Kenwood R-K711 User manual

R-K711

COMPACT HI-FI COMPONENT SYSTEM

INSTRUCTION MANUAL

D

ecl

a

Declaration of Conformity with regard to

the EMC Directive 2004/108/EC

Manufacturer:

Kenwood Corporation

2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan

EU Representative’s:

Kenwood Electronics Europe BV

Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands

2

R-K711

Safety precautions

WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE,

IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS

VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO

CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT

THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING)

INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.

The marking of products using lasers

The marking this product has been classi ed as Class 1. It means that

there is no danger of hazardous radiation outside the product.

Location: Back panel

CLASS 1

LASER PRODUCT

Safety Precautions

Before Applying Power

Caution: Read this page carefully to ensure safe operation.

Units are designed for operation as follows.

Australia .....................................................AC 240 V only

Europe ........................................................AC 230 V only

Safety Precautions

3

English

A product and cart combination

should be moved with care. Quick

stops, excessive force, and uneven

surfaces may cause the product and

cart combination to overturn.

5. Ventilation

– Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of

the product and to protect it from overheating,

and these openings must not be blocked or

covered. The openings should never be blocked

by placing the product on a bed, sofa, rug, or

other similar surface. This product should not be

placed in a built-in installation such as a bookcase

or rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

6. Power Sources

– This product should be operated only from the

type of power source indicated on the product. If

you are not sure of the type of power supply to

your home, consult your product dealer or local

power company.

7.

CAUTION – Polarization

– This product may be equipped with a polarized

alternating-current line plug (a plug having one

blade wider than the other). This plug will  t into

the power outlet only one way. This is a safety

feature. If you are unable to insert the plug fully

into the outlet, try reversing the plug. If the plug

should still fail to  t, contact your electrician to

replace your obsolete outlet. Do not defeat the

safety purpose of the polarized plug.

IMPORTANT SAFETY INSTRUCTIONS

Caution: Read this page carefully to ensure safe operation.

Read Instructions

– All the safety and operating instructions should

be read before the product is operated.

Retain Instructions

– The safety and operating instructions should be

retained for future reference.

Heed Warnings

– All warnings on the product and in the operating

instructions should be adhered to.

Follow Instructions

– All operating and use instructions should be

followed.

1. Cleaning

– Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a damp cloth for cleaning.

2. Attachments

– Do not use attachments not recommended by the

product manufacturer as they may cause hazards.

3. Water and Moisture

– This product shall not be exposed to dripping

and splashing – for example, near a bath tub,

wash bowl, kitchen sink, or laundry tub; in a wet

basement; or near a swimming pool; and the like.

Do not place an object containing liquid, such as a

 ower vase, on the appliance.

4. Accessories

– Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may

fall, causing serious injury to a child or adult, and

serious damage to the product. Use only with a

cart, stand, tripod, bracket, or table recommended

by the manufacturer. Any mounting of the product

should follow the manufacturer’s instructions, and

should use a mounting accessory recommended

by the manufacturer.

Continued to next page

R-K711

Safety Precautions

4

8. Power Cord Protection

– Power-supply cords should be routed so that

they are not likely to be walked on or pinched

by items placed upon or against them, paying

particular attention to cords at plugs, convenience

receptacles, and the point where they exit from

the product.

9. Lightning

– For added protection for this product during a

lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the

wall outlet and disconnect the antenna or cable

system. This will prevent damage to the product

due to lightning and power-line surges.

10. Overloading

– Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can result

in a risk of  re or electric shock.

11. Object and Liquid Entry

– Never push objects of any kind into this product

through openings as they may touch dangerous

voltage points or short-out parts that could result

in a  re or electric shock. Never spill liquid of any

kind on the product.

12. Servicing

– Do not attempt to service this product yourself

as opening or removing covers may expose you

to dangerous voltage or other hazards. Refer all

servicing to quali ed service personnel.

13. Damage Requiring Service

– Unplug this product from the wall outlet and

refer servicing to quali ed service personnel under

the following conditions:

a) When the power-supply cord or plug is

damaged,

b) If liquid has been spilled, or objects have

fallen into the product,

c) If the product has been exposed to rain or

water,

d) If the product does not operate normally by

following the operating instructions.

e) If the product has been dropped or

damaged in any way, and

f) When the product exhibits a distinct change

in performance – this indicates a need for

service.

g) If an abnormal smell or smoke is detected.

14. Replacement Parts

– When replacement parts are required, be sure

the service technician has used replacement parts

speci ed by the manufacturer or have the same

characteristics as the original part. Unauthorized

substitutions may result in  re, electric shock, or

other hazards.

15. Safety Check

– Upon completion of any service or repairs to

this product, ask the service technician to perform

safety checks to determine that the product is in

proper operating condition.

16. Wall or Ceiling Mounting

– This product should be mounted to a wall

or ceiling only as recommended by the

manufacturer.

17. Heat

– This product should be situated away from heat

sources such as radiators, heat registers, stoves, or

other products that produce heat. Do not place a

 aming object, such as a candle or lantern, or near

the product.

18. Power Lines

– An outside antenna system should not be located

in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall

into such power lines or circuits. When installing an

outside antenna system, extreme care should be

taken to keep from touching such power lines or

circuits as contact with them might be fatal.

IMPORTANT SAFETY INSTRUCTIONS

Safety Precautions

English

Safety Precautions

5

19. Outdoor Antenna Grounding

– If an outside antenna or cable system is

connected to the product, be sure the antenna or

cable system is grounded so as to provide some

protection against voltage surges and built-up

static charges. Article 810 of the National Electrical

Code, ANSI/NFPA 70, provides information with

regard to proper grounding of the mast and

supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding

conductors, location of antenna-discharge

unit, connection to grounding electrodes, and

requirements for the grounding electrode.

Information on Disposal of Old Electrical

and Electronic Equipment (applicable for

EU countries that have adopted separate

waste collection systems)

Products with the symbol (crossed-

out wheeled bin) cannot be

disposed as household waste.

Old electrical and electronic

equipment should be recycled at

a facility capable of handling these

items and their waste byproducts.

Contact your local authority for details in

locating a recycle facility nearest to you.

Proper recycling and waste disposal will

help conserve resources whilst preventing

detrimental e ects on our health and the

environment.

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL

ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC – NATIONAL ELECTRICAL CODE

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

ANTENNA LEAD IN WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUND CLAMP

ELECTRIC SERVICE

EQUIPMENT

GROUND CLAMPS

Notes:

1. Item 7 is not required except for grounded or

polarized equipment.

2. Item 19 complies with UL in the U.S.A.

R-K711R-K711

6

What the R-K711 Can Do

Wide range of recording formats

Play Discs

As well as music CDs, the R-K711 will also play discs containing recorded audio  les (MP3/

WMA/AAC).

Supports a host of component types

External Input Terminals

As well as analog input terminals for record players or cassette decks, the R-K711 also features

an input terminal for digital audio players.

It even has a digital input terminal with sampling rate converters so that you can use

components such as digital tuners.

Create the perfect sound space for your installation setting

Room Equalizer

The R-K711 automatically optimizes the audio settings for your room layout and system

location.

You simply set up the microphone supplied with the R-K711 in the listening position and then

start up the Room Equalizer.

Realistic audio playback with near-original sound

Supreme EX

Original Kenwood audio enhancement technology that reproduces the high-bandwidth

component in the original sound produces incredibly realistic audio that restores almost all

the nuances of the original performance.

This reproduces high-range bands of 20 kHz and higher from audio CD or digital input.

It also reproduces the high-range bands lost through data compression when you play audio

 les (MP3/WMA/AAC).

Choose your favorite audio quality

Digital Sound Equalizer Function

This includes “TONE/TURN OVER”, which you can use to select detailed audio characteristics for

the low-, mid- and high-range bands, as well as “D-BASS” which allows you to add super-bass

functionality.

You can also register 3 pre-loaded “sound presets” for each setting, making it even easier to

select your favorite sound quality.

English

7

Contents

Procedures by Input Source

Maintenance

P.25

P.71

Be sure to read these precautions.

Safety Precautions ……………………… 2

Before Applying Power …………… 2

IMPORTANT SAFETY INSTRUCTIONS

………………………………………… 3

Accessories ………………………………… 8

Installing the System ……………………… 9

Connecting the System ………………… 10

Component Names and Functions …… 14

How to Use This Manual ………………… 18

Basic Operation ………………………… 20

Important Information ………………… 22

Before Using the

System

This chapter explains how to connect and use

the system with the di erent input sources.

CD

Receiving Broadcast Stations

RDS (Radio Data System)

External Components

D.AUDIO

•

This chapter explains how to store and

maintain your system so that it continues to

give pleasure for many years to come.

Messages

Troubleshooting

Glossary of Terms

Care and Storage

Speci cations

•

Audio Settings

P.47

This chapter explains how to tailor the system

to your audio preferences.

ROOM EQ (Room Equalizer)

Digital Sound Equalizer

Sound Presets

Supreme EX

BALANCE

•

Component Settings

P.61

This chapter explains how to select the settings

for the R-K711.

Setting the Timer

Display Settings

Setting the Time

Auto Power Save (A.P.S.)

•

To ensure safety, read the items carrying

this marking carefully.

R-K711

8

AM loop antenna

(1)

FM indoor antenna

(1)

Remote control

(RC-RP0705E: 1)

Batteries for the remote control

(R03: 2)

Check that all accessories are present in the package.

Microphone for Room Equalizer

(Cord length: Approx. 5 m: 1)

Accessories

If any accessories are missing, or if the unit is damaged or fails to operate, notify your dealer immediately. If the unit was

shipped to you directly, notify your shipper immediately. Kenwood recommends that you retain the original carton and

packing materials in case you need to move or ship the unit in the future. Keep this manual handy for future reference.

English

9

Always install the system on a  at, stable surface. When installing the system on a stand of some sort, be sure to check the

strength of the stand.

The magnets used in the speakers may cause color irregularities on TV or PC screens. Do not set up the speakers too close

to a TV or PC.

z

Notes on installing the system

The sound will vary depending on the positioning of the speakers. To get the best possible sound quality, note the guidelines

below.

Ensure that the surroundings for the left and right speakers are as identical as possible. Set up the left and right speakers

away from the wall and hang thick curtains on any windows to minimize echoes or reverberation.

Place the left and right speakers as far apart as possible.

Position the speakers at the same height as your ears when you are using the system.

z

Getting the best acoustic e ect

Left speaker Right speakerMain unit

Observe the following cautions when installing the system. Insu cient heat radiation may

build up internal heat and cause a malfunction or re hazard.

Do not place an object that may hinder heat radiation on the system.

Leave the spaces speci ed below around the cabinets of the main unit.

Top panel: 50 cm or more

Side panel: 10 cm or more

Back panel: 10 cm or more

Install the system so that the power outlet is easily accessible from the user, and unplug the

power cord from the power outlet immediately in case of a trouble.

Note that the power supply to the system is not shut down completely by simply setting the

power key to OFF.

To shut down the power supply completely, it is required to unplug the power cord.

z

CAUTION

Installing the System

10

R-K711

Main Connections

Connecting the System

To AC wall outlet

AM loop antenna

1 Connect the lead to the [FM75Ω]

terminal.

2 Find the location that gives the best

reception.

3 Fix the antenna in place.

FM indoor antenna

Room equalizer microphone

AC power cord

Right speaker

Left speaker

Ensure that all the cords are securely connected. Loose or incomplete connections may

result in noise interference or no sound at all.

For more

information, see

“Connecting

Other Accessories

(Commercially

Available Units)” on

P.12-13.

Insert the plug  rmly

all the way into the

AC wall outlet.

z

Caution for

connection

Do not plug the AC power cord into an AC wall outlet until all the connections are completed.

Before disconnecting any cords or cables, always turn the main unit o and unplug the power cord

from AC wall outlet.

Push into the slot.

11

English

Connecting the System

The antenna supplied with the system is a basic antenna for indoor use. For stable signal reception, the use

of an outdoor antenna (commercially available unit) is recommended. To connect an outdoor antenna,  rst

remove the indoor antenna.

Connecting the FM indoor antenna

Connecting the speaker cordsz

Preparing the ends of the speaker cords

Twist the plastic sleeve on the end of the cord as you

pull it o .

z

Notes on connecting the

speaker cords

Never short-circuit the positive (+) and negative (–) ends of

the speaker cords. (Do not touch the + and – cords together.)

Mistakenly reversing the positive and negative polarity will

result in unnatural sound and unclear sound source (e.g. musical

instruments) locations.

Connecting the speakers

1234

Microcomputer malfunctions

If the system is connected correctly and still does not operate

normally or shows display errors, reset the microcomputer. (P.75)

The antenna supplied with the system is for indoor use. Place it as far as possible away from the main unit, your

TV set, the speaker cords and the power cord and point it in the direction that gives the best reception.

Connecting the AM loop antenna

123

Connecting the antenna cord

Connect the AM antenna cord to the [AM]

and [MGND] terminals, as shown on the

right.

z

R-K711

12

Connecting Other Accessories (Commercially Available Units)

Connecting the System

When a related system component is connected, read the instruction manual for that component also.

Ensure that all the cords are securely connected. Loose or incomplete connections may result in noise interference

or no sound at all.

z

Caution for outdoor antenna

installation

Since antenna installation necessitates skill and experience, always consult

your dealer before installation. The antenna should be placed at a distance

from the power distribution wires. Otherwise, an electric shock accident may

occur if the antenna falls down.

D.AUDIO IN

Connect digital audio players to the [D.AUDIO IN] terminal

on the rear panel of the main unit.

If you connect a Kenwood player that supports digital

audio link using the dedicated cable, you can control the

player from the main unit and the remote control. (P.44) It

can be connected using a 3.5 mm stereo mini-plug cable

(commercially available unit).

When you are not using the digital audio player, unplug

the mini-plug cable from the main unit.

z

Digital audio player

PHONO IN

Connect record players with MM cartridges to the [PHONO

IN] terminal on the rear panel of the main unit.

The [M] (earth) terminal is used to reduce noise

reduction when an analog record player is connected

to the system. It is not an earth terminal for safety

purposes.

Record players with built-in equalizer ampli ers should

be connected to the [AUX IN] terminal.

You cannot connect a record player with an MC cartridge

directly to the main unit. Connect a dedicated equalizer

ampli er to the record player and then connect it to the

[AUX IN] terminal.

z

Record player

(with MM cartridge)

Audio OUT

Signal

earth lead

English

13

Connecting the System

SUB WOOFER PRE OUT

Connect a subwoofer (such as the optional SW-40HT) to

the [SUB WOOFER PRE OUT] terminal on the rear panel

of the main unit.

Powered Subwoofer

PHONES

Plug headphones equipped with a 3.5 mm stereo mini-

plug into the [PHONES] jack on the front panel of the main

unit.

DIGITAL IN (OPTICAL)

Digital tuner, etc.

Optical digital output

(PCM signals)

Connect the optical digital output terminals on components

such as digital tuners to the [DIGITAL IN (OPTICAL)]

terminal on the rear panel of the main unit.

Set the digital audio output on connected components

to “PCM”.

z

AUX IN

VCR, etc.

Audio OUT

Connect the audio OUT terminals on components such as

VCRs to the [AUX IN] terminal on the rear panel of the main

unit.

TAPE REC OUT/PLAY IN

Audio OUT

Audio IN

Cassette deck

Connect the audio output and audio input terminals on the

cassette deck to the [TAPE PLAY IN] and [TAPE REC OUT]

terminals respectively on the rear panel of the main unit.

14

R-K711

D.AUDIOE (P.44)

Main unit

Standby Mode

While the [STANDBY/TIMER] indicator on the main unit

is lit, the unit is using a very weak current to maintain the

built-in memory. This is called Standby mode. When the

main unit is in this mode, you can turn it on using the

remote control.

One-touch Operation

The main unit features a convenient one-touch operation

function. When the main unit is in Standby mode, you can

turn it on by pressing the [TUNER/BAND], [CDE] or

[D.AUDIOE] key. If there is a disc in the unit, playback

begins.

Component Names and Functions

Power (P.21)

Turns the unit on or o (Standby).

STANDBY/TIMER indicator

Red: Lights in normal Standby mode.

Orange: Lights in Timer Standby mode.

Display (P.15)

Sound indicators

LCD open/close (P.21, 26)

VOLUME (P.20)

CDE (P.21, 26)

TUNER/BAND (P.36)

INPUT SELECTOR

(P.21, 42)

PHONES jack

(P.13)

Remote sensor

(P.17)

F/TUNING MODE (P.27, 37, 45)

G/I, J/H

(P.27, 36, 37, 45)

SOUND SELECTOR

(P.51–55)

ENTER

Fixes a setting.

MODE

Switches to setting modes

for various settings.

SPRM EX indicator (P.59)

ROOM EQ MODE indicator (P.51)

TONE indicator (P.53)

CD tray (P.21, 26)

SOUND CONTROL (P.51–55)

Dial lighting (P.67)

15

English

Display

Displays shown in this manual

may di er from the actual displays.

Component Names and Functions

Displays numbers and text.

TUNED

Lights when you are tuned to a radio station. (P.37)

ST.

Lights when you are receiving a stereo broadcast. (P.37)

AUTO

Lights during auto tuning. Turns o during manual

tuning. (P.37)

RDS

Lights when an RDS broadcast is received. (P.40)

PTY

Lights in the PTY search mode.

Flashes when the sound is

muted. (P.20)

Lights when an audio  le or

folder is selected. (P.31)

Displays the sound

preset number. (P.56, 57)

Lights when measurement of the

room’s acoustic characteristics is

completed. (P.49)

Lights when a super-bass (D-BASS)

level is selected. (P.52)

Displays the level meters.

You can turn this display on or o .

(P.67)

Displays the clock, the elapsed time or the frequency.

FM

Lights in FM reception mode. (P.37)

AM

Lights in AM reception mode. (P.37, 69)

TTL

Lights during CD playback when the elapsed time and

remaining time for the entire disc are displayed. (P.28)

kHz

Displays the AM reception frequency.

MHz

Displays the FM reception frequency.

Lights when Auto Power Save

(A.P.S.) is set. (P.70)

Lights during CD

playback. (P.26)

Lights when there is a CD in

the CD tray. (P.26)

Lights when CD

playback is paused.

(P.27)

Lights when the sleep timer is

set. (P.62)

Lights when the program timer

is set. (P.63)

Lights in CD program

playback mode. (P.32)

Lights in CD random

playback mode. (P.34)

REPEAT

Lights during CD all-tracks

repeat playback. (P.35)

REPEAT ONE

Lights during CD single-track

repeat playback. (P.35)

R-K711

16

Remote control

Remote control keys with the same names as keys on the

main unit have the same functions as the main unit keys.

Component Names and Functions

Selects tracks or

stations.

Sets the MODE function.

(P.27, 36, 45)

Sets display settings.

(P.67)

Numbers.

Selects tracks or stations.

(P.32, 36, 40, 41)

Selects folders.

(P.31, 45)

Selects external

components.

(P.21, 42)

Sets the timer.

(P.62–66)

Turns the unit on or o (Standby).

(P.21)

Turns the unit on or o (Standby).

Turns the main unit on when the

[STANDBY/TIMER] indicator on the

main unit is lit.

Selects the information shown

on the display.

(P.28, 29, 40)

Selects the CD playback mode.

(P.32, 34, 35)

Adjusts the volume.

(P.20)

Sets the sound quality or

component.

Stops playback.

Selects the radio station

selection mode. (P.27, 37, 45)

Skips back or forward through

the tracks and selects the radio

station. (P.27, 37, 45)

Sets the sound quality.

(P.48–58)

Selects input source.

Starts playback.

(P.21, 26, 36, 44)

Fixes a setting.

Clears the settings.

Performs PTY search.

(P.32, 33, 41)

English

17

Loading the remote control batteries

1 Remove the

battery cover.

2 Load the R03 batteries

supplied with the system.

3 Close the battery

cover.

Check the polarity of the

batteries (U, V) when

loading them.

z

The batteries supplied with the system are only for operation checking and may only last for a short

time.

When replacing the batteries, always load 2 new batteries.

z

Component Names and Functions

After plugging the main unit into the AC

wall outlet, press the power [K] key on

the remote control unit to turn the system

on.

Once the system is turned on, press the key

for the function you want to use.

Point the remote control at the remote

sensor when using it.

The remote control may not operate

correctly if direct sunlight or light from a

high-frequency  uorescent lamp (such

as an inverter type) is shining on the

remote sensor. If this happens, install

the main unit in a di erent location to

avoid this sort of malfunction.

z

Approx.

6 m

Approx.

30°

Approx.

30°

Using the remote control

26

R-K711

Press the [L] key on the main unit to open the CD tray and

then load the CD.

1

Playing a CD

Press the [CDE] key.

3

Load and play a CD.

If you have already loaded a disc, just press the [CDE] key to turn the system on and

begin playback.

z

Load the disc that the labeled side

faces upwards and the disc sits

snugly in the tray.

z

The system displays text information

such as track names and album names

for CD-TEXT discs.

z

Press the [L] key on the main unit to close the CD tray.

The “READING” message ashes while the unit is reading the information on the

CD.

2

Playing a CD. As well as normal playback, you can use folder playback, program playback, random

playback and repeat playback.

CD

Track number

during playback

A CD is loaded in

the tray.

Elapsed time of the

track being played

When you play the following types of disc, track numbers may not be displayed

correctly.

Discs recorded in Mix mode*

Discs recorded in multiple sessions

Discs recorded in mixed formats of CD-DA format and formats that are not

music data

Mix mode is a mode in which the CD-DA format is combined with audio le such as MP3,

WMA and AAC.

z

–

*

CD tray

18

R-K711

While this system can be controlled

from either the remote control or

the main unit, the explanations

in this manual primarily describe

operation procedures using the

remote control.

Operation procedure

How to Use This Manual

The displays shown in this instruction

manual may di er from the actual

displays.

z

Display shown during

or after an operation

Remote control keys

used in the procedure

45

D.AUDIO

English

Adjusting the Digital Audio Player Input Level R P.46

Audio Settings R P.47 onwards

z

Operations during digital audio player playback

Skipping forward/back

Hold down the [G] or

[H] key.

Hold down the

[G/I] or

[J/H] key.

Pausing and resuming playback

Press the [D.AUDIOE]

key.

Press the [D.AUDIOE]

key.

Stopping playback

Press the [F] key. Press the [F] key.

Skipping tracks/ skipping back/ skipping to the start

Skip a track

Press the [H] key.

Press the [G] key

two or more times in

succession.

Press the [G] key once.

Skip back to the previous track

Press the [J/H] key.

Press the [G/I]

key two or more times in

succession.

Press the [G/I]

key once.

Return to the start of the track

Playing the tracks in the previous/next folder

To go to the previous folder,

press the [PREV.] key.

To go to the next folder, press

the [NEXT] key.

These functions may not work

with some digital audio player

models.

z

19

English

Explains the procedure for CDs.

Operation icons

How to Use This Manual

Explains the procedure for digital

audio players.

Explains the procedure for the radio.

Explains the procedures for external

components.

Explains how to set the sound quality.

Explains how to set up component

units.

Explains how to carry out system

maintenance.

Related functions that

may also be helpful

Explanations of remote

control procedures

Explanations of

main unit procedures

20

R-K711

Preparations

Check the connections. (P.10–13)

Have the remote control ready. (P.17)

Raises the

volume

Lowers the

volume

Lowers the volume

Raises the volume

Mute

Press this key again to unmute the

sound.

z

This section describes some basic procedures for using the system, such as tuning the radio and playing audio

from a CD, a digital audio player and an external component.

Adjusting the volume

Basic Operation

Page is loading ...

Kenwood R-K711 User manual

Kenwood R-K711 User manual

Related papers

Other documents