GROHE ATRIO 25 044 Instructions Manual

DESIGN + ENGINEERING

GROHE GERMANY

www.grohe.com

ATRIO

95.960.231/ÄM 243447/10.18

25 044

I

Please pass these instructions on to the end user of the fitting.

S.v.p remettre cette instruction à l'utilisateur de la robinetterie!

Bitte diese Anleitung an den Benutzer der Armatur weitergeben!

A

B

1

0

m

C

D

8

m

2

C

E

F

8

m

3

M

J

N

L

4

mm

K

5

O

L

P

P1

K

3

m

4

m

6

R

S

T

U

U1

1

7

m

7

H

E

G

8

m

4

Page is loading ...

2

GB

Application

Can be used in conjunction with: Pressurised storage

heaters, thermally and hydraulically controlled

instantaneous heaters. Operation with low-pressure

displacement water heaters is not possible.

Specifications

• Flow pressure min. 0.5 bar - recommended 1 - 5 bar

• Operating pressure max. 10 bar

• Test pressure 16 bar

If static pressure is greater than 5 bar, fit pressure

reducer.

Avoid major pressure differences between hot and

cold water supply.

• Temperature

Hot water inlet: (maximum) 70 °C

Recommended: (energy saving) 60 °C

• Water connection cold - right

hot - left

Installation

Refer to the dimensional drawing.

Screw-mount the mixer, see fold-out page I

Figs. [1] to [5].

1. Remove cover (A) from concealed mixer housing

and crosscut mounting template (B) to 10mm,

see Fig. [1].

2. Unscrew screw (C) using a 8mm socket spanner,

and remove flushing plug (D), see Fig. [2].

3. Plug in pre-mounted mixer assembly (E) on

concealed mixer housing (F), align radially and

tighten with screw (C), see Fig. [3].

4. If necessary, loosen screws (G) and align the

mixer (E) horizontally and vertically to the floor,

see Fig. [4].

5. Grout the joint around the mounting template with a

permanently elastic material.

6. Slip escutcheon (H) against the floor.

7. Plug in pre-mounted fitting (J) into pillar unions (K)

and tighten with set screws (L) using a 4mm socket

spanner, see Fig. [5].

8. Fit swivel spout (M).

Open cold and hot-water supply and check

connections for leakage!

Operation of automatic diverter (N), see Fig. [5].

Turning the handles will release water delivery.

Water will emerge from the bath spout first.

Press diverter knob = to divert flow from bath

spout to shower outlet

Pull diverter knob = to divert flow from shower

outlet to bath spout

Flow is diverted automatically from shower outlet to

bath spout when the mixer is turned off.

Maintenance

Inspect and clean all parts, replace as necessary and

grease with special grease.

Shut off cold and hot water supply!

I. Replacing the handspray holder, see Fig. [6].

1. Loosen set screws (O) using a 3mm socket spanner

and pull off fitting.

2. Loosen set screw (L) using a 4mm socket spanner

and pull off handspray holder (P) out of pillar

union (K).

3. Change handspray holder (P) and seals (P1).

Observe that there is no water in the sealing area of

the pillar union.

II. Replacing the headpart, see Fig. [7].

1. Pull off handle (R).

2. Unscrew screw (S) and pull off snap insert (T).

3. Unscrew headpart (U) using a 17mm socket wrench.

4. Change either complete headpart (U) or

O-ring (U1).

Observe the correct installation position!

III.Remove non-return valve, see fold-out page II.

IV. Unscrew and clean mousseur, see fold-out page II.

Assemble in reverse order.

Replacement parts, see fold-out page II

( * = special accessories).

Care

For directions on the care of this fitting, refer to the

accompanying Care Instructions.

Page is loading ...

2016/09/28

www.grohe.com

D

&

+49 571 3989 333

[email protected]

A

&

+43 1 68060

[email protected]

AUS

&

+(61) 1300 54945

[email protected]

B

&

+32 16 230660

[email protected]

BG

&

+359 2 9719959

grohe-bulgaria@grohe.com

BR

&

0800 770 1222

[email protected]

CAU

&

+99 412 497 09 74

[email protected]

CDN

&

+1 888 6447643

[email protected]

CH

&

+41 44 877 73 00

[email protected]

CN

&

+86 4008811698

[email protected]m

CY

&

+357 22 465200

[email protected]

CZ

&

+358 942 451 390

[email protected]m

DK

&

+45 44 656800

[email protected]

E

&

+34 93 3368850

[email protected]

EST

&

+372 6616354

[email protected]

F

&

+33 1 49972900

[email protected]

FIN

&

+358 942 451 390

[email protected]

GB

&

+44 871 200 3414

[email protected]

GR

&

+30 210 2712908

[email protected]rthnet.gr

H

&

+36 1 2388045

[email protected]

HK

&

+852 2969 7067

[email protected]

I

&

+39 2 959401

[email protected]

IND

&

+91 1800 102 4475

[email protected]

IS

&

+354 515 4000

[email protected]

J

&

+81 3 32989730

[email protected].jp

KZ

&

+7 727 311 07 39

[email protected]

LT

&

+372 6616354

[email protected]

LV

&

+372 6616354

[email protected]

MAL

[email protected]

MX

&

01800 8391200

pregunta@grohe.com

N

&

+47 22 072070

[email protected]

NL

&

+31 79 3680133

[email protected]

NZ

technicalenquiries@paterson

trading.co.nz

P

&

+351 234 529620

[email protected]

PL

&

+48 22 5432640

[email protected]

RI

&

0-800-1-046743

customercare-

[email protected]

RO

&

+40 21 2125050

[email protected]

ROK

&

+82 2 1588 5903

info-singapore@grohe.com

RP

&

+63 2 8938681

RUS

&

+7 495 9819510

info@grohe.ru

S

&

+46 771 141314

[email protected]

SGP

&

+65 6311 3611

info-singapore@grohe.com

SK

&

+420 277 004 190

[email protected]

T

&

+66 21681368

(Haco Group)

[email protected].th

TR

&

+90 216 441 23 70

GroheTurkey@grome.com

UA

&

+38 44 5375273

[email protected]m

USA

&

+1 800 4447643

us-customerservice@grohe.com

VN

&

+84 90 9694768

&

+84 90 9375068

info-vietnam@grohe.com

BiH

AL

HR

KS

ME

MK

SLO

SRB

&

+385 1 2911470

[email protected]

Eastern Mediterranean,

Middle East - Africa

Area Sales Office:

&

+357 22 465200

[email protected]

IR

OM

UAE YEM

&

+971 4 3318070

[email protected]m

Far East Area Sales Office:

&

+65 6311 3600

[email protected]

Latin America:

&

+52 818 3050626

[email protected]

GROHE ATRIO 25 044 Instructions Manual

GROHE ATRIO 25 044 Instructions Manual

in other languages

Related papers

Other documents