Powermate PMC401856 User manual

Brand: Powermate

Model: PMC401856

Category: Power generators

Type: User manual

Page is loading ...

*3.5 HP Briggs & Stratton engine

*Receptacles on endbell

*Battery charger

*1.35 gallon plastic fuel tank

*Spark arrester

*Brushless generator

A .120 V, 15 Ampere Duplex Receptacle

15 amps of current may be drawn from each half of the

receptacle. However, total power drawn must be kept within

nameplate ratings.

B.Circuit Breaker

The receptacles are protected by an AC circuit breaker. If

the generator is overloaded or an external short circuit occurs,

the circuit breaker will trip. If this occurs, disconnect all

electrical loads and try to determine the cause of the problem

before attempting to use the generator again. If overloading

causes the circuit breaker to trip, reduce the load. NOTE:

Continuous tripping of the circuit breaker may cause

damage to generator or equipment. The circuit breaker may

be reset by pushing the button of the breaker.

C.Engine Switch

D.Battery Charger

NOT RECOMMENDED FOR USE WITH GEL PACK,

SEALED OR SMALL (MOTORCYCLE) BATTERIES.

These generators contain an additional circuit used for

battery charging purposes. A DC receptacleis provided on the

control panel. A battery charging cable equipped with a

matching plug for this receptacle has been supplied with the

unit.

The battery charger on this generator is referred to as an

unregulated taper charger - the most widely used in the market

today. The amount of current flowing will depend on the

charging voltage and battery's state of charge. As the battery

becomes more fully charged, the output current to the battery

decreases and nearly becomes constant. Taper chargers are

intended to be used with the provision that they will be

disconnected from the battery after a maximum time on charge.

Normally a period of 30 to 120 minutes is sufficient to recharge

a weak battery. The charge level of the battery should be

checked periodically.

CAUTION: This battery charging system is

intended to recharge weak batteries, not to

"boost start" vehicles. Do not overcharge

battery or leave battery unattended.

Note: When the battery charger circuit is in use, the AC

capacity is reduced by 180 watts. Make sure the combined

load is within the rated limits.

Before charging a storage battery, check the electrolyte

fluid level in all the cells. Add distilled water to each cell, if

necessary, to bring the level back up to the manufacturer's

required level.

WARNING: Storage batteries give off

EXPLOSIVE hydrogen gas while charging.

Do not allow smoking, open flames,sparks,

or spark producing equipment in the area

while charging.

Use cables approved for battery charging. Connect a red

clip to the positive terminal of the battery. Connect a black clip

to the negative terminal of the battery. Connect the other end

of the cable to the DC receptacle on the generator panel. After

the battery is fully charged, remove the battery charging cable

from the generator and then disconnect from the battery posts.

WARNING: Battery electrolyte fluid is

comprised of sulfuric acid that can be very

dangerous and cause severe burns. Do not

allow this fluid to contact eyes, skin, clothing,

etc. If contact or spillage does occur, flush

the area with water immediately.

WARNING: Do not continue to charge a

battery that becomes hot or is fully charged.

DC CIRCUIT BREAKER: The maximum current available

from the battery charger circuit is 15 amps. An automatic DC

circuit breaker has been provided to protect the circuit from

overloads and assure that the battery gets recharged. If an

overload occurs, the circuit breaker will trip. After it cools, it will

automatically reset itself. The battery's maximum rate of

charge will eventually reduce to less than 15amps and then to

zero as the battery approaches a 100 percent state of charge.

English

ENDBELL

MAJOR GENERATOR FEATURES

RECEPTACLE PANEL RECOIL PANEL

English

CAUTION: Keep fuel tank area free of all

debris, water, and ice. Do not block vent.

“Tank must breathe.”

This engine is equipped with a U.S. Forest Service

approved spark arrest muffler. It should periodically be cleaned

to prevent the screen from becoming clogged, which could

hamper engine performance.

To clean, remove the muffler shield. Remove the four

screws and pull the plate with the screen attached. Clean off

any particles with a brush and reinstall. Be sure gasket is in

place.

Check engine oil . . . . . . . . . . . . . . . . . . . . . . Before each use

Change engine oil . . . . . . . . . . . . After first 20 hours and then

every 50 hours of operation

Clean air filter. . . . . . . . . . . . . . . . Every 50 hours of operation

Clean spark plug . . . . . . . . . . . . Every 100 hours of operation

Clean spark arrestor . . . . . . . . . . Every 50 hours of operation

Oil Type. Use new good quality oil such as SC, SD, and

SE grades. The oil to be used depends upon the temperature

at which the engine is operated:

Summer: (temperatures of over 40 degrees F/10 degrees

C) SAE 30 or SAE 10W-30, SAE 10W-40

Winter: (temperatures of below 40 degrees F/10 degrees

C) SAE 20 or SAE 10W-30

Warranty Coverage: Powermate Corporation (the Company)

warrants to the original retail customer in North America that it

will repair or replace, free of charge, any parts found by the

Company or its authorized service representative to be

defective in material or workmanship. This warranty covers the

cost of replacement parts and labor for defects in material or

workmanship.

Not Covered:

· Transportation charges for sending the product to the

Company or its authorized service representative for

warranty service, or for shipping repaired or replacement

products back to the customer; these charges must be

borne by the customer.

Engine is covered exclusively by a separate warranty from

the engine manufacturer, included with the engine Manual.

· Damages caused by abuse or accident, and the effects of

corrosion, erosion and normal wear and tear.

· Warranty is voided if the customer fails to install, maintain

and operate the product in accordance with the instructions

and recommendations of the Company set forth in the

owner's manual, or if the product is used as rental

equipment.

The Company will not pay for repairs or adjustments to the

product, or for any costs or labor, performed without the

Company's prior authorization.

Warranty Period: Two (2) years from the date of purchase on

products used solely for consumer applications; if a product is

used for business or commercial applications, the warranty

period will be limited to one (1) year from the date of purchase.

For warranty service, the customer must provide dated proof of

purchase and must notify the Company within the warranty

period.

For warranty service: Call toll free 800-445-1805, or write

to Powermate Corporation, Product Services, 4970 Airport

Road, P. O. Box 6001, Kearney, NE 68848.

EXCLUSIONS AND LIMITATIONS: THE COMPANY MAKES

NO OTHER WARRANTY OF ANY KIND, EXPRESS OR

IMPLIED. IMPLIED WARRANTIES, INCLUDING

WARRANTIES OF MERCHANTABILITY AND OF FITNESS

FOR A PARTICULAR PURPOSE, ARE HEREBY

DISCLAIMED. THE WARRANTY SERVICE DESCRIBED

ABOVE IS THE EXCLUSIVE REMEDY UNDER THIS

WARRANTY; LIABILITY FOR INCIDENTAL AND

CONSEQUENTIAL DAMAGES IS EXCLUDED TO THE

EXTENT PERMITTED BY LAW.

This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state. Some states

do not allow a disclaimer of implied warranties, or the exclusion

or limitation of incidental and consequential damages, so the

above disclaimers and exclusions may not apply to you.

LIMITED WARRANTY

FUEL TANK VENTING

SPARK ARRESTER MUFFLER

ENGINE MAINTENANCE SCHEDULE

English

CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board and Powermate Corporation (herein "Powermate") are pleased to explain the evaporative emission

control system (EECS) warranty on your 2006 generator. In California, new generators must be designed, built and equipped to meet the

State's stringent anti-smog standards. Powermate must warrant the EECS on your generator for the periods of time listed below, provided

there has been no abuse, neglect or improper maintenance of your generator.

Your EECS includes parts such as: fuel hoses.

MANUFACTURER'S WARRANTY COVERAGE:

This evaporative emission control system is warranted for two years. The warranty period begins on the date the generator is delivered to

an ultimate purchaser.

Powermate warrants to the ultimate purchaser and any subsequent owner that the generator is (i) designed, built and equipped so as to

conform with all applicable regulations; and (ii) free from defects in materials and workmanship that cause the failure of a warranted part

to be identical in all material respects to that part as described in Powermate's application for certification.

If any evaporative emission-related part on your generator is defective, the part will be repaired or replaced by Powermate.

OWNER'S WARRANTY RESPONSIBILITIES:

As the generator owner, you are responsible for performance of the required maintenance listed in your owner's manual. Powermate

recommends that you retain all receipts covering maintenance on your generator, but Powermate cannot deny warranty solely for the lack

of receipts. You should, however, be aware that Powermate may deny you warranty coverage if your generator or a part has failed due to

abuse, neglect or improper maintenance or unapproved modifications.

You are responsible for presenting your generator to an authorized Powermate warranty service center as soon as the problem exists. The

warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question regarding your

warranty coverage, you should call Powermate Product Service at 1-800-445-1805.

DETAILS OF YOUR WARRANTY

Subject to certain conditions and exclusions as stated below, the warranty on emission-related parts is as follows:

(1)Any warranted part that is not scheduled for replacement as required maintenance in the written instructions supplied, is warranted

for the period stated above. If the part fails during the period of warranty coverage, the part will be repaired or replaced by

Powermate according to Subsection (4) below. Any such part repaired or replaced under warranty will be warranted for the

remainder of the period.

(2)Any warranted part that is scheduled only for regular inspection in the written instructions supplied, is warranted for the warranty

period stated above. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period.

(3)Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied, is warranted for

the period of time before the first scheduled replacement date for that part. If the part fails before the first scheduled replacement

date, the part will be repaired or replaced by Powermate according to Subsection (4) below. Any such part repaired or replaced under

warranty will be warranted for the remainder of the period prior to the first scheduled replacement date for the part.

(4)Repair or replacement of any warranted part under the warranty provisions herein must be performed at an authorized Powermate

warranty service center at no charge to the owner.

(5)The generator owner will not be charged for diagnostic labor that is directly associated with diagnosis of a defective,

emission-related warranted part, provided that such diagnostic work is performed at an authorized Powermate warranty service

center.

(6)Powermate is liable for damages to other engine or generator components proximately caused by a failure under warranty of any

warranted part.

(7)Throughout the generator warranty period stated above, Powermate will maintain a supply of warranted parts sufficient to meet the

expected demand for such parts.

(8)Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge

to the owner. Such use will not reduce the warranty obligations of Powermate.

(9)Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on

or modified parts by the ultimate purchaser will be grounds for disallowing a warranty claims. Powermate will not be liable to war

rant failures or warranted parts caused by the use of a non-exempted add-on or modified part.

(10)The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty

coverage if the generator has been abused, neglected or improperly maintained, and such abuse, neglect or improper maintenance

was the direct cause of the need for repair or replacement of the part.

WARRANTED PARTS:

The following emission warranty parts list is covered:

Fuel Hose.

Page is loading ...

Ref No Part No

ArtNº / P

Art NúmPièces Núm Description Description DescripciónQty

1Note AEngine 3.5 hp B&SMoteurMotor1

20050448.01Engine AdapterAdaptateur de moteurAdaptador motor1

30000901.01Bolt Whz 5/16-24 x 5/8Boulon, whzPerno, whz4

40062623StatorStatorEstator1

50062621RotorRotorRotor1

6Note BWasher, Lock 5/16Rondelle, plateArandela, cierre1

70035022Bolt, Rotor 5/16-24 x 5-1/8Boulon, rotorPerno, rotor1

80062008Assy, Stator BracketAssemblage, supportEnsamble, soporte estator1

de stator

90063148EndbellCouvre-enroulementPlaca lateral1

10Note BBolt, Hex HD 1/4-20 x 3Boulon, hexPerno, hex2

110062006Screw, Torx T30 1/4-20 x 3.25Vis, Torx T30Tornillo, Torx T302

120040832Nut, Nyloc 1/4-20Ecrou, nylocTuerca, nyloc7

130062011Assembly, handle bracketAssemblage, support deEnsamble, soporte mango1

manche

140062069Shield, heatÉcran de chaleurPantalla para el calor1

150063147Panel, recoilPanneauPanel1

160061952Bracket, recoilSupportSoporte1

170062015Screw, Torx T30 1/4-20 Vis, TorxTornillo, Torx12

180049892Gasket, Muf B&SJoint silJunta, silenciador1

190062002Muffler B&SSilencieuxSilenciador1

20Note BWasher, Lock 1/4Rondelle, contre-ecrouArandela, cierre2

210049161Screw SHC 1/4-20 x 5/8VisTornillo2

220049846ClipAttachePresilla2

230047774Foot, Rubber 106-WPied, caoutchoucPie, caucho2

240062007Screw, Torx T30 1/4-20 x 1.50 Vis, Torx T30Tornillo, Torx T302

250062850Panel, wiredTableau, câblePanel con cable1

260062020Screw #6-19 x .50VisTornillo4

27Note CAssy, Fuel TankAssemblage, réservoirEnsamble, tanque combustible1

280063162Cap, FuelCapuchon, réservoir d’essence Tapa, combustible1

29Note BWasher, Flat 5/1 6Rondelle, plateArandela, plana3

30Note BNut 5/16-18 EcrouTuerca3

310050144Bolt, Whz 1/4-20 x 3/8Boulon, whzPerno, whz2

320062673Fuel BushingBague d’essenceBuje de combustible1

330050298Switch, rockerInterrupteurInterruptor1

340008854Lug, GroundPatte, mise à la terreOreja, tierra1

35Note BBolt, Hex 1/4-20 x 1-1/2Boulon, hexPerno, hex1

360062093Washer Nylon .25 IDRondelle en nylonArandela del nilón4

390062856Panel Side CoverPanneau de couverture côtéCubierta lateral panel1

400062023Shield, MufflerTole, silencieuxEscudo, silenciador1

410062021Screw, Torx T20 #10-24 x .50Vis, Torx T20Tornillo, Torx T208

420049953Circuit Breaker, 12ADisjoncteursCortacircuitos1

430051367.01Fuel FilterEpurateur d’essenceFiltro de combustible1

440049920Fuel Shut Off, InlineFermeture d’essenceApagado combustible, en línea1

450035857Clamp, Hose 1/2”Crampon, tuyauAbrazadera, manguera2

460055955Screw CRPH #10-24 x .50VisTornillo1

470062197Bushing, breatherBagueBuje1

480061835Assembly, duck bill fuel valveAssemblage, Robinet de Ensamble, Válvula combustible1

carburant

490047806CapacitorCondensateurCondensador1

500048677Bridge DiodePont DiodePuente Diodo1

510047706Clamp, Nylon 1/2”Crampon, nylonAbrazadera, nylon1

520001537Screw Hex Hd 8-32 x 3/8VisTornillo1

530051291Assembly, Battery CableCâble pour batterieBatería, cable 1

540055853Assembly, Fuel lineEssence ligne assembléeTubería de alimentación de combustible1

asamblea

PARTS LIST / LISTE DES PIÈCES / LISTA DE PIEZAS

Page is loading ...

4970 Airport Road

P. O. Box 6001

Kearney, NE 68848

1-800-445-1805

1-308-237-2181

Fax 1-308-234-4187

are registered trademarks of The Coleman Company, Inc. used under license.

Powermate ® is a registered trademark of Powermate Corporation.

sont des marques déposées de The Coleman Company, Inc. utilisées sous licence.

Powermate® est une marque déposée de Powermate Corporation.

son marcas comerciales registradas de The Coleman Company, Inc. utilizadas bajo licencia.

Powermate ® es una marca comercial registrada de Powermate Corporation.

Coleman® and

Coleman® et

Coleman® y

Powermate PMC401856 User manual

Brand: Powermate

Model: PMC401856

Category: Power generators

Type: User manual

Download PDF

report

in other languages

français: Powermate PMC401856 Manuel utilisateur
español: Powermate PMC401856 Manual de usuario

Powermate PMC401856 User manual

Powermate PMC401856 User manual

in other languages

Related papers

Other documents