Indesit VIA 640 0 C Owner's manual

English

GB

Instructions for use

HOB

Contents

Istruzioni importanti per la sicurezza 13

Consigli per la salvaguardia dell'ambiente 14

Dichiarazione di conformità 14

Prima dell’utilizzo 14

Recipienti preesistenti 14

Diametri fondo pentola consigliati 15

Tabella potenze 15

Installazione 16

Collegamento alla rete elettrica 16

Istruzioni per l’uso 17

Operazioni di pulizia 20

Guida ricerca guasti 20

Rumorosità del piano di cottura 20

Servizio assistenza 21

Consignes de securite importantes 22

Conseils pour la protection de

l’environnement 23

Declaration de conformite 23

Avant d’utiliser l’appareil 23

Anciens recipients 23

Diamètre conseille pour le

fond

des casseroles 24

Table des puissances 24

Installation 25

Branchement électrique 25

Mode d’emploi 26

Nettoyage 28

Diagnostic des pannes 29

La table de cuisson est bruyante 29

Service apres-vente 29

Important safety instructions 5

Safeguarding the environment 6

Declaration of conformity 6

Before use 6

Existing pots and pans 6

Recommended pot bottom widths 6

Installation

7

Power level table 7

Electrical

connection 8

Instructions for use 9

Cleaning 11

Troubleshooting guide 11

Noises made by the hob 11

After-sales service 12

IT

FR

Istruzioni per l’uso

PIANO COTTURA

Sommario

Mode d’emploi

TABLE DE CUISSON

Sommaire

Français

Italiano

Instrucciones importantes

para la seguridad 30

Consejos para proteger el medio

ambiente 31

Declaración de conformidad 31

Antes del uso 31

Recipientes preexistentes 31

Diámetros recomendados

para el fondo de la olla 32

Tabla de potencias 32

instalación 33

Conexión eléctrica 33

instrucciones de uso 34

limpieza 37

Guía para la solución de problemas 37

Ruido generado por la placa

de cocción 37

Servicio de

asistencia técnica 38

ES

Manual de instrucciones

ENCIMERA

Sumario

Español

NL

LIGAÇÃO ELÉTRICA

DEKLARACJA ZGODNOŚCI

PRZED ROZPOCZĘCIEM PRACY

INSTALACJA

INSTRUKCJA WYSZUKIWANIA USTEREK

Instrukcja obsługi

PŁYTA GRZEJNA

Spis treści

Ważne instrukcje bezpieczeństwa 48

Porady dotyczące ochrony środowiska 49

Deklaracja zgodności 49

Przed rozpoczęciem pracy 49

I stniejące naczynia 50

Zalecane średnice dna naczyń 50

Tabela mocy 51

Instalacja 51

Podłączenie do zasilania 52

Instrukcja obsługi 53

Instrukcja wyszukiwania usterek 55

Czyszczenie 55

Hałas generowany przez płytę kuchenną 56

Serwis techniczny 56

PL

Polski

Důležité bezpečnostní pokyny 57

Rady k ochraně životního prostředí 58

Prohlášení o souladu s předpisy 58

Před použitím 58

Staré nádoby 58

Doporučené průměry dna nádoby 59

Instalace 60

Připojení k elektrické síti 60

Návod k použití 62 čištění 64

Jak odstranit poruchu 64

Hluk zapnuté varné desky 65

Servis 65

tabulka výkonů 59

Návod k použití

VARNÁ DESKA

Obsah

CZ

Česky

Instrucţiuni importante privind siguranţa 66

Recomandări pentru protecţia

Mediului înconjurător 67

Înainte de utilizare 67

Recipiente deja existente 67

Diametre recomandate pentru baza oalelor 68

Tabel niveluri de putere 68

Instalarea 69

Conectarea la reţeaua de alimentare

cu energie electrică 69

Instrucţiuni de utilizare 70

Curăţenie 73

Ghidul de detectare a defecţiunilor 73

Zgomot generat de plită 73

Serviciul de asistenţă tehnică 74

Românã

Instrucţiuni de folosire

ARAGAZ CUPTOR

RO

Gebruiksaanwijzing

KOOKPLAAT

Inhoud

Belangrijke veiligheidsinstructies 39

Milieutips 40

verklaring van overeenstemming 40

Vvoordat u de kookplaat in gebruik neemt 40

Rreeds aanwezige pannen 40

Aanbevolen diameter panbodem 41

Vermogenstabellen 41

Installatie 42

Elektrische aansluiting 42

Gebruiksaanwijzing 43

Reinigen 46

Opsporen van storingen 46

Geluiden afkomstig van de kookplaat 46

Klantenservice 47

Instruções para a utilização

PLANO

Índice

PT

Português

Instruções de segurança importantes

Conselhos para a protecção do ambiente

Declaração de conformidade

Antes da utilização

Recipientes pré-existentes 76

Diâmetros aconselhados do fundo das panelas

Tabela de potências

Instalação

Ligação elétrica

Instruções de utilização

Guia para resolução de avarias

Ruído gerado pela placa 82

Serviço pós-venda 83

L impeza

PT

82

79

78

77

75

76

Page is loading ...

4

Min. 40 cm

Min. 10 cm

Min. 5 cm

X 4

1

2

3

4

5 6

EN5

These instructions shall also be available on website: www.indesit.com

YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT

This manual and the appliance itself provide important safety messages, to be read and always observed.

All messages relevant to safety specify the potential risk to which they refer and indicate how to reduce the risk of injury, damage

and electric shocks due to incorrect use of the appliance. Make sure to comply with the following:

- Use protective gloves to perform all unpacking and installation operations.

- The appliance must be disconnected from the power supply before carrying out any installation operation.

- Installation and maintenance must be carried out by a specialised technician, in compliance with the manufacturer’s instructions

and the local safety regulations in force. Do not repair or replace any part of the appliance unless specifically stated in the user

manual.

- The appliance must be earthed.

- The power cable must be long enough for connecting the appliance, fitted in the cabinet, to the power supply.

- For installation to comply with the current safety regulations, an omnipolar switch with minimum contact gap of 3mm is

required.

- Do not use multi-sockets or extension cords.

- Do not pull the appliance’s power cable.

- The electrical parts must not be accessible to the user after installation.

- The appliance is designed solely for domestic use for cooking food. No other use is permitted (e.g. heating rooms). The

Manufacturer declines any liability for inappropriate use or incorrect setting of the controls.

- The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Very

young (0-3 years) and young children (3-8 years) shall be kept away unless continuously supervised.

- Children from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and

knowledge can use this appliance only if they are supervised or have been given instructions on safe appliance use and if they

understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be

made by children without supervision.

- Do not touch the appliance heating elements during and after use. Do not allow the appliance to come into contact with

cloths or other flammable materials until all the components have cooled down completely.

- Do not place flammable materials on or near the appliance.

- Overheated oils and fats catch fire easily. Pay attention when cooking food products rich in fat and oil.

- A separator panel (not supplied) must be installed in the compartment under the appliance.

- If the surface is cracked, switch off the appliance to avoid the possibility of electric shock (only for appliances with glass

surface).

- The appliance is not intended to be operated by means of an external timer or separate remote control system.

- Unattended cooking on a hob with fat or oil can be dangerous and may result in fire. NEVER try to extinguish a fire with water,

but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

Danger of fire: do not store items on the cooking surfaces.

- Do not use steam cleaners.

- Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.

- After use, switch off the hob element by its control and do not rely on the pan detector (only for induction appliances).

IMPORTANT SAFETY INSTRUCTIONS

This is the danger symbol, regarding safety, warning of potential risks to users and others.

All safety messages will be preceded by the danger symbol and the following words:

DANGER

Indicates a hazardous situation which, if not avoided, will result in serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could cause serious injury.

EN6

Disposal of packing

The packing material is 100% recyclable and marked with the recycling symbol ( ). The various parts of the packing must not be dispersed in the environment, but

disposed of in compliance with local regulations.

Disposal

This appliance is marked in conformity with European Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE).

By ensuring that this appliance is correctly disposed of, the user can help prevent potentially negative consequences for the environment and the health of people.

The symbol on the appliance or the accompanying documentation indicates that this product should not be treated as domestic waste but must be taken to an

appropriate collection point for recycling WEEE.

Energy saving tips

For optimum results, it is advisable to:

• Use pots and pans with bottom width equal to that of the cooking zone.

• Only use flat-bottomed pots and pans.

• When possible, keep pot lids on during cooking.

• Use a pressure cooker to to save even more energy and time.

• Place the pot in the middle of the cooking zone marked on the hob.

- This appliance has been designed, manufactured and marketed in conformity with the safety requirements of “Low Voltage” Directive 2006/95/EC (replacing 73/

23/EEC as amended) and protection requirements of “EMC” Directive 2004/108/EC.

- This appliance meets the eco design requirements of european regulation N. 66/2014, in conformity to the european standard EN 60350-2.

Use a magnet to check if the bottom of the pot is suitable for the induction hob: bottom of the pots and pans are unsuitable if not magnetically detectable.

- Make sure pots have a smooth bottom, otherwise they could scratch the hob. Check dishes.

- Never place hot pots or pans on the surface of the hob’s control panel. This could result in damage.

Place the pot on the required cooking zone before switching the hob on.

For good cooking results, the diameter of the base of the pot should match the size of the hotplate.

Pan size

To determine the size of the pot please measure the base of the pot (see picture) and refer to recommended pots bottom width table,

reported below, for perfect usage and correct pan detection. Each cooking zone has a minimum limit of detecting pans, which varies

depending on the material of the pan being used. You should therefore use the cooking zone that is most suitable for the diameter of

your pan.

SAFEGUARDING THE ENVIRONMENT

DECLARATION OF CONFORMITY

BEFORE USE

IMPORTANT: The cooking zones will not switch on if pots are not the right size. Only use pots bearing the symbol “INDUCTION SYSTEM” (Figure

opposite). Place the pot on the required cooking zone before switching the hob on.

Using suitable pots, the cooking zones cannot be used at temperatures below 10°C.

EXISTING POTS AND PANS

RECOMMENDED POT BOTTOM WIDTHS

Diameter (cm) Max (cm) Min (cm) Diameter (cm) Max (cm) Min (cm)

14.5 14.5 10 28 28 17

18 18 12 30 30 17

21 21 15 FLEXI/CONNEXION 39 - 18 12

24 24 15

26 26 17

NOOK

EN7

For best performance, when you use two pots simultaneously, put them according to the pictures below:

NOTE:

When making quick-cook foods that require perfect heat distribution (e.g. pancakes) on the 28 cm double cooking zone (where present), use pans no greater than

24 cm in diameter. For delicate cooking (for example, melting chocolate or butter) use the smaller diameter single zones.

After unpacking the product, check for any damage during transport. In case of problems, contact the dealer or the After-Sales Service.

For built-in dimensions and installation instruction, see the pictures in page 2.

PREPARING THE CABINET FOR FITTING

RECOMMENDED POT POSITION

POWER LEVEL TABLE

Power level Type of cooking Level use

(indicating cooking experience and habits)

Max. power

Boost Fast heating

Ideal for rapidly increasing the temperature of food to fast boiling in the case of water or rapidly heating

cooking liquids

9-7

Frying - boiling

Ideal for browning, starting to cook, frying frozen products, fast boiling

High power

Browning - slow frying - boiling

- grilling

Ideal for slow frying, maintaining a high boil, cooking and grilling (short duration, 5-10 minutes)

7-5

Browning - cooking - stewing -

slow frying - grilling

Ideal for slow frying, maintaining a low boil, cooking and grilling (medium duration, 10-20 minutes),

preheating

Medium power

Cooking - stewing -

slow frying - grilling

Ideal for stewing, maintaining a gentle boil, cooking and grilling (long duration).

4-3

Cooking - simmering -

thickening - creaming pasta

Ideal for prolonged cooking (rice, sauces, roasts, fish) with liquids (e.g. water, wine, broth, milk),

creaming pasta.

Ideal for prolonged cooking (volumes of less than a litre: rice, sauces, roasts, fish) with liquids

(e.g. water, wine, broth, milk)

Low power 2-1

Melting - defrosting -

keeping food hot -

creaming risottos

Ideal for softening butter, gently melting chocolate, thawing small products and keeping just-cooked

food hot (e.g. sauces, soups, minestrone)

Ideal for keeping just-cooked food hot, creaming risottos and keeping serving dishes warm

(with induction-suitable accessory),

OFF

Zero

power

Support surface

Hob in standby mode or off (possible end-of-cooking residual heat, indicated by “H”)

INSTALLATION

WARNING

- Install a separator panel under the hob.

- The lower part of the product must not

be accessible after installation.

- Do not fit the separator panel if an

undertop oven is installed.

• The distance between the underside of the appliance and the separator panel must respect the dimensions given in the figure.

• In order to ensure the correct operation of the product, do not obstruct the minimum required clearance between the hob and the top of the unit (min. 5 mm).

• If an undertop oven is installed, make sure the oven is equipped with a cooling system.

• Do not install the hob above a dishwasher or washing-machine, so that the electronic circuits do not come into contact with steam or moisture which could damage them.

• To remove the hob, use a screwdriver (not provided) to prise off the perimeter clips on the underside of the appliance.

6-7 cm

min. 20 mm

min. 5 mm

57

75

80

EN8

1. Remove the terminal cover (A) by unscrewing the screw and insert the cover into the hinge (B) of the terminal.

2. Plug the power cord into the clamp and connect the wires to the terminal block as shown in the wiring diagram located near the terminal.

3. Secure the power cable with the cable clamp.

4. Close the cover (C) and screw on the terminal with the screw removed.

For each connection to the network, the hob automatically checks for a few seconds.

ELECTRICAL CONNECTION

WARNING

- Disconnect the appliance from the power supply.

- Installation must be carried out by qualified personnel who know the current safety and

installation regulations.

- The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations

provided in this chapter.

- The power cable must be long enough to allow the hob to be removed from the worktop.

- Make sure the voltage specified on the dataplate located on the bottom of the appliance is the same as that of the home.

blue/grey

black/brown

yellow/green

Connection to main power

ONLY FOR BELGIUM

230V 2 phase 2N

}

black

brown

blue

blue (grey)

yellow/green

}

black

brown

yellow/green

blue

blue (grey)

}

black

brown

blue

blue (grey)

yellow/green

black

brown

yellow/green

blue

blue (grey)

ONLY FOR NL

AU and UK

EN9

Switching the hob ON/OFF

To switch the hob on, press the button for approx. 2 seconds until the cooking zone displays light up. To switch off, press the same button until the displays switch

off. All the cooking zones are deactivated.

If the hob has been in use, the residual heat indicator “H” remains lit until the cooking zones have cooled down.

If within 10 seconds of switching on, no function is selected, the hob switches off automatically.

Switching on and adjusting cooking zones

Place the pot on the cooking zone, switching the hob on, activate the required cooking zone by pressing the corresponding “+” button “0” appears on the display. It is

possible to select the required power level, from min. 0 to max. 9, or booster “P” if available. To increase the power level, push the “+” button. To decrease the power

level push the “-” button.

Deactivation of cooking zones

To switch off the cooking zone, press the corresponding “+” and “-” button for more than 3 seconds.

The cooking zone switches off and, if still hot, the letter “H” appears on the zone display.

Control panel lock

This function locks the controls to prevent accidental activation of the hob. To activate the control panel lock, switch the hob on and press the Lock function button for three seconds;

an acoustic signal and a luminous indicator near the padlock symbol signal activation. The control panel is locked except for the switching off function. To deactivate the control

lock, repeat the activation procedure. The luminous dot goes off and the hob is active again.

The presence of water, liquid spilled from pots or any objects resting on the button below the symbol can accidentally activate or deactivate the control panel lock.

Timer

The timer can be used to set the cooking time for a maximum of 99 minutes (1 hour and 39 minutes) for all the cooking zones.

Select the cooking zone to be used with the timer, press the timer (see figure) and a beep signals the function. The display shows “00” and the LED indication

comes on. The Timer value can be decreased and increased by keeping the slider function “+” and “-” buttons pressed. When the set time has elapsed, an acoustic signal

INSTRUCTIONS FOR USE

Power indicator display

Selected cooking zone indication

Cooking zone positioning

Control Panel Description

Control panel

Quick access

Slider

On/O

Control panel lock

Timer/Lock

function button

Power Management/

Cooking zone controls and corresponding display

Timer

On/O

Control panel lock

Booster/Automatic/Lock

function button

Power Management/

Cooking zone controls and corresponding display

Slider operation

Increase power level

Decrease power level

EN10

sounds and the cooking zone switches off automatically. To deactivate the timer, keep the Timer button pressed for at least 3 seconds.

To set the timer for another zone, repeat the above steps. The timer display always shows the timer for the selected zone or the shortest timer.

To modify or deactivate the timer, press the cooking zone selection button for the timer in question.

Control panel warnings

Residual heat indicator.

The hob is fitted with a residual heat indicator for each cooking zone. These indicators alert the user when cooking zones are still hot.

If the display shows , the cooking zone is still hot. If the residual heat indicator of a given cooking zone is lit, that zone can be used, for example, to keep

a dish warm or to melt butter.

When the cooking zone cools down, the display goes off.

Incorrect or missing pot indicator.

If you are using a pot that is not suitable, not correctly positioned or not of the correct dimensions for your induction hob, the message “no pot” will

appear in the display (see figure at side). In these situations it is recommended to reposition the pot on the hob surface until you find the position of

operation. If no pot is detected within 60 seconds, the hob switches off.

Fast boil function (Booster where it is available)

This function, only present on some cooking zones, makes it possible to exploit the hob’s maximum power (for example to bring water to the boil very quickly).

To activate the function, press the “+” button until “P” appears on the display. After 5 minutes’ use of the booster function, the appliance automatically sets the zone

to level 9.

“Power management” (Function where it is available)

Thanks to the “Power management” function, the user can set the maximum power the hob can reach, as required.

This setting is possible at any time and is maintained until the next change.

By setting the required maximum power, the hob automatically adjusts distribution in the various cooking zones, ensuring that this limit is never exceeded; with the

advantage of also being able to manage all the zones simultaneously, but without overload problems.

4 maximum power levels are available and showed on display: 2.5 – 4.0 – 6.0 – 7.2 kW (7.2 kW is considered as max power of cooktop)

At the time of purchase, the hob is set to maximum power

After plugging the appliance into the electrical socket, in the first 60 seconds it is possible to set the required power level by running the following points:

In case of an error when setting the power, the symbol appears in the middle and an acoustic signal sounds for about 5 seconds. In this case repeat the

configuration procedure from the beginning. If the error occurs again, contact the After-Sales Service.

During normal use, if the user tries to increase the maximum available power level when reached, the level of the zone in use flashes twice and an acoustic signal sounds.

To obtain a higher power in that zone, it is necessary to manually decrease the power level of one or more already active cooking zones.

FLEXI

This function is used in case of big pots that the single zone can not satisfied, ex, fish, big pot for meat.

In order to active the FLEXI/CONNEXTION ZONE, please press on + and - buttons simultaneously as shown in the picture below.

Special functions (If available)

Some models have special functions:

Automatic function

The function automatically sets a power level suitable for maintaining a low boil. Activate this function after bringing to the boil, pressing the corresponding zone

button first and then the button

.

Step Control panel Display

1 Press for approximately

3 seconds

2 Press the Power

Management button to

confirm the previous step

The display shows

3 Press to set the chosen level

amongst the different

options available

The light comes on together with the in-use

lights for the individual cooking zones

4 Press the Power

Management button to

confirm the previous step

The display shows the set level which flashes

for approximately 2 seconds; after which the

hob emits an acoustic signal and then turns

itself off; it is now ready for use

/

EN11

IMPORTANT: Do not use abrasive sponges or scouring pads. Their use could eventually ruin the glass.

• After each use, clean the hob (when it is cool) to remove any deposits and stains due to food residuals.

• Sugar or foods with a high sugar content damage the hob and must be immediately removed.

• Salt, sugar and sand could scratch the glass surface.

• Use a soft cloth, absorbent kitchen paper or a specific hob cleaner (follow the Manufacturer’s instructions).

• Liquid spillages on the cooking zones may make pans vibrate or move.

• Read and follow the instructions given in the section “Instructions for use”.

• Check that the electricity supply has not been shut off.

• Dry the hob thoroughly after cleaning it.

• If, when the hob is switched on, alphanumeric codes appear on the display, consult the following table for instructions.

• If the hob cannot be switched off after using it, disconnect it from the power supply.

The induction cooktops can generate a set of noise and vibration during normal operation, depending on the type of material and the processing of the food, such as

those described below:

• Noise contact: this type of vibration is due to the use of pots made of different materials superimposed.

• Sounds click at mid-lower power: this noise is produced in order to achieve the low-mid power required.

• Sounds like rhythmic click: this noise is produced when operating several areas of cooking and / or high performance.

• Hissing weak: this noise is due to the type of container used and the quantity of food contained.

• Background noise: the induction cooker is equipped with a fan aimed at cooling the electronic components and for this reason during operation and also for a

few minutes after switching off the hob you hear the noise of the fan. Increase / decrease the cooking zones activated, the background noise of the fan may

increase or decrease.

These conditions are normal and essential for the proper functioning of the induction system, they are not indication of failure or damage.

CLEANING

WARNING

- Do not use steam cleaners.

- Before cleaning, make sure the cooking zones are switched off and that the residual heat indicator (“H”)

is not displayed.

TROUBLESHOOTING GUIDE

ERROR CODE DESCRIPTION POSSIBLE CAUSES ERROR ELIMINATION

C81, C82

The control panel switches off

because of excessively high

temperatures

The internal temperature of electronic

parts is too high

Wait for the hob to cool down

before using it again.

C83

The control panel indicates the error

code hob off because of an issue on

electronic circuit

Cooktop has been supplied with over

voltage

Cooktop may be still used but call

the After-Sales Service

C85

Hob is not able to give power to

the pot

Pot is not suitable to the induction hob Use another induction pot

F02 or F04 or C84

The connection voltage is wrong or

issue to the power supply

The sensor detects a discrepancy

between the appliance voltage and

that of the mains supply

Disconnect the hob from the

mains and check the electrical

connection

F01, F05, F06, F07, F10, F12, F25, F33, F34,

F36, F37, F46, F47, F48, F49, F58, F61, F62,

F63, F72, F74, F77

Disconnect the hob from the power supply.

Wait a few seconds and plug it again.

If the problem persists, call the After-Sales Service and specify the error code

NOISES MADE BY THE HOB

5 Sec

Activation/deactivation of the acoustic signal (not available on slider version)

After switching the hob on, press and hold the “+” button and the outermost button on the right simultaneously for at least three seconds (“control panel lock”).

EN12

Product Guarantee and Repair Information

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has benefit of our manufacturer’s guarantee, which covers the

cost of breakdown repairs for twelve months from the date of purchase.

This gives you the reassurance that if, with in that time, your appliance is proven to be defective because of either workmanship or materials, we will, a tour discretion,

either repair or replace the appliance at no cost to you:

This guarantee is subject to the following conditions:

-

The appliance has been installed and operated correctly and in accordance with our operating and maintenance instructions.

-

The appliance is used only on the electricity or gas supply printed on the rating plate.

-

The appliance has been used for normal domestic purposes only.

-

The appliance has not been altered, serviced, maintained, dismantled, or

otherwise interfered with by any person not authorised by us.

-

Any repair work must be undertaken by us or our appointed agent.

-

Any parts removed during repair work or any appliance that is replaced become our

property.

-

The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

-

Damage resulting from transportation, improper use, neglect or interference or as a result of improper installation.

-

Replacement of any consumable item or accessory. These include but are not

limited to: plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers

and filters.

-

Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN

COMMERCIAL OR NON

-

DOMESTIC PREMISES.

Recycling and Disposal Information

As part of Hotpoint’s continued commitment to helping the environment,

Hotpoint reserves the right to use quality, recycled components to keep down

customer

costs and minimise material wastage.

Please dispose of packaging and old appliances carefully. To minimise the risk of

injury to children, remove the door, plug, and cut the mains cable off flush with

the

appliance. Dispose of these parts separately to ensure that the appliance can

no longer be plugged into mains socket, and the door cannot be locked shut.

Repairs and After Sales

For product help and advice, repairs, spare parts or accessories, we’re here to help.

For local repair engineers

-

03448111606

ROI

-0818313413

UK standard local rate applies

ROI local Irish rate applies

For Parts and Accessories visit:

parts.hotpoint.co.uk/shop

Please remember to register your appliance at w

ww.hotpoitservice.co.uk

to activate your 10 year parts guarantee.

Please note, our advisors will require the following information:

Model number

Serial number

Before contacting the After-sales Service:

1. See if you can solve the problem yourself with the help of the “Troubleshooting guide”.

2. Switch the appliance off and then on again it to see if the problem has been eliminated.

If the problem persists after the above checks, contact the nearest After-Sales Service.

Always specify:

• a brief description of the fault;

• the product type and exact model;

• the Service number (the number after the word Service on the rating plate), located under the appliance (on the metal plate).

• your full address;

• your telephone number.

If any repairs are required, contact an authorised After-Sales Service Centre (to ensure the use of original spare parts and correct repairs). Spare parts are available

for 10 years.

AFTER-SALES SERVICE

Page is loading ...