Chief PAC526FBP2 Installation guide

Brand: Chief

Model: PAC526FBP2

Category: Wall & ceiling mounts accessories

Type: Installation guide

This manual is also suitable for

In-Wall Accessory Boxes

I N S T A LLA T I O N I N S T R U C T I O N S

PAC525/526

PAC525 PAC526

Installation Instructions

PAC525/526

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and

subsidiaries (collectively “Milestone”), intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING: Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all components are

properly assembled and installed using the instructions

provided.

WARNING: Failure to provide adequate structural strength

for this accessory can result in serious personal injury or

damage to equipment! It is the installer’s responsibility to

make sure the structure to which this accessory is attached

can support five times the combined weight of all equipment.

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components located in the accessory does not exceed

10 lbs (4.5 kg).

WARNING: Use this mounting system only for its intended

use as described in these instructions. Do not use

attachments not recommended by the manufacturer.

WARNING: For indoor use only.

IMPORTANT ! : The PAC525/526 mounts are designed to

be mounted to a 2” x 4” wood stud wall, 16” on center, or 2” x

4” -25ga (minimum) steel studs wall.

NOTE: Ambient Temperature - The manufacturer's maximum

ambient temperature is 120°F (49°C) and minimum ambient

temperature is 40°F (4°C) so that the installer is able to

determine acceptability of use of accessories and components

in the operating.

NOTE: Spacings - Minimum spacings between the 120 Vac

power components and the A/V components shall be main-

tained for safe operation of the equipment when installed in

accordance with the National Electric Code, ANSI/NFPA

70-2008.

NOTE: When selecting a Listed 120 Vac Receptacle for use as

the main power source for the PAC Series boxes (to power the

A/V equipment), make sure that AC Receptacle is rated at least

15A and it is used in the building's AC branch circuit that is

connected to a circuit breaker rated at least 15A. Do not

connect more than 12A from the Receptacle.

In the U.S., the equipment shall be installed per the applicable

requirements of the National Electrical Code, ANSI/NFPA 70.

In Canada, the equipment shall be installed per the applicable

requirements of the Canadian Electrical Code, CSA C22.1.

--SAVE THESE INSTRUCTIONS--

DIMENSIONS

PAC525

PAC526

10.26

260.7

15.40

391.1

9X .75 X .25

ZIP TIE ANCHOR HOOKS

9.00

228.6

7.00

177.8

4.50

114.3

2.57

65.2

3.88

98.4

3.00

76.2

7.00

177.8

4.50

114.3

2.57

65.2

14.25

362

3.00

76.2

10.93

277.6

2.57

65.2

4.75

120.7

.38

9.5

1.38

34.9

1.13

28.6

3.73

94.9

1.72

[43.7]

1.36

[34.5]

0.87

[21.8]

15.51

394.1

15.40

391.1

14X .75 X .25

ZIP TIE ANCHOR HOOKS

14.25

362

4.75

120.7

3.00

76.2

10.93

277.6

.38

9.5

1.38

34.9

2.57

65.2

14.25

362

5.00

127

11.75

298.5

7.13

181

.82

20.8

1.82

46.2

2.57

65.2

1.13

28.6

3.73

94.9

3.88

98.4

1.72

[43.7]

1.36

[34.5]

0.87

[21.8]

Installation Instructions PAC525/526

LEGEND

Installation Instructions

PAC525/526

Tighten Fastener

Apretar elemento de fijación

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Loosen Fastener

Aflojar elemento de fijación

Befestigungsteil lösen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis à pointe cruciforme

Mark level line

Flathead Screwdriver

Pencil Mark

Marcar con lápiz

Stiftmarkierung

Marcar com lápis

Segno a matita

Potloodmerkteken

Marquage au crayon

Drill Hole

Perforar

Bohrloch

Fazer furo

Praticare un foro

Gat boren

Percez un trou

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Remove

Quitar

Entfernen

Remover

Rimuovere

Verwijderen

Retirez

Precision hand cut surface

TOOLS REQUIRED FOR INSTALLATION

PARTS INCLUDED

#2 Phillips

3/16”

1/4”

Stud Sensor

Punch

optional

OPTIONAL PARTS PER CUSTOM CONFIGURATION (NOT INCLUDED)

Conduit Connectors

Conduit Pipe 1/2”, 1” or 1-1/4”

Box Cover

Box Frame Install Box

3” x 2” Switch Box

(2” deep)

Raco #420 or equiv.

Electrical

Outlet

Steel Handy Box

Cover, Duplex

Raco #864 or equiv.

Zip Ties

Template/Temporary Cover

Earthing symbol IEC 60418 No. 5019

affixed adjacent to grounding terminal

Grounding screw installed at factory

1 2 3 4 5

#2 Flathead

1/4 - 20 x 2 1/2” Screw

(4x)

#6 - 32 x 3/8” Screw

(8x)

Security Hex Key

#10 - 32 x 3/8”

#6 - 32 Hex Nut

(8x)

#6 x 1 1/2”

Button Security Screw

3/8” Flat Washer

(4x)

* Items may vary depending on specific model number.

Installation Instructions PAC525/526

PAC525

PAC5 2 6

INSTALLATION

The PAC525/526 is intended for use both in installations

where an existing finished drywall wall is present, and where

the wall surface has not been finished and the structural studs

are exposed. The wall then must be finished around the

opening of the box after the box has been installed.

PAC525/526 Project Planning

Identify a suitable wall location for the accessory.

Using a stud sensor, locate and mark studs.

Identify possible structural conflicts (electrical wiring,

plumbing, gaslines, HVAC).

WARNING: ELECTRICAL SHOCK HAZARD! CUTTING

OR DRILLING INTO ELECTRICAL WIRES OR CABLES

CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!

ALWAYS make certain area behind mounting surfaces is

free of electrical wires and cables before cutting, drilling or

installing fasteners.

WARNING: EXPLOSION AND FIRE HAZARD! CUTTING

OR DRILLING INTO GAS PLUMBING CAN CAUSE

DEATH OR SERIOUS PERSONAL INJURY. ALWAYS

make certain area behind mounting surfaces is free of gas,

water, waste or any other plumbing before cutting, drilling

or installing fasteners.

Determine installation type. Housing is designed to fit

between two adjacent wall studs, or onto a drywall

surface.

Plan box and component needs.

Sketch diagrams provided:

Drywall attachment only

Pre-sheetrock attachment

Stud & drywall attachment

Determine all components needed.

Conduit Pipe

Conduit Connectors (large and small)

Electrical Box(es) (3” x 2”)

Steel Electrical Box Cover(s)

Zip Ties

Electrical Outlet(s)

WARNING: All wiring should be performed

by a licensed electrician following all local

codes and ordinances.

Installation Instructions

PAC525/526

PAC525/526 Site Preparation

Using a level, draw a horizontal line at lower edge of

install site.

A - STUD ATTACHMENT - create exploratory hole to

confirm edge of stud/studs.

B - DRYWALL ATTACHMENT - mark horizontal cut

locations ensuring a minimum 1/2” distance from

each stud.

Loosely attach components and conduit (cut to length)

to box to ease fitting into wall opening.

Align on lower edge drawn line (A) and horizontal

marking for inside stud location (B).Use enclosed

template or housing as a template, drawing line

around top and sides of housing.

Cut along outside

edge of line using

utility knife.

Remove drywall.

NOTE:

Cutting past corners

weakens the cleats’

ability to hold securely.

Remove knock-outs in box as predetermined in

step 5.

PAC525/526 Box Preparation

10 Once wall opening is completed, check stud depth. If 3.5” or greater, proceed to step 11. If less than 3.5” deep, modify depth

of box as follows before proceeding: CAUTION: Injury may occur on sharp edges. Carefully discard the removable tabs.

A - Remove box flange by removing screws.

B - Snap off removable tabs

at perforations provided.

C - Reinstall box flange. Reattach screws.

PAC525/526 Box Installation

Feed attached conduit through cut-out and insert box

into opening in wall. Tighten component connections.

B B

Installation Instructions PAC525/526

Use supplied #6 screws (H)

and nuts (F) to assemble

the switch box

Mark the four corners.

CAUTION:

Avoid sharp edges.

Wire/Cable Management - Use “integrated zip-tie hook”

in back wall of box to organize and secure cables and

AV components.

Install template as temporary cover if needed to protect

from debris by folding tabs in and inserting into opening.

Gather wires and route through cover opening. Install

cover, screw fasteners(2) into place to secure and

complete enclosure.

Secure box into

place by methods

chosen.

DRYWALL

ATTACHMENT:

Slide locking

cleats into place.

Tighten screws

to secure.

STUD ATTACHMENT:

Drill pilot holes (optional) into studs through mounting

holes in box. Wood studs - use 3/16” bit. If steel studs

- use 1/4” bit. Install with 1/4 - 20 x 2 1/2” screws (E)

into pilot holes.

NOTE:

Box may be installed with outer flange removed

for a pre-sheetrock open stud mount configuration.

NOTE:

Save flange for

reattachment after

sheetrock is installed.

Plastic

Spacer

Mounting

Screw

Cover

PAC525/526 Final Finishing

Modify enclosure cover before attaching. Break away tab(s)

to allow wire exit from box and meet ventilation needs.

NOTE:

Locate front edge of box extended

beyond studs by thickness of

sheetrock to be used.

Installation Instructions

PAC525/526

Installation Instructions PAC525/526

PAC525/526 Installation Instructions

Installation Instructions PAC525/526

USA/International A 6436 City West Parkway, Eden Prairie, MN 55344

P800.582.6480 / 952.225.6000

F877.894.6918 / 952.894.6918

Europe A Franklinstraat 14, 6003 DK Weert, Netherlands

P+31 (0) 495 580 852

F+31 (0) 495 580 845

Asia Pacific A Office No. 1 on 12/F, Shatin Galleria

18-24 Shan Mei Street

Fotan, Shatin, Hong Kong

P852 2145 4099

F852 2145 4477

Chief, a products division of

Milestone AV Technologies

8800-002517 Rev00

2014 Milestone AV Technologies

www.chiefmfg.com

03/14

Installation Instructions PAC525/526

Chief PAC526FBP2 Installation guide

Brand: Chief

Model: PAC526FBP2

Category: Wall & ceiling mounts accessories

Type: Installation guide

This manual is also suitable for

Download PDF

report

Chief PAC526FBP2 Installation guide

This manual is also suitable for

Chief PAC526FBP2 Installation guide

Related papers

Other documents