Black & Decker BDL300S User manual

Category
Laser levels
Type
User manual
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZADE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR ELPRODUCTO.
INSTRUCTION
MANUAL
33
33
66
66
00
00
˚˚
˚˚
AA
AA
uu
uu
tt
tt
oo
oo
LL
LL
aa
aa
ss
ss
ee
ee
rr
rr
LL
LL
ee
ee
vv
vv
ee
ee
ll
ll
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-544-6986
IF YOU SHOULD HAVE AQUESTION OR EXPERIENCE A
PROBLEM WITH YOUR BLACK &DECKER PRODUCT,
CALL 1-800-544-6986
BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE No., AND
DATE CODE (e.g. 20000130M). IN MOST CASES, ABLACK & DECKER REPRESENTATIVE CAN
RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE ASUGGESTION OR COMMENT, GIVE
US A CALL. YOUR FEEDBACK IS VITALTO BLACK & DECKER.
Catalog No.
BDL300S
586017-00 BDL300S laser 7/30/03 8:51 AM Page 1
WARNING: Read and understand all
instructions. Failure to follow all
instructions listed below may result in
electric shock, fire and/or serious personal
injury.
SAVE THESE INSTRUCTIONS
Safety Instructions
Do not operate the laser in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust.
Use the laser only with the specifically
designated batteries. Use of any other
batteries may create a risk of fire.
Store idle laser out of reach of children
and other untrained persons. Lasers are
dangerous in the hands of untrained
users.
Use only accessories that are
recommended by the manufacturer for
your model. Accessories that may be
suitable for one laser, may create a risk of
injury when used on another laser.
Do not use optical tools such as a
telescope or transit to view the laser
beam. Serious eye injury could result.
Do not place the laser in a position which
may cause anyone to intentionally or
unintentionally stare into the laser beam.
Serious eye injury could result
Turn the laser off when it is not in use.
Leaving the laser on increases the risk of
staring into the laser beam.
Repairs and servicing MUST be
performed by a qualified repair facility.
Repairs performed by unqualified
personnel could result in serious injury.
WARNING: DO NOT DISASSEMBLE
THE LASER. There are no user
serviceable parts inside. Disassembling
the Laser will void all warranties on the
product. Do not modify the product in any
way. Modifying the tool may result in
Hazardous Laser Radiation Exposure.
Do not operate the laser around children
or allow children to operate the laser.
Serious eye injury may result.
Do not remove or deface warning labels.
Removing labels increases the risk of
exposure to radiation.
Position the laser securely. Damage to the
laser or serious injury could result if the
laser falls.
CAUTION: Use caution when drilling,
nailing or cutting into walls, floors and
ceilings which may contain electrical
wiring or pipes. Always turn off the
power when working near electrical
wires.
CAUTION: Use of controls or
adjustments or performance of procedures
other than those specified in this manual
may result in hazardous laser radiation
exposure.
The label on your tool may include the
following symbols.
V................................volts
mW............................milliwatts
nm..............................wavelength in
..................................nanometers
IIIa..............................Class IIIa Laser
For your convenience and safety, the
following labels are on your laser.
2
1
2
586017-00 BDL300S laser 7/30/03 8:51 AM Page 2
3
INSTALLING THE BATTERY
Ensure laser on/off switch is in the left “OFF” position.
Remove the battery compartment cover by pressing the
tab of the cover in towards the center of the laser and out
as shown in figure 3. Connect a fresh 9 volt alkaline
battery making sure to match (+) and (-) terminals
correctly. Replace the battery compartment cover.
ASSEMBLY / SET-UP
UNFOLDING THE LASER LEGS
To open the 360° Laser:
1.) Choose a relatively smooth and level surface away
from other work site activity to position the tripod.
2.) Unfasten the strap that is around the outside portion of
the laser and unfold the three sections of the laser
housing which become the legs of the tripod.
3.) Lock the legs in place, by pushing in on the top portion
of the hinge until it snaps into place as shown in figure 4.
CAUTION: Make sure tripod is secure and sitting
on a flat and stable surface.
ADJUSTING THE TRIPOD
The tripod is adjustable from its
lowest position of approximately 27
inches (686mm) shown in figure 5 to
a maximum height of 5 feet
(1524mm) shown in figure 6.
Extend any or all of the 5 sections of the tripod to reach the
approximate desired height. Extend each section by gently sliding
each tube out until it stops and then pull slightly harder on each
section to lock.
When the approximate desired height is obtained, use the fine
adjust knob shown in figure 8 to raise the laser to the final desired
height. The fine adjustment knob will raise the laser up to an
additional 7 inches (178mm) high.
First, loosen the lock knob as shown in figure 7.
Turn the fine adjust knob (figure 8) until the desired height is
reached. Tighten the lock knob (fig. 7) to secure the tripod at the
adjusted height.
3
4
65
7
8
Lock Knob
Fine Adjust
Knob
586017-00 BDL300S laser 7/30/03 8:51 AM Page 3
4
REMOVING LASER FROM TRIPOD
The laser can be removed from the tripod for use on any
horizontal surface such as a floor or a tabletop.
CAUTION: Make sure laser is secure and on a stable
surface.
Remove the laser by pressing in on the two spring loaded
tabs shown in figure 9 and lifting the laser off the tripod.
To reattach laser to tripod, grasp the tripod top plate to
support, align notches in laser with tabs (buttons) on
plate. Press laser down until the tabs to lock into place.
Make sure laser is securely fastened.
HANGING THE LASER
The laser can also be hung
from a joist or other secure
structure using the hanging
strap included.
CAUTION: Make sure
laser is securely suspended
by the strap.
To hang, thread the strap
through the slot in the top of
the laser and fasten the hook
as shown in figures 10 and
11. Adjust the laser so that it
hangs relatively straight. The
self-leveling function will then compensate for any minor error.
LASER OPERATION
Before attempting to use the laser, make sure the tool is positioned on a relatively
smooth, flat and stable surface.
To increase working distance and accuracy, set up the laser in the middle of your working
area. Brightness of area may effect line visibility.
When attaching to the tripod or using the hanging strap, mount the laser securely.
Be aware that extreme temperature changes can cause movement or shifting of building
structures, tripods, equipment, etc. which can effect accuracy. Verify your set-up before
each use as the laser may have moved.
This product is not recommended for outdoor use.
TURNING THE LASER ON
To turn the laser on, slide the lower on/off switch shown in figure 12 to
the right.
OPERATING IN SINGLE 120˚ LASER MODE
To operate the laser using a single laser beam, slide the upper switch
to the left as shown in figure 13.
OPERATING IN 360˚ LASER MODE
To operate the laser using all 3 laser beams, slide the upper switch to
the right as shown in figure 14.
9
10
11
12
13
14
586017-00 BDL300S laser 7/30/03 8:51 AM Page 4
5
STORAGE
To store the unit, reattach the laser to the top of the tripod making sure that it snaps into
place securely. Loosen the locking knob, turn the fine adjust knob to its lowest setting and
return the tripod to its lowest position. Unhinge the legs and fold them into the center.
Reattach the strap around housing. Always store the laser indoors and in its closed state
with the switch in the “OFF” position.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual) should be performed by authorized
service centers or other qualified service personnel, always using identical replacement
parts.
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call:
1-800-54-HOW-TO (544-6986).
WARNING: The use of any accessory not recommended for use with this tool could
be hazardous.
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide
customers with efficient and reliable power tool service. Whether you need technical
advice, repair, or genuine factory replacement parts, contact the Black & Decker location
nearest you. To find your local service location, refer to the yellow page directory under
"Tools—Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in
material or workmanship. The defective product will be replaced or repaired at no charge
in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should
be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days
after the sale). Proof of purchase may be required. Please check with the retailer for their
specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may
be required. Black & Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory and on our website
www.blackanddecker.com.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state. Should you have any
questions, contact the manager of your nearest Black & Decker Service Center. This
product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
Possible Cause
Solution
Problem
TT
TT
RR
RR
OO
OO
UU
UU
BB
BB
LL
LL
EE
EE
SS
SS
HH
HH
OO
OO
OO
OO
TT
TT
II
II
NN
NN
GG
GG
• Laser does not project on
wall.
• The self leveling range
for the level line is +/- 5°.
• Position tripod ona relatively
smooth and level surface.
• Line only visible on one wall.
• Switch in 120° mode.
• Move switch t 360° mode.
• Laser beam dim.
• Weak battery.
• Replace battery
586017-00 BDL300S laser 7/30/03 8:51 AM Page 5
16
Cat No. BDL300S Form # 586017-00 AUG-03 Copyright © 2003 Black & Decker Printed in China
586017-00 BDL300S laser 7/30/03 8:52 AM Page 16
1 / 1

Black & Decker BDL300S User manual

Category
Laser levels
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document