Aeg-Electrolux DM8600-M User manual

Benutzerinformation

Gebruiksaanwijzing

Notice d'utilisation

User manual

DD 8770 - HD 6470

Dunstabzugshaube

Afzuigkap

Hotte

Cooker Hood

DM 8700 - DM 8600 - DM 8400

Page is loading ...

62

Contents

Safety warnings 63

Description of the appliance 65

Extraction 65

Recirculation 65

Control Panel - Model DM 8700 - DD 8770 66

Switching on the hood 67

Switching on the light 67

Control device for grease or charcoal filter 67

Led signal for grease filter 67

Led signal for charcoal filter 67

Re-setting the saturation signal 67

Control Panel - Model DM 8600 68

Control device for grease and charcoal filters 69

Grease filter LED (D) 69

Charcoal filter LED (E) 69

Resetting the saturation indicator 69

Control Panel - Model DM 8400 - HD 6470 70

Maintenance and care 71

Cleaning the hood 71

Metal grease filter 71

Removing the metal grease filter 71

Charcoal filter 72

Changing the light bulb 73

Special accessories 73

What to do if 74

Technical assistance service 75

Technical specifications 76

Mounting accessories included 76

Electrical connection 77

Wall unit mounting 78

Special accessories/Vapour screen 83

63

Safety warnings

• When used as an extractor unit, the hood must be fitted with a hose

having preferably the same diameter as the outlet hole.

Should there already be a pipe of diameter 125 mm that ducts to the

outside through the walls or roof, it is possible to use the 150/125

mm reduction flange provided. In this case the hood will be slightly

noisier.

Attention: The hose is not supplied and must be purchased

separately.

• The minimum distance between the supporting surface for the

cooking vessels on the hob and the lowest part of the range hood

must be not less than 50cm from electric cookers and 65cm from

gas or mixed cookers.

If the instructions for installation for the gas hob specify a greater

distance, this must be adhered to.

• Before any cleaning or maintenance operation, disconnect the hood

from the mains by removing the plug or disconnecting the home

mains switch.

• The appliance is not intended for use by children or persons with

impaired physical, sensorial or mental faculties, or if lacking in

experience or know-how, unless they are under supervision or have

been trained in the use of the appliance by a person responsible for

their safety.

• Children should be monitored to ensure that they do not play with the

appliance.

• Never use the hood without effectively mounted grating.!

• The hood must NEVER be used as a support surface unless

specifically indicated.

• The premises must be sufficiently ventilated, when the kitchen hood

is used together with other gas combustion devices or other fuels.

• The suctioned air must not be conveyed into a conduit used for the

disposal of the fumes generated by appliances that combust gases

or other fuels.

• The flaming of foods beneath the hood itself is severely prohibited.

• The use of exposed flames is detrimental to the filters and may

cause a fire risk, and must therefore be avoided in all circumstances.

• Any frying must be done with care in order to make sure that the oil

does not overheat and burst into flames.

• As regards the technical and safety measures to be adopted for

fume discharging it is important to closely follow the relations

provided by the competent authorities.

64

• The hood must be regularly cleaned on both the inside and outside

(AT LEAST ONCE A MONTH, it is in any event necessary to proceed

in accordance with the maintenance instructions provided in this

manual)..

• Failure to follow the instructions as concerns hood and filter cleaning

will lead to the risk of fires.

• Do not use or leave the hood without the lamp correctly mounted

because of the possible risk of electric shocks.

• We decline any responsibility for any problems, damage or fires

caused to the appliance as the result of the non-observance of the

instructions included in this manual.

This appliance is marked according to the European directive 2002/96/

EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent

potential negative consequences for the environment and human health,

which could otherwise be caused by inappropriate waste handling of

this product.

The symbol on the product, or on the documents accompanying

the product, indicates that this appliance may not be treated as

household waste. Instead it shall be handed over to the applicable

collection point for the recycling of electrical and electronic equipment.

Disposal must be carried out in accordance with local environmental

regulations for waste disposal.

For more detailed information about treatment, recovery and recycling

of this product, please contact your local city office, your household

waste disposal service or the shop where you purchased the product.

65

Description of the Appliance

• The cooker hood is designed to extract unpleasant odours

from the kitchen, it will not extract steam.

• The hood is supplied as an extractor unit and can also be used with

a recirculation mode by fitting a charcoal filter.

• You will need an original charcoal filter for this function (Available

from your local Service Force Centre).

• Only for HD 6470: The cooker hood is supplied ready for use as a

recirculation hood and may be used for extraction by removing the

charcoal filter which has been fitted inside the

cooker hood.

Extraction mode

• In this mode fumes are extracted to the

outside via a hose connected to the coupling

ring A. Fig. 1.

• In order to obtain the best performance the

hose should have a diameter equal to the

outlet hole.

Should there already be a pipe of diameter 125

or 120 mm that ducts to the outside through

the walls, it is possible to use the 150/125-120

mm reduction flange provided. In this case the

hood will be slightly noisier.

Recirculation mode

• The air is filtered through a charcoal filter and

returned to the kitchen.

• You will need an original charcoal filter for the

recirculation mode. (See Special Accessories).

• Assemble the deflector (3 parts): the three

parts must be fixed with 2 screws Ø 3.5 13 mm,

the extension of the deflector is adjustable and

must correspond to the width of the chimney flue

support, to which it must be fixed.

Fix the deflector using 4 screws Ø 2,9x6.5 mm.

Fig. 2.

• Optionally, the position of the chimney elements

can be changed.

When using the hood in the recirculation mode

the chimney must be fixed at the top, with the

air outlet grill at the side.

Fig. 1

coupling ring

Fig. 2

=

66

Control Panel

Model DM 8700 - DD 8770

• Best results are obtained by using a low speed for normal conditions

and a high speed when odours are more concentrated.

Turn the hood on a few minutes before you start cooking.

The hood should be left on after cooking for about 15 minutes or until

all the odours have disappeared. The control switches are located

on the hood’s front panel:

• The hood operation may be controlled via the control ball or with the

remote control (the remote control is a special accessory and is

ordered separately).

Every status change (changing speed, switching on the lights, etc.)

is recognisable from the variation of light emitted by the control ball

and by an acoustic signal.

The control ball serves also as a light signal :

• No signal :

The hood is switched off.

• Static green light :

Hood is switched on at power level 1 (minimum).

• Static orange light :

Hood is switched on at power level 2 (medium).

• Static red light :

Hood is switched on at power level 3 (maximum).

• Flashing red light :

Hood is switched on at intensive power level (timed at 5 minutes)

• Flashing green light :

Indicates the grease filter saturation - clean the grease filter

• Flashing orange light :

Indicates the charcoal filter saturation - clean or replace the

charcoal filter.

Attention!

The control ball flashes orange to indicate the saturation of the

charcoal filter even if the hood is used in the extraction mode and no

charcoal filter is fitted.

In this case, perform the signal reset operation as follows: select the

intensive speed (the control ball lights up with a red flashing light),

press again and hold pressed for about 3 seconds until an audible

signal indicates the reset has taken place.

67

Hood Operation - Model DM 8700 - DD 8770

Switching on the hood - Fig. 3

The control ball is a balancer switch.

Pressing the control ball repeatedly towards the right switches on the

hood and you may select the extraction level desired, pressing once

again on the right the hood switches off.

Switching on the light - Fig. 3

Press the control ball towards the left :

once for subdued lighting,

once again for full lighting,

press again to switch off the light.

press towards the

right to switch on the

hood

press towards the left

to switch on the light.

Fig. 3

Grease and charcoal filter maintenance

indicator

The air duct, in this hood, is provided with a device that signals when

the filter requires cleaning or changing .

Led signal for grease filter

The LED signal flickers (flickering green light) when the grease filter

requires cleaning, occurs at about 40 operating hours.

Carefully note the device for grease filter maintenance!

Led signal for charcoal filter

The LED signal flickers (flickering orange light) when the grease filter

requires cleaning, occurs at about 160 operating hours.

Re-setting the saturation signal

After cleaning or replacing the filter, select the intensive speed (the

control ball lights up with a red flashing light), press again and hold

pressed for about 3 seconds until a ‘bip’ sound indicates the reset.

68

Control Panel

Model DM 8600

• Best results are obtained by using a low speed for normal conditions

and a high speed when odours are more concentrated.

Turn the hood on a few minutes before you start cooking.

The hood should be left on after cooking for about 15 minutes or until

all the odours have disappeared. The control switches are located

on the hood’s front panel:

A - Mains switch, OFF.

B - Start and choice of motor speed 1-2-3

C - Indicates speed 1 (LED).

D - Indicates speed 2 and saturation of the grease filter (LED)

E - Indicates speed 3 and saturation of the charcoal filter (LED)

(flashing LED)

F - Indicates Intensive speed (LED).

G - Intensive speed on/off. The Intensive speed runs for 5 minutes:

If the hood is on when the Intensive speed is activated, the hood

reverts to previous speed after 5 minutes.

If the hood is off when the Intensive speed is activated, the hood

will be turned off after 5 minutes.

To interrupt the Intensive speed, press button A or B.

H - Light OFF

I - Light ON

Should the hood or the controls fail to operate: disconnect the power

supply for at least 5 seconds, then turn the hood back on again.

ABCDEFGH I

69

Grease and charcoal filter maintenance

indicator

This hood is fitted with a device that indicates when it is necessary to

clean the grease filter or the charcoal filter (if the hood is used in the

recirculation version with a charcoal filter).

On delivery, the hood is not supplied with a charcoal filter, so the

saturation indicator will be disabled.

If the hood is to be used with a charcoal filter, the saturation

indicator light must be enabled as follows:

Press buttons B and G simultaneously and hold them for 3 seconds.

At first only the grease filter LED D will light up, but when the charcoal

filter LED E lights up the saturation indicator will be enabled.

To disable it: Press buttons B and G again simultaneously and hold

them for 3 seconds, until the charcoal filter LED goes out.

Grease filter LED (D)

LED D will start to flash when it is time to clean the grease filter.

Cleaning will be necessary after 40 working hours. Always comply with

the maintenance instructions for the grease filter.

Charcoal filter LED (E)

The charcoal filter LED E will start to flash when the charcoal filter

needs to be replaced.

This operation is necessary after approximately 160 working hours.

Resetting the saturation indicator

After cleaning or replacing the filters, press button A for 3 seconds until

the grease filter LED D or the charcoal filter LED E stops flashing.the

grease filter LED D or the charcoal filter LED E stops flashing.

70

Control Panel

Model DM 8400 - HD 6470

• Best results are obtained by using a low speed for normal conditions

and a high speed when odours are more concentrated.

Turn the hood on a few minutes before you start cooking.

The hood should be left on after cooking for about 15 minutes or until

all the odours have disappeared. The control switches are located

on the hood’s front panel:

a- Indicator lamp

b- Light ON/OFF switch

c- Motor OFF - Speed 1 push-button

d- Speed 2 push-button

e- Speed 3 push-button

71

Maintenance and Care

• The hood must always be disconnected from the electricity

supply before beginning any maintenance work.

Cleaning the hood

• Clean the outside of the hood using a damp cloth and a solution of

water and mild washing up liquid.

• Never use corrosive, abrasive or flammable cleaning products or

products containing bleach. .

• Never insert pointed objects in the motor’s protective grid.

• Only ever clean the switch panel and filter grill using a damp cloth

and mild washing up liquid.

• It is extremely important to clean the unit and change the filters at

the recommended intervals. Failure to do so will cause grease

deposits to build up that could constitute a fire hazard.

Metal grease filter

• The purpose of the grease filters is to

absorb grease particles which form

during cooking and it must always be

used, either in the external extraction

or internal re-circulation function.

Attention: the metal grease filters

must be removed and washed, either

by hand or in the dishwasher, every

four weeks.

Removing the metal grease filter

• Pull the handle downwards, then remove the filter. Fig. 4.

Hand washing

Soak grease filters for about one hour in hot water with a grease-

loosening cleaner, then rinse off thoroughly with hot water. Repeat

the process if necessary. Refit the grease filters when they are dry.

Dishwasher

Place grease filters in the dishwasher. Select most powerful washing

programme and highest temperature, at least 65°C. Repeat the

process. Refit the grease filters when they are dry.

When washing the metal grease filter in the dishwasher a slight

discolouration of the filter can occur, this does not have any impact

on its performance.

• Clean the inner housing using a hand hot solution only(never use

caustic detergents, abrasive powders or brushes).

Fig. 4

72

i

g

h

g

Charcoal filter

• The charcoal filter should only be used if you want to use the hood in

recirculation mode.

• To do this you will need an original charcoal filter (available from your

local Service Force Centre).

• Cleaning/replacing the charcoal filter

Unlike other charcoal filters, the LONGLIFE charcoal filter can be

cleaned and reactivated. With normal use the filter should be cleaned

every second month (when using the hood 2,5 hours per day,on

average). The best way to clean the filter is in the dishwasher. Use

normal detergent and choose the highest temperature (65º C). Wash

the filter separately so that no food particles stick to the filter and

later causes bad odours. To reactivate the charcoal, the filter should

be dried in an oven for 10 minutes with a maximum temperature of

100º C.

After approximately three years of use, the charcoal filter should be

replaced with a new, as the odour reduction capacity will be reduced.

• Fitting

Remove the frame i which supports the filter h by turning 90° the two

knobs g.

Insert the charcoal filter inside the frame and put all parts back in

their place. Fig. 5.

• To remove proceed in the reverse order.

• Always specify the hood model code number and serial number

when ordering replacement filters. This information is shown on the

rating plate located on the inside of the unit.

• The charcoal filter can be ordered from your local Service Force

Centre.

Fig. 5

73

Fig. 6

Warning

• Failure to observe the instructions on cleaning the unit and changing

the filters will cause a fire hazard. You are therefore strongly

recommended to follow these instructions.

• The manufacturer declines all responsibility for any damage to the

motor or any fire damage linked to inappropriate maintenance or

failure to observe the above safety recommendations.

Changing the light bulb

• Disconnect the cooker hood from the mains supply.

• Remove the lamp cover carefully, use a screw driver as a

lever. Fig. 6.

• Replace the old bulb with a new one of the same type.

• Refit the lamp cover.

• If the light does not come on, make sure the bulb has been inserted

in correctly before contacting your local Service Force Centre.

Special accessories

Vapour screen see page 83

Remote control RM 8700 (only for model DM 8700 - DD 8770)

Charcoal filter Type 20

74

What to do if

If your appliance fails to work properly please carry out the following

checks.

Symptom Solution

The cooker hood will not start... Check that:

The hood is connected to

the electricity supply.

Check that a fan speed has

been selected

The cooker hood is not working Check that:

effectively.. The fan speed is set high

enough for the task.

The grease filters are clean.

The kitchen is adequately vented

to allow the entry of fresh air.

If set up for recirculation, check

that the charcoal filter is still

effective.

If set up for extraction, check that

the ducting and outlets are not

blocked.

The cooker hood has The safety cut-out device has been

switched off during operation... tripped.

Turn off the hob and then wait for

the device to reset.

If the hood has been installed

below the heights indicated in the

installation instructions the motor

will cut-out frequently which will

damage the hood.

If after all these checks, the problem persists, contact your local

Service Force Centre, quoting the model and serial number.

Please note that it will be necessary to provide proof of purchase for

any in-guarantee service calls.

In-guarantee customers should ensure that the above checks have

been made as the engineer will make a charge if the fault is not a

mechanical or electrical breakdown.

75

Technical assistance service (not for UK)

You are welcome to telephone our technical assistance service (see list of technical

assistance centres) whenever you need information or in the unlikely event of a fault.

For service in Australia call 1300 650 020.

When calling, please be ready to specify:

1. The model code number

2. The serial number (E-Nr.)

3. The manufacturing number (F-Nr.)

This information is shown on the registration plate inside the unit behind the

grease filter.

We reserve the right to change specifications and colours as a result of our policy of

continuing technological development.

Service and Spare Parts

In the event of your appliance requiring service, or if you wish to purchase spare parts,

contact your local Service Force Centre by telephoning: 08705 929 929

Your call will be automatically routed to the Service Centre covering your post code

area. For the address of your local Service Force Centre and further information about

Service Force, please visit the website at www.serviceforce.co.uk

Please ensure that you have read the section “What to do if...” as the engineer will make

a charge if the fault is not a mechanical or electrical breakdown even the appliance is

under warranty. Please note that proof of purchase is required for in-guarantee

service calls.

Help us to help you

Please determine your type of enquiry before writing or telephoning.

When you contact us we need to know:

• Your name • Clear and concise details of the fault

• Address and post code • Name and model of the appliance*

• Telephone number • E number*

• Serial number*

* This information can be found on the rating plate, which can be seen when the grease

filters are removed.

If you require Customer Service in the Republic of Ireland please contact us at

the address below:

AEG

Electrolux Group (Ire) Ltd

Long Mile Road

Dublin 12

Republic of Ireland

Tel: + 353 (0) 1 4090751

Email: [email protected]

76

Technical Specifications

Models DM 8600 DM 8700 DM 8400

HD 6470 DD 8770

Dimensions* - extractor version (in cm):

Height 66-112 70-113 66-112

Dimensions* - filter version (in cm):

Height 75,5-122 78-122 75,5-122

Maximum

absorbed power: 210 W 210 W 210 W

Motor absorption: 1 x 170 W 1 x 170 W 1 x 160 W

Lighting: 2 x 20W 2 x 20W 2 x 20W

Lenght of the cable: 150 cm 150 cm 150cm

Electrical connection: 220-240 V 220-240 V 230 V

Fuse rating:

5A Time Delay Fuse

* Width and depth depend on the glass body which is installed with the cooker hood,

see page 83

Mounting accessories included

1 deflector (3 pieces to assemble)

2 metal screws 3,5 x 13 (to assemble the deflector)

1 chimney support (3 pieces to assemble)

4 metal screws 4 x 8 (to assemble the chimney support)

4 metal screws 3,5 x 9,5 (to affix the deflector to the support)

2 metal screws 3 x 9 (Only for DD 8770 and HD 6470)

1 reduction flange Ø 125-120 mm

1 support bracket

5 wood-screws 5 x 45 mm (For brick or solid block installations only)

5 wall plugs Ø 8 mm (For brick or solid block installations only )

4 metal screws 2,9 x 6,5 (for chimney flue mounting)

4 metal screws 4 x 20 (to affix the screen to the cooker hood)

1 allen spanner (for TORX screws)

1 Vapour screen (Only for DD 8770 and HD 6470)

CUSTOMER CARE DEPARTMENT

For general enquiries concerning your AEG appliance or for further information on AEG

products, please contact our Customer Care Department by letter or telephone at the

address below or visit our website at www.aeg.co.uk

Customer Services Department

Major Appliances

AEGElectrolux

Addington Way

Luton

Bedfordshire

LU4 9QQ

08705 350 350 (*)

* calls to this number may be recorded for training purposes

77

Electrical connection

Safety warnings for the electrician

The mains power supply must correspond to the rating indicated on the

plate situated inside the hood. If provided with a plug connect the hood

to a socket in compliance with current regulations and positioned in an

accessible area. If it not fitted with a plug (direct mains connection) or if

the plug is not located in an accessible area apply a bi-polar switch in

accordance with standards which assures the complete disconnection

of the mains under conditions relating to over-current category III, in

accordance with installation instructions.

IMPORTANT: Before re-connecting the hood circuit to the mains supply

and checking the efficient function, always check that the mains cable

is correctly assembled.

78

Wall unit mounting - Fig. 7

First decide which functioning mode is better for you.

If you decide to use the hood in extraction mode we suggest you position

the upper section of the chimney so that the oulet slots are not visible

once installation is completed, however if is decided to use the hood in

rrecirculation mode BE SURE that the side with slots is up (see also A-B-

C sequence on on Fig. 7).

Assembling the chimney flue support/bracket (3 parts):

The three parts should be fixed with 4 screws, the support extension

is adjustable and should correspond to the internal width of the

telescopic chimney flue.

Assembling the deflector (3 parts – only for filter version):

The three parts should be fixed with 2 screws, the deflector

extension is adjustable and should correspond to the width of the

chimney flue support, to which it is then fixed.

A

B

180°

C - OK!

=

X

H

=

X

F

G

Fig. 7

79

• Only for DD 8770 and HD 6470:

Assemble the frame to the motor group (a - Fig. 8.1).

Connect lamps and control panel to the motor housing (b - Fig. 8.1).

Fix the frame to the motor group using 2 screws (c - Fig. 8.1).

• Mark the wall with a centre line, this will aid mounting procedure (1),

position the template so that the mid line printed on the template

matches with the centre line previously signed, the lower side of the

template corresponds to the lower side of the hood once mounted

(2).

• Drill two holes Ø 8mm and fix the support bracket with two wall plugs

and screws (3).

• Hang the hood (4) adjust its position (5-6) and from the inside of the

hood mark one point for definitive fixing (7), remove the hood and drill

a hole Ø 8mm (8), fit a wall plugs, hang the hood again and fix it

definitively with a screw (9).

• Drill two holes Ø 8mm on the upper side close to the ceilling (10), fit

two wall plugs and fix the chimney support with two screws (11).

In case the hood is to be used in filter version, mount the deflector

F on the chimney support with four screws 2,9x6,5 and fit a vent

hose (12 - Not supplied - must be purchased) to connect deflector

to the outlet hole D of the hood.

In case the hood is to be used in extraction mode, then the deflector

must not be mounted and fit a vent hose (12 - Not supplied - must

be purchased) to connect outlet hole D of the hood to the outside.

• Make electrical connection (13), but leave the hood disconnected

from the main circuit board.

• Insert the vapour screen on the motor housing and fix it with four

screws M4x35 (14).

• Fix the chimney first up (15a) to the chimney support (15b), then on

the bottom (16a) to the upper side of the frame (16b) using four

screws 2,9x6,5.

• Connect the hood the the main circuit board and check if the hood

works properly.

Wall unit mounting - Fig. 8

Page is loading ...

83

Sonderzubehör/Wrasenschirm

Extra leverbare accessoires/Dampscherm

Accessoires/Séparateur de vapeur

Special accessories/Vapour screen

SM 8090

E-Nr. 942 121 998

SM 8091

E-Nr. 942 121 999

SM 8092

E-Nr. 942 122 000

SM 8093

E-Nr. 942 122 001

SM 8010

E-Nr. 942 122 006

89,9

50

89,8

50

105-85

50.3

50

60

88

50

89.8

89.9

50

70-80 (SM 8065 + BM 8005)

108-90 (SM 8085 + BM 8005)

BM 8005

E-Nr. 942 122 009

(NOT AVAILABLE FOR THE UK)

(NON DISPONIBLE POR UK)

SM 8085 (88cm) - E-Nr. 942 122 007

SM 8065 (60 cm) - E-Nr. 942 122 008

Page is loading ...

Aeg-Electrolux DM8600-M User manual

Aeg-Electrolux DM8600-M User manual

in other languages

Related papers

Other documents