Zanussi ZDV14003FA User manual

Page is loading ...

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read the

supplied instructions. The manufacturer is not responsible for any

injuries or damages that are the result of incorrect installation or

usage. Always keep the instructions in a safe and accessible

location for future reference.

CHILDREN AND VULNERABLE PEOPLE SAFETY

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning the use of the

appliance in a safe way and understand the hazards involved.

• Children between 3 and 8 years of age and persons with very

extensive and complex disabilities shall be kept away unless

continuously supervised.

• Children of less than 3 years of age should be kept away

unless continuously supervised.

• Do not let children play with the appliance.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the door

is open.

• Children shall not carry out cleaning and user maintenance of

the appliance without supervision.

GENERAL SAFETY

• This appliance is intended to be used in household and similar

applications such as:

– farm houses; staff kitchen areas in shops, offices and other

working environments;

– by clients in hotels, motels, bed & breakfast and other

residential type environments.

• Do not change the specification of this appliance.

• The operating water pressure (minimum and maximum) must be

between 0.5 (0.05) / 8 (0.8) bar (MPa)

• Obey the maximum number of 9 place settings.

2

• If the supply cord is damaged, it must be replaced by the

manufacturer, its Authorised Service Centre or similarly

qualified persons in order to avoid a hazard.

• Put the cutlery in the cutlery basket with the sharp ends

pointing down or put them in the cutlery drawer in a horizontal

position with the sharp edges down.

• Do not leave the appliance with the open door unattended to

avoid stepping accidentally onto it.

• Before any maintenance operation, deactivate the appliance

and disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to clean

the appliance.

• If the appliance has ventilation openings in the base, they must

not be covered e.g. by a carpet.

• The appliance is to be connected to the water mains using the

new supplied hose-sets. Old hose sets must not be reused.

SAFETY INSTRUCTIONS

INSTALLATION

WARNING! Only a qualified person

must install this appliance.

• Remove all the packaging.

• Do not install or use a damaged appliance.

• Do not install or use the appliance where the

temperature is less than 0 °C.

• Follow the installation instructions supplied with

the appliance.

• Always take care when moving the appliance as

it is heavy. Always use safety gloves and

enclosed footwear.

• Make sure that the appliance is installed below

and adjacent to safe structures.

ELECTRICAL CONNECTION

WARNING! Risk of fire and electric

shock.

• The appliance must be earthed.

• Make sure that the parameters on the rating

plate are compatible with the electrical ratings

of the mains power supply.

• Always use a correctly installed shockproof

socket.

• Do not use multi-plug adapters and extension

cables.

• Make sure not to cause damage to the mains

plug and to the mains cable. Should the mains

cable need to be replaced, this must be carried

out by our Authorised Service Centre.

• Connect the mains plug to the mains socket

only at the end of the installation. Make sure that

there is access to the mains plug after the

installation.

• Do not pull the mains cable to disconnect the

appliance. Always pull the mains plug.

• This appliance complies with the E.E.C.

Directives.

• UK and Ireland only. This appliance is fitted with

a 13 A mains plug. If it is necessary to change

the mains plug fuse, use only a 13 A ASTA (BS

1362) fuse.

WATER CONNECTION

• Do not cause damage to the water hoses.

• Before connection to new pipes, pipes not used

for a long time, where repair work has been

carried out or new devices fitted (water meters,

etc.), let the water flow until it is clean and clear.

• Ensure that there are no visible water leaks

during and after the first use of the appliance.

• The water inlet hose has a safety valve and a

sheath with an inner mains cable.

3

WARNING! Dangerous voltage.

• If the water inlet hose is damaged, immediately

close the water tap and disconnect the mains

plug from the mains socket. Contact the

Authorised Service Centre to replace the water

inlet hose.

USE

• Do not sit or stand on the open door.

• Dishwasher detergents are dangerous. Obey

the safety instructions on the detergent

packaging.

• Do not drink and play with the water in the

appliance.

• Do not remove the dishes from the appliance

until the programme is complete. Some

detergent may remain on the dishes.

• The appliance can release hot steam if you open

the door while a programme operates.

• Do not put flammable products or items that are

wet with flammable products in, near or on the

appliance.

SERVICE

• To repair the appliance contact an Authorised

Service Centre.

• Use original spare parts only.

DISPOSAL

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the mains

supply.

• Cut off the mains cable and discard it.

• Remove the door catch to prevent children and

pets to get closed in the appliance.

4

EASY START

1

2

3

4

1

On/off button

2

Programme buttons

3

Delay button

4

Indicators

INDICATORS

Indicator Description

End indicator.

Rinse aid indicator. It is always off while the programme operates.

Salt indicator. It is always off while the programme operates.

PROGRAMMES

Programme

Degree of soil

Type of load

Programme phases

Consumption values

1)

Duration

(min)

Energy

(kWh)

Water

(l)

2)

Normal soil

Crockery and

cutlery

• Pre-wash

• Wash 50 °C

• Rinses

• Dry

227 0.778 9.9

3)

All

Crockery, cut-

lery, pots and

pans

• Pre-wash

• Wash from 45

°C to 70 °C

• Rinses

• Dry

45 - 151 0.6 - 1.2 6 - 11

5

Programme

Degree of soil

Type of load

Programme phases

Consumption values

1)

Duration

(min)

Energy

(kWh)

Water

(l)

Heavy soil

Crockery, cut-

lery, pots and

pans

• Pre-wash

• Wash 70 °C

• Rinses

• Dry

160 -

168

1.1 - 1.3 13-14

4)

Fresh soil

Crockery and

cutlery

• Wash 60 °C

or 65 °C

• Rinses

30 0.7 8

5)

All • Pre-wash 14 0.1 4

1) The pressure and the temperature of the water, the variations of the mains supply, the options and the

quantity of dishes can change the values.

2) With this programme you have the most efficient use of water and energy consumption for crockery and

cutlery with normal soil. (Also, it is a standard programme for test institutes).

3) The appliance senses the degree of soil and the quantity of items in the baskets to adjust the tempera-

ture and the quantity of the water and to control the energy consumption and the programme duration.

4) With this programme you can wash a load with fresh soil. It gives good washing results in a short period

of time.

5) Use this programme to quickly rinse the dishes and to prevent the food remains from drying out on the

dishes and to reduce bad odour coming out from the appliance. Do not use detergent with this pro-

gramme.

SETTINGS

PROGRAMME SELECTION MODE

In the programme selection mode, it is possible to

set a washing programme and to enter the user

mode to change the appliance settings.

To enter the programme selection mode:

Press on/off button.

The indicator is on.

If the control panel does not indicate that the

appliance is in the programme selection mode,

follow the Cancel procedure.

CANCEL PROCEDURE

Use Cancel to:

• Cancel a currently running programme.

• Stop the countdown of Delay option.

• Bring the appliance back to the programme

selection mode.

To Cancel:

Press and hold simultaneously

and

until the control panel indicates the appliance is in

the programme selection mode.

USER MODE

The user mode allows changing the following

appliance settings:

• Adjust the level of the water softener according

to the water hardness.

• Activate or deactivate the rinse aid empty

notification.

• Activate or deactivate the acoustic signal

indicating the end of a programme.

• Activate or deactivate AirDry.

Before entering the user mode, make sure the

appliance is in the programme selection mode.

To enter the user mode:

Press and hold simultaneously

and

for at least 3 seconds.

6

The indicators: , , , and

start flashing.

As the appliance stores the saved settings, there is

no need to configure it before every cycle.

ADJUSTING THE WATER SOFTENER

Make sure the appliance is in user mode.

1. Press .

The indicators , , and are off.

The indicator still flashes.

The indicator starts flashing. The number of

flashes indicates the current water softener setting

(e.g. 5 flashes + pause + 5 flashes... = level 5).

2. Press to change the setting. Each

pressing of the button increases the

level number by one. After reaching level 10,

the count starts from level 1.

3. Press on/off to confirm and save the setting.

THE WATER HARDNESS TABLE

German degrees

(°dH)

French degrees

(°fH)

mmol/l Clarke degrees

Water softener

level

47 - 50 84 - 90 8.4 - 9.0 58 - 63 10

43 - 46 76 - 83 7.6 - 8.3 53 - 57 9

37 - 42 65 - 75 6.5 - 7.5 46 - 52 8

29 - 36 51 - 64 5.1 - 6.4 36 - 45 7

23 - 28 40 - 50 4.0 - 5.0 28 - 35 6

19 - 22 33 - 39 3.3 - 3.9 23 - 27

5

1)

15 - 18 26 - 32 2.6 - 3.2 18 - 22 4

11 - 14 19 - 25 1.9 - 2.5 13 - 17 3

4 - 10 7 - 18 0.7 - 1.8 5 - 12 2

<4 <7 <0.7 < 5

1

2)

1) Factory setting

2) Do not use salt at this level.

HOW TO DEACTIVATE THE RINSE AID

EMPTY NOTIFICATION

Make sure the appliance is in user mode.

1. Press .

The indicators: , and are off. The

indicator

still flashes.

The indicator shows the current setting. If on

= rinse aid empty notification is on, if off = rinse aid

empty notification is off.

2. Press to change the setting.

3. Press on/off to confirm and save the setting.

ACTIVATING THE ACOUSTIC SIGNAL AT THE

END OF A PROGRAMME

Make sure the appliance is in user mode.

1. Press .

The indicators: , and are

off. The indicator

still flashes.

The indicator shows the current setting. If on

= the acoustic signal is active. If off = the acoustic

signal is disabled.

2. Press to change the setting.

3. Press on/off to confirm and save the setting.

7

HOW TO DEACTIVATE AIRDRY

AirDry improves the drying results with less energy

consumption.

While the drying phase operates, the

device opens the appliance door. The

door is then kept ajar.

By default, AirDry is activated with all programmes

excluding (if applicable), but it is possible to

deactivate it.

Make sure the appliance is in user mode.

1. Press .

The indicators: , , are off.

The indicator still flashes.

The indicator indicates the current setting. If

on = AirDry is on, if off = AirDry is off.

2. Press to change the setting.

3. Press on/off to confirm and save the setting.

CAUTION! If children have access to

the appliance, it is advised to

deactivate AirDry as opening the door

may pose a danger.

BEFORE FIRST USE

1. Make sure that the current level of the

water softener agrees with the hardness

of the water supply. If not, adjust the level

of the water softener.

2. Fill the salt container.

3. Fill the rinse aid dispenser.

4. Open the water tap.

5. Start a programme to remove any processing

residuals that can still be inside the appliance.

Do not use detergent and do not load the

baskets.

After starting a programme, it may take up to 5

minutes for the appliance to recharge the resin in

the water softener. It seems that the appliance is

not working. The washing phase starts only after

this procedure is completed. The procedure is

repeated periodically.

THE SALT CONTAINER

CAUTION! Use rough salt designed

for dishwashers only. Fine salt

increases the risk of corrosion.

The salt is used to recharge the resin in the water

softener and to assure good washing results in

daily use.

Adding salt

Before the first use, put one litre of water in the salt container.

CAUTION! Water and salt can come out of the salt container during filling. To prevent

corrosion, start a programme immediately after filling the salt container.

8

ADDING RINSE AID

2

1

4

3

2

1

The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot

rinse phase.

DAILY USE

1. Open the water tap.

2. Press the on/off button to activate the

appliance.

Make sure that the appliance is in programme

selection mode.

• If the salt indicator is on, fill the salt

container.

• If the rinse aid indicator is on, fill the rinse

aid dispenser.

3. Load the baskets.

4. Add the detergent.

5. Set and start the correct programme for the

type of load and the degree of soil.

ADDING DETERGENT

2

1

2

0

3

0

A

B

If the programme has a prewash phase, put a small quantity of detergent also in compartment B.

ADDING MULTI-TABLETS

2

1

2

0

3

0

• Do not fill the salt container and the rinse aid dispenser.

• Set the rinse aid dispenser to the lowest position.

9

SETTING AND STARTING A PROGRAMME

The AUTO OFF function

This function decreases energy consumption by

deactivating automatically the appliance when it is

not operating.

The function comes into operation:

• 5 minutes after the completion of the

programme.

• After 5 minutes if the programme has not

started.

Starting a programme

1. Open the appliance door and keep it ajar.

2. Press on/off to activate the appliance. Make

sure the appliance is in the programme

selection mode.

3. Select a programme from the control panel by

pushing a desired programme button.

A related programme indicator is on.

4. Close the appliance door to start the

programme.

The appliance starts working.

Starting programme with Delay option

Make sure the appliance is on and in the

programme selection mode.

1. Select a programme from the control panel.

A related programme indicator is on.

2. Press the button

to delay the programme

start.

The indicator is on.

3. Continue pressing to extend the

countdown (3, 6 or 9 hours).

A related indicator on the control panel indicates

the countdown time.

4. Close the appliance door to start the

countdown.

The programme starts automatically when the

countdown is complete.

Opening the door while the appliance

operates

Opening the door while a programme is running

stops the appliance. It may affect the energy

consumption and the programme duration. After

closing the door, the appliance continues from the

point of interruption.

If the door is opened during the drying

phase, before AirDry automatically

opens it, the programme ends after 30

seconds.

If the door is closed after it is opened

automatically by AirDry in the drying

phase, the programme ends after 3

minutes.

Do not try to close the appliance door

within 2 minutes after AirDry

automatically opens it, as this may

cause damage to the appliance.

End of the programme

When the programme is completed the indicator

is on.

1. Press the on/off button or wait for the AUTO

OFF function to deactivate the appliance. If you

open the door before the activation of AUTO

OFF, the appliance is automatically

deactivated.

2. Close the water tap.

HINTS AND TIPS

GENERAL

The following hints will ensure optimal cleaning and

drying results in daily use and also help to protect

the environment.

• Remove larger residues of food from the dishes

into the waste bin.

• Do not pre-rinse dishes by hand. When needed,

use the prewash programme (if available) or

select a programme with a prewash phase.

• Always use the whole space of the baskets.

• When loading the appliance, make sure that the

dishes can be completely reached and washed

by the water released from the spray arm

nozzles. Make sure that items do not touch or

cover each other.

• You can use dishwasher detergent, rinse aid

and salt separately or you can use the multi-

tablets (e.g. ''3in1'', ''4in1'', ''All in 1''). Follow the

instructions written on the packaging.

• Select the programme according to the type of

load and degree of soil. With the ECO

programme you have the most efficient use of

water and energy consumption for crockery and

cutlery with normal soil.

THE WATER SOFTENER

The water softener removes minerals from the

water supply, which would have a detrimental effect

on the washing results and on the appliance.

10

The higher the content of these minerals, the harder

your water is. Water hardness is measured in

equivalent scales.

The water softener should be adjusted according to

the hardness of the water in your area. Your local

water authority can advise you on the hardness of

the water in your area. It is important to set the right

level of the water softener to assure good washing

results.

USING SALT, RINSE AID AND DETERGENT

• Only use salt, rinse aid and detergent for

dishwasher. Other products can cause damage

to the appliance.

• In areas with hard and very hard water we

recommend to use plain dishwasher detergent

(powder, gel, tablets containing no additional

agents), rinse aid and salt separately for optimal

cleaning and drying results.

• At least once a month run the appliance with the

use of appliance cleaner which is particularly

suitable for this purpose.

• Detergent tablets do not fully dissolve with short

programmes. To prevent detergent residues on

the tableware, we recommend that you use the

tablets with long programmes.

• Do not use more than the correct quantity of

detergent. Refer to the instructions on the

detergent packaging.

WHAT TO DO IF YOU WANT TO STOP USING

MULTI-TABLETS

Before you start to use separately detergent, salt

and rinse aid do the following procedure.

1. Set the highest level of the water softener.

2. Make sure that the salt and rinse aid containers

are full.

3. Start the shortest programme with a rinsing

phase. Do not add detergent and do not load

the baskets.

4. When the programme is completed, adjust the

water softener according to the water hardness

in your area.

5. Adjust the released quantity of rinse aid.

LOADING THE BASKETS

• Only use the appliance to wash items that are

dishwasher-safe.

• Do not put in the appliance items made of

wood, horn, aluminium, pewter and copper.

• Do not put in the appliance items that can

absorb water (sponges, household cloths).

• Remove remaining food from the items.

• Make soft the remaining burned food on the

items.

• Put hollow items (cups, glasses and pans) with

the opening down.

• Make sure that cutlery and dishes do not bond

together. Mix spoons with other cutlery.

• Make sure that glasses do not touch other

glasses.

• Put small items in the cutlery basket.

• Put light items in the upper basket. Make sure

that the items do not move.

• Make sure that the spray arm can move freely

before you start a programme.

BEFORE STARTING A PROGRAMME

Make sure that:

• The filters are clean and correctly installed.

• The cap of the salt container is tight.

• The spray arms are not clogged.

• There is dishwasher salt and rinse aid (unless

you use multi- tablets).

• The position of the items in the baskets is

correct.

• The programme is applicable for the type of load

and for the degree of soil.

• The correct quantity of detergent is used.

UNLOADING THE BASKETS

1. Let the tableware cool down before you

remove it from the appliance. Hot items can be

easily damaged.

2. First remove items from the lower basket, then

from the upper basket.

At the end of the program water can

still remain on the sides and on the

door of the appliance.

11

CARE AND CLEANING

WARNING! Before maintenance,

deactivate the appliance and

disconnect the mains plug from the

main socket.

Dirty filters and clogged spray arms

decrease the washing results. Make a

check regularly and, if necessary,

clean them.

CLEANING THE FILTERS

B

A

C

• Make sure that there are no residues of food or soil in or around the edge of the sump.

• Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides.

• Reassemble the filters (A) and (B).

• Put back the filter (A) in the flat filter (C). Turn it clockwise until it locks.

An incorrect position of the filters can cause bad washing results and damage to the

appliance

CLEANING THE SPRAY ARMS

Do not remove the spray arms. If the holes in the

spray arms are clogged, remove remaining parts of

soil with a thin pointed object.

EXTERNAL CLEANING

• Clean the appliance with a moist soft cloth.

• Only use neutral detergents.

• Do not use abrasive products, abrasive cleaning

pads or solvents.

INTERNAL CLEANING

• Carefully clean the appliance, including the

rubber gasket of the door, with a soft damp

cloth.

• If you regularly use short duration programmes,

these can leave deposits of grease and

limescale inside the appliance. To prevent this,

we recommend to run long duration

programmes at least 2 times per month.

• To maintain the performance of your appliance

at its best, we recommend to use monthly a

specific cleaning product for dishwashers.

Follow carefully the instructions on the

packaging of the product.

12

TROUBLESHOOTING

If the appliance does not start or it stops during

operation, before you contact an Authorised

Service Centre, check if you can solve the problem

by yourself with the help of the information in the

table.

WARNING! Repairs not properly done

may result in serious risk to the safety

of the user. Any repairs must be

performed by qualified personnel.

With some problems the end indicator flashes

intermittently indicating a malfunction.

The majority of problems that can occur can

be solved without the need to contact an

Authorised Service Centre.

Problem and alarm code Possible cause and solution

You cannot activate the appliance. • Make sure that the mains plug is connected to the

mains socket.

• Make sure that there is no damaged fuse in the fuse

box.

The programme does not start. • Make sure that the appliance door is closed.

• If the delay start is set, cancel the setting or wait for

the end of the countdown.

• The appliance has started the procedure to re-

charge the resin inside the water softener. The dura-

tion of the procedure is approximately 5 minutes.

The appliance does not fill with water.

• The end indicator flashes 1 time inter-

mittently.

• Acoustic signal sounds 1 time intermit-

tently.

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply is

not too low. For this information, contact your local

water authority.

• Make sure that the water tap is not clogged.

• Make sure that the filter in the inlet hose is not clog-

ged.

• Make sure that the inlet hose has no kinks or bends.

The appliance does not drain the water.

• The end indicator flashes 2 times inter-

mittently.

• Acoustic signal sounds 2 times inter-

mittently.

• Make sure that the sink spigot is not clogged.

• Make sure that the drain hose has no kinks or

bends.

The anti-flood device is on.

• The end indicator flashes 3 times inter-

mittently.

• Acoustic signal sounds 3 times inter-

mittently.

• Close the water tap and contact an Authorised

Service Centre.

The appliance stops and starts more

times during operation.

• It is normal. It provides optimal cleaning results and

energy savings.

The program lasts too long. • If the delayed start option is set, cancel the delay

setting or wait for the end of the countdown.

13

Problem and alarm code Possible cause and solution

Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten the

adjustable feet (if applicable).

• The appliance door is not centred on the tub. Adjust

the rear foot (if applicable).

The appliance door is difficult to close. • The appliance is not levelled. Loosen or tighten the

adjustable feet (if applicable).

• Parts of the tableware are protruding from the bas-

kets.

Rattling/knocking sounds from inside the

appliance.

• The tableware is not properly arranged in the bas-

kets. Refer to basket loading leaflet.

• Make sure that the spray arms can rotate freely.

The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneous-

ly all the appliances in use. Check the socket am-

perage and the capacity of the meter or turn off one

of the appliances in use.

• Internal electrical fault of the appliance. Contact an

Authorised Service Centre.

Refer to "Before first use", "Daily

use", or "Hints and tips" for other

possible causes.

Once you have checked the appliance, deactivate

and activate the appliance. If the problem occurs

again, contact an Authorised Service Centre.

For alarm codes not described in the table, contact

an Authorised Service Centre.

THE WASHING AND DRYING RESULTS ARE NOT SATISFACTORY

Problem Possible cause and solution

Poor washing results. • Refer to "Daily use", "Hints and tips" and basket loading

leaflet.

• Use more intensive washing programmes.

• Clean spray arm jets and filter. Refer to "Care and Clean-

ing".

Poor drying results. • Tableware has been left for too long inside a closed appli-

ance.

• There is no rinse aid or the dosage of rinse aid is not enough.

Set the rinse aid dispenser to a higher level.

• Plastic items may need to be towel dried.

• For the best drying performance activate AirDry.

• We recommend to always use rinse aid, even in combination

with multi-tablets.

There are whitish streaks or blu-

ish layers on glasses and dishes.

• The release quantity of rinse aid is too much. Adjust the rinse

aid level to a lower level.

• The quantity of detergent is too much.

14

Problem Possible cause and solution

There are stains and dry water

drops on glasses and dishes.

• The released quantity of rinse aid is not sufficient. Adjust the

rinse aid level to a higher level.

• The quality of the rinse aid can be the cause.

The dishes are wet. • For the best drying performance activate AirDry.

• The programme does not have a drying phase or has a drying

phase with low temperature.

• The rinse aid dispenser is empty.

• The quality of the rinse aid can be the cause.

• The quality of the multi-tablets can be the cause. Try a differ-

ent brand or activate the rinse aid dispenser and use rinse

aid and multi-tablets together.

The interior of the appliance is

wet.

• This is not a defect of the appliance. it is caused by the hu-

midity in the air that condenses on the walls.

Unusual foam during washing. • Use the detergent for dishwashers only.

• There is a leak in the rinse aid dispenser. Contact an Author-

ised Service Centre.

Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to

"The water softener".

• Silver and stainless steel cutlery were placed together. Avoid

to put silver and stainless steel items close together.

There are residues of detergent

in the dispenser at the end of the

programme.

• The detergent tablet got stuck in the dispenser and therefore

was not completely washed away by water.

• Water cannot wash away the detergent from the dispenser.

Make sure that the spray arm is not blocked or clogged.

• Make sure that items in the baskets do not impede the lid of

the detergent dispenser from opening.

Odours inside the appliance. • Refer to "Internal cleaning".

Limescale deposits on the table-

ware, on the tub and on the in-

side of the door.

• The level of salt is low, check the refill indicator.

• The cap of the salt container is loose.

• Your tap water is hard. Refer to "The water softener".

• Even using multi-functional tabs use salt and set regeneration

of the water softener. Refer to "The water softener".

• If lime scale deposits still remain, clean the appliance with

appliance cleaners which are particularly suitable for this pur-

pose.

• Try different detergent.

• Contact the detergent manufacturer.

Dull, discoloured or chipped ta-

bleware.

• Make sure that only dishwasher-safe items are washed in the

appliance.

• Load and unload the basket carefully. Refer to basket loading

leaflet.

• Place delicate items in the upper basket.

Refer to "Before first use", "Daily

use" or "Hints and tips" for other

possible causes.

15

TECHNICAL INFORMATION

Dimensions Width / height / depth (mm) 446 / 818 - 898 / 550

Electrical connection

1) Voltage (V) 220 - 240

Frequency (Hz) 50

Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)

Water supply

Cold water or hot water

2) max 60 °C

Capacity Place settings 9

Power consumption Left-on mode (W) 5.0

Power consumption Off-mode (W) 0.50

1) Refer to the rating plate for other values.

2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot

water supply to decrease energy consumption.

RATING PLATE

Mod. ... ... ...

Prod. No. ... ... ...

Ser. No. ...

INFORMATION FOR INDEPENDENT TEST

INSTITUTES OR ACCREDITED

LABORATORIES ONLY

For all the necessary information for test

performance, send an email to:

[email protected]

Write down the product number (PNC) that is on

the rating plate.

ENVIRONMENTAL CONCERNS

Recycle materials with the symbol . Put the

packaging in relevant containers to recycle it. Help

protect the environment and human health by

recycling waste of electrical and electronic

appliances. Do not dispose of appliances marked

with the symbol with the household waste.

Return the product to your local recycling facility or

contact your municipal office.

16

Page is loading ...

Zanussi ZDV14003FA User manual

Zanussi ZDV14003FA User manual

in other languages

Related papers