Page is loading ...
1
9
10
11
12
13
14
2
15
16
Projector Overview
1. Mini VGA Input
2. USB Output
3. Button For Power Indication
4. Remote Control Receiver
5. LED Power Indicator
6. Mini USB
7. AV In
8. Audio Output
9. Lens
10. Lens Regulator
11. Touch Pad
Lens Power
Sound Up
Sound Down
AV/VGA
12. Power Button
13. Speeker
14. iPod dock
15. Battery
16. Stand
4
5
6
1
2
3
7
8
Accessories
f1. AV Cable
f2. Mini VGA Cable
f3. MiLi AV Cable for iPhone
f4. A/C Adapter
f5. Remote Control
f1
f2
f3
f4
f5
PWR
MENU
EXIT
UP
DOWN
OK
VOL+VOL-
UD RL
AVVGA
Charge steps:
1 Install battery (15);
3 Connect A/C adapter;
4 Start charging;
5 Charge may last 3.5 hours.
LED light From left to right
1st LED lights up power < 25% 2nd LED lights up power 25-50%
3th LED lights up power 50-75% 4th LED lights up power 75-100%
Projector Operation Procedure
Diagram 1 Diagram 2
1. Connect Power cable as diagram 1;
2. Turn on Power Button (12);
3. Play external AV program acquiescently;
4. Touch “ ” button to switch to PC program, ensuring the PC solution is
640X480;
5. Touch the Power button to turn o the projection function.
Power
This projector can use external power or battery for power supply.
Note: If both external power and battery are available, projector will select
external power as default power supply.
External power connection (See diagram 1).
Battery connection (See diagram2).
Battery Installation and Charge
1. Insert the Battery Module along the Battery slot with electrical contacts;
facing downward and thinner side facing the front;
2. Adjust Battery to ensure proper contact.
Battery Charge
Projector Applications
AV Program Playing
This projector can play external program through AV port or VGA port.
1. AV cable end (f1) connects to AV port (7);
2. AV cable end (f1) connects to AV source;
Take iPod as an example, Projector can connect with iPod through special
iPod connector (not included).
3. Supply power with adapter (f4) or Battery;
4. Turn on Power Switch. Then Turn on Projection Switch. Detailed operation
please refer to the Projector Operation Procedure;
5. Adjust volume with Volume Up/Down;
6. Adjust focus with Focus Dial.
VGA Program Playing
Remote Control User Guide
1. Power supply with A/C adapter or battery;
2. Connect the projector with VGA input source through VGA cable
connector (f2);
3. Following similar steps with AV Program Playing.
Introduction to Key Buttons
PWR: Power on, click this button once.
Power o, click this button twice.
: Press the bottom to switch into mute mode.
MENU: Use this button to enter the main menu.
This button also can be used for returning to main menu when you are in the
sub- menu.
Main menu has two submenus, which are listed as below:
DISPLAY:
Contrast
Brightness
Saturation
Tint
Color temperature
Recall (Restore system default settings)
SYSTEM:
Language (Support English and Traditional Chinese)
OSD location (Adjust the display position of menu)
Transparency (Adjust the display transparency of menu)
OSD timeout (Dene seconds of auto quit of menu without any operations)
Usage sample (Adjust transparency and OSD Location):
1. Press “MENU”;
2. Select “System” by click “Down”;
3. Press “OK”;
4. Select “OSD Location” by click “Down”;
5. Press “OK”;
6. Press “VOL” to adjust OSD display position;
7. Press “DOWN” to adjust Transparency directly;
8. Press “Menu” continuously to quit the setting or press “EXIT” to quit
setting. Alternatively it would automatically quit after 15 seconds.
TIPS: Under “DISPLAY /ADVANCE/AUDIO” menus, you can select “Reset” to
restore to the default setting easily.
UP: Select the submenu above.
DOWN: Select the submenu down.
EXIT: To quit the menu or submenus, VOL adjustment.
VOL-: Decrease system volume.
VOL+: Increase system volume.
OK: Conrm the selection or enter the next submenu.
U/D: Up/Down overturn of image.
R/L: Right/Left overturn of image.
VGA: Select VGA input as displaying source.
AV: Select AV input as displaying source, including external AV and MP4.
For external AV/VGA usage, please refer to Product Applications.
1. Please read this manual carefully before usage.
2. Please recharge the battery to its full extent before rst use.
3. Recharge for 6 continuous hours when the battery lowly laden.
4. The usage period may shorten due to spoilage from long time usage.
5. Long time of no usage of battery, please remove it from case, make sure it’s
recharged within 3 months interval.
6. Keep battery away from re, water in avoidance of explosion or short
circuits.
7. Do not hammer the battery.
Attention:
8. Use the product in environment of nice ventilation.
9. Use the product at 0~40, Humidity 20-80%,
10. Do not use the product in strong light, and magnetic environment.
11. Do not use the product in dirty, dusty environment.
12. Do not use the product for over 2 continuous hours.
13. Do not soak or drench the product.
14. Avoid eye winker into the product.
15. Do not stare to the product during playing.
16. Do not hammer, shock, throw the product and its accessory.
17. Do not throw the product and accessory in re or water.
18. Avoid infection of virus when connected to PC.
19. Please use attached accessories or designated ones.
20. Power o the product before cleaning.
21. Please be noted with the labeling.
22. Do not repair the product privately, please contact the local service
centre or dealers.
23. Please touch on the botton. Do not press forcible.
24. The projector belongs to high consumption heating product. Please
turn o the lens after 3 hours working to save energy sources and protect
lens from aging.
25. it is suggested not using under high temperature of 40 °C above.
Using under normal temperature or in-house with air-conditioning would
be the best.
26. Battery is insulated when shipping in case not working for long and
accident during transportation. Please remove the insolution ake
between battery and reed for normal use.
Conformity with FCC section 15, level B digital equipment constraint;
Conformity with EMC Directive 2004/108/EC (including amendments).
Please refer to instructions below if you encounter any of the following
problems. If such problem persists, please contact your local distributor or
service center.
No image appears on-screen:
Make sure the cables/charger/battery is correctly and securely connected;
Make sure operation is conducted following proper instructions and the
Accreditation Statements:
Troubleshooting:
projector is switched on;
Make sure the projection lens is not blocked.
Image out of focus:
Adjust the Focus Dial.
Please do not use the projector in the occasion with strong light;
Make sure the projection distance is within the recommended range of 0.2
to 3.5 meters between projection lens and screen.
Battery Problems:
Battery power is insucient;
Remove the battery and clean the metal contacts;
The battery is worn-out and needs to be replaced.
Register on website after purchasing product within 1 week is suggested.
Telephone: (+86 755) 83741500, 88351917
Fax: (+86 755) 83741501
Email: [email protected]
Web: www.iphonemili.com
Service Hours: 9 am to 6 pm
Factory Add: Building E, Dakan Science and Technology
Park, Xili Town, Nanshan District, Shenzhen, China
Shenzhen hali-power industrial co.,ltd.
Li-Pol Battery : 11.1V/1200mAh
Input: 14V 2A(max)
Output: 5V 500mA (max)
Charging time: 3 hours
Projection screen size: 5-70inches
Resolution: 640X480 pixels(VGA)
Contrast: 100 : 1
Brightness: 10 Lumens
Projection system: LCOS RGB
Projection source: 3-in-1 AV jack, VGA
Audio output: 2W built-in speaker,
Audio jack output
Lifetime of LED: 20000 hours
Battery for projector time: Up to 1.5hours
Projection source: iPhone, iPod, MP4, DVD, STB, Laptop
Dimension: 148(L)X70(D)X41(T)mm
Product Specications:
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
PWR
MENU
EXIT
UP
DOWN
OK
VOL+VOL-
UD RL
AVVGA
配件
f1.
f2. Mini VGA
f3. MiLi
f4. AC/DC
f5.
f1
f2
f3
f4
f5
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
