Eiki LC-XIP2600 Owner's manual

Interactive Function Manual

CMOS Sensor

Contents of the Accessory Bag....................................................................i

Accessories Introduction............................................................................ii

Operation Guide for Windows OS ........................................................... 1

Operation Guide for Mac OS .................................................................. 12

Troubleshooting ........................................................................................ 18

i

Contents of the Accessory Bag

Please make sure that following items are included in the Accessory Bag. If any

items are missing, contact your dealer.

1. Accessory Bag 2. Pointer

3. Light Pen 4. Batteries (AA)

5. Batteries (AAA) 6. Hanging String

ii

Contents of the Accessory Bag

Accessories Introduction

Function Key on the "Pointer Body"

LED Lamp

Button: Mouse Left Key

Before using the Pointer.

Screw the Rod part into the pointer body

rmly please.

How to use this

While pressing the button Infra Red

signal is emitted from the tip of the rod

and the CMOS sensor in the projector

detects the position of it. While the IR is

emitted, the LED Lamp also lights red.

1) Position the tip of pointer on the

screen.

2) Push the button to click the target as a

mouse or push and hold the button to

draw a line as a pen.

Back side Front side

iii

Contents of the Accessory Bag

Accessories Introduction

Function Key on the "Light Pen"

Touch sensor pen tip

LED Lamp

Button: Mouse Left Key

How to use this

While the button is pressed or the tip is

pressed to a hard screen Infra Red signal

is emitted from the tip of the pen and the

CMOS sensor in the projector detects the

position of it. While the IR is emitted, the

LED Lamp also lights red.

1) Position the tip of pen on the screen.

2) Push the button to click the target as a

mouse or push and hold the pen to the

hard screen to draw a line as a pen.

CAUTION

Bottom cap with switch function.

Because the tip has a sensor switch inside,

when it is tilted or pushed, it consumes

battery. In order to prevent this happens

while transportation the bottom cap is given

with switch function. By rotating the cap by

90 degree counterclockwise, the above can

be prevented.

Back side Front side

1

Operation Guide for Windows OS

1. System Requirements

To ensure the interactive function work properly, please check your

computer to see if it meets the following conditions.

System Requirements

OS Required Microsoft Windows 2000(SP4)/XP(SP2)/Vista

Processor Type Intel Pentium IV or above

RAM 256 MB above

Min. Free disk space 30 MB

CD-ROM Driver & USB 2.0 port available

2. LightPen Software Installation

Step 1: Insert the "Owner's Manual" CD-ROM into the CD drive.

Step 2: Copy the "LightPen Software for Windows" folder in the CD-

ROM and paste it on your PC's hard disk drive.

Step 3: Take out the CD-ROM from the CD drive.

Step 4: Find "LightPen.exe" le in the "LightPen Software for Windows"

folder on your PC's hard disk drive.

Step 5: Create the short-cut icon for the "LightPen.exe", and put it on the

desktop for your ease.

Note: The software can not be executed from CD-ROM, because the

calibration data cannot be stored in the CD-ROM.

Interactive function is provided by "LightPen" software.

2

Operation Guide for Windows OS

Note for Windows Vista

(a) Click mouse right key on "LightPen.exe" or the short-cut icon for

"LightPen.exe" and then click mouse left key to select "Properties".

LightPen Software for Windows

LightPen.exe

LightPen System

64

80

Send To

Play

Properties

3

Operation Guide for Windows OS

v

(b) Select "Compatibility" sheet and add check marks to the following.

"Run this program in compatibility mode for:

Windows XP (Service Pack 2)",

"Disable desktop composition".

Then select "Apply".

4

Operation Guide for Windows OS

3. Initial Setup for Interactive Function

3.1 Connect supplied USB cable between XIP2600 and the PC.

3.2 Execute "LightPen" software by double-checking the "LightPen.

exe" or the short-cut icon for the "LightPen.exe". Then the icon for

"LightPen" appears in the task bar and the tool bar appears on the

right side of the screen.

3.3 Select Distance

Step 1: Click mouse right key on "LightPen" in the task bar.

Step 2: Select "Projection Distance".

5

Operation Guide for Windows OS

Step 3: Choose the projection distance from pop-up menu

(>3m,>2m,<2m), and then select "OK".

3.4. Calibration

Step 1: Click mouse right key on "LightPen" in the task bar.

Step 2: Select "Calibration".

Step 3: According to the projector setting condition, select

projection method of "Desktop"or "Ceiling".

6

Operation Guide for Windows OS

3.4 Calibration

Step 4: Push the button on the "Pointer" or "Light Pen" (pending on

the screen size) while placing the tip on the center of green

target. The color of target changes black from green. Then

next green target appears on the upper middle area of the

screen. Repeat the same until all of 13 targets change black.

In order to carry out the calibration smoothly be sure to

expose the tip of the "Pointer" or "Light Pen" to the sensor

near the projection lens. If the tip is lit up by the light from

the projector, the sensor can detect the tip's position well.

Note:

If the screen and XIP2600 stay where they are and if the same PC is

used with the same resolution, Distance setting or Calibration is no

longer required from next time.

7

Operation Guide for Windows OS

Function of each icon in the Tool bar

Tool bar position

To position tool bar on the right or left side of screen.

Mouse

To change function to Computer Mouse.

Pen

To change function to Pen.

Eraser

To erase drawn line.

Fineness of pen

To select the neness of pen.

Color of pen

To select the color of pen.

Eraser all

To erase drawings on the screen all at once.

Save les

To save the current page into le in computer.

Redraw

To recall the previous drawing (or erasing) you've made.

Virtual keyboard

To open virtual keyboard.

4. How To Use Interactive Function

8

Operation Guide for Windows OS

In the Mouse mode(default)

Mouse pointer can be moved by the Pointer or the Pen.

The left click or double click can be done by pushing the button.

The right click can be done as follows.

At rst place the mouse pointer on the target.

Then place the tip of "Pointer" or "Light Pen" on the top or the bottom

edge slightly outside the projected image, then press the button on it.

4. How To Use Interactive Function

9

Operation Guide for Windows OS

4. How To Use Interactive Function

Note

There is another quick way to change the position of the tool bar or hide/

show it.

Place the tip of "Pointer" or "Light Pen" on the left or right edge slightly

outside the projected image, then press the button on it.

In the Pen mode

A line can be drawn with the Pointer or the Pen. In order to continue

to emit IR light from the tip, press and hold the button on the Pointer

during drawing please. In the case of Pen while the tip is pressed against

the hard screen, it continues to emit IR light.

The thickness and color of the line can be changed.

The drawn image can be saved with the back ground image.

10

Operation Guide for Windows OS

5. How to nish Interactive function

5.1 Select "Mouse" mode by selecting "Mouse" icon in the tool bar.

5.2 Click mouse right key on LightPen Icon in the task bar.

11

Operation Guide for Windows OS

5.3 Click mouse left key to select "Exit".

5.4 Click mouse left key to select "OK" in the conrmation dialog.

(This can be down either on the screen or on the PC.)

12

Operation Guide for Mac OS

1. System Requirements

To ensure the interactive function work properly, please check your

computer to see if it meets the following conditions.

System Requirements

OS Required Mac OS X v10.4.11- v10.5 or above

Processor Type Intel processor or Power PC

RAM 512 MB RAM or above

Hard Disk At least 10 MB of hard disk space

Media Device At least 4x CD-ROM or DVD-ROM

At least USB 2.0

2. LightPen Software Installation

Step 1: Insert the "Owner's Manual" CD-ROM into the CD drive.

Step 2: Copy the "LightPen Software for Mac OS" folder in the CD-

ROM and paste it on your PC's hard disk drive.

Step 3: Create the short-cut icon for "LightPen" le in the "LightPen

Software for OS" folder and put it on the desktop for your ease.

Interactive function is provided by "LightPen" software.

13

Operation Guide for Mac OS

3. Initial Setup for Interactive Function

3.1 Connect supplied USB cable between XIP2600 and the PC.

3.2 Execute "LightPen" software by clicking the "LightPen" or the short-

cut icon for the "LightPen". Then the icon for "LightPen" appears in

the task bar and the tool bar appears on the right side of the screen.

3.3 Select Distance

Step 1: Click mouse key on "LightPen" in the menu bar.

Step 2: Select "Projection Distance".

14

Operation Guide for Mac OS

Step 3: Choose the projection distance from pop-up menu

(>3m,>2m,<2m), and then select "OK".

3.4 Calibration

Step 1: Click mouse key on "LightPen" in the task bar.

Step 2: Select "Calibration".

15

Operation Guide for Mac OS

Step 3: Push the button on the "Pointer" or "Light Pen" (pending on

the screen size) while placing the tip on the center of green

target. The color of target changes black from green. Then

next green target appears on the upper middle area of the

screen. Repeat the same until all of 9 targets change black.

In order to carry out the calibration smoothly be sure to

expose the tip of the "Pointer" or "Light Pen" to the sensor

near the projection lens. If the tip is lit up by the light from

the projector, the sensor can detect the tip's position well.

Note:

If the screen and XIP2600 stay where they are and if the same PC is

used with the same resolution, Distance setting or Calibration is no

longer required from next time.

16

Operation Guide for Mac OS

Function of each icon in the Tool bar

4. How To Use Interactive Function

Tool bar position

To position tool bar on the right or left side of screen.

Mouse

To change function to Computer Mouse.

Pen

To change function to Pen.

Eraser

To erase drawn line.

Fineness of pen

To select the neness of pen.

Color of pen

To select the color of pen.

Eraser all

To erase drawings on the screen all at once.

Save les

To save the current page into le in computer.

Redraw

To recall the previous drawing (or erasing) you've made.

Virtual keyboard

To open virtual keyboard.

Page is loading ...

Eiki LC-XIP2600 Owner's manual

Eiki LC-XIP2600 Owner's manual

Related papers

Other documents