Lincoln Electric Handy MIG Operating instructions

Brand: Lincoln Electric

Model: Handy MIG

Category: Welding System

Type: Operating instructions

Handymig 170i

OPERATOR’S MANUAL

IM796

April, 2006

Safety Depends on You

LiquidArc machines are designed

and built with safety in mind.

However, your overall safety can

be increased by proper installation

... and thoughtful operation on

your part. DO NOT INSTALL,

OPERATE OR REPAIR THIS

EQUIPMENT WITHOUT READ-

ING THIS MANUAL AND THE

SAFETY PRECAUTIONS CON-

TAINED THROUGHOUT. And,

most importantly, think before you

act and be careful.

For use with machine Code Numbers

10984

A Division of Lincoln Electric Company (Aust) Ply Ltd A.B.N. 36 000 040 308

35 Bryant Street, Padstow, NSW2211, Australia

Made exclusive for Australia

This manual covers equipment which is no

longer in production by The Lincoln Electric Co.

Specications and availability of optional

features may have changed.

FOR ENGINE

powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance

work unless the maintenance work requires it to be running.

------------------------------------------------------------------------

1.b. Operate engines in open, well-ventilated

areas or vent the engine exhaust fumes

outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame

welding arc or when the engine is running.

Stop the engine and allow it to cool before

refueling to prevent spilled fuel from vapor-

izing on contact with hot engine parts and

igniting. Do not spill fuel when filling tank. If

fuel is spilled, wipe it up and do not start

engine until fumes have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers

and devices in position and in good

repair.Keep hands, hair, clothing and tools

away from V-belts, gears, fans and all

other moving parts when starting, operating

or repairing equipment.

____________________________________________________

SAFETY

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.

KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

For more detailed information it is strongly recommended that you purchase a copy of "Safety in Welding and Cutting - ANSI

Standard Z49.1" and WTIA Technical Note 7. All WTIA publications and ANSI/AWS Standards are available from the

Welding Technology Institute of Australia, PO Box 6165 Silverwater NSW 2128. For copies of various Australian Standards

contact your local S.A.A. office.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE

PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

WARNING

1.h. To avoid scalding, do not remove the

radiator pressure cap when the engine is

hot.

1.e. In some cases it may be necessary to remove safety

guards to perform required maintenance. Remove

guards only when necessary and replace them when the

maintenance requiring their removal is complete.

Always use the greatest care when working near moving

parts.

___________________________________________________

1.f. Do not put your hands near the engine fan. Do not attempt to

override the governor or idler by pushing on the throttle control

rods while the engine is running.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while

turning the engine or welding generator during maintenance

work, disconnect the spark plug wires, distributor cap or

magneto wire as appropriate.

Oct ‘00

SAFETY

2.i.4 Connect the work cable to the work piece as close as

possible to the area being welded. (This is also a good

practice to eliminate a common problem on welding - a

poor work connection.

2.i.5 Do not work next to the welding power source.

ADDITIONAL PRECAUTIONS FOR

WELDERS WITH PACEMAKERS

2.j. There is no question that the fields in arc welding can interfere

with a pacemakers function. Generally the interference does

not permanently damage the pacemaker. Once the wearer

leaves the arc welding environment or stops welding, the pace-

maker returns to normal functioning. The welding arc has little

or no effect on the operation of some pacemakers, especially

designs that are bi-polar or designed to filter out such interfer-

ence.

2.k. For a welder or anyone working around electrical equipment

the selection of a pacemaker is very important. Get a doctor’s

advice about which pacemaker is the least sensitive to inter-

ference from welding while still being medically suitable.

2.l. In addition to the normal safety precautions, the following addi-

tional procedures should be adopted by welders with pacemak-

ers.

2.l.1 Use gas welding when the application is suitable.

2.l.2 Use the lowest current setting appropriate for the applica-

tion. Do not exceed 400 amps. Low current (75-200

amps) direct current (DC) welding should be used if arc

welding is necessary. Do not TIG weld with high frequen-

cy.

2.l.3 Do not use repeated, short welds. Wait about ten sec-

onds between stopping one weld and starting the next.

When having difficulty starting an electrode, do not re-

strike the rod repeatedly.

2.l.4 If you feel light headed, dizzy or faint, immediately stop

welding. Lay the electrode holder down so that it does not

contact the work and move away from any welding being

performed. Arrange your work in advance so that, if you

become dizzy and drop the electrode holder it will not fall

on your body or strike the work.

2.l.5 Do not work on a ladder or other elevated position or in a

cramped, confined place.

2.l.6 Do not work alone. Work only in the presence of an indi-

vidual who understands these precautions and the possi-

ble effect welding may have on your pacemaker.

2.l.7 Do not work near spot welding equipment.

2.l.8 If you have a pacemaker and wish to continue arc weld-

ing, discuss this and any other questions you may have

with your physician and follow his or her advice. The doc-

tor may wish to contact the pacemaker manufacturer for a

recommendation. As mentioned before, the design of the

pacemaker significantly affects the degree to which it is

subject to interference from a welding circuit. Do not rely

on the fact that you know another welder with a pacemak-

er who has welded for years without experiencing a prob-

lem.That welder and his or her pacemaker may be quite

different from you and your pacemaker.

ELECTRIC AND

MAGNETIC FIELDS

may be dangerous

2.a. Electric current flowing through any conductor causes

localized Electric and Magnetic Fields (EMF). Welding

current creates EMF fields around welding cables and

welding machines

2.b. EMF fields may interfere with some pacemakers, and

welders having a pacemaker should consult their physician

before welding.

2.c. Exposure to EMF fields in welding may have other health

effects which are now not known.

2.d. All welders should follow safe practices that minimize their

exposure to electric and magnetic fields (EMF).

2.e. For welders wearing implanted pacemakers, safe welding

practices are particularly important and additional procedures

should be followed by those who have decided to continue to

weld. (Hopefully in keeping with a doctor’s advice).

2.f. The following procedures will not eliminate exposure to EMF or

the possibility of arc welding having an effect on a pacemaker,

however if followed, they will significantly reduce exposure to

electric and magnetic fields. Electric and magnetic fields are

created any time electric current flows through a conductor,

however it is not clear whether such exposure affects ones

health.

2.g. Some researchers have reported that exposure to EMF may

cause leukemia or other illnesses. These claims originally

arose in relation to high voltage electric power lines and are

very much in dispute in the medical and scientific arena, how-

ever the best advice is to minimize your exposure to EMF to

protect your health should doctors eventually decide there is a

risk.

2.h. There are four fundamental facts about EMF:

2.h.1 With direct current (DC), the field strength is relatively

constant and does not change.

2.h.2 With alternating current (AC), the field strength constant-

ly changes.

2.h.3 The greater the current flow, i.e. the higher the amps,

the stronger the field created by the current

2.h.4 The closer the conductor or electrical device is to the

body the greater the exposure to the field.

MINIMIZE EXPOSURE TO EMF

2.i. All welders should use the following procedures to minimize

EMF exposure:

2.i.1 Route electrode or gun and work cables together. Secure

them with tape if possible.

2.i.2 Never coil the electrode lead around your body.

2.i.3 Do not place your body between the electrode and work

cables. If your electrode cable is on your right side the

work cable should also be on your right side.

Oct ‘00

iii

SAFETY

iii

ARC RAYS can burn.

4.a. Use a shield with the proper filter and cover

plates to protect your eyes from sparks and

the rays of the arc when welding or observing

open arc welding. Headshield and filter lens

should conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant

material to protect your skin and that of your helpers from

the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable

screening and/or warn them not to watch the arc nor expose

themselves to the arc rays or to hot spatter or metal.

ELECTRIC SHOCK can

kill.

3.a. The electrode and work (or ground) circuits

are electrically “hot” when the welder is on.

Do not touch these “hot” parts with your bare

skin or wet clothing. Wear dry, hole-free

gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.

Make certain the insulation is large enough to cover your full

area of physical contact with work and ground.

In addition to the normal safety precautions, if welding

must be performed under electrically hazardous

conditions (in damp locations or while wearing wet

clothing; on metal structures such as floors, gratings or

scaffolds; when in cramped positions such as sitting,

kneeling or lying, if there is a high risk of unavoidable or

accidental contact with the workpiece or ground) use

the following equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,

electrode reel, welding head, nozzle or semiautomatic

welding gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical

connection with the metal being welded. The connection

should be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical

(earth) ground.

3.f.

Maintain the electrode holder, work clamp, welding cable and

welding machine in good, safe operating condition. Replace

damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of

electrode holders connected to two welders because voltage

between the two can be the total of the open circuit voltage

of both welders.

3.i. When working above floor level, use a safety belt to protect

yourself from a fall should you get a shock.

3.j. Also see Items 6.c. and 8.

FUMES AND GASES

can be dangerous.

5.a. Welding may produce fumes and gases

hazardous to health. Avoid breathing these

fumes and gases.When welding, keep

your head out of the fume. Use enough

ventilation and/or exhaust at the arc to keep

fumes and gases away from the breathing zone. When

welding with electrodes which require special

ventilation such as stainless or hard facing (see

instructions on container or MSDS) or on lead or

cadmium plated steel and other metals or coatings

which produce highly toxic fumes, keep exposure as

low as possible and below Threshold Limit Values (TLV)

using local exhaust or mechanical ventilation. In

confined spaces or in some circumstances, outdoors, a

respirator may be required. Additional precautions are

also required when welding on galvanized steel.

5.b.

Do not weld in locations near chlorinated hydrocarbon

vapors

coming from degreasing, cleaning or spraying operations.

The heat and rays of the arc can react with solvent vapors

form phosgene, a highly toxic gas, and other irritating prod-

ucts.

5.c. Shielding gases used for arc welding can displace air and

cause injury or death. Always use enough ventilation,

especially in confined areas, to insure breathing air is safe.

5.d. Read and understand the manufacturer’s instructions for this

equipment and the consumables to be used, including the

material safety data sheet (MSDS) and follow your

employer’s safety practices. MSDS forms are available from

your welding distributor or from the manufacturer.

5.e. Also see item 1.b.

Mar ‘95

FOR ELECTRICALLY

powered equipment.

8.a. Turn off input power using the disconnect

switch at the fuse box before working on

the equipment.

8.b. Install equipment in accordance with the National

Electrical Code, all local codes and the manufacturer’s

recommendations.

8.c. Ground the equipment in accordance with the National

Electrical Code and the manufacturer’s recommendations.

CYLINDER may explode

if damaged.

7.a. Use only compressed gas cylinders

containing the correct shielding gas for the

process used and properly operating

regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for

the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely

chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected to

physical damage.

• A safe distance from arc welding or cutting operations and

any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other

electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet

when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand

tight except when the cylinder is in use or connected for

use.

7.g. Read and follow the instructions on compressed gas

cylinders, associated equipment, and CGA publication P-l,

“Precautions for Safe Handling of Compressed Gases in

Cylinders,” available from the Compressed Gas Association

1235 Jefferson Davis Highway, Arlington, VA 22202.

SAFETY

Mar ‘95

WELDING SPARKS can

cause fire or explosion.

6.a.

Remove fire hazards from the welding area.

If this is not possible, cover them to prevent

the welding sparks from starting a fire.

Remember that welding sparks and hot

materials from welding can easily go through small cracks

and openings to adjacent areas. Avoid welding near

hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site,

special precautions should be used to prevent hazardous

situations. Refer to “Safety in Welding and Cutting” (ANSI

Standard Z49.1) and the operating information for the

equipment being used.

6.c. When not welding, make certain no part of the electrode

circuit is touching the work or ground. Accidental contact

can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the

proper steps have been taken to insure that such procedures

will not cause flammable or toxic vapors from substances

inside. They can cause an explosion even

though

they have

been “cleaned”. For information, purchase “Recommended

Safe Practices for the

Preparation

for Welding and Cutting of

Containers and Piping That Have Held Hazardous

Substances”, AWS F4.1 from the American Welding Society

(see address above).

6.e. Vent hollow castings or containers before heating, cutting or

welding. They may explode.

6.f.

Sparks and spatter are thrown from the welding arc. Wear oil

free protective garments such as leather gloves, heavy shirt,

cuffless trousers, high shoes and a cap over your hair. Wear

ear plugs when welding out of position or in confined places.

Always wear safety glasses with side shields when in a

welding area.

6.g. Connect the work cable to the work as close to the welding

area as practical. Work cables connected to the building

framework or other locations away from the welding area

increase the possibility of the welding current passing

through lifting chains, crane cables or other alternate cir-

cuits. This can create fire hazards or overheat lifting chains

or cables until they fail.

6.h. Also see item 1.c.

SAFETY

INSTRUCTIONS FOR ELECTRO-

MAGNETIC COMPATIBILITY

Conformance

Products displaying the C-Tick mark are in conformity with

Australian/New Zealand requirements for Electromagnetic

Compatibility (EMC) according to standard (emission) AS/NZS

3652 "Electromagnetic Compatibility – Arc Welding

Equipment".

Products displaying the CE mark are in conformity with

European Community Council Directive 89/336/EEC require-

ments for EMC by implementing EN50199 "Electromagnetic

Compatibility (EMC) – Product standard for arc welding equip-

ment".

Products are:

• For use with other Lincoln Electric/LiquidArc equipment.

• Designed for industrial and professional use.

Introduction

All electrical equipment generates small amounts of electromagnet-

ic emission. Electrical emission may be transmitted through power

lines or radiated through space, similar to a radio transmitter. When

emissions are received by other equipment, electrical interference

may result. Electrical emissions may effect many kinds of electrical

equipment: other nearby welding equipment, radio and TV trans-

mitters and receivers, numerical controlled machines, telephone

systems, computers, etc. Be aware that interference may result

and extra precautions may be required when a welding power

source is used in a domestic establishment.

Installation and Use

The purchaser/user is responsible for installing and using the weld-

ing equipment according to the manufacturer’s instructions. If elec-

tromagnetic disturbances are detected then it shall be the responsi-

bility of the purchaser/user of the welding equipment to resolve the

situation with the technical assistance of the manufacturer. In some

cases this remedial action may be as simple as earthing (ground-

ing) the welding circuit (see note below). In other cases it could

involve constructing an electromagnetic screen enclosing the

power source and the work complete with associated input filters.

In all cases electromagnetic disturbances must be reduced to the

point where they are no longer troublesome.

Note: The welding circuit may or may not be earthed for safety rea-

sons according to national codes. Changing the earthing arrange-

ments should only be authorized by a person who is competent to

assess whether the changes increase the risk of injury, eg. by

allowing parallel welding current return paths which may damage

the earth circuits of other equipment.

Assessment of Area

Before installing welding equipment the purchaser/user shall make

an assessment of potential problems in the surrounding area.

The following shall be taken into account:

• Other supply cables, control cables, signalling and telephone

cables above, below and adjacent to the welding equipment;

• Radio and television transmitters and receivers;

• Computer and other control equipment;

• Safety critical safety equipment, eg. guarding of industrial

equipment;

• The health of people around, eg. the use of pacemakers and

hearing aids;

• Equipment used for calibration or measurement;

• The immunity of other equipment in the environment. The

purchaser/user shall ensure that other equipment being used

in the environment is compatible. This may require additional

protection measures;

• The time of the day that welding or other activities are to be

carried out.

The size of the surrounding area to be considered will depend on

the structure of the building and other activities that are taking

place. The surrounding area may extend beyond the boundaries of

the premises.

Methods of Reducing Emissions

Mains Supply

Welding equipment should be connected to the mains supply

according to the manufacturer’s recommendations.If interference

occurs, it may be necessary to take additional precautions such as

filtering the mains supply. Consideration should be given to shield-

ing the supply cable of permanently installed welding equipment in

metallic conduit or equivalent. Shielding should be electrically con-

tinuous throughout its length. The shielding should be connected to

the welding power source so that good electrical contact is main-

tained between the conduit and the welding power source enclo-

sure.

Maintenance of the Welding Equipment

The welding equipment should be routinely maintained according

to the manufacturer’s recommendations. All access and service

doors and covers should be closed and properly fastened when the

welding equipment is in operation. The welding equipment should

not be modified in any way except for those changes and adjust-

ment covered in the manufacturer’s instructions. In particular, the

spark gaps of arc initiation and stabilizing devices should be adjust-

ed and maintained according to the manufacturer’s recommenda-

tions.

Welding Cables

The welding cables should be kept as short as possible and should

be positioned close together, running at or close to the floor level.

Equipotential Bonding

Bonding of all metallic components in the welding installation and

adjacent to it should be considered. However, metallic components

bonded to the work piece will increase the risk that the operator

could receive a shock by touching these metallic components and

the electrode at the same time. The operator should be insulated

from all such bonded metallic components.

Earthing of the workpiece

Where the workpiece is not bonded to earth for electrical safety,

nor connected to earth because of its size and position, eg. ship’s

hull or building steelwork, a connection bonding the workpiece to

earth may reduce emissions in some, but not all instances. Care

should be taken to prevent the earthing of work pieces increasing

the risk of injury to users, or damage to other electrical equipment.

Where necessary, the connection of the workpiece to earth should

be made by direct connection to the workpiece, but in some coun-

tries where direct connection is not permitted, the bonding should

be achieved by suitable capacitance, selected according to national

regulations.

Screening and Shielding

Selective screening and shielding of other cables and equipment in

the surrounding area may alleviate problems of interference.

Screening of the entire welding installation may be considered for

special applications.

Portions of the preceding text are extracted from:

• Australian/New Zealand standard AS/NZS 3652. Permission to

reproduce has been granted by Standards Australia and

Standards New Zealand. For further explanation, readers should

be referred to the standard itself.

• British Standards Institution standard BS EN 50199:1995.

Reproduced with permission of BSI under license number

2000SK0631. Complete standards can be obtained from BSI

Customer Services, 389 Chiswick High Road, London W4 4AL.

United Kingdom. (Tel +44 (0) 20 8996 9001).

Standards New Zealand and British Standards Institution.

Permission to reproduce the text must be obtained.

JAN ‘01

vivi

Thank You

for selecting a QUALITY product by Lincoln Electric. We want you

to take pride in operating this Lincoln Electric Company product

••• as much pride as we have in bringing this product to you!

Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it

handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.

The level of seriousness to be applied to each is explained below:

WARNING

This statement appears where the information must be followed exactly to avoid serious personal injury or

loss of life.

This statement appears where the information must be followed to avoid minor personal injury or damage to

this equipment.

CAUTION

Please Examine Carton and Equipment For Damage Immediately

When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims

for material damaged in shipment must be made by the purchaser against the transportation company at the

time the shipment is received.

Please record your equipment identification information below for future reference. This information can be

found on your machine nameplate.

Product _________________________________________________________________________________

Model Number ___________________________________________________________________________

Code Number or Date Code_________________________________________________________________

Serial Number____________________________________________________________________________

Date Purchased___________________________________________________________________________

Where Purchased_________________________________________________________________________

Whenever you request replacement parts or information on this equipment, always supply the information you

have recorded above. The code number is especially important when identifying the correct replacement parts.

On-Line Product Registration

- Register your machine with Lincoln Electric either via fax or over the Internet.

• For faxing: Complete the form on the back of the warranty statement included in the literature packet

accompanying this machine and fax the form per the instructions printed on it.

• For On-Line Registration: Go to our

WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then

“Product Registration”. Please complete the form and submit your registration.

vii

TABLE OF CONTENTS

Page

Installation .......................................................................................................Section A

Technical Specifications ........................................................................................A-1

Identify and Locate Components...........................................................................A-2

Select Suitable Location ........................................................................................A-3

Stacking ..........................................................................................................A-3

Tilting...............................................................................................................A-3

Output Connections...............................................................................................A-3

Work Clamp Installation ..................................................................................A-3

Work Cable Installation ...................................................................................A-4

Gun Installation......................................................................................................A-4

Connecting Gun Cable to the Handymig 170i.................................................A-4

Gas Connection.....................................................................................................A-4

Input Connections..................................................................................................A-5

Electrical Input Connection for Rated Output ........................................................A-6

Line Cord Connection .....................................................................................A-6

Operation .........................................................................................................Section B

Safety Precautions ................................................................................................B-1

General Description...............................................................................................B-1

Recommended Processes ..............................................................................B-1

Optional Features and Controls ......................................................................B-1

Design Features and Advantages .........................................................................B-1

Welding Capability.................................................................................................B-2

Limitations..............................................................................................................B-2

Controls and Settings ............................................................................................B-2

Welding Operations ...............................................................................................B-3

Sequence of Operations .................................................................................B-3

Wire Loading ..............................................................................................B-3

Friction Brake Adjustments ........................................................................B-3

Wire Threading...........................................................................................B-4

Making a Weld ...........................................................................................B-5

Cleaning Tip and Nozzle ............................................................................B-5

Process Guidelines................................................................................................B-5

Changing Over to Feed Other Wire Sizes .............................................................B-6

Welding with GMAW..............................................................................................B-6

Welding with FCAW...............................................................................................B-6

Application Chart.................................................................................................B-7

Handymig 170i

viii

TABLE OF CONTENTS

Page

Maintenance ....................................................................................................Section D

Safety Precautions ................................................................................................D-1

Routine Maintenance.............................................................................................D-1

Wire Feed Compartment.................................................................................D-1

Fan Motor........................................................................................................D-1

Wire Reel Spindle ...........................................................................................D-1

Gun and Cable................................................................................................D-1

Gun Cable Cleaning................................................................................D-1

Contact Tips, Nozzles, and Gun Tubes ..................................................D-1

Component Replacement Procedures ..................................................................D-2

Changing the Contact Tip ...............................................................................D-2

Changing Drive Roll ........................................................................................D-2

Changing Liner................................................................................................D-3

Gun Handle Parts ...........................................................................................D-3

Ground Test Procedure.........................................................................................D-4

Troubleshooting..............................................................................................Section E

Safety Precautions.................................................................................................E-1

How to Use Troubleshooting Guide.......................................................................E-1

Troubleshooting Guide.............................................................................E-2 thru E-4

Wiring Diagrams..............................................................................................Section F

Handymig 170i Wiring Diagram .............................................................................F-1

Handymig 170i Parts ............................................................................P463,P202,P189

Handymig 170i

A-1

INSTALLATION

Fuse or

Output Mode Input Voltage Breaker Size Input Amps Power Cord

RATED 240V/50Hz 25 Super Lag 12.7 15Amp, 240V,

Three Pin Plug

TECHNICAL SPECIFICATIONS – Handymig 170i

INPUT – SINGLE PHASE ONLY

RATED OUTPUT

OUTPUT

RECOMMENDED INPUT CABLE AND FUSE SIZES

Height Width Depth Weight

305 mm 248 mm 419 mm 25.9 kg

PHYSICAL DIMENSIONS

Standard Voltage/Frequency AS1966.1

240V/50Hz Rated Input Current

12.7 Amps

Duty

Cycle Amps Volts at Rated Amperes

20% 130 20

Welding

Current Range Maximum Open Circuit Voltage Auxiliary Power

Rated DC Output: 30 – 170 amps 33 N/A

Handymig 170i

A-2

INSTALLATION

SAFETY PRECAUTIONS

• Read entire installation section before starting

installation.

IDENTIFY AND LOCATE

COMPONENTS

If you have not already done so, unpack the

Handymig 170i from its carton and remove all packing

material around the Handymig 170i. Remove the fol-

lowing loose items from the carton (see Figure A.1):

1. Handymig 170i

2. Gun and cable assembly

(1)

3. Literature and miscellaneous includes:

a) This operating manual

b) A separate .030" (0.8 mm) contact tip

c) Hex key wrench for removal of drive roll.

4. 10 ft (3,0 m) work cable.

5. Work clamp.

6. Adjustable mixed-Gas Regulator & Hose.

(1)

The gun is ready to feed .023" – .025" (0.6 mm)

diameter wire.

ELECTRIC SHOCK can kill.

• Only qualified personnel should perform

this installation.

• Only personnel that have read and under-

stood the Handymig 170i Operating

Manual should install and operate this

equipment.

• Machine must be plugged into a receptacle

which is grounded per any national, local

or other applicable electrical codes.

• The Handymig 170i power switch is to be

in the OFF (“O”) position when installing

work cable and gun and when connecting

power cord to input power.

WARNING

FIGURE A.1

Handymi

WELDING AMP RANGEWELDING AMP RANGE

25-125 25-12

A-2

Handymig 170i

A-3

INSTALLATION

SELECT SUITABLE LOCATION

Locate the welder in a dry location where there is free

circulation of clean air into the louvers in the back and

out the front of the unit. A location that minimizes the

amount of smoke and dirt drawn into the rear louvers

reduces the chance of dirt accumulation that can block

air passages and cause overheating.

STACKING

Handymig 170i’s cannot be stacked.

TILTING

Each machine must be placed on a secure, level sur-

face, either directly or on the recommended cart. The

machine may topple over if this procedure is not fol-

lowed.

OUTPUT CONNECTIONS

Refer to Figure A.2.

1. Work Cable Access Hole.

2. Gun Cable and Control Lead Access Hole.

3. Connector Block.

4. Gun Trigger Lead Connectors.

5. Positive (+) and negative (–) output terminals.

6. Wire Feed Gearbox.

7. Cable Hanger.

8. Thumbscrew.

Work Clamp Installation

Attach the work clamp per the following: Refer to

Figure A-3.

Handymig 170i

WELDING AMP RANGE

30-70

FIGURE A.3

1. Insert the work cable terminal lug with the larger

hole through the strain relief hole in the work clamp

as shown above.

2. Fasten securely with the bolt and nut provided.

FIGURE A.2

A-3

Handymig 170i

A-4

INSTALLATION

Work Cable Installation

Refer to Figure A.2.

1. Open the wire feed section door on the right side of

the Handymig 170i.

2. Pass the end of the work cable that has the termi-

nal lug with the smaller hole through the Work

Cable Access Hole (1) in the case front.

3. Route the cable under and around the back of the

Wire Feed Gearbox (6).

4. For GMAW Only: Refer to Figure A.2. As deliv-

ered, the machine is connected for positive elec-

trode polarity. This is the appropriate configuration

for the GMAW (MIG) process. To complete installa-

tion, use the provided wing nut to connect the work

cable’s terminal lug to the negative (–) output ter-

minal (5) located above the Wire Feed Gearbox

(6). Make sure that both wing nuts are tight.

5. For Innershield Only: Refer to Figure A.4. To wire

for negative polarity (required for the Innershield

process), connect the short cable attached to the

connector block (1) to the negative (–) output termi-

nal (2) and the work cable (3) to the positive (+) ter-

minal (4).

FIGURE A.4

NOTE: If .045" or 1.2 mm) Innershield flux-cored wire

is to be used, the appropriate Innershield kit is

required.

Connecting Gun Cable to the Handymig

170i.

1. Refer to Figure A.2. Unplug the machine or turn

power switch to the OFF “O” position.

2. Pass the insulated terminals of the gun trigger con-

trol leads, one at a time, through the Gun Cable

and Control Lead Access Slot (2) in the case front.

The leads are to be routed up the inside of the

case front, behind the gas line.

3. Insert the connector on the gun conductor cable

through the Gun Cable Access Hole (2) in the

Handymig 170i case front. Make sure the connec-

tor is all the way in the brass connector block to

obtain proper gas flow. If the gun connector will not

fully insert, unscrew the thumbscrew on the con-

nector block a few turns. Rotate the connector so

control leads are on the underside and tighten the

Thumbscrew on the connector block.

4. Connect the gun trigger control lead terminals to

the two insulated 1/4" (6,4 mm) tab terminal con-

nector bushings located above the “Gun Trigger

Connection” decal in the wire feed section (4).

Either lead can go to either connector.

If the gun trigger switch being used is other than

that supplied, the switch must be a normally open,

momentary switch. The terminals of the switch

must be insulated from the welding circuit.

Malfunction of the Handymig 170i may result if

this switch shorts to the Handymig 170i welding

output circuit or is common to any electrical cir-

cuit other than the Handymig 170i trigger circuit.

GAS CONNECTION

The Handymig 170i is supplied with a mixed gas

Regulator and a 3m gas hose. A cylinder of an appro-

priate shielding gas must be obtained from your gas

distributor.

CAUTION

GUN INSTALLATION

As shipped from the factory, the Handymig 170i gun is

ready to feed .023" – .025"(.6mm) solid wire. If .030"-

.035” (0.8-.09 mm) solid wire is to be used, change the

contact tip to the appropriate size. If .035” Flux-cored

wire is to be used, change the contact tip and nozzle

to the appropriate types and orient the drive roll to the

appropriate groove size

Handymig 170i

A-5

INSTALLATION

BE SURE TO KEEP YOUR FACE AWAY FROM THE

VALVE OUTLET WHEN “CRACKING” THE VALVE.

Never stand directly in front of or behind the flow

regulator when opening the cylinder valve. Always

stand to one side.

3. Attach the flow regulator to the cylinder valve and

tighten the union nut securely with a wrench..

4. Refer to Figure A.6. Attach one end of inlet gas

hose to the outlet fitting of the flow regulator and

tighten the union nut securely with a wrench.

Connect the other end to the Handymig 170i Gas

Solenoid Inlet Fitting (5/8-18 female threads — for

CGA — 032 fitting). Make certain the gas hose is

not kinked or twisted.

5. Reinstall case side before connecting input power.

INPUT CONNECTIONS

FIGURE A.6

Refer to Figure A.6.

CYLINDER may explode if dam-

aged. Keep cylinder upright and

chained to support

• Keep cylinder away from areas

where it may be damaged.

• Never lift welder with cylinder

attached.

• Never allow welding electrode to

touch cylinder.

• Keep cylinder away from welding

or other live electrical circuits.

BUILDUP OF SHIELDING GAS may

harm health or kill.

• Shut off shielding gas supply

when not in use.

1. Chain the cylinder to a wall or other stationary sup-

port to prevent the cylinder from falling over.

Insulate the cylinder from the work circuit and earth

ground. Refer to Figure A.5.

FIGURE A.5

2. With the cylinder securely installed, remove the

cylinder cap. Stand to one side away from the out-

let and open the cylinder valve very slightly for an

instant. This blows away any dust or dirt which may

have accumulated in the valve outlet.

WARNING

Cylinder Valve

Gas Hose

Flow Regulator

WARNING

POWER INPUT

CABLE

GAS SOLENOID

INLET FITTING

A-5

Handymig 170i

A-6

INSTALLATION

ELECTRICAL INPUT CONNECTION

FOR RATED OUTPUT

ELECTRIC SHOCK can kill.

• Disconnect input power by

removing plug from receptacle

before working inside Handymig

170i.

• Use only grounded receptacle.

• Do not touch electrically “hot”

parts inside Handymig 170i.

• Have qualified personnel do the

maintenance and troubleshooting

work.

Line Cord Connection

A three conductor line cord with a 15 amp, 240 volt,

three pin plug is factory installed. Connect this plug to

a mating grounded receptacle which is connected to

an appropriate power supply per the Wiring Rules and

any applicable local codes.

• This welding machine must be connected to a

power source in accordance with applicable

electrical codes.

• If there is any question about the installation

meeting applicable electrical code requirements,

consult a qualified electrician.

WARNING

A-6

Handymig 170i

B-1

OPERATION

SAFETY PRECAUTIONS

ELECTRIC SHOCK can kill.

• Do not touch electrically live

parts or electrode with skin or

wet clothing. Insulate yourself

from work and ground.

• Always wear dry insulating

gloves.

FUMES AND GASES can be

dangerous.

• Keep your head out of fumes.

• Use ventilation or exhaust to

remove fumes from breathing

zone.

WELDING SPARKS can

cause fire or explosion.

• Keep flammable material away.

• Do not weld on closed contain-

ers.

ARC RAYS can burn eyes

and skin.

• Wear eye, ear and body protec-

tion.

See additional warning information at

front of this operator’s manual.

WARNING

GENERAL DESCRIPTION

The Handymig 170i is a complete semiautomatic con-

stant voltage DC portable arc welder. Included is a

tap-switch controlled, single phase constant voltage

transformer/rectifier power source and a wire feeder

with welding gun for feeding .023" (0.6 mm) through

.030" (0.8 mm) solid steel electrode. Optional kits are

available for .035" (0.9 mm) and .045" (1.2 mm)

Innershield

NR-211-MP.

It is ideally suited for individuals having access to 240

volts 50 Hz AC input power and want the ease of use,

quality and dependability of both gas metal arc weld-

ing or GMAW (also known as MIG welding) and the

Innershield

process (self-shielded flux-cored or

FCAW). A convenient chart is mounted inside the wire

feed section door for setting welding procedures for 24

gauge (.60 mm) through 5/16" (8.0 mm) mild steel.

The machine is rugged and reliable and has designed

for dependable service and long life.

RECOMMENDED PROCESSES

The Handymig 170i can be used for welding mild steel

using the GMAW, single pass, process which requires

a supply of shielding gas or it can be used with the

self-shielded, Innershield

process (FCAW).

OPERATIONAL FEATURES AND

CONTROLS

The Handymig 170i has the following controls as stan-

dard: Power ON/OFF Switch, Voltage Control, Wire

Speed Control, Trigger Switch, and a Circuit Breaker.

DESIGN FEATURES AND

ADVANTAGES

• “Cold electrode” until gun trigger is pressed for an

added measure of safety.

• Overload protection — incorporates both a thermo-

stat and a circuit breaker.

• Quality wire drive with electronic overload protection.

• “Quick Release” idle roll pressure arm is easily

adjusted.

• Reversible, dual groove drive roll, shipped ready to

feed .023"/.025" (0.6 mm) diameter wire. The drive

roll is easily reversed to feed .030" (0.8 mm) diame-

ter solid wire and .035" (0.9 mm) flux-cored diameter

wire. Optional drive roll included in .045" (1.2 mm)

Innershield

welding kit must be installed to feed

.045" (1.2 mm) flux-cored wire.

• No external shielding gas is required when used with

Liquid Arc steelcore 71T-GS electrode.

• Spindle accommodates both 8 in. (200 mm) diameter

and 4 in. (100 mm) diameter spools of wire.

B-1

Handymig 170i

B-2

OPERATION

WELDING CAPABILITY

The Handymig 170i is rated at 130 amps, 20 volts, at

20% duty cycle on a ten minute basis. It is capable of

higher output currents at lower duty cycles. .

LIMITATIONS

Arc Gouging cannot be performed with the Handymig

170i. The Handymig 170i is not recommended for pipe

thawing or TIG welding.

CONTROLS AND SETTINGS

Refer to Figure B.1a.

1. Power ON/OFF Switch —

When the power is on the

fan motor will run and air will

be exhausted out the louvers

in the front of the machine.

The welding output and wire

feeder remain off until the

gun trigger is pressed.

2. Wire Speed Control —

Controls the wire feed speed

from 50 – 400 in/min (1.2 –

10.2 m/min). The control can

be preset on the dial to the

setting specified on the

Handymig 170i Application

Chart located on the inside

of the wire feed section door.

3. Voltage Control — A 5-posi-

tion tap selector switch gives

full range adjustment of

power source output voltage.

Do not switch while welding.

4. Circuit Breaker – Protects machine from damage if

maximum output is exceeded. Button will extend

out when tripped (Manual reset).Refer to Figure

B.1b.

OFF

ARC VOLTS

WIRE SPEED

FIGURE B.1a

FIGURE B.1b

Handymig 170i

B-3

OPERATION

WELDING OPERATIONS

SEQUENCE OF OPERATION

Wire Loading

Refer to Figure B.2 and B.3.

The machine power switch should be turned to the

OFF (“O”) position before working inside the wire feed

enclosure.

The machine is shipped from the factory ready to feed

8” (200 mm) diameter spools [2.2” (56 mm) max.

width]. These spools fit on a 2” (50 mm) diameter

spindle that has a built-in adjustable friction brake to

prevent overrun of the spool and excess slack in the

wire.

Note:When loading and removing the 8” Spools

make

sure that the wing nut (inside the wire spool spindle

hub) is turned 90° from the wire spool spindle locking

tab. If the wing nut is positioned in line with the locking

tab, the tab cannot be depressed to load or unload

the wire spool.

Load an 8” (200 mm) diameter spool on the wire spool

spindle shown in Figure B.2.

To use 4” (100 mm) diameter spools, the 2” (50 mm)

diameter spindle must be removed (See Figure B.3).

Remove the wing nut and spacer at the end of the

shaft and remove the outside plastic wire spool spin-

dle. The spindle can be stored in the wire feed com-

partment. A 4” (100 mm) diameter spool is mounted

directly on the 5/8” (16 mm) diameter shaft and held in

place with the previously removed hardware. Also

make certain the start end of the wire, which may pro-

trude through the side of the spool does not contact

any metallic case parts.

Note: The brake should be adjusted with a spool of

wire installed. When properly adjusted it should

move freely but not coast.

Some spools can have the start wire protruding

from the side of the spool. This must be insulated

from internal metal components otherwise electri-

cal grounding faults will result and the machine

will be seriously damaged.

Friction Brake Adjustments

1. With wire spool installed, check free movement

and coast of the spool.

2. To tighten the brake turn the wing nut clockwise in

1/4 turn increments until coasting stops.

3. To loosen the brake turn the wing nut counter-

clockwise in 1/4 turn increments until the wire spool

moves freely without coasting.

FIGURE B.2

FIGURE B.3

Wire Spool must be pushed all the way on the spindle so that the

spindle’s tab will hold it in place. The Wire Spool will rotate clock-

wise when wire is dereeled.

8” Wire Spool

To Wire Drive

Wire Spool Spindle

Be sure that this stud engages

the hole in the wire spool.

Wire Spindle Shaft

4" Wire Spool

Wing Nut

and Spacer

To wire drive

CAUTION

B-3

Handymig 170i

B-4

OPERATION

Wire Threading

Refer to Figure B.4

1. Release the Spring Loaded Pressure Arm (1)

rotate the Idle Roll Arm (2) away from the Wire

Feed Drive Roll (3). Ensure that the groove size in

the feeding position on the drive roll matches the

wire size being used. See Maintenance section for

further information.

2. Carefully detach the end of the wire from the

spool. To prevent the spool from unwinding, main-

tain tension on the wire until after step 5.

3. Cut the bent portion of wire off and straighten the

first 4” (100 mm).

4. Thread the wire through the incoming guide tube

(4), over the drive roll (3), and into the outgoing

guide tube (5).

5. Close the idle roll arm and latch the spring loaded

pressure arm (2) in place. Rotate the spool coun-

terclockwise if required to take up extra slack in

the wire.

6. The idle roll pressure adjustment wing nut is nor-

mally set for mid-position on the pressure arm

threads. If feeding problems occur because the

wire is flattened excessively, turn the pressure

adjustment counter-clockwise to reduce distortion

of the wire. Slightly less pressure may be required

when using 0.023 – 0.025” (0,6 mm) wire. If the

6. drive roll slips while feeding wire, the pressure

should be increased until the wire feeds properly.

When inching the welding wire, the drive rolls, the

gun connector block and the gun contact tip are

electrically energized relative to work and ground

and remain energized for several seconds after

the gun trigger is released.

------------------------------------------------------------------------

7. Refer to Figure B.5. Remove gas nozzle and con-

tact tip from end of gun.

8. Turn the Handymig 170i ON (“I”).

9. Straighten the gun cable assembly.

10. Depress the gun trigger switch and feed welding

wire through the gun and cable. (Point gun away

from yourself and others while feeding wire.)

Release gun trigger after wire appears at end of

gun.

11. Turn the Handymig 170i OFF (“O”).

12. Replace contact tip and gas nozzle.

13. Refer to Figure B-6. Cut the wire off 3/8”– 1/2” (10

– 12 mm) from the end of the tip. The Handymig

170i is now ready to weld.

WARNING

FIGURE B.4

The Wire Drive Feed Roll can

accommodate two wire sizes by

flipping the wire drive feed roll

over.

FIGURE B.5

Gun Handle

Gas Diffuser/

Contact Tip

Gas Nozzle

Handymig 170i

B-5

OPERATION

Making A Weld

1. See “Process Guidelines” in this section for selec-

tion of welding wire and shielding gas and for

range of metal thicknesses that can be welded.

2. See the Application chart on the inside of the wire

feed compartment door for information on setting

the Handymig 170i controls. Refer to Table B.1 for

aluminum and stainless wire.

3. Set the Voltage (“V”) and Wire Speed (“olo’”) con-

trols to the settings suggested for the welding wire

and base metal thickness being used, refer to

3. Applications chart on the inside of the wire drive

compartment door.

4. Check that the polarity is correct for the welding

wire being used and that the gas supply, if

required, is turned on.

5. When using Innershield electrode, remove the gas

nozzle and install the gasless nozzle. This will

improve visibility of the arc and protect the gas dif-

fuser from weld spatter. Refer to the MAINTE-

NANCE section for details on nozzle replacement.

6. Refer to Figure B.7. Connect work clamp to metal

to be welded. Work clamp must make good elec-

trical contact to the workpiece. The workpiece

must also be grounded as stated in “Arc Welding

Safety Precautions” in the beginning of this manu-

al.

7. Position gun over joint. End of wire may be lightly

touching the work.

8. Lower welding helmet, close gun trigger, and

begin welding. Hold the gun so the contact tip to

work distance is about 3/8 inch (10 mm).

9. To stop welding, release the gun trigger and then

pull the gun away from the work after the arc goes

out.

FIGURE B.6

10. When no more welding is to be done, close valve

on gas cylinder (if used), momentarily operate gun

trigger to release gas pressure, and turn off the

Handymig 170i.

Cleaning Tip And Nozzle

Clean the contact tip and nozzle to avoid arc bridging

between the nozzle and contact tip which can result in

a shorted nozzle, poor welds and an overheated gun.

Hint: Anti-stick spray or gel, available from a welding

supply distributor, may reduce buildup and aid in spat-

ter removal.

PROCESS GUIDELINES

The Handymig 170i can be used for welding mild steel

using the GMAW, single pass, process which requires

a supply of shielding gas or it can be used for the self-

shielded, Innershield

process (FCAW).

The recommended gases and electrodes for GMAW

are welding grade CO

gas or an argon-CO

blended

gas (75 to 80% argon and 25 to 20% CO

) and .025"

(0.6 mm) diameter Liquid Arc S6 mild-steel welding

wire, supplied on 12-1/2 lb (5 kg) spools. The blended

gas is recommended for welding on heavier steel, 14

gauge (2.0 mm), for example.

The recommended electrode for the self-shielded

process is Liquid Arc steelcore 71T-GS on 10 lb (4.5

kg) spools. This electrode is available as .035" (0.9

mm) and .045" (1.2 mm) NR-211-MP for all position

welding of 18 gauge (1.2 mm) through 5/16" (8.0 mm)

steel. Thickness of 1/4" (6.4 mm) and 5/16" (7.9 mm)

require multiple passes. both wire sizes can also be

used for the welding of galvanized coated sheet

metal.

3/8" – 1/2" Contact Tip To Work Distance

(10-12 mm) (CTWD)

Contact Tip

Wire Electrode

FIGURE B.7

WORKPIECE

GUN CABLE

ARC

WORK CLAMP

Handymig 170i

Page is loading ...

Lincoln Electric Handy MIG Operating instructions

Brand: Lincoln Electric

Model: Handy MIG

Category: Welding System

Type: Operating instructions

Download PDF

report

Lincoln Electric Handy MIG Operating instructions

Lincoln Electric Handy MIG Operating instructions

Related papers

Other documents