Samsung SWA-8500S User manual

Category
Supplementary music equipment
Type
User manual
ENG - 2 ENG - 3
Safety Information
Thank you for purchasing this product (SWA-8500S).
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
This symbol indicates that
high voltage is present
inside. It is dangerous to
make any kind of contact
with any internal part of
this product.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Refer to the table below for an explanation of
symbols which may be on your Samsung product.
This symbol indicates that
this product has included
important literature
concerning operation and
maintenance.
Class II product : This symbol indicates that it does not require a safety connection to
electrical earth (ground). If this symbol is not present on a product with a power cord,
the product MUST have a reliable connection to protective earth (ground).
AC voltage : This symbol indicates that the rated voltage marked with the symbol is AC
voltage.
DC voltage : This symbol indicates that the rated voltage marked with the symbol is DC
voltage.
Caution, Consult instructions for use : This symbol instructs the user to consult the user
manual for further safety related information.
The slots and openings in the cabinet and
in the back or bottom are provided for
necessary ventilation. To ensure reliable
operation of this apparatus, and to protect it
from overheating, these slots and openings
must never be blocked or covered.
Do not place this apparatus in a conned
space, such as a bookcase, or built-in
cabinet, unless proper ventilation is
provided.
Do not place this apparatus near or over
a radiator or heat register, or where it is
exposed to direct sunlight.
Do not place vessels (vases etc.)
containing water on this apparatus.
A water spill can cause a re or electric
shock.
Do not expose this apparatus to rain
or place it near water (near a bathtub,
washbowl, kitchen sink, or laundry tub, in
a wet basement, or near a swimming pool,
etc.). If this apparatus accidentally gets wet,
unplug it and contact an authorized dealer
immediately.
Do not overload wall outlets, extension cords
or adaptors beyond their capacity, since this
can result in re or electric shock.
ENG - 2 ENG - 3
Safety Information
Thank you for purchasing this product (SWA-8500S).
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
This symbol indicates that
high voltage is present inside.
It is dangerous to make any
kind of contact with any
internal part of this product.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE THE
COVER (OR BACK). THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER ALL
SERVICING TO QUALIFIED PERSONNEL.
This symbol indicates that
this product has included
important literature
concerning operation and
maintenance.
Class II product : This symbol indicates that it does not require a safety connection to
electrical earth (ground).
AC voltage : This symbol indicates that the rated voltage marked with the symbol is AC
voltage.
DC voltage : This symbol indicates that the rated voltage marked with the symbol is DC
voltage.
Caution, Consult instructions for use : This symbol instructs the user to consult the user
manual for further safety related information.
Route power-supply cords so that they are
not likely to be walked on or pinched by items
placed on or against them. Pay particular
attention to cords at the plug end, at wall
outlets, and the point where they exit from
the apparatus.
To protect this apparatus from a lightning
storm, or when it is left unattended and
unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the
set due to lightning and power line surges.
Before connecting the AC power cord to the
DC adaptor outlet, make sure the voltage
designation of the DC adaptor corresponds to
the local electrical supply.
Never insert anything metallic into the open
parts of this apparatus. Doing so may create a
danger of electric shock.
To avoid electric shock, never touch the inside
of this apparatus. Only a qualied technician
should open this apparatus.
Make sure to plug the power cord in until it is
rmly seated. When unplugging the power
cord from a wall outlet, always pull on the
power cord’s plug. Never unplug by pulling on
the power cord. Do not touch the power cord
with wet hands.
If this apparatus does not operate normally
- in particular, if there are any unusual
sounds or smells coming from it - unplug it
immediately and contact an authorized dealer
or service centre.
Maintenance of Cabinet.
Before connecting other components to
this product, be sure to turn them off.
Be sure to pull the power plug out of the
outlet if the product is to remain unused or
if you are leaving the house for an extended
period of time (especially when children,
elderly, or disabled people will be left alone in
the house).
Accumulated dust can cause an electric
shock, an electric leakage, or a re by
causing the power cord to generate sparks
and heat or the insulation to deteriorate.
Contact an authorized service centre for
information if you intend to install your
product in a location with heavy dust, high or
low temperatures, high humidity, chemical
substances, or where it will operate 24 hours
a day such as in an airport, a train station, etc.
Failing to do so may cause serious damage to
your product.
Use only a properly grounded plug and wall
outlet.
An improper ground may cause electric
shock or equipment damage. (Class l
Equipment only.)
To turn this apparatus off completely, you
must disconnect it from the wall outlet.
Consequently, the wall outlet and power plug
must be readily accessible at all times.
Do not allow children to hang on the product.
Store the accessories (battery, etc.) in a
location safely out of the reach of children.
Do not place vessels (vases etc.)
containing water on this apparatus.
A water spill can cause a re or electric
shock.
Do not expose this apparatus to rain
or place it near water (near a bathtub,
washbowl, kitchen sink, or laundry tub, in
a wet basement, or near a swimming pool,
etc.). If this apparatus accidentally gets wet,
unplug it and contact an authorized dealer
immediately.
Do not overload wall outlets, extension cords
or adaptors beyond their capacity, since this
can result in re or electric shock.
ENG - 4 ENG - 5
Do not install the product in an unstable
location such as a shaky self, a slanted oor,
or a location exposed to vibration.
Do not drop or strike the product. If the
product is damaged, disconnect the power
cord and contact a service centre.
To clean this apparatus, unplug the power
cord from the wall outlet, and then wipe
the product using a soft, dry cloth. Do not
use any chemicals such as wax, benzene,
alcohol, thinners, insecticide, air fresheners,
lubricants, or detergent. These chemicals can
damage the appearance of the product or
erase the printing on the product.
Do not expose this apparatus to dripping
or splashing. Do not put objects lled with
liquids, such as vases, on the apparatus.
Do not plug multiple electric devices into the
same wall socket. Overloading a socket can
cause it to overheat, resulting in a re.
WARNING :
TO PREVENT THE SPREAD OF
FIRE, KEEP CANDLES AND
OTHER ITEMS WITH OPEN
FLAMES AWAY FROM THIS
PRODUCT AT ALL TIMES.
To reduce the risk of re or electric shock, do
not expose this appliance to rain or moisture.
Precautions
1. Ensure that the AC or DC power supply
in your house complies with the power
requirements listed on the identication
sticker located on the back of your product.
Install your product horizontally, on a
suitable base (furniture), with enough space
around it for ventilation (7~10 cm).
Make sure the ventilation slots are not
covered. Do not place the unit on ampliers
or other equipment which may become hot.
This unit is designed for continuous use.
To fully turn off the unit, disconnect the AC
plug from the wall outlet.
2. Do not expose the unit to direct sunlight
or other heat sources. This could lead
to overheating and cause the unit to
malfunction.
3. Unplug the Power cord from the AC wall
socket if the unit malfunctions. Your product
is not intended for industrial use. It is for
personal use only. Condensation may occur
if your product has been stored in cold
temperatures. If transporting the unit during
the winter, wait approximately 2 hours until
the unit has reached room temperature
before using it.
4. If the electricity supplied to your home is
rated at 240V AC, use a suitable plug adapter
to connect this unit to your electrical outlets.
Important Safety Instructions
Read these operating instructions carefully
before using the unit. Follow all the safety
instructions listed below. Keep these operating
instructions handy for future reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install
in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including AV receivers) that
produce heat.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug.
A polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third prong
are provided for your safety. If the provided
plug does not t into your outlet, consult an
electrician for replacement of the obsolete
outlet.
ENG - 4 ENG - 5
Precautions
1. Ensure that the AC or DC power supply
in your house complies with the power
requirements listed on the identication
sticker located on the back of your product.
Install your product horizontally, on a
suitable base (furniture), with enough space
around it for ventilation (7~10 cm).
Make sure the ventilation slots are not
covered. Do not place the unit on ampliers
or other equipment which may become hot.
This unit is designed for continuous use.
To fully turn off the unit, disconnect the AC
plug from the wall outlet.
2. Do not expose the unit to direct sunlight
or other heat sources. This could lead
to overheating and cause the unit to
malfunction.
3. Unplug the Power cord from the AC wall
socket if the unit malfunctions. Your product
is not intended for industrial use. It is for
personal use only. Condensation may occur
if your product has been stored in cold
temperatures. If transporting the unit during
the winter, wait approximately 2 hours until
the unit has reached room temperature
before using it.
4. If the electricity supplied to your home is
rated at 240V AC, use a suitable plug adapter
to connect this unit to your electrical outlets.
Important Safety Instructions
Read these operating instructions carefully
before using the unit. Follow all the safety
instructions listed below. Keep these operating
instructions handy for future reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install
in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including AV receivers) that
produce heat.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug.
A polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third prong
are provided for your safety. If the provided
plug does not t into your outlet, consult an
electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where it exits the apparatus.
11. Only use attachments/accessories specied
by the manufacturer.
12. Use only with the cart,
stand, tripod, bracket,
or table specied by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when moving the cart/
apparatus combination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning
storms or when you intend to leave it unused
for long periods of time.
14. Refer all servicing to qualied service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as when the power-supply cord or plug
is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
ENG - 6 ENG - 7
Accessories
STANDBY
LINK
Surround Speaker (2EA) Power Cord
Wireless Receiver Module Speaker Cable (2EA)
Specications
Weight
Wireless Receiver Module 0.7 kg
Surround Speaker 0.5 kg
Dimensions (W x H x D)
Wireless Receiver Module 50.0 X 201.3 X 132.0 mm
Surround Speaker 76.2 X 126.9 X 76.2 mm
Operating Temperature Range +5°C to +35°C
Operating Humidity Range 10% ~ 75%
Frequency range 20Hz~20KHz
Overall Standby Power Consumption (W) 1.0W
NOTES
Samsung Electronics Co., Ltd reserves the right to change the specications without notice.
Weight and dimensions are approximate.
For more information about the power supply and power consumption, refer to the label attached
to the product.
Design and specications are subject to change without prior notice.
Open Source Licence Notice
To send inquiries and requests regarding open sources, contact Samsung via Email
(oss.request@samsung.com).
Important Note About Service
An administration fee may be charged if either
(a) an engineer is called out at your request and there is no defect with the product (i.e. where the
user manual has not been read).
(b) you bring the unit to a repair centre and there is no defect with the product (i.e. where the user
manual has not been read).
You will be informed of the administration fee amount before a technician visits.
Connecting the SWA-8500S to a Soundbar
1. Connect the Wireless Receiver Module to 2 Surround Speakers
Use the speaker cables to connect the two surround sound speakers to the Wireless Receiver
Module.
The speaker cables are colour coded.
SURROUND-LEFT
ID SET
L
R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
POWER
ID SET
L
R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
SURROUND-RIGHT
SURROUND-LEFT SURROUND-RIGHT
When connecting the speaker cables to the Wireless Receiver Module, follow these steps:
1. Insert the grey plug into the grey jack on the Wireless Receiver.
2. Insert the blue plug into the blue jack on the Wireless Receiver.
When connecting the speaker cables to the surround speakers, follow these steps:
1. Match the speaker cable connected to the grey jack to the speaker with the grey label.
2. Match the speaker cable connected to the blue jack to the speaker with the blue label.
3. Insert the red and black coloured ends of each speaker cable into the red and black jacks of
the appropriate speakers.
The labels are on the backs of the speaker.
ENG - 6 ENG - 7
Accessories
STANDBY
LINK
Surround Speaker (2EA) Power Cord
Wireless Receiver Module Speaker Cable (2EA)
Specications
Weight
Wireless Receiver Module 0.7 kg
Surround Speaker 0.5 kg
Dimensions (W x H x D)
Wireless Receiver Module 50.0 X 201.3 X 132.0 mm
Surround Speaker 76.2 X 126.9 X 76.2 mm
Operating Temperature Range +5°C to +35°C
Operating Humidity Range 10% ~ 75%
Frequency range 20Hz~20KHz
Overall Standby Power Consumption (W) 1.0W
NOTES
Samsung Electronics Co., Ltd reserves the right to change the specications without notice.
Weight and dimensions are approximate.
For more information about the power supply and power consumption, refer to the label attached
to the product.
Design and specications are subject to change without prior notice.
Open Source Licence Notice
To send inquiries and requests regarding open sources, contact Samsung via Email
(oss.request@samsung.com).
Important Note About Service
An administration fee may be charged if either
(a) an engineer is called out at your request and there is no defect with the product (i.e. where the
user manual has not been read).
(b) you bring the unit to a repair centre and there is no defect with the product (i.e. where the user
manual has not been read).
You will be informed of the administration fee amount before a technician visits.
Connecting the SWA-8500S to a Soundbar
1. Connect the Wireless Receiver Module to 2 Surround Speakers
Use the speaker cables to connect the two surround sound speakers to the Wireless Receiver
Module.
The speaker cables are colour coded.
SURROUND-LEFT
ID SET
L
R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
POWER
ID SET
L
R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
SURROUND-RIGHT
SURROUND-LEFT SURROUND-RIGHT
When connecting the speaker cables to the Wireless Receiver Module, follow these steps:
1. Insert the grey plug into the grey jack on the Wireless Receiver.
2. Insert the blue plug into the blue jack on the Wireless Receiver.
When connecting the speaker cables to the surround speakers, follow these steps:
1. Match the speaker cable connected to the grey jack to the speaker with the grey label.
2. Match the speaker cable connected to the blue jack to the speaker with the blue label.
3. Insert the red and black coloured ends of each speaker cable into the red and black jacks of
the appropriate speakers.
The labels are on the backs of the speaker.
ENG - 8 ENG - 9
2. Check the standby status after plugging into an electrical outlet
Plug the Wireless Receiver Module power cord into an electrical outlet and into the Wireless
Receiver Module to turn on the Wireless Receiver Module. The LINK LED indicator (blue LED) on the
Wireless Receiver Module blinks. If the LED does not blink, refer to step 7 on page 10.
ID SET
L
R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE :
POWER
POWER
STANDBY
LINK
STANDBY
LINK
Blue blinking
3. Turn off the Soundbar
Turn off the Soundbar using the Soundbar’s remote control or by pressing the (Power) button
on the main Soundbar unit.
OFF
The image of the Soundbar may differ from your Soundbar, depending on the model.
4. Congure ID SETusing the Soundbar’s remote control
Press the VOL button on your remote control for 5~6 seconds until the “ID SET” message appears
on your Soundbar display.
Steps for “ID SET” may vary by the Soundbar model. Please read manual for your Soundbar.
If the manual does not provide “ID SET” instructions, follow steps described in the image below.
VOL
SOUNDBAR
ID SET
5 Sec
The image of the Soundbar may differ from your Soundbar, depending on the model.
5. Turn on the Soundbar
Turn on the Soundbar using the Soundbar’s remote control or by pressing the (Power) button on
the main Soundbar’s unit.
Some Soundbar models will be automatically powered on after completing “4. ID SET” step.
ON
The image of the Soundbar may differ from your Soundbar, depending on the model.
6. Check if the LINK LED is solid blue (connection complete)
STANDBY
LINK
Blue is On
The LINK LED indicator stops blinking
and glows a solid blue when a
connection is established between the
Soundbar and the Wireless Receiver
Module.
ENG - 8 ENG - 9
2. Check the standby status after plugging into an electrical outlet
Plug the Wireless Receiver Module power cord into an electrical outlet and into the Wireless
Receiver Module to turn on the Wireless Receiver Module. The LINK LED indicator (blue LED) on the
Wireless Receiver Module blinks. If the LED does not blink, refer to step 7 on page 10.
ID SET
L
R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE :
POWER
POWER
STANDBY
LINK
STANDBY
LINK
Blue blinking
3. Turn off the Soundbar
Turn off the Soundbar using the Soundbar’s remote control or by pressing the (Power) button
on the main Soundbar unit.
OFF
The image of the Soundbar may differ from your Soundbar, depending on the model.
4. Congure ID SETusing the Soundbar’s remote control
Press the VOL button on your remote control for 5~6 seconds until the “ID SET” message appears
on your Soundbar display.
Steps for “ID SET” may vary by the Soundbar model. Please read manual for your Soundbar.
If the manual does not provide “ID SET” instructions, follow steps described in the image below.
VOL
SOUNDBAR
ID SET
5 Sec
The image of the Soundbar may differ from your Soundbar, depending on the model.
5. Turn on the Soundbar
Turn on the Soundbar using the Soundbar’s remote control or by pressing the (Power) button on
the main Soundbar’s unit.
Some Soundbar models will be automatically powered on after completing “4. ID SET” step.
ON
The image of the Soundbar may differ from your Soundbar, depending on the model.
6. Check if the LINK LED is solid blue (connection complete)
STANDBY
LINK
STANDBY
LINK
Blue is On
The LINK LED indicator stops blinking
and glows a solid blue when a
connection is established between the
Soundbar and the Wireless Receiver
Module.
ENG - 10 ENG - 11
7. If the SWA-8500S does not connect, take the necessary steps
according to the LED Indicator’s status
LED status Action
LINK (Blue)
On
Connected with
the Soundbar
-
Blinking
Connection
standby status
Check if the Soundbar is turned on
Repeat steps 3 through 6.
STANDBY (Red) On Connection failure
Check if the Soundbar is turned on
1. Press the ID SET button on the back
of the Wireless Receiver Module with
a pen tip for 5~6 seconds until the
LINK LED indicator blinks (in Blue).
ID SET
L
R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE :
POWER
ID SET
5 Sec
2. Repeat steps 3 through 6.
Others - Errors Contact a Samsung Service Centre.
Compatible Models
Compatible with select Samsung Soundbar. Please visit the Soundbar product page at
www.samsung.com/support for more information.
Compatible model list is subject to change without further notice.
Hereby, Samsung Electronics, declares that this equipment is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address: http://www.samsung.com go to Support > Search Product Support and enter
the model name. This equipment may be operated in all EU countries.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic
accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste
at the end of their working life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate these items from other types of waste and recycle
them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government ofce, for details of where and how they can take these items for environmentally safe
recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product and its electronic accessories should not be mixed with other commercial
wastes for disposal.
For information on Samsung’s environmental commitments and product specic regulatory obligations e.g.
REACH, WEEE, Batteries, visit:
http://www.samsung.com/uk/aboutsamsung/samsungelectronics/corporatecitizenship/data_corner.html
ENG - 10 ENG - 11
7. If the SWA-8500S does not connect, take the necessary steps
according to the LED Indicator’s status
LED status Action
LINK (Blue)
On
Connected with
the Soundbar
-
Blinking
Connection
standby status
Check if the Soundbar is turned on
Repeat steps 3 through 6.
STANDBY (Red) On Connection failure
Check if the Soundbar is turned on
1. Press the ID SET button on the back
of the Wireless Receiver Module with
a pen tip for 5~6 seconds until the
LINK LED indicator blinks (in Blue).
ID SET
L
R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE :
POWER
ID SET
5 Sec
2. Repeat steps 3 through 6.
Others - Errors Contact a Samsung Service Centre.
Compatible Models
Compatible with select Samsung Soundbar. Please visit the Soundbar product page at
www.samsung.com/support for more information.
Compatible model list is subject to change without further notice.
Hereby, Samsung Electronics, declares that this equipment is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address: http://www.samsung.com go to Support > Search Product Support and enter
the model name. This equipment may be operated in all EU countries.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic
accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste
at the end of their working life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate these items from other types of waste and recycle
them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government ofce, for details of where and how they can take these items for environmentally safe
recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product and its electronic accessories should not be mixed with other commercial
wastes for disposal.
For information on Samsung’s environmental commitments and product specic regulatory obligations e.g.
REACH, WEEE, Batteries, visit:
http://www.samsung.com/uk/aboutsamsung/samsungelectronics/corporatecitizenship/data_corner.html
© 2017 Samsung Electronics Co., Ltd. All rights reserved.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer
care Centre.
Area Contact Centre
Web Site
`
Europe
UK 0333 000 0333
www.samsung.com/uk/
support
IRELAND (EIRE) 0818 717100
www.samsung.com/ie/
support
GERMANY 06196 77 555 77
www.samsung.com/de/
support
FRANCE 01 48 63 00 00
www.samsung.com/fr/
support
ITALIA 800-SAMSUNG (800.7267864)
www.samsung.com/it/
support
SPAIN 91 175 00 15
www.samsung.com/es/
support
PORTUGAL 808 207 267
www.samsung.com/pt/
support
LUXEMBURG 261 03 710
www.samsung.com/be_
fr/support
NETHERLANDS 088 90 90 100
www.samsung.com/nl/
support
BELGIUM 02-201-24-18
www.samsung.com/be/
support (Dutch)
www.samsung.com/
be_fr/support (French)
NORWAY 21629099
www.samsung.com/no/
support
DENMARK 707 019 70
www.samsung.com/dk/
support
FINLAND 030-6227 515
www.samsung.com/fi /
support
SWEDEN 0771 726 786
www.samsung.com/se/
support
POLAND
801-172-678* lub +48 22 607-93-33*
Specjalistyczna infolinia do obsługi
zapytań dotyczących telefonów
komórkowych: 801-672-678*
* (opłata według taryfy operatora)
http://www.samsung.com/
pl/support/
HUNGARY 0680SAMSUNG (0680-726-7864)
www.samsung.com/hu/
support
AUSTRIA 0800 72 67 864 (0800-SAMSUNG)
www.samsung.com/at/
support
SWITZERLAND 0800 726 786
www.samsung.com/ch/
support (German)
www.samsung.com/
ch_fr/support (French)
Area Contact Centre
Web Site
CZECH 800 - SAMSUNG (800-726786)
www.samsung.com/cz/
support
SLOVAKIA 0800 - SAMSUNG (0800-726 786)
www.samsung.com/sk/
support
CROATIA 072 726 786
www.samsung.com/hr/
support
BOSNIA 055 233 999
www.samsung.com/
support
NORTH
MACEDONIA
023 207 777
www.samsung.com/mk/
support
MONTENEGRO 020 405 888
www.samsung.com/
support
SLOVENIA 080 697 267 (brezplačna številka)
www.samsung.com/si/
support
SERBIA 011 321 6899
www.samsung.com/rs/
support
KOSOVO 0800 10 10 1
www.samsung.com/
support
ALBANIA 045 620 202
www.samsung.com/al/
support
BULGARIA
*3000 Цена на един градски разговор
0800 111 31 Безплатен за всички
оператори
www.samsung.com/bg/
support
ROMANIA
*8000 (apel in retea)
08008-726-78-64 (08008-SAMSUNG)
Apel GRATUIT
Ateie: Dacă efectui apelul din
reţeaua Digi (RCS/RDS), vă rugăm să
ne contactaţi fornd numărul
Telverde fără ultimele două cifre,
astfel: 0800872678.
www.samsung.com/ro/
support
CYPRUS
8009 4000 only from landline, toll
free
www.samsung.com/gr/
support
GREECE
80111-SAMSUNG (80111 726 7864) only
from land line
(+30) 210 6897691 from mobile and
land line
LITHUANIA 8-800-77777
www.samsung.com/lt/
support
LATVIA 8000-7267
www.samsung.com/lv/
support
ESTONIA 800-7267
www.samsung.com/ee/
support
AH68-02993F-04
AH68-02993F-04
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Samsung SWA-8500S User manual

Category
Supplementary music equipment
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI