Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 1
© 2002, ADTRAN, Inc. Total Access 600 Series User Manual
TOTAL ACCESS 600 SERIES SHDSL IAD
User Interface Guide
April 2002
4200683L1 SHDSL Total Access 608
4200643L1 SHDSL Total Access 604
4200612L3 SHDSL Total Access 612
4200616L3 SHDSL Total Access 616
4200624L3 SHDSL Total Access 624
Total Access 600 Series User Manual © 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 2
Trademarks
Any brand names and product names included in this manual are trademarks,
registered trademarks, or trade names of their respective holders.
Total Access is a registered trademark of ADTRAN, Inc.
To the Holder of the Manual
The contents of this manual are current as of the date of publication. ADTRAN
reserves the right to change the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential
damages or for commercial losses even if ADTRAN has been advised thereof as a
result of issue of this publication.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
(256) 963-8000
©2002 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 3
© 2002, ADTRAN, Inc. Total Access 600 Series User Manual
Safety Instructions
When using your telephone equipment, please follow these basic safety
precautions to reduce the risk of fire, electrical shock, or personal injury:
1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless-type) during an electrical storm.
There is a remote risk of shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the man-
ual. Do not dispose of batteries in a fire. They may explode. Check with local
codes for special disposal instructions.
Save These Important Safety Instructions
Notes provide additional useful information.
Caution signify information that could prevent service interruption.
Warnings provide information that could prevent damage to the equipment or
endangerment to human life.
Total Access 600 Series User Manual © 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 4
Federal Communications Commission Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 5
© 2002, ADTRAN, Inc. Total Access 600 Series User Manual
FCC regulations require that the following information be provided in this manual
to the customer:
1. This equipment complies with Part 68 of the FCC rules. On the side of the bot-
tom of this equipment is a label that contains, among other information, the
FCC Registration Number and Ringer Equivalence Number (REN), if applica-
ble, for this equipment. If required, this information must be given to the tele-
phone company.
2. An FCC-compliant telephone cord and modular plug is provided with this
equipment. This equipment is designed to be connected to the telephone net-
work or premises wiring using a compatible modular jack which is Part 68-
compliant. See installation instructions for details.
3. If your telephone equipment (TA 600) causes harm to the telephone network,
the telephone company may discontinue your service temporarily. If possible,
they will notify you in advance. But if advance notice isn’t practical, you will
be notified as soon as possible. You will be advised of your right to file a com-
plaint with the FCC.
4. Your telephone company may make changes in its facilities, equipment, opera-
tions, or procedures that could affect the proper operation of your equipment. If
they do, you will be given advance notice to give you an opportunity to main-
tain uninterrupted service.
5. If you experience trouble with this equipment (TA 600), please contact ADT-
RAN for repair/warranty information. The telephone company may ask you to
disconnect this equipment from the network until the problem has been cor-
rected or until you are sure the equipment is not malfunctioning.
6. This unit contains no user-serviceable parts.
7. The FCC recommends that the AC outlet to which equipment requiring AC
power is to be installed is provided with an AC surge arrester.
8. The REN is used to determine the quantity of devices which may be connected
to the telephone line. Excessive RENs on the telephone line may result in the
devices not ringing in response to an incoming call. In most, but not all areas,
the sum of RENs should not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the total RENs, con-
tact the local telephone company.
9. The following information may be required when applying to your local tele-
phone company for leased line facilities.
6HUYLFH7\SH 5(162& ),& 862&
$QDORJ6HUYLFH/LIH/LQH %) /6*6 5-&
Total Access 600 Series User Manual © 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 6
Industry Canada Compliance Information
Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the
“IC:” in front of the certification/registration number) signifies that the Industry Canada technical
specifications were met.
Notice: The Ringer Equivalence Number (REN) for this terminal equipment is supplied in the
documentation or on the product labeling/markings. The REN assigned to each terminal device indicates
the maximum number of terminals that can be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the
RENs of all the devices should not exceed five (5).
Canadian Emissions Requirements
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the
Department of Communications.
Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques
de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee
par le ministre des Communications.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 7
© 2002, ADTRAN, Inc. Total Access 600 Series User Manual
Warranty and Customer Service
ADTRAN will repair and return this product within ten years from the date of shipment if it does not meet
its published specifications or fails while in service. For detailed warranty, repair, and return information
refer to the ADTRAN Equipment Warranty and Repair and Return Policy Procedure.
Return Material Authorization (RMA) is required prior to returning equipment to ADTRAN.
For service, RMA requests, or further information, contact one of the numbers listed at the end of this
section.
LIMITED PRODUCT WARRANTY
ADTRAN warrants that for ten years from the date of shipment to Customer, all products manufactured by
ADTRAN will be free from defects in materials and workmanship. ADTRAN also warrants that products
will conform to the applicable specifications and drawings for such products, as contained in the Product
Manual or in ADTRAN's internal specifications and drawings for such products (which may or may not be
reflected in the Product Manual). This warranty only applies if Customer gives ADTRAN written notice of
defects during the warranty period. Upon such notice, ADTRAN will, at its option, either repair or replace
the defective item. If ADTRAN is unable, in a reasonable time, to repair or replace any equipment to a
condition as warranted, Customer is entitled to a full refund of the purchase price upon return of the
equipment to ADTRAN. This warranty applies only to the original purchaser and is not transferable
without ADTRAN's express written permission. This warranty becomes null and void if Customer
modifies or alters the equipment in any way, other than as specifically authorized by ADTRAN.
EXCEPT FOR THE LIMITED WARRANTY DESCRIBED ABOVE, THE FOREGOING
CONSTITUTES THE SOLE AND EXCLUSIVE REMEDY OF THE CUSTOMER AND THE
EXCLUSIVE LIABILITY OF ADTRAN AND IS IN LIEU OF ANY AND ALL OTHER WARRANTIES
(EXPRESSED OR IMPLIED). ADTRAN SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES,
INCLUDING (WITHOUT LIMITATION), ALL WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. SOME STATES DO NOT ALLOW THE EXCLUSION
OF IMPLIED WARRANTIES, SO THIS EXCLUSION MAY NOT APPLY TO CUSTOMER.
In no event will ADTRAN or its suppliers be liable to Customer for any incidental, special, punitive,
exemplary or consequential damages experienced by either Customer or a third party (including, but not
limited to, loss of data or information, loss of profits, or loss of use). ADTRAN is not liable for damages
for any cause whatsoever (whether based in contract, tort, or otherwise) in excess of the amount paid for
the item. Some states do not allow the limitation or exclusion of liability for incidental or consequential
damages, so the above limitation or exclusion may not apply to Customer.
Total Access 600 Series User Manual © 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 8
Customer Service, Product Support Information, and Training
ADTRAN will repair and return this product if within ten years from the date of shipment the product does
not meet its published specification or the product fails while in service.
A return material authorization (RMA) is required prior to returning equipment to ADTRAN. For service,
RMA requests, training, or more information, use the contact information given below.
Repair and Return
If you determine that a repair is needed, please contact our Customer and Product Service (CAPS)
department to have an RMA number issued. CAPS should also be contacted to obtain information
regarding equipment currently in house or possible fees associated with repair.
Identify the RMA number clearly on the package (below address), and return to the following address:
ADTRAN Customer and Product Service
901 Explorer Blvd. (East Tower)
Huntsville, Alabama 35806
RMA # _____________
Pre-Sales Inquiries and Applications Support
Your reseller should serve as the first point of contact for support. If additional pre-sales support is needed,
the ADTRAN Support web site provides a variety of support services such as a searchable knowledge
base, latest product documentation, application briefs, case studies, and a link to submit a question to an
Applications Engineer. All of this, and more, is available at:
http://support.adtran.com
When needed, further pre-sales assistance is available by calling our Applications Engineering
Department.
CAPS Department (256) 963-8722
Applications Engineering (800) 615-1176
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 9
© 2002, ADTRAN, Inc. Total Access 600 Series User Manual
Post-Sale Support
Your reseller should serve as the first point of contact for support. If additional support is needed, the
ADTRAN Support web site provides a variety of support services such as a searchable knowledge base,
updated firmware releases, latest product documentation, service request ticket generation and trouble-
shooting tools. All of this, and more, is available at:
http://support.adtran.com
When needed, further post-sales assistance is available by calling our Technical Support Center. Please
have your unit serial number available when you call.
Installation and Maintenance Support
The ADTRAN Custom Extended Services (ACES) program offers multiple types and levels of installation
and maintenance services which allow you to choose the kind of assistance you need. This support is
available at:
http://www.adtran.com/aces
For questions, call the ACES Help Desk.
Training
The Enterprise Network (EN) Technical Training Department offers training on our most popular products.
These courses include overviews on product features and functions while covering applications of
ADTRAN's product lines. ADTRAN provides a variety of training options, including customized training
and courses taught at our facilities or at your site. For more information about training, please contact your
Territory Manager or the Enterprise Training Coordinator.
Technical Support (888) 4ADTRAN
ACES Help Desk (888) 874-ACES (2237)
Training Phone (800) 615-1176, ext. 7500
Training Fax (256) 963-6700
Training Email traini[email protected]om
Total Access 600 Series User Manual © 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 10
TOTAL ACCESS 600 SERIES SHDSL IAD USER INTERFACE GUIDE
This document is designed for use by network administrators and others who will configure and provision the Total
Access 600 Series SHDSL Integrated Access Device (IAD). It contains overview information, information about
navigating the VT 100 user interface, configuration information, and menu descriptions.
CONTENTS
7RWDO$FFHVV2YHUYLHZ
$QDORJ/LIHOLQH
)LUPZDUH8SGDWHV
9RLFH2YHU'6/2YHUYLHZ
9RLFH2YHU$702YHUYLHZ
9RLFH2YHU'6/$SSOLFDWLRQ
&RQILJXULQJWKH7RWDO$FFHVV
6\VWHP,QIR
6\VWHP1DPH
6\VWHP/RFDWLRQ
6\VWHP&RQWDFW
8QLW1DPH
&/(,&RGH
3DUW1XPEHU
6HULDO1XPEHU
)LUPZDUH5HYLVLRQ
%RRWFRGH5HYLVLRQ
6\VWHP8SWLPH
'DWH7LPH
6\VWHP&RQILJ
1HWZRUN7LPLQJ0RGH
1HWZRUN
7HOQHW$FFHVV
7HOQHW8VHU/LVW
1DPH
$XWKHQ0HWKRG
3DVVZRUG
,GOH7LPH
/HYHO
0DLQW3RUW0HQX
3DVVZRUG3URWHFW
3DVVZRUG
%DXG5DWH
'DWD%LWV
3DULW\
6WRS%LWV
1HWZRUN7LPH
6HUYHU7\SH
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 11
© 2002, ADTRAN, Inc. Total Access 600 Series User Manual
177LPH
6173
$FWLYH
7LPH=RQH
$GMXVWIRU'D\OLJKW6DYLQJ
+RVW$GGUHVV
5HIUHVK
6WDWXV
6\VWHP8WLOLW\
8SJUDGH)LUPZDUH
7UDQVIHU0HWKRG
7)736HUYHU$GGUHVV
7)736HUYHU)LOHQDPH
7UDQVIHU6WDWXV
6WDUW7UDQVIHU
$ERUW7UDQVIHU
&RQILJ7UDQVIHU
7UDQVIHU0HWKRG
7UDQVIHU7\SH
7)736HUYHU,3$GGUHVV
7)736HUYHU)LOHQDPH
&XUUHQW7UDQVIHU6WDWXV
3UHYLRXV7UDQVIHU6WDWXV
/RDGDQG8VH&RQILJ
6DYH&RQILJ5HPRWHO\
3LQJ
6WDUW6WRS
+RVW$GGUHVV
6L]H
RI3DFNHWV
7UDQVPLWV
5HFHLYHV
/RVV
&RQILJXULQJ:$16HWWLQJV
'6/$07\SH
/D\HU2QH,QWHUIDFH
/D\HU7ZR3URWRFRO
$70&RQILJ
,GOH&HOOV
'DWD6FUDPEOLQJ
$706WDWV
$37[&HOOV
$35[&HOOV
$35[2$0&HOOV
$35HFHLYH&HOOV'LVFDUGHG
$35HFHLYH&HOO(UURUV
$36\QF
$32XW2I&HOO'HOLQHDWLRQ
$$/7UDQVPLW)UDPHV
Total Access 600 Series User Manual © 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 12
$$/5HFHLYH)UDPHV
$$/7UDQVPLW'LVFDUGHG)UDPHV
$$/5HFHLYH(UURUV
$$/5HFHLYH'LVFDUGHG)UDPHV
$$/1R$70)UDPHV
$$/1R'DWD3DFNHWV
&OHDU6WDWV
&RQILJXULQJWKH5RXWHU±&RQILJXUDWLRQ
*OREDO
,3
0RGH
6WDWLF5RXWHV
'+&36HUYHU
'RPDLQ1DPHV
8'35HOD\
0RGH
8'35HOD\/LVW
%ULGJH
0RGH
$GGUHVV7DEOH
6HFXULW\
)LOWHU'HILQHV
)LOWHU'HILQHV0$&)LOWHU'HILQHV
)LOWHU'HILQHV3DWWHUQ)LOWHU'HILQHV
)LOWHU'HILQHV,3)LOWHU'HILQHV
(WKHUQHW
,3
,3$GGUHVV
6XEQHW0DVN
'HIDXOW*DWHZD\
5,3
3UR[\$53
0$&$GGUHVV
:$1
/3URWRFRO
$70
'HVFULSWLRQ
93,
9&,
3&53HDN&HOO5DWH
4264XDOLW\RI6HUYLFH
3URWRFRO
5)&,3
$FWLYH
)DU(QG,3$GGUHVV
,3QHWPDVN
/RFDO,3$GGUHVV
1$7
5,3
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 13
© 2002, ADTRAN, Inc. Total Access 600 Series User Manual
5)&%ULGJH
333R$70
$XWKHQWLFDWLRQ
7;0HWKRG
7;8VHUQDPH
7;3DVVZRUG
5;8VHUQDPH
5;3DVVZRUG
,3
0RGH
/RFDO,3
1HWPDVN
5HPRWH,3
1$7
5RXWH
5,3
333
9-&RPSUHVVLRQ
0D[&RQILJ
0D[7LPHU
0D[)DLOXUH
(QFDSVXODWLRQ
)LOWHUV
:$172/$1,Q
,Q([FHSWLRQV
/$172:$12XW
2XW([FHSWLRQV
&RQILJXULQJWKH5RXWHU±6WDWXV
6HVVLRQ
$53FDFKH
%ULGJH7DEOH
,35RXWHV
/$16WDWV
,36WDWV
&RQILJXULQJWKH5RXWHU±/RJV
6\VORJ+RVW
333/RJ
&RQQHFWLRQ/RJ
1HWZRUN/RJ
$FWLYH
:UDS
/HYHO
9LHZ
&OHDU
&RQILJXULQJ9RLFH6XSSRUW±&RQILJ
&DOO&RQWURO
93,
9&,
&RQILJXULQJ9RLFH6XSSRUW±6WDWXV
Total Access 600 Series User Manual © 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 14
*DWHZD\6WDWV
39&6WDWV
32766WDWV
&OHDU6WDWV
0DQDJLQJWKH0RGXOHV±0RGXOHV
1(76+'6/
0HQX
'DWD5DWH
)UDPH0RGH
$QQH[$%
,78*VSDQ
7HVW
1HWZRUN/RRSEDFN
6HQG&KHFN
6HQG&KHFN$/7
6WDWXV
6LJQDO6WDWH
'DWD5DWH
)UDPH0RGH
*KV6WDWH
*KV(YHQW
);6
(&$'3&0
0DQDJLQJWKH0RGXOHV±96HWXS
$70)5,:)
0RGH
)5)
)5)
&RQILJXUDWLRQ
$SSHQGL[$8SGDWLQJ7RWDO$FFHVV)LUPZDUHXVLQJ;02'(0
8SGDWLQJ)LUPZDUHYLDD)RUFHG'RZQORDG
8SGDWLQJ)LUPZDUHYLDWKH&RQVROH0HQXV
$SSHQGL[%8SGDWLQJ7RWDO$FFHVV)LUPZDUHXVLQJ7)73
$SSHQGL[&1DYLJDWLQJWKH7HUPLQDO0HQXV
7HUPLQDO0HQX:LQGRZ
0HQX3DWK
:LQGRZ3DQHV
:LQGRZ3DQH1DYLJDWLRQ
5LJKW:LQGRZ3DQH1RWDWLRQ
$GGLWLRQDO7HUPLQDO0HQX:LQGRZ)HDWXUHV
1DYLJDWLQJ8VLQJWKH.H\ERDUG.H\V
0RYLQJWKURXJKWKH0HQXV
6HVVLRQ0DQDJHPHQW.H\VWURNHV
&RQILJXUDWLRQ.H\VWURNHV
*HWWLQJ+HOS
$SSHQGL['9RLFH*DWHZD\4XLFN6WDUW3URFHGXUH9RLFH7XUQXS
9RLFH7XUQ8S
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 15
© 2002, ADTRAN, Inc. Total Access 600 Series User Manual
$SSHQGL[(5)&4XLFN6WDUW,35RXWLQJ
,35RXWLQJ
$SSHQGL[)5)&4XLFN6WDUW,35RXWLQJZLWK1$7
,35RXWLQJZLWK1$7
$SSHQGL[*5)&4XLFN6WDUW%ULGJLQJ
%ULGJLQJ
$SSHQGL[+&UDIW3RUW&RQQHFWLRQ3LQRXW
FIGURES
)LJXUH 7RWDO$FFHVV5HDU3DQHO
)LJXUH 9RLFHRYHU'6/
)LJXUH 6\VWHP,QIRUPDWLRQ0HQX
)LJXUH 6\VWHP&RQILJXUDWLRQ0HQX
)LJXUH 6\VWHP8WLOLW\0HQX
)LJXUH :$10HQX
)LJXUH $70&RQILJ0HQX
)LJXUH $706WDWV0HQX
)LJXUH 5RXWHU&RQILJXUDWLRQ0HQX
)LJXUH *OREDO0HQX
)LJXUH (WKHUQHW0HQX
)LJXUH :$10HQX
)LJXUH 5RXWHU6WDWXV0HQX
)LJXUH 5RXWHU/RJV0HQX
)LJXUH 9RLFH&RQILJ0HQX
)LJXUH 9RLFH6WDWXV0HQX
)LJXUH 0RGXOHV0HQX
)LJXUH 96HWXS0HQX
)LJXUH 7RSOHYHO7HUPLQDO0HQX:LQGRZ
)LJXUH $SSOLFDWLRQ'LDJUDP
)LJXUH $SSOLFDWLRQ'LDJUDP
Total Access 600 Series User Manual © 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 16
1. TOTAL ACCESS 600 OVERVIEW
The Total Access 600 is a complete solution Integrated Access Device (IAD) for Voice over ATM (VoATM) appli-
cations. The unit includes a modular network interface, Nx64 V.35 interface, 10/100BaseT interface, FXS ports, life-
line voice backup, and an optional battery back-up for added security. The Total Access 600 can provision, test, and
provide status for any of the voice and data interfaces. All connections are made via the rear panel. In addition to a
built-in IP router, the Total Access 600 contains an echo canceller and ADPCM compression modules necessary for
VoATM applications.
Analog Lifeline
The
LIFE LINE
connector on the rear panel (see Figure 1) provides assured voice for port 1. When a connection to the
Voice Gateway is not possible due to loss of power or some other reason, an on-board relay opens and the first port of
the voice connector is provided with analog voice from the analog lifeline connection.
Figure 1. Total Access 600 Rear Panel
Firmware Updates
Firmware can be updated by using XMODEM transfer protocol via the unit’s
CRAFT
port (see Figure 1) or by using
TFTP from a network server. (See Appendix A. Updating Total Access 600 Firmware using XMODEM on page 54
and Appendix B. Updating Total Access 600 Firmware using TFTP on page 57.)
The terminal menu is the access point to all other operations. Each terminal menu item has several functions and sub-
menus that identify and provide access to specific operations and parameters. These menu selections are described later
in this User Interface Guide.
For the analog lifeline feature to work, the user must subscribe to an analog voice line and it must
be connected via the lifeline connector.
See Appendix C for instructions about navigating the terminal menus.
See Appendix H for the CRAFT port connection pin-out.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 17
© 2002, ADTRAN, Inc. Total Access 600 Series User Manual
2. VOICE OVER DSL OVERVIEW
Voice over DSL (VoDSL) refers to providing toll quality voice access to the Public Switched Telephone Network
(PSTN) over twisted copper pair using DSL. Data can be combined with multiple voice lines over a single medium via
DSL, thus yielding many advantages over traditional TDM technologies.
Traditional TDM technologies are limited by statically allocating bandwidth. DSL overcomes this by providing a large
bandwidth and utilizing other technologies, such as ATM, to dynamically assign bandwidth as it is needed. Because
of this, the user is able to add voice and data connections over a DSL line with flexibility and ease.
3. VOICE OVER ATM OVERVIEW
Voice over ATM is the technology used to transmit voice conversations over a data network using Asynchronous
Transfer Mode (ATM). There are several potential benefits to moving voice over a data network using ATM. First, the
small, fixed-length cells require lower processing overhead. Second, these small, fixed-length cells allow higher trans-
mission speeds than traditional packet switching methods.
ATM allocates bandwidth on demand, making it suitable for high-speed connection of voice, data, and video services.
Conventional networks carry data in a synchronous manner. Because empty slots are circulating even when the link is
not needed, network capacity is wasted. ATM automatically adjusts the network capacity to meet the system needs.
4. VOICE OVER DSL APPLICATION
The Total Access 600 connects to a DSLAM via DSL and ATM. The Total Access 600 has a built in echo canceller
that provides G.165 echo cancellation. The module can automatically detect ADPCM and enable it as needed.
Figure 2 shows a typical VoDSL application. The Total Access 600 connects to the ATM network, via a DSLAM, to
provide both voice and high speed data from a single platform.
Total Access 600 Series User Manual © 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 18
Figure 2. Voice over DSL
DS3MX
P
O
W
E
R
S
T
A
T
U
S
T
E
S
T
L
O
C
K
O
U
T
O
N
L
I
N
E
A
P
S
T
E
S
T
/
E
N
A
B
L
E
1
1
8
1
0
2
0
L
1
DS3MX
P
O
W
E
R
S
T
A
T
U
S
T
E
S
T
L
O
C
K
O
U
T
O
N
L
I
N
E
A
P
S
T
E
S
T
/
E
N
A
B
L
E
1
1
8
1
0
2
0
L
1
SCU
F
S
E
M
O
D
E
S
E
L
E
C
T
A
L
M
H
S
T
A
C
O
C
R
A
F
T
A
C
O
1
1
8
1
0
1
5
L
1
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
QFC-C
D
S
X
P
W
R
D
S
X
D
S
X
T
S
T
A
L
M
A
C
T
A
P
S
G
R
N
=
N
O
R
M
Y
E
L
=
M
A
N
1
1
8
1
3
0
0
L
1
D
S
X
#
2
#
3
#
4
#
1
QFC-C
D
S
X
P
W
R
D
S
X
D
S
X
T
S
T
A
L
M
A
C
T
A
P
S
G
R
N
=
N
O
R
M
Y
E
L
=
M
A
N
1
1
8
1
3
0
0
L
1
D
S
X
#
2
#
3
#
4
#
1
QFC-C
D
S
X
P
W
R
D
S
X
D
S
X
T
S
T
A
L
M
A
C
T
A
P
S
G
R
N
=
N
O
R
M
Y
E
L
=
M
A
N
1
1
8
1
3
0
0
L
1
D
S
X
#
2
#
3
#
4
#
1
QFC-C
D
S
X
P
W
R
D
S
X
D
S
X
T
S
T
A
L
M
A
C
T
A
P
S
G
R
N
=
N
O
R
M
Y
E
L
=
M
A
N
1
1
8
1
3
0
0
L
1
D
S
X
#
2
#
3
#
4
#
1
HD-10 BRI Mux
P
O
W
E
R
D
S
X
L
B
K
1
2
3
4
5
6
7
8
9
1
0
D
S
L
1
1
8
1
2
0
0
L
1
HD-10 BRI Mux
P
O
W
E
R
D
S
X
L
B
K
1
2
3
4
5
6
7
8
9
1
0
D
S
L
1
1
8
1
2
0
0
L
1
HD-10 BRI Mux
P
O
W
E
R
D
S
X
L
B
K
1
2
3
4
5
6
7
8
9
1
0
D
S
L
1
1
8
1
2
0
0
L
1
HD-10 BRI Mux
P
O
W
E
R
D
S
X
L
B
K
1
2
3
4
5
6
7
8
9
1
0
D
S
L
1
1
8
1
2
0
0
L
1
T1-OR
P
W
R
D
S
X
L
B
K
L
P
A
L
M
T
X
R
X
6
V
+
–
A
P
S
T
X
M
O
N
A
C
T
G
R
N
=
N
O
R
M
Y
E
L
=
M
A
N
R
X
1
1
8
1
3
1
0
L
1
T1-OR
P
W
R
D
S
X
L
B
K
L
P
A
L
M
T
X
R
X
6
V
+
–
A
P
S
T
X
M
O
N
A
C
T
G
R
N
=
N
O
R
M
Y
E
L
=
M
A
N
R
X
1
1
8
1
3
1
0
L
1
T1-OR
P
W
R
D
S
X
L
B
K
L
P
A
L
M
T
X
R
X
6
V
+
–
A
P
S
T
X
M
O
N
A
C
T
G
R
N
=
N
O
R
M
Y
E
L
=
M
A
N
R
X
1
1
8
1
3
1
0
L
1
T1-OR
P
W
R
D
S
X
L
B
K
L
P
A
L
M
T
X
R
X
6
V
+
–
A
P
S
T
X
M
O
N
A
C
T
G
R
N
=
N
O
R
M
Y
E
L
=
M
A
N
R
X
1
1
8
1
3
1
0
L
1
HTU-C
1
1
8
1
1
0
1
L
1
P
W
R
D
S
X
T
X
E
Q
R
X
T
X
M
O
N
R
X
T
S
T
L
P
1
L
P
2
A
L
M
A
C
T
GRN=NORM
YEL=MAN
T
X
R
X
L
IN
K
V.35 RX
V
.3
5
T
X
D
A
T
A
V
O
I
C
E
B
A
T
T
P
W
R
/
N
E
T
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 19
© 2002, ADTRAN, Inc. Total Access 600 Series User Manual
5. CONFIGURING THE TOTAL ACCESS 600
System Info
The 6
<67(0
,
1)2
menu provides basic information about the unit and contains data fields for editing information.
Figure 3 displays the submenus available when you select this menu item.
Figure 3. System Information Menu
>System Name
Provides a user-configurable text string for the name of the TA 600. This name can help you distinguish between dif-
ferent installations. You can enter up to 31 characters in this field, including spaces and special characters (such as an
underbar). This name will appear on the top line of all screens.
>System Location
Provides a user-configurable text string for the location of the TA 600. This field is to help you keep track of the actual
physical location of the unit. You can enter up to 31 characters in this field, including spaces and special characters
(such as an underbar).
>System Contact
Provides a user-configurable text string for a contact name. You can use this field to enter the name, phone number,
or email address of a person responsible for the TA 600 system. You can enter up to 31 characters in this field, includ-
ing spaces and special characters (such as an underbar).
>Unit Name
Product-specific name for the product assembly.
>CLEI Code
CLEI code for the product assembly.
Total Access 600 Series User Manual © 2002, ADTRAN, Inc.
Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B
Page 20
>Part Number
ADTRAN part number for the product assembly.
>Serial Number
Serial number of the product assembly.
>Firmware Revision
Displays the current firmware revision level of the controller.
>Bootcode Revision
Displays the bootcode revision.
>System Uptime
Displays the length of time since the TA 600 system reboot.
>Date/Time
Displays the current date and time, including seconds. This field can be edited. Enter the time in 24-hour format (such
as 23:00:00 for 11:00 pm). Enter the date in mm-dd-yyyy format (for example, 10-30-1998).
Each time you reset the system, this value resets to 0 days, 0 hours, 0 min and 0 secs.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
