Lifeplus DBJ-32A User manual

ICE MAKER

PRODUCT USE GUIDE

hoose LifePlus, Choose A Plus Life.

DBJ-32A

Please read this instruction

carefully before use.

Damage caused by

improper operation is not

covered by the warranty.

Please Note

After opening the box, please do not use it

immediately. Let the ice machine stand upright

for 24 hours first.

This is because the ice machine has experienced a long time of shipping. This

will cause uneven distribution of refrigerant in the compressor. If you use it

immediately after receiving it, it may cause damage to the compressor, and

we will not bear this compensation.

Please pay special attention to the red text

GENERAL INFORMATION PAGE3

TABLE OF CONTENTS

SECTION 1

INSPECTION AFTER DELIVERY PAGE3

PRECAUTIONS FOR SAFE OPERATION PAGES5-6

SPECIFICATION PAGE7

SECTION 2

SECTION 3

SAFETY PRECAUTIONS PAGE8

PARTS & ACCESSORIES PAGE9

PRECAUTIONS PAGES12

SECTION 5

INSTALLATION STEPS OF ICE MAKER PAGES13-14

SECTION 6

DISCHARGE SEWAGE STEPS PAGES15

OPERATION INTRODUCTION PAGES19-20

SECTION 7

ERROR & TROUBLESHOOTING PAGE17

FAULT SELF-DIAGNOSIS PAGES18-20

CLEANING & MAINTENANCE PAGE22

SECTION 4

CONTROL PANEL PAGE10-11

SECTION 8

SECTION 9

GENERAL INFORMATION

1. This ice maker uses advanced production technology and skilled processes,

as well as the strict quality inspection, guarantees the excellent performance of

the ice maker.

2. The compressor of the ice maker is very strong and efficient, it makes the ice

making speed of the ice machine faster.

3. The design of stainless steel makes it look more fashionable and beautiful.

4. The automatic microcomputer control system can make the ice making and

harvest process automatically. It also has fault detection function, make it easier

to troubleshoot. Common faults and solutions are on page 21 - 26. If you still

can't solve the faults, please contact us via [email protected]. We will

reply you within 24 hours. Please tell us your order ID in the email.

INSPECTION AFTER DELIVERY

Thank you for choosing our ice maker. In order to ensure a happy shopping

experience for you, please pay attention to the following matters after opening

the package:

1. Dents on the ice machine;

2. Missing parts, such as drain hose...

If the above matters occur, please contact us via [email protected] for

solutions. Please tell us your order ID in the email.

[email protected]

- 3 -

- 4 -

[email protected]

WARNING DIAGRAMS AND OPERATING

SAFETY INSTRUCTIONS

processes, as well as the strict quality inspection, guarantees the excellent performance

The core component of the ice maker "compressor" we use well-known brand product,

, to protect your legitimate rights,

- 5 -

[email protected]

PRECAUTIONS FOR SAFE OPERATION

!AFTER RECEIVIN G THE ICE M AKER, LET THE ICE M AKER STAND UPRIGHT FOR 24

HOURS FIRST. OTHERWISE THE COM PRESSOR M AY BE DAM AGED .

Please do not use it outdoors. If necessary, be sure to make the ice maker

waterproof. And avoid direct sunlight, high temperature may cause ice machine failure.

Do not disassemble, repair or modify the ice maker without permission. Fire hazard

or personal injury may be caused by work errors without professors or professional

guidance.

Do not directly spray water on the ice maker, it may cause electric shock or short

circuit.

Do not locate the ice maker in a humid place or a place prone to splashing water, to

avoid the damage to the insulating material, so to prevent leakage or electric shock.

Do not earth the ice maker through a gas pipe, a water main, a telephone line, or a

lightning rod.

Do not insert metallic materials such as wires into the air vents, passage or exhaust

vents of the ice maker, to avoid electric shock or personal injury due to accidental

movement of active parts.

Do not put volatile or flammable substances into the ice maker. Storage of such

substances may cause explosion or fire hazard.

The ice maker should be repaired by professional technicians or under their

guidance.

Please keep the ice maker on a flat ground to avoid equipment failure and danger

caused by inclination.

Please use a power supply that is specified on the ice maker's label.

Disconnect the main plug from the supply socket when the ice maker gets failures.

Continued abnormal operation may cause electric shock or fire hazard.

- 6 -

[email protected]

Please remove the dust from the supply socket before plugging the power plug into it,

to avoid fire hazard.

Keep the ice maker free of obstructions and keep the ventilation open.

Do not store combustion sprays, volatile or flammable substances in the ice maker.

Storage of such substances may cause an explosion or fire hazard.

Do not use the ice maker when handling toxic or hazardous materials or radioactive

materials, as it may harm health and damage the environment.

Disconnect from the main socket before cleaning, maintaining or servicing the

appliance. To prevent electric shock or personal injury.

Do not use other electrical appliances in the ice machine. This appliance contains

flammable materials, and must be handled and recycled by qualified personnel and

institutions when discarded.

Do not damage the refrigeration circuit.

Use a grounded outlet to prevent electric shock. If there is no, the grounded socket

device must be assembled by a professional technician. The unit must be positioned so

that the plug is accessible.

Some models use flammable refrigerants and flammable foaming

agents, so beware of fire (The product is marked "Warning fire"). When

the appliance is abnormal, it must be repaired by professional personnel

and institutions.

- 7 -

. It may cause leakage or electric shock after the ice

[email protected]

TECHNICAL PARAMETERS

Specification

Rated power / frequency

Ice making current

Ice harvest current

Ice cubes number / tray

Protection against electric shock

Water inlet mode

Tap water inlet pressure

Refrigerant / Weight

Insulation materials

Applicable environmental level

Gross / net weight

Product size

DBJ-32A

120V/60Hz

1.9A

2.7A

32

ⅠLevel

Tap water / bucket water

100-800KPa

R134a / 0.24lb

Cyclopentane (C5H10)

SN / N

53.86 / 46.75 LBS

13.78*14.09*24.8 INCH

- 8 -

[email protected]

SAFETY PRECAUTIONS

1. The voltage of this ice maker is: 120V / 60Hz. Please solve the voltage problem before

installing.

2. In order to protect the compressor, do not start the ice maker again within 5 minutes

after power off.

3. Better not not plug other appliances in the same socket.

4. If the power cord is damaged, in order to avoid danger, it must be repaired or

replaced by professionals.

5. The working voltage of the ice machine is higher than 36V. Please do not disassemble

the ice machine when it is working.

WARNING:

Do not operate the ice maker when there is a gas leak in its environment. Fire hazard

may occur due to sparks caused by unplugging or plugging or the start-stop controlled by

the temperature controller, the gas source should be cut off first, and allow air to circulate

to outdoor.

Ⅰ

- 9 -

[email protected]

PARTS & ACCESSORIES

DBJ-32A

ICE MAKER

PRODUCT USE GUIDE

Sealing Tape Water Inlet Plug Blue Buckle

Commercial Ice Maker Ice Shovel Water Inlet Hose Drain Hose Instruction

Snap Spring

PRODUCT DIAGRAM

Control panel

Foot Water drain hose

Water inlet Hose

Dust cover of bucket

water inlet hole

Door of ice bin

Hot air outlet

Sewage outlet

Drain the water in the water

tank after cleaning Drain the melted water in

the ice bin

Note: the ice machine is gravity drainage, which requires

drainage holes or bottles to collect the water after the ice

melts.

- 10 -

[email protected]

CONTROL PANEL

1.

Ice full indicator (Red): When it lights up, it means that the ice machine is full of

ice. Please take out the ice for use or put them in a frozen place for storage.

2.

Water shortage indicator (Red): When it lights up, it means that the ice maker is

short of water. You can't turn on the ice machine until it goes out.

3. Small size

indicator (Green): Tell you that the ice thickness you choose to make

now is the thinnest.

4. Mednium size

indicator (Green): Tell you that the ice you choose to make now is

medium thick.

5. Large size

indicator (Green): Tell you that the thickness of the ice you choose to

make now is the thickest.

6. On/Off button

: Click to turn on or turn off the ice maker. (Do not press for

seconds, just click.)

7. Ice thickness selection button

: Click to choose ice thickness, the ice thickness you

choose will be reflected on the size indicator light.

12345

76

FULL

WATER

SM L

Press the ice thickness selection button for 5 seconds, the machine will enter the self-cleaning mode.

- 11 -

[email protected]

ICE MAKING OPERATION STEPS

Step 1: Plug in the power, at this time, all the indicator lights will be on. Just wait a few

seconds.

Step 2: Adjust the valve according to the water inlet mode.

Step 3: Hook up the water source and let water enter slowly. (Refer to page 13-14)

Step 4: W ait for a few minutes, the water shortage indicator will go out.

Step 5: After the water shortage indicator light goes out, click size button to select the

thickness of the ice.

Step 6: Click the button, the hot air outlet in front of the ice maker will blow out hot

air. Wait for a few minutes, the ice maker will automatically start making ice cubes.

SELF-CLEANING OPERATION STEPS

Step 1: Plug in the power, at this time, all the indicator lights will be on. Just wait a few

seconds.

Step 2: Adjust the valve according to the water inlet mode.

Step 3: Hook up the water source and let water enter slowly. (Refer to page 13-14)

Step 4: W ait for the water shortage indicator to go out. (At this time, it is recommended

to cut off the water source. Otherwise, when you discharge the sewage, the water will

keeps entering the ice machine.)

Step 5: After the water shortage indicator light goes out, press size button for 5

seconds to enter self-cleaning mode.

FORCE HARVEST ICE

During the ice making process, press the On/ Off button for 3 seconds, the ice maker

will harvest ice in advance. It will continue to run the next ice-making cycle after

completion.

NOTE:

1. When each batch of ice falls into the ice bin, please shovel it into 32 small ice cubes with the ice

shovel to hold more ice in the ice bin. Otherwise, the ice bin may be full soon.

2. It is recommended to put the excess ice in the ice bags and store them in an freezer.

- 12 -

℉

[email protected]

PRECAUTIONS BEFORE INSTALLATION

CORRECT OPERATION

When using the ice maker for the first time or using it continuously, please follow

below rules!

Use an independent water source for the ice maker, and check regularly to prevent low

water pressure or pipe blocked.

Do not store anything in the ice bin, this will make the ice machine difficult to clean or

the pipes blocked.

When using the plastic door of the ice bin, open and close it gently, and do not hit the

door, and please also close the door after take out the ice.

The ice maker should be kept away from heat sources, strictly forbidden to use it in

super high or super low temperature environment. Away from direct sunlight to avoid

affecting the heat dissipation of the unit.

The ice machine is not waterproof, so please don't wash it directly with a lot of water.

You can use wet or dry rags.

If you will not use this ice maker for a long time, it should be powered on for 4-6 hours

every 2 months to prevent damage.

Avoid sunlight and rain Good ventilation Placement should be stable

- 13 -

, and check regularly to prevent low

The ice maker should be kept away from heat sources, strictly forbidden to use it in high

[email protected]

Step 1: Hook up the drain hose

1.Pull out the water outlet plug (Not

sewage outlet plug)

2.Insert the drain hose and install the

snap spring to fix the drain hose.

Step 2: Adjust the valve and insert the water inlet hose

Installation steps of tap water inlet mode

1. Wrap the sealing tape

around the faucet

2.Insert the white water

inlet hose

1.Adjust the direction of the

valve to be perpendicular

to the water pipe (tap water

inlet mode)

2.Tighten the water pipe

with the connector

3.Fix the water inlet hose

with a blue buckle

Step 3: Hook up the water source

If the complimentary

connector does not

fit your faucet,

please buy it in your

local store.

- 14 -

[email protected]

Installation steps of bucket water inlet mode

Step 1: Hook up the drain hose

1.Pull out the water outlet plug (Not

sewage outlet plug)

2.Insert the drain hose and install the

snap spring to fix the drain hose.

Step 2: Adjust the valve to the bucket water inlet mode

Step 3: Install the water jug

1.Adjust the valve to the direction

parallel to the water pipe.

(bucket

water inlet mode)

1.Variety of water jugs are

applicable. The diameter of the

water jug outlet needs to be less

than 3.2 inches. If water cannot

enter, try lifting the jug several

times to exhaust the air.

- 15 -

The normal use environment temperature

℉ ℉ ℉ ℉

Therefore, it need at least

15cm of space between the front, back, left, and right of your ice maker and wall, good for

must be installed and the ice maker must be earthed. Install the disconnect switch in the

[email protected]

Discharge the sewage after self-cleaning.

Step 1: Place a container that can hold at least 0.2 gallons of water

under the sewage outlet in advance

Step 2: Pull out the sewage outlet plug slowly

Step 3: Plug in the sewage outlet plug again

NOTE: Please cut off the water source before starting to

discharge the sewage, otherwise the water will flow out from the

sewage outlet all the time.

Page is loading ...

Lifeplus DBJ-32A User manual

Other documents