Samsung HT-AS730ST User manual

Category
AV receivers
Type
User manual

This manual is also suitable for

AV Receiver System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
HT-AS730S
HT-AS730S-XAA_0204.indd 1 2009-02-05 �� 11:46:46
2
Safety information

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous voltage
inside the product that presents a risk of
electric shock or personal injury.
This symbol indicates important instructions
accompanying the product.

To reduce the risk of re or electric shock, do not expose this appliance to rain or moisture.
To prevent injury, this apparatus must be securely attached to the oor/wall in accordance with the installation
instructions.

Apparatus shall not be exposed to dripping or splashing and no objectslled with liquids, such as vases, shall be
placed on the apparatus.
The Mains plug is used as a disconnect device and shall stay readily operable at any time.
This product satises FCC regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with electric appliances, such as radios and televisions, use
shielded cables and connectors for connections.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution : FCC regulations state that any unauthorized changes or modications to this equipment may void the
user's authority to operate it.
~
~
~
~
~
~
~
~

This Compact Disc player is classied as a CLASS 1 LASER product.
Use of controls, adjustments or performance of procedures other than
those specied herein may result in hazardous radiation exposure.
CAUTION
INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN
COVER AND DO NOT REPAIR YOURSELF. REFER
SERVICING TO QUALIFIED PERSONNEL.
~
~
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
HT-AS730S-XAA_0204.indd 2 2009-02-05 �� 11:46:46
3
ENG

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.


This equipment complies with FCC radiation exposure limits set forth an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This digital apparatus (Wireless Internet Radio) does not exceed the Class B limits for radio-noise emissions from
digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep
these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these Instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8)
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does nott into your outlet, consult an
electrician for replacement of the obsolete outlet.
10)
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11) Only use attachment/accessories specied by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualied service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
HT-AS730S-XAA_0204.indd 3 2009-02-05 �� 11:46:47
4

Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install
your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure
the ventilation slots are not covered. Do not stack anything on top of the amplifier. In order to disconnect the player completely
from the power supply, remove the mains plug from the wall outlet, especially when left unused for a long period of time.
Protect the player from moisture(i.e. vases) , and excess
heat(e.g.fireplace) or equipment creating strong magnetic
or electric fields (i.e.speakers...). Disconnect the power
cable from the AC supply if the player malfunctions. Your
player is not intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc have been
stored in cold temperatures.
If transporting the player during the winter, wait
approximately 2 hours until the unit has reached room
temperature before using.
During thunderstorms, disconnect AC main plug from the
wall outlet.
Voltage peaks due to lightning could damage the unit.
Do not expose the unit to direct sunlight or other heat
sources.
This could lead to overheating and malfunction of
the unit.
The batteries used with this product contain
chemicals that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
HT-AS730S-XAA_0204.indd 4 2009-02-05 �� 11:46:48
5
EnG
Digital AV Receiver
This product is a pure digital AV receiver that performs
digital signal processing to minimize signal distortion and
loss.
Dolby Pro Logic llx
Dolby Pro Logic IIx is a new technology that provides
discrete 7.1 channels out of 2 channel or multi channel
sources.It also provides Music,Movie and Game modes.
Dolby Pro Logic Iix is an improved surround system that
is optimized to a 7.1 CH multimedia system, enabling
you to maximize your entertainment experience.
DTS 96/24
DTS 96/24 encodes standard 16 bit/44.1 kHz sound to
24 bit/96kHz and applies it to a 5.1 CH sound track.
DOLBY DIGITAL EX
Adds a surround back channel for more spacious sound
compared to regular 5.1 channel Dolby Digital.
DTS (Digital Theater Systems)
DTS provides a discrete 5.1 CH digital audio signal for
both music and movie contents and uses less
compression than Dolby Digital for richer sound.
iPod
You can enjoy music les by connecting your iPod
to the AV Receiver with the supplied iPod dock.
DTS
Provides a full range of 6 channels by converting a digital
PCM or analog stereo signal using DTS digital matrix
decoding.
SFE (Sound Field Effect) Using
32bit Audio Digital Signal
Processing
Provides more realistic surround sound with normal
stereo audio sources.
Anynet+ (HDMI-CEC) Function
Anynet+ is a function that can be used to operate this
AV Receiver with a Samsung TV remote control, by
connecting the receiver to a SAMSUNG TV using an
HDMI Cable. (This function is available only in
connection with Samsung TV and DVD player
supporting Anynet+(HDMI-CEC).)
DTS-ES
(Extended Surround)
The DTS-ES (Extended Surround) system is a new multi
digital signal format that was developed by Digital
Theater Systems Inc.
Supporting full compatibility with the conventional DTS
digital surround sound format, the DTS-ES (Extended
Surround) system improves the surround signal for a
360-degree surround effect.
DTS-ES adds an additional rear center surround channel
for 6.1 channel sound.
Features
ACCESSORIES
Remote control
(AH59-01951K)
FM antenna
(AH42-00017A)
User’s manual
(AH68-02174R)
iPod Dock
(AH97-02650C)
ASC microphone
( AH30-00099A )
HT-AS730S-XAA_0205.indd 5 2009-02-05 �� 3:58:48
6
Contents

2
2 SafetyWarnings
3 ImportantSafetyInstructions
4 Precautions

5
5 Accessories

8
8 FrontPanel
10 RearPanel
12 Display
13 InsertRemoteControlBatteries
13 OperationRangeoftheRemoteControl
14 TouroftheRemoteControl

16
16 SpeakerPositioning
18 ConnectingtheSpeakers
19 ConnectingtheVideoOuttoyourTV
20 ConnectingExternalDevices/yourTVvia
HDMI
21 HDMIFunction
22 ConnectingaDVDorBD(Blu-Ray)Player
23 ConnectingaCable,SatelliteorSet-topBox
24 ConnectingaVCR
25 ConnectingaCDPlayer
26 Connecting7.1ChannelDevices
27 ConnectinganiPod
29 ConnectingtheFMAntenna
29 ConnectingAuxComponents

30
30 SetupMenuTree
34 InputSetup
35 SpeakerSetup
39 SurroundSetup
44 OptionSetup

47
47 BeforeUsingtheAVReceiver
48 SelectingDigital/AnalogInput
49 UsingtheSurroundModes
52 UsingtheSpeakerAdjustmentButtons
53 ListeningtotheRadio
54 UsinganiPod
56 ConvenientFunctions
HT-AS730S-XAA_0204.indd 6 2009-02-05 �� 11:46:53
7
EnG contents
troubleshooting
61
61 Troubleshooting
appendix
63
63 Specications
miscellaneous
58
58 OperatingYourTVwiththeRemoteControl
60 OperatingYourDVDorBDPLAYER withthe
Remote Control
HT-AS730S-XAA_0205.indd 7 2009-02-05 �� 3:59:01
8
Description

1
STANDBY/ON button Sets the AV receiver to Standby.
2
VOLUME Control Adjusts the volume level.
3
SELECT button Used to change the radio frequency or select detailed options in Surround mode.
4
TUNING MODE button
Used to select Manual or Auto mode for FM radio.
5
TONE CONTROL button
Used to adjust the bass and treble level.
* Also used to return to the previous menu from the SETUP menu.
6
S.DIRECT
Used to output 2 CH PCM audio signal without any signal processing, providing higher audio quality.
This is useful for obtaining the best sound from a connnected CD player.
* Also used to select an item in the SETUP menu.
7
SURROUND button Toggles to select a surround sound mode.
* Also used to move the cursor up in the SETUP menu.
11 10 9 8 7 6 5 4 3
21
14 121315
HT-AS730S-XAA_0204.indd 8 2009-02-05 �� 11:46:54
9
ENG 
8
7.1CH IN Used to select a connected 7.1 multi channel player
* Also used to move the cursor down in the SETUP menu.
9
FUNCTION button Used to select a source (FM, DVD, SAT, TV, VCR, CD, AUX, 7.1 MULTI CH)
* Also used to move the cursor to the right in the SETUP menu.
10
INPUT MODE Toggles to select an input mode for the selected source.
* Also used to move the cursor to the left in the SETUP menu.
11
SETUP button Displays the SETUP menu where you can select a menu item (INPUT, SPEAKER, SURROUND,
OPTION).
12
ASC MIC JACK Used to connect the ASC MIC for setting up ASC (Auto Sound Calibration).
13
AUX IN Jack Auxiliary AV input terminals used to connect a camcorder, portable DVD player or gaming device.
14
HEADPHONE Jack Stereo headset input jack.
15
POWER button Turns the receiver on/off.
HT-AS730S-XAA_0204.indd 9 2009-02-05 �� 11:46:54
10

1
FM Antenna JACK Connect the FM Antenna here.
2
7.1 CH ANALOG AUDIO INPUT JACKS
Receives the analog audio signal from an external player with a multi-channel port.
3
VIDEO INPUT JACKS Receives the video signal from a video player (DVD, SAT, TV, VCR).
4
HDMI INPUT JACKS
Receives digital video and audio signals simultaneously using an HDMI cable.
5
VCR VIDEO OUTPUT JACK
Outputs the video signal to the VCR.
6
MONITOR OUTPUT JACK Outputs the video signal to video devices (TV, Projector etc).
7
HDMI OUTPUT JACK Outputs digital video and audio signals simultaneously using an HDMI cable.
8
SPEAKER OUTPUT TERMINALS
Speaker connection terminals
9
COMPONENT VIDEO OUTPUT JACK Outputs the component video signal.
10
COMPONENT VIDEO INPUT JACKS Receives the component video signal.
11
SUBWOOFER AUDIO OUTPUT JACK Connect the subwoofer.
IPOD
1 2 3 5 64 7 8
17 16 14 13 12 10 91115
HT-AS730S-XAA_0204.indd 10 2009-02-05 �� 11:46:56
11
ENG 
12
CD AUDIO INPUT JACKS Receives the audio signal from an audio CD player.
13
VCR AUDIO OUTPUT JACK Outputs the audio signal to a VCR.
14
AUDIO INPUT JACKS Receives the audio signal from a video player.
15
IPOD INPUT JACK Receives the audio/video signal from an iPod.
16
COAXIAL INPUT JACK (DIGITAL AUDIO IN)
Receives the digital coaxial audio signal.
17
OPTICAL INPUT JACKS
(DIGITAL AUDIO IN)
Receives the digital optical audio signal.
HT-AS730S-XAA_0204.indd 11 2009-02-05 �� 11:46:56
12

1
SPEAKER INDICATORS Receives the audio/video signal from an iPod.
2
LISTENING MODE INDICATORS Displays the current listening mode.
3
TUNING INDICATORS Displays the status of the current radio broadcasting.
4
AUDIO INPUT INDICATORS Displays the input signal type of the current audio source.
5
VOLUME LEVEL INDICATOR Displays the volume level.
6
RADIO FREQUENCY INDICATOR Displays the current radio frequency range.
7
MESSAGE DISPLAY Informs you of the status of the receiver.
1 2 43
67
5
HT-AS730S-XAA_0204.indd 12 2009-02-05 �� 11:46:57
13
EnG 


Place batteries in the remote control so they match the polarity : (+) to (+) and (–) to (–).
Use the correct type of batteries. Batteries that look similar may differ in voltage.
Always replace both batteries at the same time.
Do not expose the batteries to heat or a ame.

The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also be operated at a
horizontal angle of up to 3from the remote control sensor.
M
1. Liftthecoveratthebackofthe
remotecontrolupwardasshown.
2. InstalltwoAAAsizebatteries.
Make sure to match the “+” and “–”
ends of the batteries with the diagram
inside the compartment.
3. Replacethecover.
Assuming typical TV usage, the
batteries last for about one year.
HT-AS730S-XAA_0205.indd 13 2009-02-05 �� 4:00:14
14
Tour of The remoTe ConTrol
HT-AS730S-XAA_0213.indd 14 2009-02-16 �� 2:54:57
15
ENG 
1
POWER button Turns the receiver on/off.
2
INPUT MODE button Toggles to select an input mode for the selected source.
3
SLEEP button Used to set the Sleep Timer.
4
NUMBER buttons Used to select a TV channel.
5
SPK LEVEL/ SPK SELECT/
TEST TONE buttons
Used to select and adjust the level of a desired speaker. Also used to select the Test Tone
function.
6
MO/ST button Select MONO or STEREO for radio broadcasting.
7
TUNER MEMORY button Used to set a preset radio frequency.
8
VOLUME CONTROL buttons Adjusts the volume of the selected device.
9
S.DIRECT button Used to output 2CH PCM audio without any signal processing, providing higher audio quality.
This is useful for obtaining the best sound from a connected CD player.

SETUP/MENU button Displays the SETUP menu where you can select a menu item (INPUT, SPEAKER, SURROUND,
OPTION).

UP/DOWN/LEFT/RIGHT
buttons Used to navigate the menus.

INFO button Displays information on the connected device currently being used.

SURROUND mode buttons Used to select a surround sound mode.

STEREO button Outputs the sound of the selected source in 2 CH stereo.

DIMMER button Adjusts the brightness of the display.

FUNCTION button Toggles tond and select an input source.

SELECT DEVICE buttons Select one from the 4 provided sources that you want to control using the remote control.

PAUSE button Pauses playback on a connected device.

TUNING MODE button Used to select Auto or Manual mode for FM radio.

EXTERNAL DEVICE
PLAYBACK buttons Used to control playback functions on external devices.

MUTE button Mutes the sound of a connected device.

TUNING/CHANNEL buttons Used to change the radio broadcasting frequency or TV channel.

RETURN button Used to return to the previous menu from the SETUP menu.

ENTER button Used to select an item in the SETUP menu.

EXIT button Exits the SETUP menu.

ASC button Used to set the ASC function.

FUNCTION selector buttons Used to select an input source.
HT-AS730S-XAA_0204.indd 15 2009-02-05 �� 11:46:59
16


Place AV Receiver on a dedicated stand or rack.

SBL SBR
The position of the subwoofer is not so critical. Place it
anywhere you like.

Active subwoofer with integrated 150W amplier provides rich
bass sound.
Connect the SW OUT terminal of the amplier to the
INPUT terminal of the subwoofer speaker.
Press the POWER button on the rear side of the subwoofer to turn the power on.
Using the subwoofer’s VOLUME control, you can set the desired bass level
(See page 37 "Setting the speaker level" to set the subwoofer level in the menu).

SBL SBR
SBL SBR
Place these speakers in front of your listening position, facing inwards (about 45°) toward you.
Place the speakers so that their tweeters will be at the same height as your ears.
Align the front face of the front speakers with the front face of the center speaker or place them slightly
in front of the center speaker.
~
~
~
SL SR
SBL SBR
Connections
This section involves various methods of connecting the AV receiver to other
external components.
Before moving or installing the product, be sure to turn off the power and
disconnect the power cord.
HT-AS730S-XAA_0204.indd 16 2009-02-05 �� 11:47:01
17
ENG 


SBL SBR
It is best to install it at the same height as the front speakers.
You can also install it directly over or under the TV.

SBL SBR
SBL SBR
Place these speakers behind your listening position.
If there isn't enough room, place these speakers so they face each other.
Place them about 2 to 3 feet (60 to 90cm) above your ears, facing slightly downward.
Unlike the front and center speakers, the surround speakers are used to handle mainly sound effects
and sound will not come from them all the time.

SBL SBR
SBL SBR
If you are using two rear center speakers, place them facing forward from behind the listening position.
Place the surround back speaker about 2.3-3.3feet (70 cm to 1 m).
When you attach the speakers to a wall, make sure to fasten them tightly so they do not fall off.

For the best surround-sound experience, you should connect seven speakers and a powered
subwoofer.
The following table shows which channels you should use based on the number of speakers you have.
2 speakers 3 speakers 4 speakers 5 speakers 6 speakers 7 speakers
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
SBL SBR
If you’re using only one surround back speaker, connect it to the SURR BACK L terminals.
No matter how many speakers you use, a powered subwoofer is recommended for powerful and solid bass.
M`
M`
`
HT-AS730S-XAA_0204.indd 17 2009-02-05 �� 11:47:02
18


Loosen the knob by turning counterclockwise.
Insert the bare part of the wire into the hole in the side of
each terminal.
Tighten the knob by turning clockwise to secure the wire.
Keep the subwoofer speaker out of reach of children to prevent them from inserting their hands or objects
into the duct (hole).
Never touch speaker terminals while the power is on. Doing so could result in electric shock.
Make sure the polarities (+ and -) are correct.

Press down the terminal tab on the back of the speaker.
Insert the black wire into the black terminal (–) and the red wire into the
red (+) terminal, and then release the tab.
Connect the connecting plugs to the back of the AV Receiver.
Make sure the colors of the speaker terminals on the back of the
AV receiver match the colors of the connecting plugs.



M`
`
`



~
AV RECEIVER
SURROUND (R)
SURROUND (L)
SURROUND
BACK (L)
(not supplied)
SURROUND
BACK (R)
(not supplied)
FRONT (L)
FRONT (R)
ACTIVE SUBWOOFER
(BUILT-IN POWER AMPLIFIER)
CENTER
Black Red
HT-AS730S-XAA_0204.indd 18 2009-02-05 �� 11:47:08
19
EnG 


If your television is equipped with Component Video inputs, connect a Component video cable(not
supplied) from the Component Video Output (PR, PB and Y) jacks on the back of your AV Receiver to the
Component Video Input jacks on your TV.
OR
Connect the Video cable from the VIDEO OUT (MONITOR) jack on the back of your AV Receiver to the
Video Input jack on your TV.

Connect the Digital Input (OPTICAL 3) on your AV Receiver to the Digital Output of the TV.
OR
Connect AUDIO IN (TV) on your AV Receiver to the Audio Out of the TV.
OPTICAL
OUT
AUDIO
OUT
VIDEO
IN
COMPONENT
IN
HT-AS730S-XAA_0206.indd 19 2009-02-06 �� 9:42:51
20

HDMI is a digital standard interface for connection to such devices as a TV, projector, DVD player, Blu-ray player, settop
box and more.
HDMI removes any loss of signal from analog conversion, enabling you to enjoy video and audio sound quality as it was
originally created in the digital source.
By connecting through the HDMI(High-Denition Multimedia Interface) interface, you can play back digital video and audio.

To play digital contents through the HDMI connection, both of the connected external device and TV
must support High-bandwidth Digital Content Protection System (HDCP). This product supports HDCP.
Compatibility with a TV Supporting HDMI
A TV with an HDMI jack. Video/Audio
A TV with a DVI-D jack (TV supporting HDCP) Video
A TV with a DVI-D jack (TV not supporting HDCP) -
Audio from SACD discs will not be heard. To play a DVD disc whose copyright is protected by CPPM, use a
player supporting CPPM.
The quality of the audio output through the HDMI jack (sampling frequency and bit rate) may be limited by the
performance of the connected device.
Since HDMI connection supports both video and audio, you don’t have to connect an additional audio cable.
M`
`
`
Connect it if you want
to use Anynet+.
TV
OPTICAL
OUT
DVD or Blu-RAY Player SAT(Cable/Satellite/Set-top box) Game console
HT-AS730S-XAA_0204.indd 20 2009-02-05 �� 11:47:13
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66

Samsung HT-AS730ST User manual

Category
AV receivers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI