Lifetime 91099 Owner's manual

Brand: Lifetime

Model: 91099

Type: Owner's manual

Lifetime 91099 is a sit-on-top fishing kayak designed for use in open water. It features a water-resistant hatch for storage, a tiller handle for steering, and universal accessory mounting tracks for customization. The kayak's durable polyethylene construction and 350-pound capacity make it suitable for both recreational and fishing use. It also includes a fold-down angler seat with adjustable handles for comfort and support.

Registration..................................2

Safety Instructions............................2

Parts Identiﬁer..................................3

Features.........................................4

Seat Assembly..................................5

Rudder Assembly...........................11

Pedal Drive Assembly.....................16

General Use & Transport................20

Warning Sticker & Maintenance.....23

Warranty....................................27

TOOLS REQUIRED

Save this instruction in the event you need to contact the manufacturer.

TABLE OF CONTENTS

OWNER’S

MANUAL

Product ID:

CONTACT LIFETIME® CUSTOMER SERVICE:

Dial 1-800-225-3865

(English, Spanish, French)

Live Chat: www.lifetime.com/customerservice/home

QUESTIONS?

SIT-ON-TOP FISHING KAYAK

RENEGADE 116™

(x1, included)

1/8"

(x1, included)

5/32"

GET ASSEMBLY HELP

WATCH THE INSTRUCTIONAL VIDEOS ON YOUTUBE.

Scan the code, or search http://go.lifetime.com/pedaldrive

**For customers outside the U.S. or Canada, please contact the store for assistance.**

**U.S. and Canada customers ONLY**

IF ASSISTANCE IS NEEDED,

DO NOT CONTACT THE STORE!

CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) 225-3865

Most injuries are caused by misuse and/or not following instructions. Use caution when using this system.

To ensure safety, do not attempt to use this product without following the instructions

carefully. Check entire product and inside all packing material for parts and/or additional

instruction material. Before using this watercraft, read the instructions and identify

parts using the identiﬁ er in this document. Proper and complete assembly, use, and

supervision are essential to reduce the risk of accident or injury. A high probability of

serious injury exists if this system is not assembled, maintained, and/or operated properly.

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID

WARRANTY.

• Follow any and all warnings and cautions carefully.

• Inspect the hull for damage prior to each use.

SAFETY INSTRUCTIONS

LIFETIME’S PROMISE TO YOU:

We invite you to read our privacy policy at www.lifetime.com

At Lifetime®, we are committed to providing innovative and quality products. While registering, you will have the op-

portunity to give us your feedback. Your input is valuable to us.

• You can also opt in to receive new product notiﬁ cations or promotions.

• In the unlikely event of a product recall or safety modiﬁ cation, your registration

provides the information we need to notify you directly.

• Registration is fast, easy, and completely voluntary.

Maintaining your privacy is our long-standing policy at Lifetime®. And you can rest

assured that Lifetime® will not sell or provide your personal data to other third

parties, or allow them to use your personal data for their own purposes.

GXL (x1)

Paddle may vary from model shown

PARTS IDENTIFIER

HARDWARE REQUIRED

GXK (x1)

GXJ (x1)

GXB (x2) AYU (x2)

GXH (x1)

GXI (x1) (Left) HDI (x1) (Right)

GXE (x1)

GXD (x1)

Hardware bag

GTJ

Large parts

GXS (x1)

Speciﬁcations:

Length: 11 feet 6 inches (350,5 cm)

Width: 32 inches (81,2 cm)

Weight: 99 lb (44,9 kg)

Maximum Weight Capacity: 350 lb (158,8 kg)*

*Capacity depends on water conditions.

**Never drag any portion of the kayak over asphalt or any rocky, sandy, or abrasive surface.

• UV-Protected Durable, High-Density

Polyethylene (HDPE) Construction

FEATURES

Paddle keeper

Fold-Down Angler Seat

Tiller handle

Universal accessory

mounting tracks

Water-resistant

hatch

Drain Plug

Fishing Rod Holders

Hull ID

Rudder deploy-

ment cord

GXA (x2)

HARDWARE REQUIRED

PARTS REQUIRED

TOOLS REQUIRED

GXC (x2)

SEAT ASSEMBLY

GXK (x1)

GXJ (x1)

GXB (x2) AYU (x2)

Hardware Bag

GTJ

u SECTION 1

TOOLS AND HARDWARE REQUIRED

• In case you have trouble with the assembly in this section, check out our

assembly-help video by scanning the QR code below or by entering the address in

any browser:

• When unpacking the kayak for the ﬁrst time, remove the seat (GXJ)

from the kayak and unfold.

1.1

GXJ

http://go.lifetime.com/pedaldrive-section1

u SECTION 1

TOOLS AND HARDWARE REQUIRED

• On the bottom of the seat, wrap the wings of the seat around the

seat frame and securely tighten the straps.

1.2

u SECTION 1

TOOLS AND HARDWARE REQUIRED

• Slide each carriage bolt (GXA) about halfway up the seat tracks.

1.3

• Slide a seat bracket (GXB) onto the forward-facing cross bar on the

seat frame.

1.4

GXA (x2)

GXB

Seat track

GXA

u SECTION 1

TOOLS AND HARDWARE REQUIRED

• Lower the seat onto the seat tracks so the bolts pass through the

hole in the seat brackets.

1.5

• Press a hex nut (GXC) into the top of each adjustment handle (AYU), then

use the adjustment handles to secure the seat to the seat track.

1.6

GXC (x2)

GXC

AYU

• To adjust the seat, loosen both handles and slide the seat

to the desired position, then tighten the handles again.

u SECTION 1

TOOLS AND HARDWARE REQUIRED

• Locate the strap on the lower rear cross tube of the seat. Run the

strap through the loop behind the seat, pulling hard to allow the

stitched seam on the strap through the loop. Fasten the strap until

the seam is ﬂush with the buckle. This strap will keep the seat

tethered to the kayak while remaining loose enough to adjust the

position of the seat as needed.

1.7

Stitched seam

• Remove the seat and stow it in

your vehicle during over-the-road

transportation.

RUDDER ASSEMBLY

HARDWARE REQUIRED

PARTS REQUIRED

TOOLS REQUIRED

GXH (x1)

GXS (x1)

u SECTION 2

TOOLS AND HARDWARE REQUIRED

• In case you have trouble with the assembly in this section, check out our

assembly-help video by scanning the QR code below or by entering the address in

any browser:

• Remove the cotter ring from the pin on the bottom of the rudder

assembly (GXH). Insert the pin into the bracket at the back of the hull.

2.1

GXH

Cotter Ring

http://go.lifetime.com/pedaldrive-section2

u SECTION 2

TOOLS AND HARDWARE REQUIRED

2.2 • Insert the cotter ring back through the hole at the bottom of the pin

to secure the rudder assembly to the bracket.

Cotter Ring

u SECTION 2

TOOLS AND HARDWARE REQUIRED

2.3

2.4

• Turn the rudder just enough to insert the control rod into the clamp.

• Face the rudder and tiller handle straight forward, then tighten the knob.

• If the kayak begins steering sharply to

one side, loosen the knob and reset the

tiller handle and rudder to these centered

positions. Then retighten the knob.

u SECTION 2

TOOLS AND HARDWARE REQUIRED

2.5

• Pull the cord toward the front of the kayak to raise the rudder. The

rudder should be stored in this retracted position whenever the kayak is not

in use.

• Thread the end of the pull cord (GXS) through the pad eyes (1 & 2),

and tie it to the lower hole (3) in the rudder. Press the pull cord into

the cleat (4).

Cleat

Toggle ball

Lower hole Upper hole

Pad eyes

2.6

PEDAL DRIVE ASSEMBLY

HARDWARE REQUIRED

PARTS REQUIRED

TOOLS REQUIRED

GXF (x2)

GXG (x2)

GXI (x1) (Left) HDI (x1) (Right)

GXE (x1)

GXD (x1)

5/32"

(x1, included)

Adjustable (x1)

AKH (x1)

GTJ

Hardware bag

GXP (x1) 1/8"

GXQ (x1) 5/32”

1/8"

(x1, included)

GXR (x2)

u SECTION 3

TOOLS AND HARDWARE REQUIRED

• In case you have trouble with the assembly in this section, check out our

assembly-help video by scanning the QR code below or by entering the address in

any browser:

http://go.lifetime.com/pedaldrive-section3

GXF (x2) GXG (x2)

1/8” (x1)

(x1)

5/32” (x1)

AKH (x1)

3.1 • Apply a thin layer of silicone grease (AKH) to the end the brace (GXD).

Loosen the hardware shown, then insert the brace into the pedal

drive assembly (GXE). Secure the brace to the pedal drive assembly (GXE)

using the hardware shown, then tighten the hardware.

GXF (x2)

GXG (x2)

GXE

AKH

GXE

GXD

Loosen

u SECTION 3

TOOLS AND HARDWARE REQUIRED

• Use an adjustable wrench to attach

the left and right pedals (GXI and

HDI) to the the crank arms of the

pedal drive assembly. Please note,

the two pedals are different; the left

pedal (GXI) must be turned

counterclockwise to tighten.

The ends of the pedal shafts

are stamped with an “L”

and an “R,” indicating which

is the left pedal and which is

the right pedal.

3.3

HDI

GXI

(x1)

• Insert a plug (GXR) into each end of the cross tube on the brace (GXD).

3.2

GXR (x2)

GXD

GXI

GXR

u SECTION 3

TOOLS AND HARDWARE REQUIRED

• Place the brace in the recess of the hull, and rest the pedal drive

assembly on the cover tray.

3.4

3.5 • Secure the brace to the hull

by turning the lock knobs into

the locked position.

Cover tray

• Remove the pedal drive

mechanism and stow it in your

vehicle during over-the-road

transportation.

GENERAL USE & TRANSPORT

SHALLOW WATER / PADDLE MODE / STORAGE

• Do not deploy the pedal drive or the rudder in shallow water or in areas where rocks, plant life or other

obstacles may come into contact with the kayak or its components.

• Always bring a paddle when using the kayak.

• Always raise the pedal drive mechanism and the rudder before paddling into shore.

When launching the kayak, returning to shore, or paddling in shallow water, raise the rudder and the

pedal drive out of the water as shown. The pedal drive mechanism will rest on top of the cover tray.

• Lift and pull the cord forward to raise

the rudder. Press the cord back into the

clam cleat to secure.

• Lift and slide the cover tray back under the seat.

Raise the pedal drive, then slide the cover tray

back into place and rest the pedal drive on top.

GXL (x1)

Paddle may vary from model shown

• Use the kayak paddle to manuever in shallow water

• In case you have trouble with the assembly in this section, check out our

assembly-help video by scanning the QR code below or by entering the address in

any browser:

http://go.lifetime.com/pedaldrive-section4

Page is loading ...

Lifetime 91099 Owner's manual

Lifetime 91099 Owner's manual

Lifetime 91099 Owner's manual

Related papers

Other documents