

by bending it downward.

P1

WARNING

Two Adults Required

BG125Y19003 www.medalsports.com19(Continued on the next page.)

HOW TO UNFOLD GAME TO REPLAY

English

Note: Push tube - 8 (8) upwards.

Page is loading ...

MD Sports BG125Y19003 Operating instructions

This manual is also suitable for

MD Sports BG125Y19003 Operating instructions

Related papers

Other documents