Page is loading ...
Slide Hammer and
Bearing Puller Set
95987 Bearing Puller Set
INSTRUCTIONS AND
PRECAUTIONS
Visit our website at:
http://www.harborfreight.com
Read this material before
using this product.
Failure to do so can result
in serious injury.
SAVE THIS MANUAL.
When unpacking, make sure
that the product is intact and
undamaged.
If any parts are missing or broken,
please call 1‑800‑444‑3353
as soon as possible.
Copyright
©
2011 by Harbor Freight Tools
®
.
All rights reserved. No portion of this document
or any artwork contained herein may be
reproduced in any shape or form without the
express written consent of Harbor Freight
Tools. Diagrams within this document may
not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly
from the product described herein. Tools required
for assembly and service may not be included.
For technical questions or replacement
parts, please call 1‑800‑444‑3353.
Page 2 For technical questions, please call 1‑800‑444‑3353. SKU 95987
Specications
Collet Size /
Bearing Depth
3/8 IN. ~ 1/2 IN.
(1‑1/2 IN. Max. Bearing
Depth / 3/4 IN. Hex Drive)
9/16 IN. ~ 11/16 IN.
(1‑3/4 IN. Max. Bearing
Depth / 3/4 IN. Hex Drive)
5/8 IN. ~ 1 IN.
(1‑3/4 IN. Max Bearing
Depth / 3/4 IN. Hex Drive)
1 IN. ~ 1‑1/4 IN.
(2 IN Max. Bearing Depth
/ 1 IN. Hex Drive)
Slide Hammer
Weight
3 LB. with Handle
1.95 LB. without Handle
Important Safety Information
Assembly Precautions
1. Assemble only according to
these instructions. Improper
assembly can create hazards.
2. Wear ANSI‑approved safety
goggles and heavy‑duty work
gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the
area during assembly.
5. Do not assemble when tired
or when under the inuence
of drugs or medication.
Use Precautions
1. This product is not a toy. Do not allow
children to play with or near this item.
2. Use as intended only.
3. Inspect before every use; do not
use if parts are loose or damaged.
4. Maintain product labels and
nameplates. These carry important
safety information. If unreadable
or missing, contact Harbor Freight
Tools for a replacement.
Operating Instructions
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of
this document including
all text under subheadings
therein before set up or
use of this product.
1. After threading the proper Attachment
(3, 4, 5 or 6) onto the end of the Slide
Hammer (1) make sure the clamps of
the Attachment are completely closed.
NOTE: To open or close the
Attachment Clamps, grasp the
Attachment head rmly and twist
the Handle (2) of the Slide Hammer.
A clockwise motion will open the
clamps, while counterclockwise
motion will close them.
2. Insert the Attachment head into the
inner diameter of the bearing.
3. Grasp the Attachment head while
turning the Handle clockwise until
the Attachment clamps open and are
are snug against the bearing lining.
4. Firmly grasp the Slide Hammer and
Handle with both hands. Spread
your feet shoulder‑width apart.
5. Gently push Slide Hammer forward.
Make sure your ngers are not in
the way of the sliding action.
6. Forcefully pull Slide Hammer backward
towards your body. Watch bearing
for movement. Bearing should pull
out evenly. If the Bearing pulls out
unevenly during this operation, stop.
Page 3For technical questions, please call 1‑800‑444‑3353.SKU 95987
Remove the Bearing Puller and gently
tap the bearing with a rubber mallet
until it is even, then start again.
7. Repeat steps 4 thru 6 until bearing has
successfully pulled free of its location.
8. Close the Attachment clamps by
twisting Handle counterclockwise.
Then remove the bearing.
Maintenance and Servicing
1. BEFORE EACH USE, inspect the
general condition of the Bearing Puller.
Check for loose attachments, binding
of moving parts, cracked or broken
Attachments, and any other condition
that may affect its safe operation. If
any abnormality is found, have the
problem corrected before further use
2. AFTER EACH USE, wipe off Bearing
Puller with clean, moist cloth.
3. Lubricate attachments regularly
to ensure smooth operation.
4. Replace attachment if threads begin
wear and will not attach to Slide
Hammer.
Record Serial Number Here:
Note: If product has no serial
number, record month and
year of purchase instead.
PLEASE READ THE FOLLOWING CAREFULLY
NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES
ANY REPRESENTATION OR WARRANTY OF ANY KIND TO
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE
ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED
AND LICENSED TECHNICIANS, AND NOT BY THE BUYER.
THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT
OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Part Description Qty
1 Slide Hammer 1
2 Handle 1
3 Attachment 3/8” to 1/2” 1
1
2
3
4 5
6
Parts List and Diagram
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser that this
product is free from defects in materials and workmanship for the period of 90 days
from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside
our facilities, criminal activity, improper installation, normal wear and tear, or to lack of
maintenance. We shall in no event be liable for death, injuries to persons or property,
or for incidental, contingent, special or consequential damages arising from the use
of our product. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation of exclusion may not apply to you. THIS
WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to
us with transportation charges prepaid. Proof of purchase date and an explanation
of the complaint must accompany the merchandise. If our inspection veries
the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you
with a replacement. We will return repaired products at our expense, but if we
determine there is no defect, or that the defect resulted from causes not within the
scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specic legal rights and you may
also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
/