MiLi HI-P60-1 User manual

Page is loading ...

1

9

10

11

12

13

14

2

15

16

Projector Overview

1. Mini VGA Input

2. USB Output

3. Button For Power Indication

4. Remote Control Receiver

5. LED Power Indicator

6. Mini USB

7. AV In

8. Audio Output

9. Lens

10. Lens Regulator

11. Touch Pad

Lens Power

Sound Up

Sound Down

AV/VGA

12. Power Button

13. Speeker

14. iPod dock

15. Battery

16. Stand

4

5

6

1

2

3

7

8

Accessories

f1. AV Cable

f2. Mini VGA Cable

f3. MiLi AV Cable for iPhone

f4. A/C Adapter

f5. Remote Control

f1

f2

f3

f4

f5

PWR

MENU

EXIT

UP

DOWN

OK

VOL+VOL-

UD RL

AVVGA

Charge steps:

1 Install battery (15);

3 Connect A/C adapter;

4 Start charging;

5 Charge may last 3.5 hours.

LED light From left to right

1st LED lights up power < 25% 2nd LED lights up power 25-50%

3th LED lights up power 50-75% 4th LED lights up power 75-100%

Projector Operation Procedure

Diagram 1 Diagram 2

1. Connect Power cable as diagram 1;

2. Turn on Power Button (12);

3. Play external AV program acquiescently;

4. Touch “ ” button to switch to PC program, ensuring the PC solution is

640X480;

5. Touch the Power button to turn o the projection function.

Power

This projector can use external power or battery for power supply.

Note: If both external power and battery are available, projector will select

external power as default power supply.

External power connection (See diagram 1).

Battery connection (See diagram2).

Battery Installation and Charge

1. Insert the Battery Module along the Battery slot with electrical contacts;

facing downward and thinner side facing the front;

2. Adjust Battery to ensure proper contact.

Battery Charge

Projector Applications

AV Program Playing

This projector can play external program through AV port or VGA port.

1. AV cable end (f1) connects to AV port (7);

2. AV cable end (f1) connects to AV source;

Take iPod as an example, Projector can connect with iPod through special

iPod connector (not included).

3. Supply power with adapter (f4) or Battery;

4. Turn on Power Switch. Then Turn on Projection Switch. Detailed operation

please refer to the Projector Operation Procedure;

5. Adjust volume with Volume Up/Down;

6. Adjust focus with Focus Dial.

VGA Program Playing

Remote Control User Guide

1. Power supply with A/C adapter or battery;

2. Connect the projector with VGA input source through VGA cable

connector (f2);

3. Following similar steps with AV Program Playing.

Introduction to Key Buttons

PWR: Power on, click this button once.

Power o, click this button twice.

: Press the bottom to switch into mute mode.

MENU: Use this button to enter the main menu.

This button also can be used for returning to main menu when you are in the

sub- menu.

Main menu has two submenus, which are listed as below:

DISPLAY:

Contrast

Brightness

Saturation

Tint

Color temperature

Recall (Restore system default settings)

SYSTEM:

Language (Support English and Traditional Chinese)

OSD location (Adjust the display position of menu)

Transparency (Adjust the display transparency of menu)

OSD timeout (Dene seconds of auto quit of menu without any operations)

Usage sample (Adjust transparency and OSD Location):

1. Press “MENU”;

2. Select “System” by click “Down”;

3. Press “OK”;

4. Select “OSD Location” by click “Down”;

5. Press “OK”;

6. Press “VOL” to adjust OSD display position;

7. Press “DOWN” to adjust Transparency directly;

8. Press “Menu” continuously to quit the setting or press “EXIT” to quit

setting. Alternatively it would automatically quit after 15 seconds.

TIPS: Under “DISPLAY /ADVANCE/AUDIO” menus, you can select “Reset” to

restore to the default setting easily.

UP: Select the submenu above.

DOWN: Select the submenu down.

EXIT: To quit the menu or submenus, VOL adjustment.

VOL-: Decrease system volume.

VOL+: Increase system volume.

OK: Conrm the selection or enter the next submenu.

U/D: Up/Down overturn of image.

R/L: Right/Left overturn of image.

VGA: Select VGA input as displaying source.

AV: Select AV input as displaying source, including external AV and MP4.

For external AV/VGA usage, please refer to Product Applications.

1. Please read this manual carefully before usage.

2. Please recharge the battery to its full extent before rst use.

3. Recharge for 6 continuous hours when the battery lowly laden.

4. The usage period may shorten due to spoilage from long time usage.

5. Long time of no usage of battery, please remove it from case, make sure it’s

recharged within 3 months interval.

6. Keep battery away from re, water in avoidance of explosion or short

circuits.

7. Do not hammer the battery.

Attention:

8. Use the product in environment of nice ventilation.

9. Use the product at 0~40, Humidity 20-80%,

10. Do not use the product in strong light, and magnetic environment.

11. Do not use the product in dirty, dusty environment.

12. Do not use the product for over 2 continuous hours.

13. Do not soak or drench the product.

14. Avoid eye winker into the product.

15. Do not stare to the product during playing.

16. Do not hammer, shock, throw the product and its accessory.

17. Do not throw the product and accessory in re or water.

18. Avoid infection of virus when connected to PC.

19. Please use attached accessories or designated ones.

20. Power o the product before cleaning.

21. Please be noted with the labeling.

22. Do not repair the product privately, please contact the local service

centre or dealers.

23. Please touch on the botton. Do not press forcible.

24. The projector belongs to high consumption heating product. Please

turn o the lens after 3 hours working to save energy sources and protect

lens from aging.

25. it is suggested not using under high temperature of 40 °C above.

Using under normal temperature or in-house with air-conditioning would

be the best.

26. Battery is insulated when shipping in case not working for long and

accident during transportation. Please remove the insolution ake

between battery and reed for normal use.

Conformity with FCC section 15, level B digital equipment constraint;

Conformity with EMC Directive 2004/108/EC (including amendments).

Please refer to instructions below if you encounter any of the following

problems. If such problem persists, please contact your local distributor or

service center.

No image appears on-screen:

Make sure the cables/charger/battery is correctly and securely connected;

Make sure operation is conducted following proper instructions and the

Accreditation Statements:

Troubleshooting:

projector is switched on;

Make sure the projection lens is not blocked.

Image out of focus:

Adjust the Focus Dial.

Please do not use the projector in the occasion with strong light;

Make sure the projection distance is within the recommended range of 0.2

to 3.5 meters between projection lens and screen.

Battery Problems:

Battery power is insucient;

Remove the battery and clean the metal contacts;

The battery is worn-out and needs to be replaced.

Register on website after purchasing product within 1 week is suggested.

Telephone: (+86 755) 83741500, 88351917

Fax: (+86 755) 83741501

Email: [email protected]

Web: www.iphonemili.com

Service Hours: 9 am to 6 pm

Factory Add: Building E, Dakan Science and Technology

Park, Xili Town, Nanshan District, Shenzhen, China

Shenzhen hali-power industrial co.,ltd.

Li-Pol Battery : 11.1V/1200mAh

Input: 14V 2A(max)

Output: 5V 500mA (max)

Charging time: 3 hours

Projection screen size: 5-70inches

Resolution: 640X480 pixels(VGA)

Contrast: 100 : 1

Brightness: 10 Lumens

Projection system: LCOS RGB

Projection source: 3-in-1 AV jack, VGA

Audio output: 2W built-in speaker,

Audio jack output

Lifetime of LED: 20000 hours

Battery for projector time: Up to 1.5hours

Projection source: iPhone, iPod, MP4, DVD, STB, Laptop

Dimension: 148(L)X70(D)X41(T)mm

Product Specications:

Page is loading ...

PWR

MENU

EXIT

UP

DOWN

OK

VOL+VOL-

UD RL

AVVGA

配件

f1.

f2. Mini VGA

f3. MiLi

f4. AC/DC

f5.

f1

f2

f3

f4

f5

Page is loading ...

MiLi HI-P60-1 User manual

This manual is also suitable for

MiLi HI-P60-1 User manual

in other languages

Related papers

Other documents