Hotpoint lft 2294 a ha Owner's manual

Page is loading ...

Operating instructions

Contents

Installation, 14-15

Positioning and levelling

Connecting the water and electricity supplies

Advice regarding the first wash cycle

Technical data

Description of the appliance, 16

Overall view

Control panel

Loading the racks, 17

Lower rack

Cutlery basket

Upper rack

Start-up and use, 18-19

Starting the dishwasher

Measuring out the detergent

Wash options

Wash cycles, 20

Table of wash cycles

Rinse aid and refined salt, 21

Measuring out the rinse aid

Measuring out the refined salt

Care and maintenance, 22

Shutting off the water and electricity supplies

Cleaning the dishwasher

Preventing unpleasant odours

Cleaning the sprayer arms

Cleaning the water inlet filter

Cleaning the filters

Leaving the machine unused for extended periods

Precautions, advice and Assistance,23

General safety

Disposal

Saving energy and respecting the environment

Assistance

Troubleshooting, 24

English,13

EN

LFT 3214

LFT 3204

LFT 2294

DISHWASHER

EN

"

Installation

Keep this instruction manual in a safe place for

future reference. If the appliance is sold, given away or

moved, please ensure the manual is kept with the

machine, so that the new owner may benefit from the

advice contained within it.

Please read this instruction manual carefully: it

contains important information regarding the safe

installation, use and maintenance of the appliance.

If the appliance must be moved at any time, keep it in

an upright position; if absolutely necessary, it may be

tilted onto its back.

Positioning and levelling

1. Remove the appliance from all packaging and check

that it has not been damaged during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Check the dishwasher by placing it so that its sides or

back panel are in contact with the adjacent cabinets or

even with the wall. This appliance can also be recessed

under a single worktop

* (see the Assembly instruction

sheet).

3. Position the dishwasher on a level and sturdy floor. If

the floor is uneven, the front feet of the appliance may be

adjusted until it reaches a horizontal position. If the

appliance is levelled correctly, it will be more stable and

much less likely to move or cause vibrations and noise

while it is operating.

4. Adjust the height of the rear foot from the front of the

appliance

* on the central lower part of the dishwasher, turning

a hexagonal spanner (red color) with an opening of 8 mm in a

clockwise direction to increase the height or in an

anticlockwise direction to decrease the height.

Connecting the water and electricity

supplies

Connection to the water and electricity supplies

should only be performed by a qualified technician.

The dishwasher should not stand on top of the water

hoses or the electricity supply cable.

The appliance must be connected to the water

supply network using new hoses.

Do not use old hoses.

The water inlet (A) and outlet (B) hoses and the

electricity supply cable may be positioned towards the

right or the left in order to achieve the best possible

installation (see figure).

Connecting the water inlet hose

 To a suitable cold water connection point: before

attaching the hose, run the water until it is perfectly

clear so that any impurities that may be present in the

water do not clog the appliance; after performing this

operation, screw the inlet hose tightly onto a tap with

a ¾ gas threaded connection.

 To a suitable hot water connection point: your

dishwasher may be supplied with hot water from the

mains supply (if you have a central heating system

with radiators) provided that it does not exceed a

temperature of 60°C.

Screw the hose to the tap as described for connection

to a cold water supply.

If the inlet hose is not long enough, contact a

specialist store or an authorised technician (see

Assistance).

The water pressure must be within the values

indicated in the Technical data table (see adjacent

information).

The hose should not be bent or compressed.

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the

water supply in the event of anomalies or leaks from

inside the appliance.

Some models are also equipped with the supplementary

safety device New Acqua Stop

*, which guarantees anti-

flooding protection even in the event of a supply hose

rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstance should the water inlet hose be

cut as it contains live electrical parts.

* Only available in selected models.

EN

#

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a drain

duct with a minimum diameter of 4 cm. Alternatively, rest

it over a sink or tub; the free end of the hose should not

remain immersed in water.

The special plastic elbow

*

makes it easier to find the

best layout: fix the elbow to

the wall securely in order to

prevent the outlet hose from

moving and spilling the dirty

water.

The part of the hose marked

with the letter A should be

between 40 and 100 cm

above the ground (see figure).

We advise against the use of hose extensions.

Electrical connection

Before inserting the plug into the electrical socket, make

sure that:

 The socket is earthed and complies with current

regulations.

 The socket can withstand the maximum load of the

appliance, which is indicated on the data plate

located on the inside of the door (see chapter entitled

Description of the appliance).

 The power supply voltage falls within the values

indicated on the data plate on the inside of the door.

 The socket is compatible with the plug of the

appliance. If this is not the case, ask an authorised

technician to replace the plug (see Assistance); do

not use extension cables or multiple sockets.

Once the appliance has been installed, the power

supply cable and the electrical socket should be easily

accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be re-

placed by the manufacturer or its Technical Assistance

Service in order to prevent all potential hazards. (See As-

sistance)

The Company shall not be held responsible for any

incidents that occur if these regulations are not

observed.

Anti-condensation strip*

After installing the dishwasher, open the door and stick

the adhesive transparent strip under the wooden shelf in

order to protect it from any condensation which may

form.

Advice regarding the first wash cycle

After the appliance has been installed, immediately

before running the first wash cycle, completely fill the

salt dispenser with water and add only then

approximately 1 kg of salt (see chapter entitled Rinse aid

and refined salt). The water may overflow: this is normal

and is not a cause for concern. Select the water

hardness value (see chapter entitled Rinse aid and

refined salt). - After the salt has been poured into the

machine, the LOW SALT indicator light

* switches off.

If the salt container is not filled, the water softener

and the heating element may be damaged as a result.

* Only available in selected models.

A

Technical data

Dimensions

width 59.5 cm

height 82 cm

depth 57 cm

Capacity

14 standard place-settings

Water supply

pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

7,25 – 145 psi

Power supply

voltage

See appliance data plate

Total absorbed

power

See appliance data plate

Fuse

See appliance data plate

This dishwasher conforms to

the following European

Community Directives:

-2006/95/CE dated

16/01/2007 (Low Voltage) and

subsequent modifications

-89/336/EEC dated 03/05/89

(Electromagnetic

Compatibility)

and subsequent modifications

-97/17/EC (Labelling)

-2002/96/ CE (Waste

Electrical and Electronic

Equipment WEEE)

EN

$

Overall view

Description of the

appliance

1. Upper rack

2. Upper sprayer arm

3. Tip-up compartments

4. Rack height adjuster

5. Lower rack

6. Lower sprayer arm

7. Cutlery basket

8. Washing filter

9. Salt dispenser

10. Detergent and rinse aid dispensers

11. Data plate

12. Control Panel

***

***Only in completely built-in models.

* Only available in selected models.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Control panel

Option button

ShorTime*

Half load button*

Delayed start button*

ON/OFF/Reset

button

ON/OFF

indicator light

Low salt

indicator light*

Select wash

cycle button

Low rinse aid

indicator light*

Multi-functional tablets

button*

Multi-functional tablets

indicator light*

ShorTime option

indicator light*

Half load upper rack

indicator light*

Half load lower rack

indicator light*

Delayed start

indicator lights*

Good Night

option button*

Good Night option

indicator light*

Wash cycle number

light-up indicator

EN

%

Loading the racks

Before loading the racks, remove all food residues from the

crockery and empty liquids from glasses and cups.

After loading the appliance, check that the sprayer arms

can rotate freely.

Lower rack

The lower rack can hold pans, lids, plates, salad bowls, cutlery,

etc. as seen in the Loading examples.

Plates and large covers should be placed at the sides of the

rack, ensuring that they do not block the rotation of the upper

sprayer arm.

Some dishwasher

models are fitted

with tip-up

sections

*, which

can be used in a

vertical position when arranging plates or in a horizontal position

when arranging pans and salad bowls.

Cutlery basket

The type of cutlery basket may vary according to the

dishwasher model: it may be modular, non-modular or a sliding

version. The non-modular basket must only be positioned at

the front of the lower rack.

The modular basket

may be separated into

two parts, a solution

which is recommended

when performing a half

load wash (only in models offering this option), is available in a

sliding version (positioned at any point on the lower rack by

sliding it between the fixed or tip-up inserts.

- Both versions are fitted with a collapsible sliding system which

means the cutlery can be arranged in the best possible way.

Knives and other utensils with sharp edges must be placed

in the cutlery basket with the points facing downwards, or they

must be positioned horizontally in the tip-up compartments on

the upper rack.

Cutlery basket positioning examples

Upper rack

Load this rack with delicate and lightweight crockery: glasses,

tea and coffee cups, saucers, small salad bowls, saucepans

and small saucepans which are not too soiled, using the

Loading examples as a guide.

 Mugs and cups, long sharp knives and serving utensils:

place these on the tip-up compartments

**.

Tip-up compartments with adjustable tilt

- The tilt feature can be used to increase the space in the upper

rack, to position wine glasses with different stem lengths safely

and to improve drying performance.

- Lift the tip-up compartment, slide it gently and position it in the

desired tilt angle.

Adjusting the height of the upper rack

In order to make it easier to arrange the crockery, the upper rack

may be moved to a higher or lower level.

(in models which offer the Baby cycle, the upper rack must be

placed in its lower position when the appliance is being loaded).

The height of the upper rack should ideally be adjusted

WHEN THE RACK IS EMPTY.

Never lift or lower the rack on one side only.

Open the left and right guide rail stops and

pull out the rack; position it higher or lower

as required, slide it along the guide rails

until the front wheels are in place and close

the stops (see figure).

If the rack is fitted with Dual Space

handles

* (see figure), pull out the upper

rack until it reaches its stop point, grip the

handles at the sides of the rack and move it

upwards or downwards, then slowly let it fall

back into place.

Loading examples for the upper/lower rack

Baby Tip-up compartments

*

For dishwasher models with a Baby Cycle,

tip-up compartments suitable for washing

bottles, rings and teats are provided. (see

the instruction sheet)

Items which should not be washed in the dishwasher

 Wooden items, objects with wooden or horn handles or glued-

on parts.

 Items made from aluminium, copper, brass, pewter or tin.

 Items made from plastic material which is not heat-resistant.

 Antique or hand-painted porcelain.

 Antique silver. Silver which is not antique may, however, be

washed in the dishwasher using a delicate wash cycle,

provided that it does not come into contact with other metals.

We recommend the use of crockery which is dishwasher safe.

* Only available in selected models.

** The number and position may vary.

Tilt A Tilt B Tilt C

EN

&

Start-up and use

Starting the dishwasher

1. Turn the water tap on.

2. Open the door and press the ON/OFF button: you will hear

a short beep and the display and option indicator lights switch

on.

3. Measure out the detergent (see below).

4. Load the racks (see Loading the racks).

5. Select the wash cycle in accordance with the type of

crockery and its soil level (see Table of wash cycles),

by

pressing the P button.

6. Select the wash options (see adjacent information).

7. Start the wash cycle by shutting the door: a long beep

signals the start of the wash cycle.

8. Two short beeps and one long one indicate the end of the

wash cycle and the wash cycle number flashes on the display.

Open the door, switch off the appliance by pressing the ON/

OFF button, shut off the water tap and unplug the appliance

from the electricity socket.

9. Wait for a few minutes before removing the crockery, in

order to avoid burns. Unload the racks, beginning with the

lower level.

AUTO WASH CYCLES

*: this model of dishwasher is

equipped with a special sensor which can be used to assess

the level of soiling and automatically select the most efficient

and economic wash cycle accordingly.

The duration of the auto wash cycles may vary due to the

operation of the sensor.

If the crockery is only lightly soiled or if it has been rinsed

with water before being placed in the dishwasher, reduce the

amount of detergent used accordingly.

Modifying a wash cycle in progress

If a mistake was made during the wash cycle selection

process it is possible to change the cycle, provided that it has

only just begun: open the door, avoiding the escaping steam,

and press and hold the ON/OFF button; the machine will

switch off with a long beep. Switch the machine back on using

the ON/OFF button and select the new wash cycle and any

options desired; start the cycle by closing the door.

Adding extra crockery

Without switching off the machine, open the door, taking care

to avoid the escaping steam, and place the crockery inside

the dishwasher. Close the door: the cycle starts from the point

at which it was interrupted.

Accidental interruptions

If the door is opened during the wash cycle, or if there is a

power cut, the cycle stops. It starts again from the point at

which it was interrupted once the door has been shut or once

the electricity supply is restored.

Measuring out the detergent

A good wash result also depends on the correct amount of

detergent being used; exceeding the stated amount does not

result in a more effective wash and increases environmental

pollution.

Only use detergent which has been

specifically designed for dishwashers.

 DO NOT USE washing up liquid.

Using excessive detergent may result in foam

residue remaining in the machine after the cycle

has ended.

The use of tablets is only recommended for

models which offer the MULTI-FUNCTIONAL

TABLETS option.

To achieve the best results from each washing

and drying cycle, powder detergent, rinse aid

liquid and salt should be used.

Compartment A: Washing detergent

Compartment B: Pre-wash detergent

1. Open cover C by pressing button

D.

2. Pour in the detergent after

consulting the Table of wash cycles:

 For powder detergent use

compartments A and B.

 For detergent in tablet form: when

the cycle requires 1 tablet, place it in

compartment A and close the cover;

when it requires 2, place the second tablet at the bottom of the

appliance.

3. Remove detergent residues from the edges of the

compartment and close the cover until it clicks.

Wash options

If an option is not compatible with the selected was cycle

(see Table of wash cycles), the corresponding LED flashes

rapidly 3 times and 2 short beeps will sound.

Delayed start

It is possible to delay the start time of the cycle by 3, 6 or 9

hours.

1. Press the DELAYED START button: every time it is pressed

a buzzer sounds and the selected period of time is displayed.

2. Select the wash cycle and shut the door: after the beep

sounds, the timer begins counting down.

3. Once this time has elapsed, the indicator light switches off

and the wash cycle begins.

To adjust the delay time and select a smaller period of time,

press the DELAYED START button. To cancel it, press the

button repeatedly until the selected delayed start indicator

light switches off. The wash cycle will start automatically as

soon as the door is shut.

* Only available in selected models.

EN

'

Multi-functional tablets*

This option optimises washing and drying results.

When using multi-functional tablets, press the MULTI-

FUNCTIONAL TABLETS button. The corresponding indicator

light will illuminate. The Multi-functional tablets option results

in the lengthening of the wash cycle.

The MULTI-FUNCTIONAL TABLETS option remains set

for subsequent wash cycles if it is not deselected.

The use of tablets is only recommended for models

which offer the MULTI-FUNCTIONAL TABLETS option.

This option is not recommended for use with wash

cycles which do not specify the use of multi-functional

tablets (see Table of options).

* Only available in selected models.

The ShorTime and Good Night options are not

compatible with each other.

The ShorTime and Good Night options are not

compatible with the HALF LOAD option.

Good Night option*

This option reduces the amount of noise made by the machine

and lengthens the wash cycles. It is a useful option because it

enables users to benefit from the night-time energy rate.

After selecting the wash cycle, press the Good Night option

button; the illumination of the corresponding indicator light

followed by a short beep indicates its selection.

To deselect the option, press the same button again.

Table of options*

A

B

C

D

E

Delayed

Start

Half

Load

Multi-functional

Tablets

ShorTime

Good

Night

1. Auto Intensive

Yes

No

2. Auto Normal

Yes

3. Daily wash

Yes

No

4. Soak

Yes

No

5. Eco

Yes

No

Yes

6. Quick

Yes

No

Yes

No

7. Crystal

Yes

No

8. Auto Duo Wash

Yes

No

Yes

No

9. Ultra Intensive

Yes

No

10. Special Guest Wash

Yes

No

11. Baby cycle

Yes

No

ShorTime option*

This option can be used to reduce the duration of the main

wash cycles while maintaining the same washing and drying

performance levels.

After selecting the wash cycle, press the ShorTime option

button; the illumination of the corresponding indicator light

followed by a short beep indicates its selection.

To deselect the option, press the same button again.

Half load using the upper or lower rack*

If there are not many dishes to be washed, a half load cycle

may be used in order to save water, electricity and detergent.

Select the wash cycle and press the HALF LOAD button

repeatedly: the triangle corresponding to the selected load will

illuminate and the wash cycle will take place only using the

upper or the lower rack.

The Half load option is not compatible with the Good Night

and ShorTime options.

Remember to load the upper or lower rack only, and to

reduce the amount of detergent accordingly.

EN



Wash cycles

For available OPTIONS please refer to the Table of options on the Start-up and use page.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Detergent

(A) = compartment A

(B) = compartment B

Wash cycle selection instructions Wash cycle

Powder Liquid Tablets

Wash

cycles

which

include

drying

Options

Wash cycle

duration

(tolerance

±10%)

Hrs. Min.

Heavily soiled dishes and pans (not to

be used for delicate items). 1. Auto

Intensive

35 g (A)

35 ml (A)

1 (A)

Yes

A–B–C–D

2:15’

Normally soiled pans and dishes.

Standard daily wash cycle.

2. Auto

Normal Wash

29 g (A)

6 g (B)

29 ml (A)

6 ml (B)

1 (A)

Yes

A–B–C-

D–E

1:45’

Limited quantity of daily soiling.

(4 place settings + 1 saucepan +1

frying pan).

3. Daily A 60’

25 g (A)

25 ml (A)

1 (A)

No

A–B– C

1:00’

Pre-wash for dishes while awaiting

completion of the load with the dishes

from the next meal.

4. Soak

No

A – B

0:08’

Environmentally-friendly wash cycle

with low energy consumption levels,

suitable for pans and dishes.

5. Eco

*

29 g (A)

6 g (B)

29 ml (A)

6 ml (B)

1 (A)

Yes

A–B-C-E

2:45’

Economic and fast wash to be used

for lightly soiled dishes. (Run cycle

immediately after use) (2 plates + 2

glasses + 4 pieces of cutlery + 1

saucepan + 1 small frying pan).

6. Quick

25 g (A)

25 ml (A)

1 (A)

No

A - C

0:25’ - 0:35’

Economic and fast wash for delicate

items which are sensitive to high

temperatures. (Run cycle immediately

after use) (glasses upper rack +

delicate plates lower rack). 7. Crystal

35 g (A)

35 ml (A)

1 (A)

Yes

A– B–C

1:30’

Wash spread over the two racks:

delicate for crystal and glasses on the

upper rack and heavy duty for the

pans on the lower rack.

8. Auto

Duo Wash

35 g (A)

35 ml (A)

1 (A)

Yes

A–C–D

1:43’

Heavily soiled saucepans or pans with

residual dried-on food.

9. Ultra Intensive

29 g (A)

6 g (B)

29 ml (A)

6 ml (B)

1 (A)

1 (bottom

of the

appliance)

Yes

A – B – C

2:07'

Rinse and drying cycle for dishes that

are seldom used and are only dusty.

10. Guest Wash

No

Yes

A – B

0:32’

Disinfecting wash cycle suitable for

washing bottles, rings and teats

together with plates, cups, glasses

and cutlery. The crockery should only

be loaded on the upper rack.

11. Baby Wash

20 g (A)

20 ml (A)

No

Yes

A

1:20'

Notes:

Optimum performance levels when using the "Daily wash" and "Quick wash" cycles can be achieved by observing the maximum amounts of

crockery specified.

To make it easier to measure out the detergent, it is worth remembering that:

1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid - 1 teaspoon = 5 gr. of powder = approximately 5 ml of liquid

* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less energy and

is les harmful to the environment.

Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the following address:

[email protected]

EN



Rinse aid and refined salt

Only use products which have been

specifically designed for dishwashers.

Do not use table salt or industrial salt, or

washing up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

rinse aid; however, we recommend that you add salt,

especially if you live in an area where the water is hard or

very hard. Follow the instructions given on the packaging.

If you do not add salt or rinse aid, the LOW

SALT

* and LOW RINSE AID* indicator lights

remain lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water

runs off surfaces more readily and therefore does not leave

streaks or marks.

The rinse aid dispenser should be filled:

 When the LOW RINSE AID

* indicator light on the control

panel is illuminated;

1. Open the dispenser by turning

the lid (G) in an anticlockwise

direction.

2. Pour in the rinse aid, making

sure it does not overflow from the

dispenser. If this happens, clean

the spill immediately with a dry

cloth.

3. Screw the lid back on.

NEVER pour the rinse aid directly into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

may adjust the quantity of rinse aid used. Use a screwdriver

to turn the dosage adjuster (F) to one of the 6 pre-set

positions (the default position is set to 4):

 If there are streaks on the crockery, set the adjustment

device to a lower number (1-3).

 If drops of water remain on the crockery or if there are

limescale marks present after the cycle has finished, set the

adjuster to a higher number (4-6).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of

appliance, supplies water without limescale which is then used

to wash the crockery.

This dishwasher offers a setting which helps to reduce

pollution and optimises washing performance in accordance

with the water hardness level in your area. This information can

be obtained from the organisation which supplies your

household with water.

- Open the door and switch on the machine by pressing the

ON/OFF button.

- Press the P button and hold for approximately 5 seconds;

two short beeps will sound and the set hardness number will

flash slowly on the display (the water softening system is set

to number 3).

- Press the P button repeatedly until the desired hardness

level has been reached (1-2-3-4-5

* see Water hardness

table).

- To exit the function, wait approximately 30 seconds or press

another option button, or switch off the machine using the ON/

OFF button.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH = hardness measured in German degrees - °f =

hardness measured in French degrees - mmol/l = millimoles

per litre)

Measuring out the refined salt

In order to achieve the best possible results using a wash

cycle, make sure that the dispenser is never empty. Refined

salt removes limescale from the water, thus avoiding the

formation of deposits on crockery.

The salt dispenser is located in the lower part of the

dishwasher (see Description) and should be filled:

 When the green float

* cannot be seen by simply looking at

the cap of the salt dispenser.

 When the LOW SALT

* indicator light on the control panel is

illuminated;

1. Remove the lower rack and unscrew

the container cap (anticlockwise).

2. The first time you do this: fill the water

tank right up to its edge.

3. Position the funnel

* (see figure) and fill

the salt container right up to its edge (this

should hold approximately 1 kg); it is not unusual for a little

water to leak out.

4. Remove the funnel

* and wipe any salt residue away from

the opening; rinse the cap under running water and then

screw it on, the head facing downwards so as to let the water

flow out of the four cracks which are arranged in a star shape

on the lower part of the cap. (Salt cap with green float

*)

It is advisable to perform this procedure every time you

add salt to the container.

Make sure the cap is screwed on tightly, so that no detergent

can get into the container during the wash cycle (this could

damage the water softener beyond repair).

When necessary, measure out the salt before a wash

cycle so that any saline solution which has leaked out of the

salt dispenser is removed.

* Only available in selected models.

G

F

Water Hardness Table

°dH °fH mmol/l level

0 6 0 10 0 1 1

6 11 11 20 1.1 2 2

12 17 21 30 2.1 3 3

17 34 31 60 3.1 6 4

34 50 61 90 6.1 9

5

*

For values between 0°f and 10°f, we do not

recommend the use of salt.

* this setting may cause a slight increase in the

duration of the cycle.

EN

Care and maintenance

Shutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle to avoid

leaks.

 Always unplug the appliance when cleaning it and

when performing maintenance work.

Cleaning the dishwasher

 The external surfaces of the machine and the control

panel may be cleaned using a non-abrasive cloth

which has been dampened with water. Do not use

solvents or abrasive products.

 Any marks on the inside of the appliance may be

removed using a cloth dampened with water and a

little vinegar.

Preventing unpleasant odours

 Always keep the door of the appliance ajar in order to

avoid moisture from forming and being trapped inside

the machine.

 Clean the seals around the door and detergent

dispensers regularly using a damp sponge. This will

avoid food becoming trapped in the seals, which is

the main cause behind the formation of unpleasant

odours.

Cleaning the sprayer arms

Food residue may become encrusted onto the sprayer

arms and block the holes used to spray the water. It is

therefore recommended that the arms are checked from

time to time and cleaned with a small non-metallic

brush.

The two sprayer arms may both be removed.

To remove the upper sprayer

arm, rotate the locking ring in

an anti-clockwise direction.

The upper sprayer arm should

be replaced with the holes

facing upwards.

The lower sprayer arm can be

removed by pressing on the

side tabs and pulling it

upwards.

Cleaning the water inlet filter*

If the water hoses are new or have not been used for an

extended period of time, let the water run to make sure it

is clear and free of impurities before performing the

necessary connections. If this precaution is not taken,

the water inlet could become blocked and damage the

dishwasher.

Clean the water inlet filter at the tap outlet regularly.

- Turn off the water tap.

- Unscrew the end of the water inlet hose, remove the filter and

clean it carefully under running water.

- Replace the filter and screw the water hose back into

position.

Cleaning the filters

The filter assembly consists of three filters which remove food

residues from the washing water and then recirculate the

water. They should be cleaned if you wish to achieve the best

results in every wash.

Clean the filters regularly.

The dishwasher should not be used without filters, or if the

filter is loose.

 After several washes, check the filter assembly and if

necessary clean it thoroughly under running water, using a

non-metallic brush and following the instructions below:

1. Turn the cylindrical filter C in an anti-clockwise direction

and pull it out (fig. 1).

2. Remove the cup filter B by exerting a slight pressure on the

side flaps (fig. 2).

3. Slide out the stainless steel plate filter A (fig. 3).

4. Inspect the trap and remove any food residue.

NEVER REMOVE the wash cycle pump (black detail)

(fig. 4).

After cleaning the filters, replace the filter assembly and fix it in

position correctly; this is essential for maintaining the efficient

operation of the dishwasher.

Leaving the machine unused for extended

periods

 Disconnect the appliance from the electricity supply and

shut off the water tap.

 Leave the door of the appliance ajar.

 When you return, run a wash cycle when the dishwasher is

empty.

* Only available in selected models.

1

C

2

C

B

3

A

4

EN

!

Precautions, advice

and Assistance

This appliance was designed and manufactured in

compliance with current international safety standards. The

following information has been provided for safety reasons

and should therefore be read carefully.

General safety

 The appliance was designed for domestic use inside the

home and is not intended for commercial or industrial use.

 The appliance must be used by adults only, to wash

domestic crockery in accordance with the instructions in

this manual.

 The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

machine exposed to rain and storms.

 Do not touch the appliance when barefoot.

 When unplugging the appliance always pull the plug from

the mains socket, do not pull on the cable.

 The water supply tap must be shut off and the plug should

be removed from the electrical socket before cleaning the

appliance or carrying out any maintenance work.

 If the appliance breaks down, do not under any

circumstances touch the internal parts in an attempt to

perform the repair work yourself.

 Never touch the heating element.

 Do not lean or sit on the open door of the appliance: this

may cause the appliance to overturn.

 The door should not be left open as it may create a

dangerous obstacle.

 Keep detergent and rinse aid out of reach of children.

 The packaging material should not be used as a toy.

Disposal

 Disposal of packaging materials: observe local legislation

so that the packaging may be reused.

 The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that

household appliances should not be disposed of using the

normal solid urban waste cycle. Exhausted appliances

should be collected separately in order to optimise the cost

of re-using and recycling the materials inside the machine,

while preventing potential damage to the atmosphere and

to public health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations regarding

separated waste collection.

For further information relating to the correct disposal of

household appliances, owners may contact the relevant

public authority or the local appliance dealer.

Saving energy and respecting the

environment

Saving water and energy

 Only begin a wash cycle when the dishwasher is full. While

waiting for the dishwasher to be filled, prevent unpleasant

odours using the Soak cycle (see Wash cycles).

 Select a wash cycle which is suited to the type of crockery

and to the soil level of the crockery using the Table of wash

cycles:

- For dishes with a normal soil level, use the Eco wash

cycle, which guarantees low energy and water

consumption levels.

- If the load is smaller than usual activate the Half load

option

* (see Start-up and use).

 If your electricity supply contract gives details of electricity

saving time bands, run wash cycles during the periods

when a lower tariff is applied. The Delayed start* button

(see Start-up and use) helps you organise the wash cycles

accordingly.

Phosphate-free and chlorine-free detergents

containing enzymes

 We strongly recommend that you use detergents that do

not contain phosphates or chlorine, as these products are

harmful to the environment.

 Enzymes provide a particularly effective action at

temperatures around 50°C, and as a result detergents

containing enzymes can be used in conjunction with low-

temperature wash cycles in order to achieve the same

results as a normal 65°C wash cycle.

 To avoid wasting detergent, use the product in appropriate

quantities based on the manufacturers recommendations,

the hardness of the water and the soil level and quantity of

crockery to be washed. Even if they are biodegradable,

detergents contain substances which may alter the balance

of nature.

Assistance

Before contacting Assistance:

 Check whether the problem can be resolved using the

Troubleshooting guide (see Troubleshooting).

 Restart the programme to check whether the problem has

ceased to exist.

 If the problem persists, contact the Authorised Technical

Assistance Service.

Never use the services of unauthorised technicians.

Please have the following information to hand:

 The type of malfunction.

 The appliance model (Mod.).

 The serial number (S/N).

This information can be found on the appliance data plate (see

Description of the appliance).

* Only available in selected models.

EN

"

Troubleshooting

Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.

Malfunction: Possible causes / Solutions:

The dishwasher does not start.

• The plug has not been inserted into the electrical socket properly, or there is

no power in the house.

• The dishwasher door has not been shut properly.

• A delayed start has been programmed (see Start-up and use).

No water drains out from the

dishwasher.

• The dishwasher cycle has not yet finished.

• The water outlet hose is bent (see Installation).

• The drain duct is blocked.

• The filter is clogged up with food residues.

The dishwasher makes

excessive noise.

• The dishes are rattling against each other or against the sprayer arms.

• An excessive amount of foam has been produced: the detergent has not

been measured out correctly or it is not suitable for use in dishwashers

(see Start-up and use).

The dishes and glasses are

covered in a white film or

limescale deposits.

• The level of the refined salt is low or the dosage setting is not suited to the

hardness of the water (see Rinse aid and salt).

• The lid on the salt dispenser is not closed properly.

• The rinse aid has been used up or the dosage is too low.

• The crockery is made from non-stick material.

The dishes and glasses are

streaked or have a bluish

tinge.

• The rinse aid dosage is too high.

The crockery has not been

dried properly.

• A wash cycle without a drying programme has been selected.

• The rinse aid has been used up or the dosage is too low (see Rinse aid and

salt).

• The rinse aid dispenser setting is not high enough.

The dishes are not clean.

• The racks are overloaded (see Loading the racks).

• The crockery has not been arranged well.

• The sprayer arms cannot move freely.

• The wash cycle is too gentle (see Wash cycles).

• An excessive amount of foam has been produced: the detergent has not

been measured out correctly or it is not suitable for use in dishwashers

(see Start-up and use).

• The lid on the rinse aid compartment has not been shut correctly.

• The filter is dirty or blocked (see Care and maintenance).

• The refined salt level is low (see Rinse aid and salt).

The dishwasher does not take

any water in/Tap shut-off

alarm.

(several short beeps are emitted)

(the ON/OFF indicator light flashes and

the number 6 appears on the display).

• There is no water in the mains supply.

• The water inlet hose is bent (see Installation).

• Turn on the tap and the appliance will start after a few minutes.

• The appliance lock has been activated because no action was taken when

the beeps sounded. Switch off the machine using the ON/OFF button, turn

on the tap and switch the machine back on after 20 seconds by pressing

the same button. Re-programme the machine and restart the wash cycle.

Water intake solenoid valve

malfunction alarm

(the ON/OFF indicator light flashes and

the number 2 appears on the display).

• Switch off the appliance by pressing the ON/OFF button and switch it back

on after one minute. If the alarm continues, shut off the water tap to

eliminate the risk of flooding, remove the plug from the electrical socket

and contact Assistance.

Water inlet hose alarm/Water inlet

filter blocked.

(the ON/OFF indicator light flashes and

the number 7 appears on the display).

• Switch off the appliance by pressing the ON/OFF button. Shut off the water

tap to eliminate the risk of flooding and remove the plug from the electrical

socket. Make sure the water inlet filter has not become blocked by various

impurities. (see “Care and maintenance” chapter).

Page is loading ...

Hotpoint lft 2294 a ha Owner's manual

Hotpoint lft 2294 a ha Owner's manual

in other languages

Related papers

Other documents