2. Danfoss
  3. DHP-A

Danfoss DHP-A Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Danfoss DHP-A Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Electrical
installation instructions
Danfoss Heat Pumps
DHP-A
VWBMG202
DHP-A
Electrical installation – Page 2
VWBMG202
Contents
DHP-A 6, 400V 3N ......... 3–6
DHP-A 8, 400V 3N .........7-10
DHP-A 10, 400V 3N ...... 11 –14
DHP-A 12, 400V 3N ...... 15–18
DHP-A 6 SP, 230V 1N..... 19–22
DHP-A 8 SP, 230V 1N......23-26
DHP-A 10 SP, 230V 1N ... 27–30
DHP-A 12 SP, 230V 1N ... 31–34
Electrical installation
Danfoss heat pumps are factory-wired internally. The leads that are to
be connected are the mains supply (5-wire DPH), outdoor
temperature sensor and room sensors (if any).
• All electrical wiring must be carried out by a certified electrician in
compliance with local and national codes and regulations. When in
doubt, contact the local electricity distributor.
•Themainsleadispassedthroughthetopoftheunit.
•Removethefrontpaneltogetaccesstotheterminalblocks.Connect
themainsleadtotheterminalblockaccordingtotheaccompanying
schematic diagram.
•Theconnectionoftheheatpumptothemainssupplymustbehard-
wired and a multi-pole switch (safety switch) must be installed in the
power supply line to the unit.
WARNING! To disconnect the power supply to the heat pump, the
safety switch must be switched off.
NOTE!Thecablestotheoutdoorandindoorsensorscarrylowvoltage.
Interference from surrounding cables may affect these and cause incor-
rect information to be sent to the control unit. It is therefore vitally
important thatcarefulconsiderationbe givento positioningof cables.
Low-voltage cables must be kept well separated from high-voltage
cables.Itis importantthat low-voltagecables arerun parallelto high-
voltagecables andseparatedby adistance of atleast 25cm forcable
lengths up to 100 m. For longer cable lengths, the distance between
cables should be increased.
Important information
Before switching on the power supply to the heat pump, you must
ensure that the heating system, chilled water line and hot water heater
arefilledandvented.Otherwise,thecirculationpumpscanbeseverely
damaged.
DHP-A
Electrical installation – Page 3
VWBMG202
DHP-A
Electrical installation – Page 4
VWBMG202
DHP-A
Electrical installation – Page 5
VWBMG202
DHP-A
Electrical installation – Page 6
VWBMG202
DHP-A
Electrical installation – Page 7
VWBMG202
DHP-A
Electrical installation – Page 8
VWBMG202
DHP-A
Electrical installation – Page 9
VWBMG202
DHP-A
Electrical installation – Page 10
VWBMG202
DHP-A
Electrical installation – Page 11
VWBMG202
DHP-A
Electrical installation – Page 12
VWBMG202
DHP-A
Electrical installation – Page 13
VWBMG202
DHP-A
Electrical installation – Page 14
VWBMG202
DHP-A
Electrical installation – Page 15
VWBMG202
DHP-A
Electrical installation – Page 16
VWBMG202
DHP-A
Electrical installation – Page 17
VWBMG202
DHP-A
Electrical installation – Page 18
VWBMG202
DHP-A SP
Electrical installation – Page 19
VWBMG202
DHP-A SP
Electrical installation – Page 20
VWBMG202
/