Chief Fusion FLR100 Installation guide

Chief
Brand
Chief
Model
Fusion FLR100
Category
Mounting kits
Type
Installation guide

Chief Fusion FLR100 is an accessory designed to extend the capabilities of your wall-mounted display by allowing you to attach speakers to the sides of the display. It is compatible with both large and extra-large displays, with a maximum spacing of 70" for large displays and 84" for extra-large displays. The FLR100 is capable of supporting up to 20 lbs of weight on each side, making it suitable for a variety of speaker types. It comes with all the necessary hardware for installation, including knobs for vertical leveling of the speakers.

Chief Fusion FLR100 is an accessory designed to extend the capabilities of your wall-mounted display by allowing you to attach speakers to the sides of the display. It is compatible with both large and extra-large displays, with a maximum spacing of 70" for large displays and 84" for extra-large displays. The FLR100 is capable of supporting up to 20 lbs of weight on each side, making it suitable for a variety of speaker types. It comes with all the necessary hardware for installation, including knobs for vertical leveling of the speakers.

INSTALLATION INSTRUCTIONS
Side Speakers Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FLR100
FLR100 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located on the FLR100 does not exceed
20 lbs (9.1 kg) on each side.
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Installation Instructions FLR100
3
DIMENSIONS
13.78
350
0
.
0
0
31
1.22
40.5
1.59
50
1.97
81
3.19
9
0
.
5
3
.
5
6
1
0
0
3
.
9
4
1
3
1
5
.
1
6
1
4
0
.
5
5
.
5
3
1
5
0
5
.
9
1
1
8
1
7
.
1
2
1
9
0
.
5
7
.
5
0
2
0
0
7
.
8
7
2
3
1
9
.
0
9
2
4
0
.
5
9
.
4
7
2
5
0
9
.
8
4
2
8
1
1
1
.
0
6
2
9
0
.
5
1
1
.
4
4
3
0
0
1
1
.
8
1
3
3
1
1
3
.
0
3
3
4
0
.
5
1
3
.
4
0
1
5
.
0
0
3
8
1
5
1
D
I
S
T
A
N
C
E
F
R
O
M
W
A
L
L
2
.
0
1
8
.
0
0
4
5
7
.
2
MAXIMUM SPACING WHEN USED WITH
LARGE SERIES
70" (1778 mm)
MAXIMUM SPACING WHEN USED WITH
EXTRA LARGE SERIES
84" (2134 mm)
MINIMUM SPACING WHEN USED WITH
LARGE SERIES
40.25" (1022 mm)
MINIMUM SPACING WHEN USED WITH
EXTRA LARGE SERIES
54.25" (1378 mm)
7
.
1
.
2
8
25.4
1.00
2.57
65.4
FLR100 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
1/2"
A (1)
B (1)
C (2)
D (4)
1/4-20 x 1/2"
E (4)
1/4"
F (4)
1/4"
G (2)
[Left Speaker
Extension]
[Right Speaker
Extension]
[Speaker
Bracket]
[Knob]
Installation Instructions FLR100
5
ASSEMBLY AND INSTALLATION
NOTE: Dependent on display size, the FLR100 may be
installed while the display is attached to the wall mount.
If not, remove display before proceeding.
Attaching to Wall Mount
1. Remove end caps from wall mount rails. (See Figure 1)
Figure 1
2. Install and tighten the knob (G) on each speaker extension.
(See Figure 2)
Figure 2
3. Slide FLR100 into wall mount rails. (See Figure 3)
4. Tighten the side speaker bushings into the wall mount rails.
(See Figure 3)
NOTE: It may be necessary to lift slightly on the FLR100 in
order to tighten the side speaker bushings.
1
(G) x 2
2
Figure 3
FUSION Mount
(A)
3
Side Speaker Bushing
for Minimum Extension
Side Speaker Bushing
for Maximum Extension
FLR100 Installation Instructions
6
Attaching Speakers and Brackets
1. Attach speakers (not included) to speaker brackets (C)
following instructions included with speakers.
2. Loosely attach one 1/4-20 x 1/2" hex head cap screw (D),
one 1/4" lock washer (E) and one 1/4" flat washer (F) to top
of each of the speaker brackets (C). (See Figure 4)
3. Hang speaker brackets (with attached speakers) on the left
and right speaker extensions, and loosely attach bottom of
speaker brackets (C) to speaker extensions using one
1/4-20 x 1/2" hex head cap screw (D), one 1/4" lock washer
(E) and one1/4" flat washer (F) on each speaker extension.
(See Figure 4)
Figure 4
4. Push speakers into desired position by lifting slightly on
speakers to enable them to slide more easily.
5. Adjust and level speaker brackets (C) using lower slot. (See
Figure 4)
6. Tighten all four fasteners.
7. Turn knob (G) outward on both left and right speaker
brackets until the knob contacts the wall. This will allow
vertical leveling of the speakers.
(D) x 2
(F) x 2
2
(E) x 2
(A)
(C)
3
5
[left speaker end cap (A) shown]
Lower Slot
Installation Instructions FLR100
7
FLR100 Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
F 877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
F +31 (0)40 2668615
Asia Pacific A Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
P +86-755-8996 9226
F +86-755-8996 9217
Chief Manufacturing, a products division
of Milestone AV Technologies
8807-000083
2009 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
01/09
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief Fusion FLR100 Installation guide

Chief
Brand
Chief
Model
Fusion FLR100
Category
Mounting kits
Type
Installation guide

Chief Fusion FLR100 is an accessory designed to extend the capabilities of your wall-mounted display by allowing you to attach speakers to the sides of the display. It is compatible with both large and extra-large displays, with a maximum spacing of 70" for large displays and 84" for extra-large displays. The FLR100 is capable of supporting up to 20 lbs of weight on each side, making it suitable for a variety of speaker types. It comes with all the necessary hardware for installation, including knobs for vertical leveling of the speakers.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents