GE ACS15D User and Care
- Category
- Split-system air conditioners
- Type
- User and Care
This manual is also suitable for
RoomAk
CondYioner
Contents
Adapter Plug
3
Model and Serial Numbers
2
Air Direction
5
Problem Solver
7
Appliance Registration
2
Repair Service
7
Care and Cleaning
6
Safety Instructions
2
Air Filter
6
User Maintenance Instructions 6
Condenser Coils
6
Warrantv
Back Cover
Grilles & Cabinet
6
Control Settings 4
Electrical Requirements
3
Energy-Saving Tips
2
Extension Cords
3
GEAmwer
Center
m
Grounding
3
80~6262000
Models ACD09L ACD21D
ACD14A ACS15D
ACD15D ACS18D
ACD18D ACS24D
GEAppiances
Help us
help you...
Before using your air
conditioner, read this book
carefully.
It is intended to help you operate
and maintain your new air
conditioner properly.
Keep it handy for answers to your
questions.
If you don’t understand something
or need more help, write (include
your phone number):
Consumer Affairs
GE Appliances
Appliance Park
Louisville, KY 40225
Write down the model
and serial numbers.
You’ll find them on a label behind
the front grille on the left side wall
of the air discharge duct, visible
through the louvers.
These numbers are also on the
Consumer Product Ownership
Registration Card that came with
your air conditioner. Before sending
in this card, please write these
numbers here:
Model Number
Serial Number
Use these numbers in any
correspondence or service calls
concerning your air conditioner.
If you received a damaged
air conditioner . . .
Immediately contact the dealer
(or builder) that sold it to you.
Save time and money.
Before you request
service . . .
Importint Safety
Instructions
Read all instructions before
Wing
this appliance.
When using this appliance, always
exercise basic safety precautions,
including the following:
● Use this appliance only for
ik
intended purpose
as described in
this Use and Care Book.
● This air conditioner must be
properly installed in accordance
with the Installation Instructions
before it is used. See
grounding
instructions on page 3.
●
Never unplug your
air
conditioner
by pulling on the power cord.
Always grip plug firmly and pull
straight out from the receptacle.
● Repair or replace immediately
all eleetric service cords that
have
beeome frayed or otherwise
damaged. Do not use a cord that
shows cracks or abrasion damage
along its length or at either the
plug or connector end.
SAVE
T~E
INSTRUCTIONS
Check the Problem Solver on
page 7. It lists causes of minor
operating problems that you can
correct yourself.
2
Energy-saving tips
● Keep the air filter clean. (See
instructions on page 6.)
●
For most efficient cooling, keep
the vent control in the closed
position except when you want to
allow a small amount of outdoor air
to enter the room or to exhaust air,
smoke or odors from the room.
●
Don’t let the room get too
hot. Whenever possible, turn the
unit on before the room heats up.
When heat is “stored up” in walls,
furniture, rugs and draperies, your
air conditioner takes longer to
produce the desired comfort
condition.
●
Keep windows and doors
closed. Cool, dry air escapes
when they’re open.
● Keep furnace floor registers and
cold air returns closed. Cold air
can easily escape through them.
●
Don’t let drapes or furniture block
the front of the unit and restrict air
flow when it is operating.
●
It’s best to operate your air
conditioner at high speed during
extremely hot weather.
●
Keep the outdoor condenser coil
clean. (See page 7.)
● Turn the air conditioner off
before vacations or extended
absences from home.
.—
Electrical
SafetY—IMPORTANT...
pleaSe
Read Carefully.
How to connect
230/208-volt perpendicular,
electricity
tandem or large tandem type wall
outlet. These
tv~es
of outlets are
For personal safety,
this appliance must be
properly grounded.
Electrical requirements
U5-volt
models require a
115/120-
volt a.c., 60
hz
grounded outlet
protected with a 15 amp time delay
fuse or circuit breaker.
The power cord on these
models
has
a three-prong (grounding) plug that
mates with a standard three-prong
(grounding) wall outlet (Fig. 1) to
minimize the possibility of electric
shock hazard from these appliances.
PREFERRED
METHOD
T
p–.:
~
‘
.
n
‘>
Q
\
h
%
r
\
f
..,Y
Y
INSURE PROPER
GROUNO
EXISTS
Fig. 1 ‘
BEFORE USE
Where a standard two-prong wall
outlet is encountered, it is your
.
.
available at most hardware stores.
m~
230/208-VOLT
MATCHING
PERPENDICULAR TYPE WALL OUTLET
LINE CORD PLUG
REQUIRES 20 AMP TIME DELAY FUSE
OR CIRCUIT BREAKER
PROTE~lON
@@
230/208-VOLT
MATCHING
TANOEM
TYPE
WALL OUTLET
LINE CORD PLUG
REQUIRES 15 AMP TIME DELAY FUSE
OR CIRCUIT BREAKER PROTECTION
60
,.
-e
@
mm
(.
\,
●
230/208-VOLT
MATCHING
LARGE TANDEM TYPE WALL OUTLET
LINE
CORO
PLUG
REQUIRES 30 AMP TIME DELAY FUSE
OR CIRCUIT BREAKER PROTECTION
TEMPORARY METHOD
I
PERMITTEOINCANADA)
=
(ADAPTER PLUGS NOT
P
ON
Fig. 2
BEFORE USE
The
larger
slot in the
adaDter
must be
aligned-with the larger
sl~t
in the wall
outlet to provide proper polarity in
the connection of the power cord.
CAUTION: Attaching the adapter
ground terminal to
wall
outlet cover
screw does not ground the appliance
unless
cover screw is metal, and not
insulated, and wall outlet is grounded
through house wiring. You should
have the circuit checked by a
qudifid
electrician to make sure the outlet
is properly grounded.
When disconnecting the power cord
from the adapter,
always hold the
adapter with one hand. If this is not
done, the adapter ground terminal is
very likely to break with
repeati
use.
Should the adapter ground
terminal break, DO
N~
USE the
appliance until a proper ground
has again been established.
personal responsibility and
~bligation
to have it replaced with a properly
Whether your air conditioner is a
grounded three-prong wall outlet.
115-volt or a 230/208-volt unit, it
Use of
etiension
cords
is
importint
to have the
wall
DO
N~,
UNDER ANY
CIRCUMSTANCES, CUT
OR
REMOm
THE THIRD
(GROUND) PRONG
~OM
THE POWER CORD.
230/208-volt
models
require their
own single branch circuit supplying
230/208-volt a.c., protected with a
time
delay
fuse or circuit breaker.
This is recommended for best
performance and to prevent
overloading house wiring circuits,
which could cause a possible fire
hazard from overheating wires.
~he
power cord on these models
has a 230/208-volt perpendicular,
tandem or large tandem type plug
that mates respectively with a
outlet and circuit checked by a
qualified electrician if there is
any doubt as to whether a proper
ground
exisk.
Use of adapter plug
(U5-volt
modek
only)
Because of potential safety hazards
under certain conditions, we
strongly recommend against use
of an adapter plug.
However,
if you still elect to use an adapter,
where local codes permit, a
TEMPORARY
CONNE~ION
may be made to a properly grounded
two-prong
wall
outlet by use of a
UL listed adapter (Fig. 2) available
at most local hardware stores.
Because of potential safety
hazards under certain conditions,
we
strongly recommend against the
use of an extension cord.
However,
if you
still
elect
to use an extension
cord, it is absolutely necessary that
it be a
UL listed 3-wire grounding
type appliance extension cord and
that the current carrying rating of
the cord in amperes be equal to or
greater than the branch circuit size
shown on the rating nameplate of
the appliance.
3
Opemting
Your Air Conditioner
Controk
SELECTOR
Selector Switch
OFF
turns air conditioner off.
*LOW FAN permits low fan speed
operation without cooling.
*MED FAN permits medium fan
speed operation without cooling.
*HIGH
FAN permits high fan
speed operation without cooling.
*For fan only operation,
Energy Saver Switch must be in
NORMposition.
LOW COOL
permits cooling with
low fan speed operation.
MED COOL permits cooling with
medium fan speed operation.
HIGH COOL permits cooling
with high fan speed operation.
1
10
THERMOSTAT
HOUR
TIMER
Thermostat Control
When you turn the Thermostat
Control to the desired setting, the
Timer Control
(on
models so equipped)
When
vou
turn the Timer Control
thermostat will automatically-control
.
to the MANUAL
setting.
the air
the temperature of the indoor air.
The higher the number selected,
the cooler the indoor air will be.
*Ene~y
Saver
Swikh
NORM
ENERGY
SAVER
SAVE
D
I
i
conditioner starts immediately and
operates continuously if the
Selector Switch is at any setting
other than OFF.
When used with the Delay
Start/Stop Switch, the Timer
Control turns the air conditioner
on or off at preset times.
To
delay the
stirt
of the air
conditioner anywhere from
1 to
~
hours:
1.
Set the Timer Control for the
number of hours you want to delay
the start of the air conditioning
The Energy Saver Switch controls
the fan operation. When it’s in the
NORM position, the fan will
circulate room air continuously.
When it’s in the SAVE position, the
fan will automatically cycle on and
the desired setting.
operation.
2. Set the Delay
Start/Stop Switch
at DELAY START.
3. Turn the
Selector Switch to
~
DELAY
START
TIMER
9
DELAY
m
STOP
off with the compressor.
To stop the air conditioning
operation from 1 to
~
hours later:
1.
Set the Timer Control for the
number of hours you want the air
conditioner to operate before
shutting off automatically.
2. Set the Delay Stirt/Stop Switch
at DELAY
S~P.
3.
Turn the Selector Switch to the
desired setting.
4
AIR IN AIR OUT
VENTILATION
Ventilation Control
When the AIR IN and AIR OUT
buttons are in the out position, the
vent door is closed and only the air
inside the room can be circulated
and conditioned.
Push the AIR IN button and it will
stay in, and the vent door will open
to allow a small amount of outdoor
air to enter the room. Push the AIR
IN
button again and it
will
return to
the out
posi~ion
and the vent door
will close.
Push the AIR OUT button and it
will stay in, and the vent door will
open
to allow air, smoke and odors
Ie
exhausted from the room.
hush the AIR OUT button again
and it will return to the out position
and the vent door will close.
For normal cooling
1. Set the Selector Switch at HIGH
COOL.
2. Set the Thermostat Control at
the desired number (usually 5-7 is a
good starting position). If room
temperature is not satisfactory after a
reasonable time, set the Thermostat
Control at a higher number for a
cooler room or at a lower number
for a warmer room.
3.
Set the Energy Saver Switch at
NORM position for continuous fan
operation or at SAVE position to
automatically cycle the fan on and
off with the compressor.
4.
Be sure the AIR IN and AIR
OUT buttons are in the out position
except for brief periods when you
t
to bring outdoor air into the
ruum
or exhaust room air to the
outside.
For maximum cooling
1.
Set the Selector Switch at HIGH
COOL.
2. Turn the Thermostat Control
to
10.
3. Be sure the AIR IN and AIR
OUT buttons are in the out
position.
4. Set the Energy Saver Switch at
the NORM position.
For quieter operation
1.
Set the Selector Switch at LOW
COOL position.
2. Turn the Thermostat Control to
the desired number.
When the Thermostat Control is set
on 9 or 10 and the Fan is set on low
speed, moisture may freeze on the
coils and prevent the unit from
cooling. If this happens, set the Fan
at high
speed
and set the Thermostat
Control to a lower number.
3. Be sure the AIR IN and AIR
OUT buttons are in the out position
4.
Set the Energy Saver Switch at
the NORM position.
Note: When the Energy Saver
Switch is at the SAVE position,
changes in the sound level may be
more noticeable than when it’s at
the NORM position.
For nighttime operation
During the cooler evening hours,
we recommend that you set the
Selector Switch at LOW COOL for
very quiet operation and the
Thermostat Control at mid-range
(5 or 6). Be sure the AIR IN and
AIR OUT buttons are in the out
position, and set the Energy Saver
Switch at NORM or SAVE position.
For extreme temperatures
For greatest economy and best
performance, we suggest that you
set the Selector Switch at HIGH
COOL in extremely hot weather.
To adjust air direction
Up and down
The up-and-down air direction
louvers
are controlled by fingertip
pressure on the louvers. They
regulate air discharge upward,
downward or straight out.
Side to side
ON
CIRCULAIRE
OFF
D
I
m
For fixed side-to-side air
direction,
set the Circulaire Switch
to ON until the desired air direction
is obtained, then move it to OFF.
For continuous side-to-side air
circulation, set the Circulaire
Switch to ON and leave it there.
5
Care and
Cleani~
USER
=TEN~CE
~STRUCTIONS
Turn air conditioner off and
remove the plug from the wall
outlet before cleaning.
Grille
& Cabinet
Wipe
both sides of grille with a
clean cloth lightly dampened with
mild liquid
dishwashing detergent,
or clean with a vacuum cleaner
brush. Be careful not to force the
movable louvers out of position.
Other areas behind the grille may
be wiped or vacuumed, taking care
not to damage the coil fins.
Wash cabinet with mild soap or
detergent and lukewarm water.
Never use strong chemicals,
solvenk or bleaching agenfi.
Condemer
Coik
These coils on the weather side
of the unit should be checked
periodically and cleaned if clogged
with dirt or soot from the atmosphere.
If extremely soiled, they may need
to
bes~
cleaned, a service
atiable
through your GE service outlet.
Air
Hlter
The air filter behind the front grille
should be checked and cleaned at
least every 30 days or as often as it
needs cleaning.
To remove the filter:
Air Inlet Grille Removal
If your air conditioner is mounted
flush inside the room or if the
window sill extends farther into the
room than the chassis, it maybe
necessary to remove the air inlet
grille before the filter can be
removed.
To remove the grille,
pull the air
inlet grille out by grasping the front
at one side and pushing down on
the top to disengage the tab. Do the
—
same to the other side.
The air filter can now be removed
from the grille—grasp the tab on
the filter and pull.
Grasp the tab at the bottom of the
unit and pull downward.
After cleaning, replace the air filter
and air inlet grille, pushing the
Clean the filter
with a vacuum
grille into place.
-
cleaner to remove light dust. Wash
the filter in lukewarm, soapy water
and rinse in clear water to remove
sticky dust.
When replacing the filter, be sure
the word FRONT is facing you as
you slide the filter back into place.
6
——-.
~
Questio~?
~
UseThis Problem Solver
PROBLEM
POSSIBLE CAUSE AND REMEDY
AIR CONDITIONER
●
Not plugged in. Plug may have been bumped loose by vacuum cleaner or furniture.
DOES
N~
OPERATE
.
If plugged
in,
fuse
could have blown or circuit breaker may have tripped.
AIR CONDITIONER
●
Curtains, blinds or furniture blocking front of air conditioner will restrict airflow.
“DOES
N~
COOL
AS IT SHOULD”
●
Thermostat Control may not be set high enough. Turn control to a higher number.
Highest setting should provide maximum cooling. When Energy Saver Switch is set
at SAVE, temperature range in room will vary more.
c
Air filter dirty, should be cleaned at least every
30
days. See instructions on page 6.
●
Room may have been very hot when air conditioner was first turned on. Allow time
for it to cool down.
●
Cold air maybe escaping through open furnace floor registers and cold air returns.
●
AIR IN or AIR OUT button maybe in the in position, allowing hot outside air to
enter the room or cool inside air to leave the room through the open vent door.
●
Cooling coils have iced up. To melt ice, set the Selector Switch to LOW FAN and
the Thermostat Control to a lower number.
OPERATING
●
Thermostat click, a metallic sound, maybe heard when compressor cycles on and
SOUNDS
off. This is normal.
●
Fan runs continuously when Selector Switch is in Cool or Fan position. This is
normal. When Energy Saver Switch is set at SAVE, fan cycles on and off with
compressor.
WATER DRIPPING
●
Excess water may overflow in extremely hot and humid weather. This is normal.
OUTSIDE
WATER DRIPPING
●
Air conditioner must be installed level or tilted slightly to the outside for proper
INSIDE
water disposal.
WATER IN BASE PAN
. This is normal for a short period in areas with little humidity; normal for a longer
(ON OUTDOOR SIDE)
period in very humid areas. Moisture removed from indoor air drains to rear of
cabinet where it is picked
up by a fan and thrown against the outdoor condenser coil.
If you need more help.. call, toll free:
GE Answer Center”
800.626.2000
consumer information service
If You Need Service
To obtain service, see your warranty
on the back page of this book.
We’re proud of our service and
want you to be pleased. If for some
reason you are not happy with the
s--vice
you
receive, here
are three
s
to
follow for further help.
FIRST, contact the people who
serviced your appliance. Explain
why you are not pleased. In most
FINALLY, if your problem is still
cases, this will solve the problem.
not resolved, write:
NEXT, if you are still not pleased,
Major Appliance
write all the details-including
Consumer Action Panel
your phone number—to:
20 North
Wacker
Drive
Manager, Consumer Relations
Chicago, Illinois 60606
GE Appliances
Appliance Park
Louisville, Kentucky 40225
7
YOUR GENERAL ELECTRIC ROOM AIR CONDITIONER
WARRANTY
Save proof of original purchase date such as your sales slip or
cancelled
check to establish warranty period.
WHAT IS COVERED
FULL ONE-YEAR WARRANTY
For one year from date of original
purchase, we will provide, free
of charge, parts and service labor
in your home to
repair
or replace
any
part
of
the
room
air
conditioner that
fails
because
of a manufacturing defect.
FULL FIVE-YEAR WARRANTY
For five years from the date of
original purchase, we will provide,
free of charge, parts and service
labor in your home to repair or
replace
any
part of
the
sea/ed
refrigemting
system
(the
compresso~
condenser, evaporator and all
connecting tubing) that fails
because of a manufacturing
defect.
For each of the above warranties:
Transportation expense to and
from a service shop and shop
service labor if required will be
free of charge.
This warranty is extended to
the original purchaser and any
succeeding owner for products
purchased for use in the 48 mainland
states, Hawaii and Washington,
D.C.
In Alaska the warranty is the same
except that it is LIMITED because you
must pay to ship the product to the
service shop or for the service
technician’s travel costs to your home.
All warranty service will be provided
by our Factory Service Centers or
by our authorized Customer Care”
servicers during normal working
hours.
Look in the White or Yellow Pages
of your telephone directory for
GENERAL ELECTRIC COMPANY,
GENERAL ELECTRIC FACTORY
SERVICE, GENERAL
ELECTRIC-
HOTPOINT
FACTORY SERVICE or
GENERAL ELECTRIC CUSTOMER
CARE
@
SERVICE.
WHAT IS NOT COVERED
●
Service trips to teach you how to
● Improper installation.
● Failure of the product resulting from
use the product.
If you have an installation
modifications to the product or due to
Read your Use and Care material.
problem, or if the air conditioner
unreasonable use including failure to
If you then have any questions
is of improper cooling capacity
provide reasonable and necessary
about operating the product,
for the intended use, contact
maintenance.
please contact your dealer or our
your dealer or installer. You are
Consumer Affairs office at the
c Failure due to corrosion on models
responsible for providing adequate
address below, or call, toll free:
electrical connecting facilities.
not corrosion-protected.
GE Answer
Center@
. Damage to the product caused
800.626.2000
● Replacement of fuses or
consumer information service
resetting of circuit breakers.
by improper power supply voltage,
accident, fire, floods or acts of God.
. In commercial locations labor
necessary to move the unit to a
WARRANTOR IS
NOT
RESPONSIBLE
location where it is accessible for
FOR CONSEQUENTIAL DAMAGES.
service by an individual technician.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
To know what your legal rights are in your state, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company
If further help is needed concerning this warranty, write:
Manager—Consumer Affairs, GE Appliances, Louisville, KY 40225
ACD09L
ACD21C
ACD14A
ACS15D
Pub.
No.
49-7199
ACD15D
ACS18D
1
I
10-88
ACD18D
ACS24E
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
GE ACS15D User and Care
- Category
- Split-system air conditioners
- Type
- User and Care
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI