GE WASHERS User manual

Brand: GE

Model: WASHERS

Category: Washing machines

Type: User manual

ge.com
Owner’s Manual
Washers
175D1807P563 49-90295-1    09-06 JR
Safety Instructions . . . . . . . . . .2, 3
Operating Instructions
Care and Cleaning 
of the Washer  . . . . . . . . . . . . . . . . . . . . 9
Control Panels  . . . . . . . . . . . . . . . . . .4, 6
Control Settings   . . . . . . . . . . . . . . . .4–7
Features  . . . . . . . . . . . . . . . . . . . . . . . . . .8
Loading and Using 
the Washer  . . . . . . . . . . . . . . . . . . . . . . . 9
Troubleshooting Tips . . . . .10–12
Consumer Support
Consumer Support  . . . . . . . . . . . . . . .16
Warranty  . . . . . . . . . . . . . . . . . . . . . . . .15
Write the model and serial 
number here:
Model # ______________
Serial # ______________
You can find them 
under the lid of 
the washer.

■ Install or store where it will not be exposed to

temperatures below freezing or exposed to the

weather, which could cause permanent damage

and invalidate the warranty.

■ Properly ground washer to conform with all

governing codes and ordinances. Follow details

in Installation Instructions.

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk

of fire or explosion, electric shock, or to prevent property damage, personal injury,

or loss of life.

WATER HEATER SAFETY

Under certain conditions, hydrogen gas may be produced in a water heater that has not been

used for two weeks or more. Hydrogen gas can be explosive under these circumstances.

If the hot water has not been used for two weeks or more, prevent the possibility of damage or injury by

turning on all hot water faucets and allowing them to run for several minutes. Do this before using any

electrical appliance which is connected to the hot water system. This simple procedure will allow any

built-up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or

appliance during this process.

PROPER INSTALLATION

This washer must be properly installed and located in accordance with the Installation

Instructions before it is used. If you did not receive an Installation Instructions sheet, you can

receive one by visiting ge.com or by calling 800.GE.CARES (800.432.2737).

YOUR LAUNDRY AREA

■ Keep the area underneath and around your

appliances free of combustible materials such as

lint, paper, rags, chemicals, etc.

■ Close supervision is necessary if this appliance is

used by or near children. Do not allow children to

play on, with or inside this or any other appliance.

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Use this

appliance

only for its

intended

purpose as

described in

this Owner’s

Manual.

ge.com

WHEN USING THE WASHER

■ Never reach into washer while it is moving.

Wait until the machine has completely stopped

before opening the lid.

■ Do not mix chlorine bleach with ammonia or acids

such as vinegar and/or rust remover. Mixing

different chemicals can produce a

toxic gas which may cause death.

■ Do not wash or dry articles that have been

cleaned in, washed in, soaked in or spotted with

combustible or explosive substances (such as

wax, oil, paint, gasoline, degreasers, dry-cleaning

solvents, kerosene, etc.). These substances give off

vapors that may ignite or explode. Do not add

these substances to the wash water. Do not use or

place these substances around your washer or

dryer during operation.

■ The laundry process can reduce the flame

retardancy of fabrics. To avoid such a result,

carefully follow the garment manufacturer’s

wash and care instructions.

■ To minimize the possibility of electric shock,

unplug this appliance from the power supply

or disconnect the washer at the building’s

distribution panel by removing the fuse or

switching off the circuit breaker before attempting

any maintenance or cleaning.

NOTE: Turning the Cycle Selector Knob to an off

position, or pressing PAUSE does NOT disconnect

the appliance from the power supply.

■ Never attempt to operate this appliance if it is

damaged, malfunctioning, partially disassembled,

or has missing or broken parts, including a

damaged cord or plug.

WHEN NOT IN USE

■ Turn off water faucets to relieve pressure on hoses

and valves and to minimize leakage if a break or

rupture should occur. Check the condition of the fill

hoses; GE recommends changing the hoses every

5 years.

■ Before discarding a washer, or removing it

from service, remove the washer lid to prevent

children from hiding inside.

■ Do not attempt to repair or replace any part of this

appliance unless specifically recommended in this

Owner’s Manual, or in published user-repair

instructions that you understand and have the

skills to carry out.

■ Do not tamper with controls.

READ AND FOLLOW THIS SAFETY INFORMATION

CAREFULLY.

SAVE THESE INSTRUCTIONS

• Add detergent

• Add diluted fabric

softener (on models

with a fabric

softener dispenser)

• Add clothes

• Select load size and

other wash options

• Select wash cycle

• Close lid

• Pull knob

Quick Start Guide

About the control panel—for models with “pull knob” start.

Load Size

Loosely load clothes no higher than the top row of holes in the washer basket. The water level should just cover

the clothes. Adjust the load size accordingly.

Temperature (on some models)

Select the water temperature for the wash and rinse cycles. Always follow fabric manufacturer’s care label or

instructions when laundering.

Options (on some models)

2nd Rinse Option

When you use extra detergent or bleach to clean heavily soiled clothes, you may want to use the 2nd Rinse

option. It provides a second deep cold rinse.

Step 1

Step 2

Step 3

Step 4

Controls

ge.com

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Wash Cycle—Cycle Selector Knob

The chart below will help you match the wash cycle setting with your clothing. The chart is ranked from longest to

shortest cycle time and wash intensity.

Your washer may not have all these cycles. (Cycles vary by model.)

PREWASH For removing surface dirt from heavily soiled clothes. Make sure to follow with a

regular wash cycle.

CASUALS For wrinkle-free and permanent press items, and knits.

COTTONS For heavy to lightly soiled cottons, household linens, work and play clothes.

or WHITES

EASY CARE For wrinkle-free and permanent press items, and knits.

DELICATES For lingerie and special-care fabrics with light to normal soil.

HAND WASH For items labeled handwashable with light soils. Provides periods of agitation and soak

during wash and rinse.

SPEED WASH For lightly soiled items that are needed in a hurry.

SPIN For draining the tub and spinning water out of the clothes.

DARK COLORS For non-colorfast cottons and blends and items that are labeled cold wash by the fabric

manufacturer.

COLORS For wrinkle-free and permanent press items, knits and cottons.

RINSE SPIN For quickly rinsing chlorine, perspiration, stains, etc., out of clothes.

15 MIN/30 MIN For very soiled clothes. Begins with agitation, soaks for a specified period of time, then moves

AUTO SOAK through the rest of the cycle automatically.

2nd RINSE Provides an automatic, second deep rinse to thoroughly remove detergent or bleach from

your clothes.

• Add detergent

• Add diluted fabric

softener (on models

with a fabric

softener dispenser)

• Add clothes

• Select load size and

other wash options

• Select wash cycle

• Close lid

• Push START

Quick Start Guide

About the control panel—for models with START button.

Load Size

Loosely load clothes no higher than the top row of holes in the washer basket. The water level should just cover

the clothes. Adjust the load size accordingly.

Temperature

Select the water temperature for the wash and rinse cycles. Always follow fabric manufacturer’s care label or

instructions when laundering.

PerfecTemp senses the incoming water temperature and adjusts the fill water to obtain a more precise

temperature range for all wash temperatures. For example, in a COLD wash selection, some warm water

may be added to reach a temperature needed to better dissolve detergents. Often, detergents are not

completely dissolved in very cold water, especially in cooler climates.

During winter months, when the water entering your home is colder, or for locations with very cold water year

round, use the PerfecTemp plus COLD to help dissolve powdered detergents and to improve the cleaning of

your clothes.

The TAP COLD feature turns the PerfecTemp feature on your washer off, and uses your household tap water

temperature for a COLD wash. This can provide energy savings by reducing the amount of hot water used in

your wash.

Options

Autosoak Option (on some models)

This option begins with a brief agitation, soaks for a specified period of time, then moves through the rest of the

cycle automatically. On some models, this option is located on the Cycle Selector knob.

2nd Rinse Option (on some models)

When you use extra detergent or bleach to clean heavily soiled clothes, you may want to use the 2nd Rinse

option. It provides a second deep cold rinse.

Extended Spin Option (on some models)

Use this option to extract more water from your clothes. Clothes will be drier when this option is selected and will

dry more quickly in your dryer.

Step 1

Step 2

Step 3

Step 4

Controls

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

ge.com

Status Indicator Lights

The Cycle Indicator Lights show what stage the washer is in. When the Selector knob is set to a new cycle, the Indicator

Lights will flash momentarily, showing what stages the cycle will go through. On models without an AUTO SOAK option,

the SOAK light will not light up.

Wash Cycle—Cycle Selector Knob

The wash cycle controls the length and intensity of the washing process. The knob can be turned in either direction.

Turning the Cycle Selector knob after starting a cycle will stop the washer and reset the cycle to the new selection.

Press START to begin the new cycle selection.

The chart below will help you match the wash cycle setting with your clothing. The chart is ranked from longest to

shortest cycle time and wash intensity. (Cycles vary by model.)

PREWASH For removing surface dirt from heavily soiled clothes. Make sure to follow with a

regular wash cycle.

CASUALS For wrinkle-free and permanent press items, and knits.

COTTONS For heavy to lightly soiled cottons, household linens, work and play clothes.

EASY CARE For wrinkle-free and permanent press items, and knits.

DELICATES For lingerie and special-care fabrics with light to normal soil.

HAND WASH For items labeled handwashable with light soils. Provides periods of agitation and soak

during wash and rinse.

SPEED WASH For lightly soiled items that are needed in a hurry.

DRAIN & SPIN For draining the tub and spinning water out of the clothes.

SPIN ONLY

AUTO SOAK For very soiled clothes. Begins with a brief agitation, soaks for a specified period of time,

then moves through the rest of the cycle automatically.

START

Press START to begin the cycle. Pressing START again or raising the lid will PAUSE the cycle and the Cycle indicator light

will blink.

To continue the cycle, press START again or close the lid. If machine is paused more than 24 hours, the cycle will be

cancelled. To stop the cycle, hold the button for 3 seconds. If water remains in the machine, select the DRAIN & SPIN

OR SPIN ONLY cycle to drain tub and spin water out of the washer tub.

Raising the lid will stop agitation or spin action, but does not pause the cycle.

Separate for cleaning

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

About washer features.

Cleaning the Fabric Softener Dispenser (on some models)

Remove the dispenser from the top of the agitator.

Separate the dispenser cup from the cover by grasping the top and pushing down on the

inside of the cup with your fingers. Dispenser cup will pop free from the cover.

To clean the dispenser, soak both the dispenser cup and the dispenser cover in the

following solution:

■ 1 US gallon (3.8 liters) warm water

■ 1/4 cup (60 ml) heavy-duty liquid detergent

■ 1 cup (240 ml) bleach

If necessary, loosen buildup with a clean, soft cloth after soaking. Do not use a stiff brush;

you may roughen the surface of the dispenser.

Rinse and reassemble dispenser. Place dispenser back on the agitator.

The Agitator Cap or Fabric Softener Dispenser (depending on model)

The agitator cap fits into the top of the

agitator. If it accidentally comes off,

simply put it back on.

The fabric softener dispenser automatically

releases liquid fabric softener at the proper

time during the cycle.

Do not stop the washer during the first spin.

This will cause the dispenser to empty

too soon.

To use, follow these steps:

Make sure dispenser is securely attached

to agitator.

Use only liquid fabric softener.

Pour into dispenser, using amount

recommended on package.

Never pour fabric softener directly on

clothes. It may stain them.

Add water to dispenser until it reaches

the maximum fill line.

Do not pour anything into the

agitator if the agitator cap or

dispenser is removed.

Liquid Bleach Funnel

The water fill dilutes liquid chlorine bleach as the washer fills for the wash cycle.

Check clothing care labels for special instructions.

Measure liquid bleach carefully, following instructions on the bottle.

■ Never pour undiluted liquid chlorine bleach directly onto clothes or into the wash basket.

■ Do not pour powdered bleach into bleach funnel.

Before starting the washer, pour measured amount of bleach directly into bleach funnel.

Avoid splashing or over-filling dispenser. If you prefer to use powdered bleach, add it into

the wash basket with your detergent.

■ Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.

Mixing can produce a toxic gas which may cause death.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Loading and using the washer.

Always follow fabric manufacturer’s care label when laundering.

ge.com

Sorting Wash Loads

Sort by color (whites, lights, colors), soil level,

fabric type (sturdy cottons, easy care, delicates)

and whether the fabric produces lint (terry cloth,

chenille) or collects lint (velveteen, corduroy).

Proper Use of Detergent

Add detergent and start the washer before adding

clothes so that the detergent can work effectively.

Using too little or too much detergent is a common

cause of laundry problems.

You can use less detergent if you have soft water,

a smaller load or a lightly soiled load.

Loading the Washer

Load dry items loosely, no higher than the top row of

holes in the washer basket. When loading wet items,

make sure you set the load/water level high enough

to allow the items to move freely. Water level should

just cover the clothes. To add items after washer has

started, lift the lid and submerge additional items next

to the agitator.

■ Do not wrap long items like sheets or pants

around the agitator.

■ Do not wash fabrics containing flammable

materials (waxes, cleaning fluids, etc.).

■ Agitation will not start with the lid up.

Wash Basket: Leave the lid open after washing to

allow moisture to evaporate. If you want to clean

the basket, use a clean soft cloth dampened with

liquid detergent; then rinse. (Do not use harsh or

gritty cleaners.)

Fill Hoses: GE recommends changing the hoses

every 5 years.

Exterior: Immediately wipe off any spills. Wipe

with damp cloth. Try not to hit surface with

sharp objects.

Moving and Storage: Ask the service technician to

remove water from drain pump and hoses. See the

Installation Instructions packed with product for

information on how to reinstall the shipping rod

to keep the tub stationary when moving the washer.

For more information, visit ge.com or call

800.GE.CARES (800.432.2737). Do not store

the washer where it will be exposed to the weather.

Long Vacations: Be sure water supply is shut off at

faucets. Drain all water from hoses if weather will

be below freezing.

Care and cleaning of the washer.

WATER Possible Causes What To Do

Too many suds Too much detergent • Measure your detergent carefully. Use less soap if you have

soft water, a smaller load or a lightly soiled load.

Type of detergent • Switch to a lower sudsing detergent brand and follow

instructions on package.

Soft water • Try less detergent.

Water leaks Using too much detergent • Use less detergent. Use less soap if you have soft water,

in washer a smaller load or a lightly soiled load.

Fill hoses or drain hose is • Make sure hose connections are tight at faucets and

improperly connected rubber washers are installed. Make sure end of drain hose

is correctly inserted in and secured to drain facility.

Household drain may • Check household plumbing. You may need to call

be clogged a plumber.

Constant water pressure • Tighten hoses at the faucets and turn the water off after

to the fill hoses at the each use.

water source

• Check condition of the fill hoses; they should be replaced

every 5 years.

Water temperature Cooler water temperatures • New laundry detergents have been formulated to work

seems incorrect provide improved energy with cooler water temperatures without affecting wash

efficiency performance.

Water supply is turned off • Turn both hot and cold faucets fully on and make sure

or improperly connected hoses are connected to correct faucets.

Water valve screens are • Turn off the water source and remove the water connection

stopped up hoses from the upper back of the washer. Use a brush or

toothpick to clean the screens in the machine. Reconnect

the hoses and turn the water back on.

House water heater is • Make sure house water heater is delivering water at

not set properly 120°F–140°F (48°C–60°C).

Water pumped out before Lid lifted or cycle was put in • Reset cycle.

cycle is complete pause for over 24 hours

Water won’t drain Drain hose is kinked or • Straighten drain hose and make sure washer is not

improperly connected sitting on it.

• Top of drain outlet should be less than 8 ft (2.5 m)

above floor.

Washer pauses during The PREWASH Cycle or • This is normal. The washer alternates between agitate and

wash cycle AUTO SOAK Option was soak during these cycles to get your clothes cleaner with

chosen less wear.

Washer pauses during This is normal • The washer may pause during the spin cycle to remove

spin cycle soapy water more efficiently.

Troubleshooting Tips

Save time and money! Review the charts on the following pages,

or visit ge.com. You may not need to call for service.

Before you call for service…

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

OPERATION Possible Causes What To Do

Washer won’t operate Washer is unplugged • Make sure cord is plugged securely into a working outlet.

Water supply is turned off • Turn both hot and cold faucets fully on.

Controls are not set properly • Check controls.

Lid is open—safety feature • Close lid and reset cycle, to the beginning if necessary.

prevents agitation and

spinning when lid is up

Circuit breaker/fuse is • Check house circuit breakers/fuses. Replace fuses or

tripped/blown reset breaker. Washer should have separate outlet.

Electronics need to be reset • Unplug washer, wait 2 minutes, plug back in and press START.

START was not pressed • Press START.

Lid magnet missing • Call for service.

Time not shown Unit filling • This is normal. Estimated time remaining is updated during

on display fill time.

Movement inside machine Shifting mechanism is • When the machine is manually turned off, the shifter will

when shut off disengaging the motor disengage the motor before completely shutting down.

If lid is raised before the motor is disengaged, it will resume

when lid is closed.

PERFORMANCE Possible Causes What To Do

Clothes too wet Incorrect spin cycle • Make sure the spin cycle selected matches the load you are

selected washing. Some fabrics will feel wetter when rinsed with cold water.

Colored spots Incorrect use of fabric • Check fabric softener package for instructions and follow

softener directions for using dispenser.

• Pretreat stain and rewash.

Dye transfer • Sort whites or lightly colored items from dark colors.

Grayed or yellowed Not enough detergent • Use more detergent (especially with larger loads).

clothes Be sure to follow detergent manufacturer’s directions.

Hard water • Use a water conditioner like Calgon brand or install

a water softener.

Water is not hot enough • Make sure water heater is delivering water at

120°F–140°F (48°C–60°C).

Washer is overloaded • Select load size to match clothes load.

Detergent is not • Add detergent as wash basket fills with water before

dissolving you load clothes.

Dye transfer • Sort clothes by color. If fabric label states wash separately,

unstable dyes may be indicated.

Lint or residue on Clothes are air or line dried • If you do not dry your clothes with a clothes dryer, your

clothes clothes may retain more lint.

Incorrect sorting • Separate lint producers from lint collectors.

Washing too long • Wash small loads for a shorter time than larger loads.

Detergent not dissolving • Add detergent as wash basket fills with water, before you

load clothes.

• Try a liquid detergent.

• Use warmer water temperature.

Overloading • Load clothes no higher than the top row of holes in the

washer basket.

• Make sure load size selected matches clothes load size.

Incorrect use of fabric • Check fabric softener package for instructions

softener and follow directions for using dispenser.

ge.com

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

Before you call for service…

PERFORMANCE (cont.) Possible Causes What To Do

Pilling Result of normal wear on • While this is not caused by the washer, you can slow the

poly-cotton blends and pilling process by washing garments inside out.

fuzzy fabrics

Snags, holes, tears, rips Pins, snaps, hooks, sharp • Fasten snaps, hooks, buttons and zippers.

or excessive wear buttons, belt buckles,

• Remove loose items like pins, objects in pockets and

zippers and sharp objects

sharp buttons.

left in pockets

• Turn knits (which snag easily) inside out.

Undiluted chlorine bleach • Check bleach package instructions for proper amount.

• Never add undiluted bleach to wash or allow clothes to

come in contact with undiluted bleach.

Chemicals like hair bleach or • Rinse items that may have chemicals on them before

dye, permanent wave solution washing.

Wrinkling Improper sorting • Avoid mixing heavy items (like work clothes) with light items

(like blouses).

• Try a fabric softener.

Overloading or incorrect • Load your washer so clothes have enough room to move

water level freely with water covering all of the clothes.

Incorrect wash and • Match Cycle selection to the type of fabric you are washing

dry cycles (especially for easy care loads).

Repeated washing in • Wash in warm or cold water.

water that is too hot

SOUNDS Possible Causes What To Do

“Metallic clicking” Shifter mechanism is • The drive system will engage at the start of agitate and

engaging or disengaging disengage when agitate is complete. This occurs multiple

times during the wash.

Back and forth “swoosh” Electric motor reversing • This machine has a drive system that doesn’t use gears.

or light “clicking” sound direction This sound is the motor rotating back and forth to agitate

during agitate your laundry.

Quick short agitation Clothing redistribution • At the end of agitate, the motor makes short agitation strokes

sounds at end of agitate to redistribute the load.

“Click” when water Relay switch • The relay makes a click sound when activated. The water

stops filling level activates the relay and stops filling.

“Clicking” behind Control Automatic Temperature • This valve mixes in cold and hot water. The “clicking” is the

Panel during fill Control Valve valve turning on and off.

Water volume changes Automatic Temperature • This valve mixes in cold and hot water. The sound changes

during fill Control Valve when the valves are turned on and off.

Motor “whining up” or Motor ramping up/down • The motor will speed up incrementally during the spin cycle.

“coasting down” in spin during spin cycle When spin is complete, it will coast until it stops.

“Humming” Water drain pump • The drain pump will make a humming sound when pumping

out water after agitation stops and continue until spin is

complete.

“Gurgling” Water drain pump • When the pump starts drawing in air, It starts to gurgle.

The washer should then begin spinning and the sound will

continue until it is done spinning.

Troubleshooting Tips

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Notes.

ge.com

Operating Instructions Safety Instructions

Consumer Support

Troubleshooting Tips

Notes.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

For The Period Of: We Will Replace:

One Year Any part of the washer which fails due to a defect in materials or workmanship. During this

From the date of the limited one-year warranty, we will also provide, free of charge, all labor and related service to

original purchase replace the defective part.

What Is Not Covered:

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care

technician. To schedule service,

on-line, 24 hours a day, visit us at ge.com, or call 800.GE.CARES

(800.432.2737). Please have serial number and model number

available when calling for service.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the

USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a

trip charge or you may be required to bring the product to an Authorized GE Service location. In Alaska, the warranty excludes the

cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal

rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local

or state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

■ Service trips to your home to teach you how to use

the product.

■ Improper installation, delivery or maintenance.

■ Failure of the product if it is abused, misused, or

used for other than the intended purpose or used

commercially.

■ Replacement of house fuses or resetting of circuit

breakers.

■ Products which are not defective or broken, or which are

working as described in the Owner’s Manual.

■ Damage to the product caused by accident, fire, floods

or acts of God.

■ Incidental or consequential damage caused by possible

defects with this appliance.

■ Defects or damage due to operation in freezing

temperatures.

■ Damage caused after delivery.

■ Product not accessible to provide required service.

Staple your receipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

GE Washer Warranty.

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this Limited

Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular

purpose, are limited to one year or the shortest period allowed by law.

Printed in the United States

Consumer Support.

GE Appliances Website

ge.com

Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,

any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,

order parts or even schedule service on-line.

Schedule Service ge.com

Expert GE repair service is only one step away from your door. Get on-line and schedule your service at

your convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal business

hours.

Real Life Design Studio ge.com

GE supports the Universal Design concept—products, services and environments that can be used by

people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and

mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen design ideas

for people with disabilities, check out our Website today. For the hearing impaired, please call 800.TDD.GEAC

(800.833.4322).

Extended Warranties ge.com

Purchase a GE extended warranty and learn about special discounts that are available while your warranty

is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.

GE Consumer Home Services will still be there after your warranty expires.

Parts and Accessories ge.com

Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes

(VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or by phone

at 800.626.2002 during normal business hours.

Instructions contained in this manual cover procedures to be performed by any user. Other servicing

generally should be referred to qualified service personnel. Caution must be exercised, since improper

servicing may cause unsafe operation.

If you are not satisfied with the service you receive from GE, contact us on our Website with all the details

including your phone number, or write to: General Manager, Customer Relations

GE Appliances, Appliance Park

Louisville, KY 40225

enhanced communication and prompt service under the terms of your warranty, should the need arise.

You may also mail in the pre-printed registration card included in the packing material.

Page is loading ...

GE WASHERS User manual

Brand: GE

Model: WASHERS

Category: Washing machines

Type: User manual

Download PDF

report

in other languages

español: GE WASHERS Manual de usuario

GE WASHERS User manual

GE WASHERS User manual

in other languages

Related papers

Other documents