Craftsman 917299061 Owner's manual

Brand: Craftsman

Model: 917299061

Category: Mini tillers

Type: Owner's manual

This manual is also suitable for

917.299061

Owner's Manual

CRRFT$14RH°

TI ETLL

COU TE ROTATI

900 Series

14 Inch Tine Width

Model No.

917.299061

• EspaSol, p. 22

This product has a low emission engine which operates

differently from previously built engines. Before you start the

engine, read and understand this Owner's Manual.

IMPORTANT:

Read and follow all Safety

Rules and Instructions before

operating this equipment.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Visit our Craftsman website:www.sears.com/craftsman

U.S.A.

428425 Rev. 1

Safety Rules .......................................... 2

Warranty ................................................ 2

Product Specifications ......................... 4

Assembly/Pre-Operation ....................... 6

Operation ............................................... 8

Maintenance ........................................ 13

Service and Adjustments ..................... 15

Storage ................................................ 19

Troubleshooting ................................... 20

Illustrated Parts List ............................. 42

Sears Service ........................ Back Cover

LIMITED ONE YEAR WARRANTY ON CRAFTSMAN TILLER

For one (1) year from date of purchase, when this Craftsman Tiller is maintained,

lubricated, and tuned up according to the operating and maintenance instructions in the

owner's manual, Sears will repair free of charge any defect in material or workmanship.

This Warranty does not cover:

• Expendable items which become worn during normal use, such as tines, spark plugs,

air cleaners and belts.

• Repairs necessary because of operator abuse or negligence, including bent crank-

shafts and the failure to maintain the equipment according to the instructions con-

tained in the owner's manual.

• If this Craftsman Tiller is used for commercial or rental purposes, this Warranty ap-

plies for only thirty (30) days from the date of purchase.

Warranty service is available by returning the craftsman power mower to the nearest

sears service center/department in the united states. This warranty applies only while

this product is in use in the united states.

This Warranty gives you specific legal rights, and you may also have other rights which

vary from state to state.

SEARS, ROEBUCKAND CO., D/817WA, HOFFMAN ESTATES, IL 60179 U.S.A.

IMPORTANT: This cutting machine is capable of amputating hands and feet and throw-

ing objects. Failure to observe the following safety instructions could result in serious

injury or death.

TRAINING

• Read the Owner's Manual carefully. Be

thoroughly familiar with the controls and

the proper use of the equipment. Know

how to stop the unit and disengage the

controls quickly.

• Never allow children to operate the

equipment. Never allow adults to op-

erate the equipment without proper

instruction.

• Keep the area of operation clear of all

persons, particularly small children, and

pets.

PREPARATION

• Thoroughly inspect the area where the

equipment is to be used and remove all

foreign objects.

• Disengage all clutches and shift into

neutral before starting the engine (mo-

tor).

• Do not operate the equipment without

wearing adequate outer garments. Wear

footwear that will improve footing on

slippery surfaces.

• Handle fuel with care; it is highly flam-

mable.

• Use an approved fuel container.

• Never add fuel to a running engine or

hot engine.

• Fill fue! tank outdoors with extreme

care. Never fill fuel tank indoors.

• Replace gasoline cap securely and

clean up spilled fuel before restarting.

• Use extension cords and receptacles

as specified by the manufacturer for all

units with electric drive motors or elec-

tric starting motors.

• Never attempt to make any adjustments

while the engine (motor) is running (ex-

cept where specifically recommended

by manufacturer).

OPERATION

• Do not put hands or feet near or under

rotating parts.

• Exercise extreme caution when operat-

ing on or crossing gravel drives, walks,

or roads. Stay alert for hidden hazards

or traffic. Do not carry passengers.

• After striking a foreign object, stop the

engine (motor), remove the wire from

the spark plug, thoroughly inspect the

tiller for any damage, and repair the

damage before restarting and operating

the tiller.

• Exercise caution to avoid slipping orfalling.

• If the unit should start to vibrate ab-

normally, stop the engine (motor) and

check immediately for the cause. Vibra-

tion is generally a warning of trouble.

• Stop the engine (motor) when leaving

the operating position.

• Take all possible precautions when

leaving the machine unattended. Dis-

engage the tines, shift into neutral, and

stop the engine.

• Before cleaning, repairing, or inspecting,

shut off the engine and make certain all

moving parts have stopped. Disconnect

the spark plug wire, and keep the wire

away from the plug to prevent acci-

dental starting. Disconnect the cord on

electric motors.

• Do not run the engine indoors; exhaust

fumes are dangerous.

• Never operate the tiller without proper

guards, plates, or other safety protective

devices in place.

• Keep children and pets away.

• Do not overload the machine capacity

by attempting to till too deep at too fast

a rate.

• Never operate the machine at high

speeds on slippery surfaces. Look be-

hind and use care when backing.

• Never allow bystanders near the unit.

• Use only attachments and accessories

approved by the manufacturer of the

tiller.

• Never operate the tiller without good

visibility or light.

• Be careful when tilling in hard ground.

The tines may catch in the ground and

propel the tiller forward. If this occurs,

let go of the handlebars and do not

restrain the machine.

MAINTENANCE AND STORAGE

• Keep machine, attachments, and acces-

sories in safe working condition.

• Check shear pins, engine mounting

bolts, and other bolts at frequent inter-

vals for proper tightness to be sure the

equipment is in safe working condition.

• Never store the machine with fuel in the

fuel tank inside a building where ignition

sources are present, such as hot water

and space heaters, clothes dryers, and

the like. Allow the engine to cool before

storing in any enclosure.

• Always refer to the operator's guide in-

structions for important details if the tiller

is to be stored for an extended period.

_i_Look for this symbol to point out

important safety precautions. It means

CAUTION!!! BECOME ALERT!!! YOUR

SAFETY IS INVOLVED.

_:_,CAUTION: Always disconnect spark

plug wire and place wire where it cannot

contact spark plug in order to prevent acci-

dental starting when setting up, transport-

ing, adjusting or making repairs.

_,WARNING: Engine exhaust, some of

its constituents, and certain vehicle com-

ponents contain or emit chemicals known

to the State of California to cause cancer

and birth defects or other reproductive

harm.

PRODUCT SPECIFICATIONS

Gasoline Capacity: 3 Quarts (2.8L)

Unleaded Regular

Oil (API-SG-SL): SAE 30 (Above 32°F)

(Capacity:20oz./0.6L) SAE 5W-30 (Below 32°F)

Spark Plug: NGK-BPR6ES

(Gap: .030"/0.76mm) TORCH-F6RTC

CONGRATULATIONS on your purchase

of a Sears Tiller. It has been designed,

engineered and manufactured to give you

the best possible dependability and per-

formance.

Should you experience any problems you

cannot easily remedy, please contact a

Sears or other qualified Service Center.

We have competent, well-trained techni-

cians and the proper tools to service or

repair this unit.

Please read and retain this manual. The

instructions will enable you to assemble

and maintain your tiller properly. Always

observe the "SAFETY RULES".

Your new tiller has been assembled at the

factory with exception of those parts left

unassembled for shipping purposes. To

ensure safe and proper operation of your

tiller all parts and hardware you assemble

must be tightened securely. Use the cor-

rect tools as necessary to insure proper

tightness.

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in maintain-

ing, caring for and using your tiller.

• Follow the instructions under the "Main-

tenance" and "Storage" sections of this

Owner's Manual.

_L,WARNING: This unit is equipped with

an internal combustion engine and should

not be used on or near any unimproved

forest-covered, brush-covered or grass

covered land unless the engine's exhaust

system is equipped with a spark arrester

meeting applicable local or state laws (if

any). If a spark arrester is used, it should

be maintained in effective working order

by the operator.

In the state of California the above is

required by law (Section 4442 of the

California Public Resources Code). Other

states may have similar laws. Federal

laws apply on federal lands. A spark at-

rester for the muffler is available through

your nearest Sears service center (See

REPAIR PARTS section of this manual).

REPAIR PROTECTION

AGREEMENTS

Congratulations on making a smart pur-

chase. Your new Craftsman@ product is

designed and manufactured for years of

dependable operation. But like all products,

it may require repair from time to time. That's

when having a Repair Protection Agreement

can save you money and aggravation.

Purchase a Repair Protection Agreement

now and protect yourseff from unexpected

hassle and expense.

Here's what's included in the Agreement:

• Expert service by our 12,000 profe-

sional repair specialists.

• Unlimited service and no charge for

parts and labor on all covered repairs.

• Product replacement if your covered

product can't be fixed.

• Discount of 10% from regular price of

service and service-related parts not

covered by the agreement; also, 10%

off regular price of preventive mainte-

nance check.

• Fast help by phone- phone support

from a Sears technician on products

requiring in-home repair, plus conve-

nient repair scheduling.

Once you purchase the Agreement, a

simple phone call is all that it takes for you

to schedule service. You can call anytime

day or night, or schedule a service ap-

pointment online.

Sears has over 12,000 professional repair

specialists, who have access to over 4.5

million quality parts and accessories.

That's the kind of professionalism you can

count on to help prolong the life of your

new purchase for years to come. Pur-

chase your Repair Protection Agreement

today!

Some limitations and exclusions apply.

For prices and additional information

call 1-800=827=6655.

SEARS INSTALLATION SERVICE

For Sears professional installation of

home appliances, garage door openers,

water heaters, and other major home

items, in the U.S.A. call 1-800=4-MY-

HOME@

These accessories were available when the tiller was produced. They are also available

at most Sears retail outlets and service centers. Some of these accessories may not

apply to your tiller.

ENGINE

SPARK PLUG MUFFLER AiR FILTER GAS CAN ENGINE OiL STABiLiZER

TILLER PERFORMANCE

FURROW OPENER

TILLER MAINTENANCE

BELT

SHEAR PiN

HAiRPiN CLiP

CONTENTS OF HARDWARE PACK

(2) Handle Locks

(1) Hairpin Clip

(2) Shear Pins & Clips

(1) Carriage Bolt

3/8-16 UNC x 1 Gr. 5

(1) Center Locknut

3/8-16 UNC

(1) Cable Clip

(1) Pivot Bolt

3/8-16 UNC Grade 5

(1) Flat Washer

13/32xlx11Ga.

(1) Handle Lock Lever

Your new tiller has been assembled at the factory with the exception of those parts left

unassembled for shipping purposes. To ensure safe and proper operation of your tiller

all parts and hardware you assemble must be tightened securely. Use the correct tools

as necessary to insure proper tightness.

TOOLS REQUIRED FOR

ASSEMBLY

A socket wrench set will make assembly

easier. Standard wrench sizes are listed.

(1) Utility knife

(1) Wire cutter

(1) Tire pressure gauge

(1) Screwdriver

(1) Pair of pliers

(1) 9/16" wrench

OPERATOR'S POSITION

When right or left hand is mentioned in

this manual, it means when you are in the

operating position (standing behind tiller

handles).

FRONT

LEFT

RIGHT

4. Cut down right hand front and right

hand rear corners of carton, lay side

carton wall down.

5. Remove packing material from handle

assembly.

6. Separate shift rod from handle assem-

bly.

Shift Rod

Handle

Assembly

INSTALL HANDLE

Insert one handle lock (with teeth fac-

ing outward) in gearcase notch. (Apply

grease on smooth side of handle lock

to aid in keeping lock in place until

handle assembly is lowered into posi-

tion.)

VIEWED FROM R.H. SIDE OF TILLER

OPERATOR'S

POSITION

UNPACKING CARTON

,4_kCAUTION: Be careful of exposed sta-

ples when handling or disposing of carton-

ing material.

IMPORTANT: When unpacking and

assembling tiller, be careful of exposed

staples when handling or disposing of

cartoning material.

1. While holding handle assembly, cut cable

ties securing handle assembly to top

frame. Let handle assembly rest on tiller.

2. Remove top frame of carton.

3. Slowly ease handle assembly up and

place on top of carton.

_,. GeHandle Assembly

arcase Notch

Handle Lock

2. Grasp handle assembly. Hold in "up"

position. Be sure handle lock remains

in gearcase notch. Slide handle as-

sembly into position.

3. Rotate handle assembly down. Insert

rear carriage bolt first, with head of

bolt on LH. side of tiller and loosely

assemble Iocknut.

Loosen Handle Lock

Lever to Move

4. Insert pivot bolt in front part of plate

and tighten.

5. Cut down remaining corners of carton

and lay panels flat.

6. Lower the handle assembly. Tighten

nut on carriage bolt so handle moves

with some resistance. This will allow

for easier adjustment.

7. Place flat washer on threaded end of

handle lock lever.

8. Insert handle lock lever through handle

base and gearcase. Screw in handle

lock lever just enough to hold lever in

place.

9. Insert second handle lock (with teeth

inward) in the slot of the handle base

(just inside of washer).

10. Raise handle assembly to highest po-

sition and securely tighten handle lock

lever by rotating clockwise. Leaving

handle assembly in highest position

will make it easier to connect shift rod.

Flat Washer Handle Lock

Handle Lock Lever

Gearcase \

Slot

Rear Cartridge

Bolt

Handle Base

Pivot Bolt

_oc nut

INSERT CABLE CLIP

• Insert plastic came clip into hole on the

back of handle column. Push cables

into clip.

Handle Column

Cables

Cable Clip

handles 14

CONNECT SHIFT ROD

1. Insert end of shift rod farthest from

bend into hole of shift lever indicator.

2. Insert hairpin dip through hole of shift

rod to secure with bend of clip on right

side.

Attach this End To shift _ Shift Rod

Lever Indicator

Shift Lever

Hairpin Clip Indicator

Shift Rod

REMOVE TILLER FROM CRATE

1. Adjust handle assemby to lowest posi-

tion. Be sure lock lever is tightened

securely.

2. Make sure shift lever indicator is in "N"

(neutral) position.

3. Tilt tiller forward by lifting handle.

Separate cardboard cover from level-

ing shield.

4. Rotate tiller handle to the right and pull

tiller out of carton.

CHECK TiRE PRESSURE

The tires on your unit were overinflated at

the factory for shipping purposes, Correct

and equal tire pressure is important for

best tilling performance.

• Reduce tire pressure to 20 PSi.

HANDLE HEIGHT

• Handle height may be adjusted to bet-

ter suit operator. (See "TO ADJUST

HANDLE HEIGHT" in the Service and

Adjustments section of this manual).

These symbols mayappearon your Tiller or in literaturesuppliedwiththe product,

Learnand understandtheir meaning,

KNOW YOUR TILLER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

TILLER.

Compare the illustrations with your tiller to familiarize yourself with the location of

various controls and adjustments. Save this manual for future reference.

STO

t'h

TILLING FORWARD NEUTRAL REVERSE CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL

OR WARNING ON OFF

Fuel Valve On/Off

Switch

Throttle

Shift Lever

Choke

Drive Control Bar

Recoil

Starter

Handle

Shift Lever Indicator

Depth Stake

Leveling Shield .......... / ...........

/i / ,

Outer Side Shield .... _ '

MEETS ANSI SAFETY REQUIREMENTS

Our tillers conform to the safety standards of the American National Standards Institute.

CHOKE CONTROL = Used when starting

a cold engine

DEPTH STAKE - Controls depth at which

tiller will dig,

DRAG STAKE - Controls forward speed in

forward rotating till position,

DRIVE CONTROL BAR - Used to engage

tines,

FUEL VALVE =Used to turn fuel off and on,

LEVELING SHIELD - Levels tilled soil.

ON / OFF SWITCH = used to STOP the

engine.

OUTER SIDE SHIELD - Adjustable to

protect small plants from being buried.

RECOIL STARTER HANDLE - Used to

start the engine.

SHIFT LEVER - Used to shift transmission

gears,

SHIFT LEVER INDICATOR - Shows

which gear the transmission is in.

THROTTLE CONTROL - Used to control

engine speed,

The operation of any tiller can result in foreign objects thrown into the eyes,

which can result in severe eye damage. Always wear safety glasses or eye

shields before starting your tiller and while tilling. We recommend a wide vi-

sion safety mask over spectacles or standard safety glasses.

HOW TO USE YOUR TILLER

Know how to operate all controls before

adding fuel and oil or attempting to start

engine.

STOPPING

TINES

1. Release drive control bar to stop

movement.

2. Move shift lever to "N" (neutral) position.

ENGINE

2. Move throttle control to "SLOW" posi-

tion and allow the engine to run slowly

for cool down.

3. Turn the engine switch to the "OFF"

Position.

4. Turn the fuel valve lever to the "OFF"

Position.

NOTE: Never use choke to stop engine.

IMPORTANT: To stop engine in an emer-

gency, turn the engine switch to the OFF

position.

Drive Control Bar

"ENGAGED"

Shift Lever

Drive Control Bar

"DISENGAGED"

Position

Throttle

Control

Engine Fuel

Switch Valve

Throttle

Control

TINE OPERATION - WITH WHEEL

DRIVE

• Always release drive control bar before

moving shift lever into another position.

• Tine movement is achieved by moving

shift lever to (_) till position and engag-

ing drive control bar.

FORWARD - WHEELS ONLY/TINES

STOPPED

• Release drive control bar and move shift

lever indicator to "F" (forward) position.

Engage drive control bar and tiller will

move forward,

REVERSE - WHEELS ONLY/TINES

STOPPED

1. DO NOT STAND DIRECTLY BEHIND

TILLER.

2. Release the drive control bar.

3. Move throttle control to "SLOW" posi-

tion.

4. Move shift lever indicator to "R" (re-

verse) position.

5. Hold drive control bar against the

handle to start tiller movement.

HARD TO SHIFT GEARS

• Briefly engage drive control bar and

release or rock tiller forward and back-

ward until are able to shift gears.

DEPTH STAKE

The depth stake can be raised or lowered

to allow you more versatile tilling and cul-

tivating, or to more easily transport your

tiller.

Shallowest Tilling -...._

(Cultivating)

Deeptest Tilling_

Depth Stake ---------

-- Transport Position

Fuel

Valve

Engine

Switch

TILLING

1. Release depth stake pin. Pull the

depth stake up for increased tilling

depth. Place depth stake pin in hole of

depth stake to lock in position.

2. Place shift lever indicator in till position.

3. Hold the drive control bar against the

handle to start tilling movement. Tines

and wheels will both turn.

4. Move throttle control to "FAST" position

for deep tilling. To cultivate, throttle

control can be set at any desired

speed, depending on how fast or slow

you wish to cultivate.

IMPORTANT: Always release drive control

bar before moving shift lever into another

position.

Depth Stake Pin

"RELEASED" Position

Nut

"a"

"Locked"

Position

Side Shield

TURNING

1. Release the drive control bar.

2. Move throttle control to "SLOW" posi-

tion.

3. Place shift lever indicator in "F" (for-

ward) position. Tines will not turn.

4. Lift handle to raise tines out of ground.

5. Swing the handle in the opposite direc-

tion you wish to turn, being careful to

keep feet and legs away from tines.

6. When you have completed your turn-

around, release the drive control bar

and lower handle. Place shift lever in

(till) position and move throttle control

to desired speed. To begin tilling, hold

drive control bar against the handle.

TO TRANSPORT

_L, CAUTION: Before lifting or transport-

ing, allow tiller engine and muffler to cool.

Disconnect spark plug wire. Drain gaso-

line from fuel tank.

AROUND THE YARD

1. Release the depth stake pin. Move

the depth stake down to the top hole

for transporting the tiller. Place depth

stake pin in hole of depth stake to lock

in position. This prevents tines from

scuffing the ground.

2. Place shift lever indicator in "F" (for-

ward) position for transporting.

3. Hold the drive control bar against the

handle to start tiller movement. Tines

will not turn.

4. Move throttle control to desired speed. 10

AROUND TOWN

1. Disconnect spark plug wire.

2. Drain fuel tank.

3. Transport in upright position to prevent

oil leakage.

BEFORE STARTING ENGINE

IMPORTANT: Be very careful not to allow

dirt to enter the engine when checking or

adding oil or fuel. Use clean oil and fuel

and store in approved, clean, covered

containers, use clean fill funnels.

FILL ENGINE WITH OIL

Remove hangtag from engine.

With engine level, remove engine oil

filler plug.

Fill engine with oil to point of overflow-

ing. For approximate capacity see

"PRODUCT SPECIFICATIONS" on

page 4 of this manual. All oil must

meet A.RI. Service Classification SG-

SL.

Tilt tiller back on its wheels and then

re-level.

With engine level, refill to point of over-

flowing if necessary. Replace oil filler

plug.

For cold weather operation you should

change oil for easier starting (See "OIL

VISCOSITY CHART" in the Mainte-

nance section of this manual).

To change engine oil, see the Mainte-

nance section of this manual.

I /

_ ,/ j'_ Oil Filler

_'-"" __'_'/Plug

Max Upper Level_

Min Lower Level _

ADD GASOMNE

Fill fuel tank to bottom of filler neck. Do

not overfill. Use fresh, clean, regular

unleaded gasoline with a minimum of

87 octane. (Use of leaded gasoline will

increase carbon and lead oxide depos-

its and reduce valve life). Do not mix oil

with gasoline. Purchase fuel in quanti-

ties that can be used within 30 days to

assure fuel freshness.

_iILCAUTION: Fill to within 1/2 inch of top

of fuel tank to prevent spills and to allow

for fuel expansion. If gasoline is acciden-

tally spilled, move machine away from

area of spill. Avoid creating any source of

ignition until gasoline vapors have disap-

peared.

Wipe off any spilled oil or fuel. Do not

store, spill or use gasoline near an open

flame.

IMPORTANT: When operating in temper-

atures below32°F(0°C), use fresh, clean

winter grade gasoline to help insure good

cold weather starting.

CAUTION: Alcohol blended fuels (called

gasohol or using ethanol or methanol) can

attract moisture which leads to separation

and formation of acids during storage.

Acidic gas can damage the fuel system

of an engine while in storage. To avoid

engine problems, the fuel system should

be emptied before storage of 30 days

or longer. Drain the gas tank, start the

engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel

next season. See Storage Instructions for

additional information. Never use engine

or carburetor cleaner products in the fuel

tank or permanent damage may occur.

TO START ENGINE

_CAUTION: Keep tine control in "OFF"

position when starting engine.

When starting engine for the first time or

if engine has run out of fuel, it will take

extra pulls of the recoil starter to move fuel

from the tank to the engine.

1. Make sure spark plug wire is properly

connected.

2. Place the fuel valve to the "ON" posi-

tion.

3. To start a cold engine, move the choke

lever to the "ON" position.

4. Move the throttle lever away from the

"SLOW" position, about 1/3 of the way

toward the "FAST" position.

5. Turn the engine switch to the "ON" po-

sition. Pull rope out slowly until engine

reaches start of compression cycle

(rope will pull slightly harder at this

point).

6. Pull recoil starter handle quickly.

Do not let starter handle snap back

against starter. Repeat if necessary.

NOTE: If engine fires but does not start,

move choke control to half choke posi-

tion. Pull recoil starter handle until engine

starts.

Spark

Throttle

Choke

Control

Fuel Valve

Recoil Starter

Engine

Switch

TILLING HINTS

_,CAUTION: Until you are accustomed

to handling your tiller, start actual field

use with throttle in slow position (mid-way

between "FAST" and "IDLE").

• Tilling is digging into, turning over, and

breaking up packed soil before planting.

Loose, unpacked soil helps root growth.

Best tilling depth is 4" to 6". A tiller will

also clear the soil of unwanted vegeta-

tion. The decomposition of this vegeta-

ble matter enriches the soil. Depending

on the climate (rainfall and wind), it may

be advisable to till the soil at the end of

the growing season to further condition

the soil.

• Soil conditions are important for proper

tilling. Tines will not readily penetrate

dry, hard soil which may contribute to

excessive bounce and difficult handling

of your tiller. Hard soil should be mois-

tened before tilling; however, extremely

wet soil will "ball-up" or clump during

tilling. Wait until the soil is less wet in

order to achieve the best results. When

tilling in the fall, remove vines and long

grass to prevent them from wrapping

around the tine shaft and slowing your

tilling operation.

• You will find tilling much easier if you

leave a row untilled between passes.

Then go back between tilled rows.There

are two reasons for doing this. First,

wide turns are much easier to negoti-

ate than about-faces. Second, the tiller

won't be pulling itself, and you, toward

the row next to it.

• Do not lean on handle. This takes

weight off the wheels and reduces

traction. To get through a really tough

section of sod or hard ground, apply

upward pressure on handle or lower the

depth stake.

CULTIVATING

Cultivating is destroying the weeds be-

tween rows to prevent them from robbing

nourishment and moisture from the plants.

At the same time, breaking up the upper

layer of soil crust will help retain moisture

in the soil. Best digging depth is 1" to 3"

(2.5-7.5 cm).

• Cultivate up and down the rows at a

speed which will allow tines to uproot

weeds and leave the ground in rough

condition, promoting no further growth

of weeds and grass.

\ r i

(-'_> ('h>

( ,_?

\ _i

\ ,_"

\/ .i

(z', i

_jz

/f "_>

TINE SHEAR PINS

The tine assemblies on your tiller are

secured to the tine shaft with shear pins

(See "TINE REPLACEMENT" in the

Service and Adjustments section of this

manual).

If the tiller is unusually overloaded or

jammed, the shear pins are designed to

break before internal damage occurs to

the transmission.

• If shear pin(s) break, replace only with

those shown in the Repair Parts section

of this manual.

ADJUST WHEELS FOR

CULTIVATING

1. Place blocks under right hand side of

tiller and remove hairpin clip and clevis

pin from right hand wheel.

2. Move wheel outward approximately 1

inch until hole in inner wheel hub lines

up with inner hole in axle.

3. Replace clevis pin and hairpin clip on

inside of wheel and remove blocks.

4. Repeat preceding steps on left hand

side.

NOTE: In extremely rough conditions and

while cultivating, the wheels should be

moved outward on the axle for increased

stability.

OUTER VIEW OF TIRE

-- Clevis

7/_4

1"_" Hairpin Cllip

INNER VIEW OF TIRE

Clevis

Hairpin

Clip

tire 2

MAINTENANCE / / / / /

REGULAR SERVICE _'_'_'__'_'_"_'xM M M _

Check Engine 0il Level _

Change Engine Oil _1,2

Oil Pivot Points V_'

Inspect Spark Arrester / Muffler _'

Inspect Air Screen _'

Clean or Replace Air Cleaner Cartridge _2

Clean Engine Cylinder Fins

Replace Spark Plug

1 - Change more often when operating under a heavy load or in high ambient temperatures.

2 - Service more often when operating in dirty or dusty conditions.

SERVICE DATES

GENERAL RECOMMENDATIONS

The warranty on this tiller does not cover

items that have been subjected to opera-

tor abuse or negligence. To receive full

value from the warranty, the operator must

maintain tiller as instructed in this manual.

Some adjustments will need to be made

periodically to properly maintain your tiller.

At least once a season, check to see if

you should make any of the adjustments

described in the Service and Adjustments

section of this manual.

• At least once a year you should replace

the spark plug, clean or replace air filter,

and check tines and belts for wear. A

new spark plug and clean air filter as-

sure proper air-fuel mixture and help

your engine run better and last longer.

BEFORE EACH USE

1. Check engine oil level.

2. Checktine operation.

3. Check for loose fasteners.

LUBRICATION

Keep unit well lubricated (See "LUBRICA-

TION CHART").

QEngine

LUBRICATION CHART

QRH Gear Case

Grease Fitting

OIdler

Bracket OWheel Hub

ODepth Stake Pin

OLeveling

Shield

Hinges

O SAE 30 OR 10W-30 Motor Oil

Q Refer to Maintenance "ENGINE" section

Q EP#1 Grease

_L,CAUTION: Disconnect spark plug

wire before performing any maintenance

(except carburetor adjustment) to prevent

accidental starting of engine.

Prevent fires! Keep the engine free of

grass, leaves, spilled oil, or fuel. Remove

fuel from tank before tipping unit for main-

tenance. Clean muffler area of all grass,

dirt, and debris.

Do not touch hot muffler or cylinder fins as

contact may cause burns.

ENGINE

LUBRiCATiON

Use only high quality detergent oil rated

with API service classification SG-SL Se-

lect the oil's SAE viscosity grade accord-

ing to your expected temperature.

SAE VISCOSITY GRADES

=20 0 20 40 60 80 100°F

| l l 1 J [ • 1

=30 =20 =10 0 10 20 30 40 ° C

TEMPERATURE RANGE ANTiCiPATED BEFORE NEXT OiL CHANGE

NOTE: Although multi-viscosity oils

(5W-30, 10W-30, etc.) improve starting in

cold weather, they will result in increased

oil consumption when used above 32°F

(0°C). Check your engine oil level more

frequently to avoid possible engine dam-

age from running low on oil.

Change the oil after every 25 hours of op-

eration or at least once a year if the tiller is

not used for 25 hours in one year.

Check the crankcase oil level before

starting the engine and after each five (5)

hours of continuous use. Add SAE 30 mo-

tor oil or equivalent. Tighten oil filler plug

securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range expected

before oil change. All oil must meet API

service classification SG-SL

• Be sure tiller is on level surface.

• Oil will drain more freely when warm.

• Use a funnel to prevent oil spill on tiller,

and catch oil in a suitable container.

1. Remove drain plug.

2. Tip tiller forward to drain oil.

3. After oil has drained completely,

replace oil drain plug and tighten se-

curely.

4. Remove oil filler plug. Be careful not

to allow dirt to enter the engine.

5. Refill engine with oil. See "CHECK

ENGINE OIL LEVEE' in the Operation

section of this manual.

Oil drain

Level

Oil Fill Plug

AiR CLEANER

Service air cleaner cartridge every

twenty-five hours, more often if engine is

used in very dusty conditions.

1. Loosen air cleaner screw.

2. Remove air cleaner cover.

3. Carefully remove air cleaner cartridge.

Be careful. Do not allow dirt or debris

to fall into carburetor.

4. Clean by tapping gently on a flat sur-

face.

NOTE: If very dirty or damaged, replace

cartridge.

5. Clean and replace cover. Tighten

screw securely.

_CAUTION: Petroleum solvents, such

as kerosene, are not to be used to clean

cartridge. They may cause deterioration

of the cartridge. Do not oil cartridge. Do

not use pressurized air to clean or dry

cartridge.

Air Cleaner

Cartridge

Pre-Cleaner

Cover

Air Cleaner

Screws

COOLING SYSTEM

Your engine is air cooled. For proper en-

gine performance and long life keep your

engine clean.

• Clean air screen frequently using a

stiff-bristled brush.

• Remove blower housing and clean as

necessary.

• Keep cylinder fins free of dirt and chaff.

BIo_ver

Air Screen

Housing

MUFFLER

Do not operate tiller without muffler. Do

not tamper with exhaust system. Dam-

aged mufflers or spark attesters could

create a fire hazard. Inspect periodically

and replace if necessary. If your engine is

equipped with a spark arrester screen as-

sembly, remove every 50 hours for clean-

ing and inspection. Replace if damaged.

SPARK PLUG

Replace spark plugs at the beginning of

each tilling season or after every 25 hours

of use, whichever comes first. Spark plug

type and gap setting are shown in "PROD-

UCT SPECIFICATIONS" on page 4 of this

manual.

TRANSMISSION

Your transmission is sealed and will not

require lubrication unless serviced.

CLEANING

Do not clean your tiller when the engine

and transmission are hot. We do not rec-

ommend using pressurized water (garden

hose, etc.) to clean your unit unless the

gasket area around the transmission and

the engine muffler, air filter and carburetor

are covered to keep water out. Water in

engine will shorten the useful life of your

tiller.

• Clean engine, wheels, finish, etc. of all

foreign matter.

• Keep finished surfaces and wheels free

of all gasoline, oil, etc.

• Protect painted surfaces with automo-

tive type wax.

_ILCAUTION: Disconnect spark plug wire

from spark plug and place wire where it

cannot come into contact with plug.

TILLER

TO ADJUST HANDLE HEIGHT

Select handle height best suited for your

tilling conditions. Handle height will be

different when tiller digs into soil.

1. First loosen handle lock lever.

2. Handle can be positioned at different

settings between "HIGH" and "LOW"

positions.

3. Retighten handle lock lever securely

after adjusting.

HandLe (Low)

Position

HandLe (High) Position

HandLe Lock Lever

TIRE CARE

_ILCAUTION: When mounting tires, un-

less beads are seated, ovednflation can

cause an explosion.

• Maintain 20 pounds of tire pressure. If

tire pressures are not equal, tiller will

pull to one side.

• Keep tires free of gasoline or oil which

can damage rubber.

TO REMOVE WHEEL

Place blocks under transmission to

keep tiller from tipping.

Remove hairpin clip and clevis pin from

wheel.

Remove wheel and tire.

Repair tire and reassemble.

tire 3

Clevis Pin

Hairpin Clip

TO REMOVE BELT GUARD

NOTE: For ease of removal, remove hair-

pin clip and clevis pin from left wheel. Pull

wheel out from tiller about 1 inch.

1. Remove two (2) screws from side of

belt guard.

2. Remove hex nut and washer from

bottom of belt guard (located behind

wheel).

3. Pull belt guard out and away from unit.

4. Replace belt guard by reversing above

procedure.

Screws

Belt Guard

Hex

and

Washer

(Located

Behind

Tire)

Hairpin Clip and Clevis Pin

TO REPLACE GROUND DRIVE BELT

1. Remove belt guard as described in

"TO REMOVE BELT GUARD".

2. Remove old belt by slipping off engine

pulley first then remove from transmis-

sion pulley.

3. Place new belt in groove of transmis-

sion pulley and into engine pulley.

BELT MUST BE IN GROOVE ON TOP

OF IDLER PULLEY, NOTE POSITION

OF BELT TO GUIDES.

4. Check belt adjustment as described

below.

5. Replace belt guard.

6. Reposition wheel and replace clevis

pin and hairpin clip.

GROUND DRIVE BELT ADJUSTMENT

For proper belt tension, the extension

spring should have about 5/8 inch stretch

when drive control bar is in "ENGAGED"

position. This tension can be attained as

follows:

1. Loosen cable clip screw securing the

drive control cable.

2. Slide cable forward for less tension

and rearward for more tension until

about

5/8 inch stretch is obtained while the

drive control bar is engaged.

3. Tighten cable clip screw securely.

Engine Pulley\

Clip Screw

Drive Control Cable

Idler Pulley

Extension Spring

Transmission Pulley

More Tension

TINE REPLACEMENT

J_,CAUTION: Tines are sharp. Wear

gloves or other protection when handling

tines.

A badly worn tine causes your tiller to

work harder and dig more shallow. Most

important, worn tines cannot chop and

shred organic matter as effectively nor

bury it as deeply as good tines. A tine this

worn needs to be replaced.

• To maintain the superb tilling perfor-

mance of this machine the tines should

be checked for sharpness, wear, and

bending, particularly the tines which

are next to the transmission. If the gap

between the tines exceeds 3-1/2 inches

they should be replaced or straightened

as necessary.

• New tines should be assembled. Sharp-

ened tine edges will rotate rear

New Tine

TJne

Tin

_-3-1/2" Max

Counter Tine

Rotation

Shear Pin

Sharp Edge

Shear Pin ----._

Sharp Edge _

p Edge

Hairpin Clip

12 Sharp Edges

ENGINE

Maintenance, repair, or replacement of

the emission control devices and systems,

which are being done at the customers ex-

pense, may be performed by any non-road

engine repair establishment or individual.

Warranty repairs must be performed by an

authorized engine manufacturer's service

outlet.

iMPORTANT: Never tamper with the

engine governor, which is factory set for

proper engine speed. Overspeeding

the engine above the factory high speed

setting can be dangerous. If you think

the engine-governed high speed needs

adjusting, contact your nearest sears or

other qualified service center which has

the proper equipment and experience to

make any necessary adjustments.

TO ADJUST CARBURETOR

The carburetor has been preset at the

factory and adjustment should not be

necessary. However, engine performance

can be affected by differences in fuel, tem-

perature, altitude or load. If the carburetor

does need adjustment, contact your near-

est authorized service center/department

iMPORTANT: Never tamper with the

engine governor, which is factory set for

proper engine speed. Overspeeding

the engine above the factory high speed

setting can be dangerous. If you think

the engine-governed high speed needs

adjusting, contact your nearest sears or

other qualified service center which has

the proper equipment and experience to

make any necessary adjustments.

Immediately prepare your tiller for storage

at the end of the season or if the unit will

not be used for 30 days or more.

_i_CAUTION: Never store the tiller with

gasoline in the tank inside a building

where fumes may reach an open flame

or spark. Allow the engine to cool before

storing in any enclosure.

TILLER

1. Clean entire tiller (See "CLEANING"

in the Maintenance section of this

manual).

2. Inspect and replace belts, if necessary

(See belt replacement instructions in

the Service and Adjustments section of

this manual).

3. Lubricate as shown in the Maintenance

section of this manual.

4. Be sure that all nuts, bolts and screws

are securely fastened. Inspect moving

parts for damage, breakage and wear.

Replace if necessary.

5. Touch up all rusted or chipped paint

surfaces; sand lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT: It is important to prevent

gum deposits from forming in essential

fuel system parts such as the carburetor,

fuel filter, fuel hose, or tank during stor-

age. Also, alcohol blended fuels (called

gasohol or using ethanol or methanol) can

attract moisture which leads to separation

and formation of acids during storage.

Acidic gas can damage the fuel system of

an engine while in storage.

• Empty the fuel tank by starting the en-

gine and letting it run until the fuel lines

and carburetor are empty.

• Never use engine or carburetor cleaner

products in the fuel tank or permanent

damage may occur.

• Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable

alternative in minimizing the formation of

fuel gum deposits during storage. Add

stabilizer to gasoline in fuel tank or stor-

age container. Always follow the mix ratio

found on stabilizer container. Run engine

at least 10 minutes after adding stabilizer

to allow the stabilizer to reach the carbure-

tor. Do not empty the gas tank and carbu-

retor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace

with clean oil. (See "ENGINE" in the

Maintenance section of this manual).

CYLINDER

1. Remove spark plug.

2. Pour 1 ounce (29 ml) of oil through

spark plug hole into cylinder.

3. Pull starter handle slowly several times

to distribute oil.

4. Replace with new spark plug.

OTHER

• Do not store gasoline from one season

to another.

• Replace your gasoline can if your can

starts to rust. Rust and/or dirt in your

gasoline will cause problems.

• If possible, store your unit indoors and

cover it to give protection from dust and

dirt.

• Cover your unit with a suitable protec-

tive cover that does not retain moisture.

Do not use plastic. Plastic cannot

breathe which allows condensation to

form and will cause your unit to rust.

IMPORTANT: Never cover tiller while en-

gine and exhaust areas are still warm.

TROUBLESHOOTING CHART:

See appropriate section in manual unless directed to Sears service center

PROBLEM CAUSE CORRECTION

Will not start

Hard to start

Loss of power

1 Out of fuel.

2 Fuel valve "OFF"

3 Engine Switch "OFF"

4 Engine not "CHOKED" properly.

5 Engine flooded.

6 Bad spark plug or improper gap.

7 Dirty air filter.

8 Water in fuel.

1 Throttle control not set properly.

2 Dirty air filter.

3 Bad spark plug or improper gap.

4 Stale or dirty fuel.

5 Loose spark plug wire.

1 Engine is overloaded

2 Dirty air cleaner

3 Low oil level/dirty oil.

4 Faulty spark plug.

5 Oil in fuel

6 Stale or dirty fuel.

7 Water in fuel.

8 Clogged fuel tank.

9 Spark plug wire loose.

10 Dirty engine air screen.

11 Dirty/clogged muffler.

12 Poor Compression

1 Low oil level/dirty oil.

2 Dirty engine air screen.

3 Dirty engine.

4 Partially plugged muffler

Engine

overheats

1 Fill fuel tank.

2 Turn fuel valve to the "ON" position.

3 Turn engine switch to the "ON" position.

4 See"TO START ENGINE" in Operation

section.

5 Wait several minutes before attempting

to start.

6 Replace spark plug or adjust gap.

7 Clean/replace air filter.

8 Empty fuel tank and carburetor, refill

tank with fresh gasoline.

1 See"To Start Engine" in Operations

section.

2 Clean/replace air filter.

3 Replace spark plug or adjust gap.

4 Empty fuel tank and refill tank with

fresh, clean gasoline.

5 Make sure spark plug wire is seated

properly.

1 Set depth stake and wheels for

shallower tilling.

2 Clean/replace air filter.

3 Check oil level/change oil.

4 Clean and regap or change spark plug.

5 Empty and clean fuel tank and refill,

and clean carburetor.

6 Empty fuel tank and refill tank with

fresh, clean gasoline.

7 Empty fuel tank and carburetor, refill

tank with fresh gasoline.

8 Remove fuel tank and clean.

9 Connect and tighten spark plug wire.

10 Clean engine air screen.

11 Clean/replace muffler.

12 Contact a Sears or other qualified

service center.

1 Check oil level/change oil.

2 Clean engine air screen.

3 Clean cylinder fins, airscreen, muffler

area

4 Remove and clean muffler.

Page is loading ...

Craftsman 917299061 Owner's manual

Brand: Craftsman

Model: 917299061

Category: Mini tillers

Type: Owner's manual

This manual is also suitable for

917.299061

Download PDF

report

in other languages

español: Craftsman 917299061 El manual del propietario

Craftsman 917299061 Owner's manual

This manual is also suitable for

Craftsman 917299061 Owner's manual

in other languages

Related papers

Other documents