Thank you for purchasing the RFX962 TWIN SPIN Instrument Stereo Chorus.
The 962 is a unique stereo chorus that allows you to switch between two modula-
tion speeds yielding a rich, rotating speaker type effect. The unit provides full,
smooth sounding chorusing and is also useful for splitting your signal into stereo.
To achieve the best results from your RFX962, please read the following manual
carefully. We sincerely hope you enjoy this product.
INSPECTION
1. Unpack and Inspect the RFX962 package.
Your RFX962 was carefully packed at the factory in a protective carton. Nonethe-
less, be sure to examine the unit and the carton for any signs of damage that may
have occurred during shipping. If obvious physical damage is noticed, contact the
carrier immediately to make a damage claim. We suggest saving the shipping
carton and packing materials for safely transporting the unit in the future.
2. Complete the Warranty Registration Card and return it to the factory.
DESCRIPTION
SPEED 1
SPEED 2DEPTH
RATE
SPD 1 CHORUS
TWIN SPIN
INSTRUMENT CHORUS
MODEL RFX962
B A T T E R Y C O M P A R T M E N T
F O O T P A D
1
F O O T P A D
2
I N S T R U M E N T
I N P U T
A C A D A P T E R
I N P U T
O U T P U T 1
O U T P U T 2
CONTROL DESCRIPTIONS
SPD 1 LED: Indicates which speed control is selected. When lit, the modulation
speed is controlled by SPD1, otherwise the modulation speed is controlled by
SPD2.
CHORUS LED: Indicates the RFX962's operation status. When lit, the effect is on,
when the LED is off - the effect is bypassed.
DEPTH: Adjusts the delay time setting of the modulation circuit. Turning this
control clockwise increases this delay time, thereby making the effect deeper and
more full.
RATE: Controls the amount of time taken to switch from Speed 1 to Speed 2.
Turning this control clockwise increases this time.
SPEED 1: Controls the first speed of the chorusing effect, when the SPD1 LED is
lit.
SPEED 2: Controls the second speed of the chorusing effect, when the SPD1 led
is off.
FOOTPAD 1: Switches the chorus effect between Speed 1 and Speed 2.
FOOTPAD 2: Switches the RFX962 between Chorus and bypass modes.
CONNECTION
AC ADAPTER INPUT: For use with the optional ROLLS PS27 Power Supply; 12
VDC, 150 mA, tip negative.
INSTRUMENT INPUT: 1/4" phone jack for an instrument level signal.
OUTPUTS: 1/4" phone jacks to be connected to other pedals, a recording device,
or an amplifier.
NOTE: Unique to the RFX series of effects pedals is the ability of the output jack
to be used as a headphone output.
SAMPLE SETTINGS
Medium Leslie: Use Footpad 1 to switch between chorus speeds
SPEED 1
SPEED 2DEPTH
RATE
Wild Leslie: Use Footpad 1 to switch between speeds
SPEED 1
SPEED 2DEPTH
RATE
Light Chorus: Using SPD 1 only.
SPEED 1
SPEED 2DEPTH
RATE
Full Chorus: Using SPD 1 only.
SPEED 1
SPEED 2DEPTH
RATE
BATTERY REPLACEMENT
The battery will need to be replaced when the unit will not switch on and off, or
when the SPD 1 and CHORUS LEDs will not go completely out.
To change the battery, remove the battery compartment cover and replaced with a
9-volt (alkaline preferred) battery. The battery cover should be put back in place
with the extending flange toward the output side of the pedal.
Completely remove the battery if the unit is being operated with an external power
supply (ROLLS PS27), or if the unit is not going to be used for an extended period
of time.
SPECIFICATIONS
Power Source: 9V battery
Rolls PS27 adapter
Current Draw: 20 mA
Speed Rate: 2Hz - 14Hz
Rate Control: 200mS - 5 Sec.
Avg. Delay Time: 7mS
I/O Connectors: 1/4" TS unbalanced
Size (W x H x D): 3" x 1.2" x 4.8"
Weight: 1 lb.