LG SK10Y User manual

MODEL

SK10Y (SK10Y, SPK8-W)

Please read this manual carefully before operating your set and retain it for

future reference.

www.lg.com

OWNER’S MANUAL

LG Wi-Fi

Sound Bar

1 Getting Started

Getting Started2

Getting Started

1

Safety Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning ash with arrowhead

symbol within an equilateral triangle

is intended to alert the user to the

presence of uninsulated dangerous

voltage within the product’s

enclosure that may be of sufcient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an

equilateral triangle is intended

to alert the user to the presence

of important operating and

maintenance (servicing) instructions

in the literature accompanying the product.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK

HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN

OR MOISTURE.

WARNING: Do not install this equipment in a

conned space such as a book case or similar unit.

CAUTION: Do not use high voltage products around

this product. (ex. Electrical swatter) This product may

malfunction due to electrical shock.

CAUTION: The apparatus should not be exposed to

water (dripping or splashing) and no objects lled

with liquids, such as vases, should be placed on the

apparatus.

CAUTION: Do not block any ventilation openings.

Install in accordance with the manufacturer’s

instructions.

Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of

the product and to protect it from over heating.

The openings shall never be blocked by placing

the product on a bed, sofa, rug or other similar

surface. This product shall not be placed in a built-

in installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer’s

instruction has been adhered to.

CAUTION: No naked ame sources, such as lighted

candles, should be placed on the apparatus.

NOTICE: For safety marking information including

product identication and supply ratings, please refer

to the main label on the bottom or the other surface

of the product.

CAUTION concerning the Power Cord

The Power Plug is the disconnecting device. In case

of an emergency, the Power Plug must remain readily

accessible.

Check the specication page of this owner’s manual

to be certain of the current requirements.

Do not overload wall outlets. Overloaded wall outlets,

loose or damaged wall outlets, extension cords, frayed

power cords, or damaged or cracked wire insulation

are dangerous. Any of these conditions could result

in electric shock or re. Periodically examine the

cord of your device, and if its appearance indicates

damage or deterioration, unplug it, discontinue use of

the device, and have the cord replaced with an exact

replacement part by an authorized service center.

Protect the power cord from physical or mechanical

abuse, such as being twisted, kinked, pinched, closed

in a door, or walked upon. Pay particular attention to

plugs, wall outlets, and the point where the cord exits

the device.

Getting Started 3

Getting Started

1

This device is equipped with a portable battery or

accumulator.

How to Safely remove the batteries or the

battery pack from the equipment: To Remove the

old batteries or battery pack, follow the assembly

steps in reverse order. To prevent contamination of

the environment and bring on possible threat to

human and/or animal health, the old batteries or the

battery pack must be put in an appropriate container

at designated collection points. Do not dispose

of batteries or battery pack together with other

waste. It is recommended that you use local, free

reimbursement systems batteries or battery packs,

(may not be available in your area). The batteries or

the battery pack should not be exposed to excessive

heat such as sunshine, re or the like.

Symbols

~

Refers to alternating current (AC).

0

Refers to direct current (DC).

Refers to class II equipment.

1

Refers to stand-by.

!

Refers to “ON” (power).

Refers to dangerous voltage.

Table of Contents4

2 Connecting

14 Organizing cables

14 Wireless subwoofer and rear speaker (Sold

Separately) connection

14 – Wireless subwoofer connection

16 – Rear speakers connection (Sold

Separately)

17 – Surround sound

20 – How to Affix the Ferrite Core

21 Connecting to your TV

21 – Using an OPTICAL cable

21 – LG Sound Sync

23 – Using an HDMI cable

23 – ARC (Audio Return Channel) function

23 – What is SIMPLINK?

24 – Additional information for HDMI

25 Optional equipment connection

25 – DOLBY ATMOS®

26 – HDMI connection

26 – OPTICAL IN connection

27 – PORTABLE IN connection

28 Network connection

28 – Wired connection

29 – Wireless connection

29 “LG Wi-Fi Speaker”

30 – Installing “LG Wi-Fi Speaker” App

30 Works with the Google Assistant

Table of Contents

1 Getting Started

2 Safety Information

6 Main Features

6 Introduction

7 Remote control

8 Front panel

9 Rear panel

11 Installing the sound bar

11 Mounting the main unit on a wall

13 Positioning the speakers (Optional)

Table of Contents 5

1

2

3

4

5

Some of the content in this manual may differ from “LG Wi-Fi Speaker” app depending on the application’s

version.

3 Operating

31 Using a Bluetooth Wireless Technology

31 – About Bluetooth

31 – Bluetooth profiles

31 – Listening to Music of a Bluetooth Device

33 – Bluetooth connection lock (BT LOCK)

33 Other operations

33 – Using your TV remote control

34 – AV Sync

34 – Turn off the sound temporarily

34 – Auto display Dimmer

34 – Displaying input source information

34 – Auto power down

35 – AUTO POWER On/Off

36 – Auto function change

37 Sound adjustment

37 – Setting sound effect

37 – Adjust volume level automatically

37 – Adjust Sound level

38 Standby mode

38 – Standby mode

38 – Network standby mode

38 – Bluetooth standby mode

38 Reset the Speaker

4 Troubleshooting

39 Troubleshooting

39 – General

40 – Network

41 – Application

41 – NOTES to use wireless

42 – NOTES to release Demo mode

5 Appendix

43 File requirement

43 Trademarks and licenses

44 Specifications

46 Handling the Speaker

46 Important Information Relating to Network

Services

47 TERMS OF USE

Getting Started6

Getting Started

1

Main Features

LG Sound Sync

Controls volume level of this unit by the remote

control of your LG TV that is compatible with LG

Sound Sync.

“LG Wi-Fi Speaker” application

Listens to music stored on your smart device.

You can control this speaker with your iPod touch/

iPhone or Android device via “LG Wi-Fi Speaker”

app. This speaker and your smart device must be

connected to the same network. Visit Apple “App

Store” or Google “Play Store” to search for “LG Wi-Fi

Speaker” app. For detailed information, refer to page

30.

y

Depending on the application’s version and the

software of smart device, “LG Wi-Fi Speaker” app

may not be operated normally.

y

Some smart devices may not be compatible with

this speaker.

Bluetooth®

Listens to music stored on your Bluetooth device.

Surround sound

You can enjoy surround sound by using Wireless Rear

Speaker kit (SPK8-S).

Introduction

Symbol used in this manual

,

Note

Indicates special notes and operating features.

>

Caution

Indicates cautions for preventing possible damages

from abuse.

Getting Started 7

Getting Started

1

Remote control

Replacement of Battery

Remove the battery cover on the rear of the remote

control, and insert the battery with

4

and

5

matched correctly.

• • • • • • • • • • • • • •

a

• • • • • • • • • • • • •

1

(Standby): Switches the unit ON or OFF.

VOL (Volume)

o

/

p

: Adjusts speaker volume.

F (Function): Selects the function and the input

source.

Input source / Function Display

Wi-Fi WI-FI

Optical

ARC

LG Sound Sync (Wired)

OPT/HDMI ARC

Bluetooth BT

LG Sound Sync (Wireless) LG TV

HDMI IN 1 HDMI IN 1

HDMI IN 2 HDMI IN 2

Portable PORTABLE

[

(Mute): Mutes the sound.

C

/

V

(Skip): Skips Fast backward or Forward.

N

(Play/Pause): Starts playback. / Pauses playback.

• • • • • • • • • • • • • •

b

• • • • • • • • • • • • •

SOUND EFFECT: Selects a sound effect mode.

: Adjusts sound level of each speaker. (Page

37)

AV SYNC:

- Synchronizes the audio and video.

- Controls TV remote. (Page 33)

J

:

- Displays the input source information.

- Displays the connected Bluetooth device name on

Bluetooth function.

AUTO VOL:

- Turns on or off the AUTO VOLUME mode.

- Turns on or off the surround sound. (Page 17)

AUTO POWER:

- Turns on or off AUTO POWER function.

(Page 35)

- Turns on or off the Bluetooth connection lock.

(Page 33)

Getting Started8

Getting Started

1

A

1

(Standby)

Switches the unit ON or OFF.

F (Function)

Selects the function and input source. (WI-FI,

OPT/HDMI ARC, BT, LG TV, HDMI IN1, HDMI IN2,

PORTABLE)

p

/

o

(Volume)

/

(Wi-Fi)

Selects Wi-Fi function.

B

LED indicator

Shows connection status.

y

White (Blinking): Waiting for network connection

on Wi-Fi function

y

White (Staying on): Network connection is

completed on Wi-Fi function or the other

functions are selected.

y

White (Dimmed): Standby mode with network

connection.

y

Red (Staying on): Standby mode without network

connection.

C

Remote sensor

D

Display window

Precautions in using the touch buttons

y

Use the touch buttons with clean and dry

hands.

- In a humid environment, wipe out any

moisture on the touch buttons before

using.

y

Do not press the touch buttons hard to make

it work.

- If you apply too much strength, it can

damage the sensor of the touch buttons.

y

Touch the button that you want to work in

order to operate the function correctly.

y

Be careful not to have any conductive material

such as metallic object on the touch buttons.

It can cause malfunctions.

>

Caution

Remove foreign materials between the grill and

the case by using a cotton swab.

,

Note

Front panel

Getting Started 9

Getting Started

1

A

USB (Service only)

S/W download connector

B

LAN port

Connect to a router.

C

PORTABLE IN connector

Connect portable device.

D

OPTICAL IN connector

Connect to an optical device.

E

HDMI OUT (TV ARC)

Connect to HDMI IN (ARC) on TV.

F

HDMI IN (1) / HDMI IN (2)

Connect to device with HDMI OUT.

Rear panel

Getting Started10

Getting Started

1

Useful functions for using the unit

Function Description To do Do this

TV Remote On/

Off

(Page 33)

It allows you to control the

volume of this unit by your TV

remote control even by other

company’s product.

Initial setting of this function

was set to on.

ON Press and hold AV SYNC on the remote

control for about 3 seconds and then press

the button again.

OFF Press and hold AV SYNC on the remote

control for about 3 seconds and then press

the button again.

BT Lock On/Off

(Page 33)

It allows you to connect a

Bluetooth device only on

Bluetooth and LG TV functions.

Initial setting of this function

was set to off.

ON Press and hold AUTO POWER on the

remote control for about 2 seconds in

Bluetooth function and then press the

button again.

OFF Press and hold AUTO POWER on the

remote control for about 2 seconds in

Bluetooth function and then press the

button again.

Auto Power

On/Off

(Page 35)

It allows the unit to turn on

and off automatically by input

signals:

Optical, LG TV, Bluetooth or “LG

Wi-Fi Speaker” app.

Initial setting of this function

was set to on.

ON Press AUTO POWER on the remote control

and then press the button again.

OFF Press AUTO POWER on the remote control

and then press the button again.

BT Standby

On/Off

(Page 38)

It allows the unit to switch

to standby mode while

maintaining Bluetooth

connection.

ON Set the volume to a minimum in advance.

Press and hold

p

on the unit and

J

on

the remote control for about 3 seconds and

then press the button again.

OFF Set the volume to a minimum in advance.

Press and hold

p

on the unit and

J

on

the remote control for about 3 seconds and

then press the button again.

Network

Standby On/

Off

(Page 38)

It allows the unit to switch

to standby mode while

maintaining a network

connection.

ON Press

1

on the unit or

1

on the remote

control.

OFF Press

1

on the unit or

1

on the remote

control for about 3 seconds.

Surround On/

Off

(Page 17)

It allows you to enjoy surround

sound with rear speakers.

Initial setting of this function

was set to off.

ON Press and hold AUTO VOL on the remote

control for about 2 seconds and then press

the button again.

OFF Press and hold AUTO VOL on the remote

control for about 2 seconds and then press

the button again.

Getting Started 11

Getting Started

1

Installing the sound bar

You can hear the sound by connecting the unit to the

other device: TV, Blu-ray disc player, DVD player, etc.

Place the unit in front of the TV and connect it to the

device you want. (Pages 21 - 28)

You can place the wireless subwoofer anywhere in

your room. But it is better to place the subwoofer

near the main unit. Turn it slightly toward the center

of the room to reduce the wall reections.

y

For best performance of wireless connection

such as Bluetooth or wireless subwoofer,

do not install the unit on Metallic furniture

because wireless connection communicates

through a module positioned on the bottom

of the unit.

y

Be careful not to make scratches on the

surface of the Unit /Subwoofer when

installing or moving them.

>

Caution

For the convenient button usage, it is

recommended to take some distance between

the soundbar and your TV when you install the

sound bar.

,

Note

Mounting the main unit

on a wall

You can mount the main unit on a wall.

Because it is difcult to make a connection after

installing this unit, you should connect the cables

before installation.

>

Caution

Preparation materials

Unit

Wall bracket install guide

Screws

Screws (A)

Wall plug

Wall bracket

(Not supplied)

Getting Started12

Getting Started

1

1. Match the TV’s BOTTOM EDGE of Wall bracket

install guide with the bottom of TV and attach to

the position.

2. When you mount it on a wall (concrete), use the

wall plugs. You should drill some holes. A guide

sheet (Wall bracket install guide) is supplied to

drill. Use the sheet to check the point to drill.

3. Remove the Wall bracket install guide.

4. Fix the brackets with screws (A) as shown in the

illustration below.

Screws (A) and Wall Plugs are not supplied for

mounting the unit. We recommend the Hilti

(HUD-1 6 x 30) for the mounting.

,

Note

5. Put the unit on the brackets to match screw

holes on the bottom of the unit.

6. Fix the unit with the screws firmly.

To detach the unit, perform it in reverse order.

,

Note

y

Do not install this unit upside down. It can

damage the parts of this unit or be the cause

of personal injury.

y

Do not hang onto the installed unit and avoid

any impact to the unit.

y

Secure the unit rmly to the wall so that it

does not fall off. If the unit falls off, it may

result in an injury or damage to the product.

y

When the unit is installed on a wall, please

make sure that a child does not pull any of

connecting cables, as it may cause it to fall.

>

Caution

Getting Started 13

Getting Started

1

Positioning the speakers

(Optional)

For the best surround sound, place the speakers as

shown below.

The illustration above may differ from actual

units.

,

Note

2 Connecting

Connecting14

Connecting

2

Organizing cables

You can organize the cable with cable ties.

1. Hold the cables together with cable ties as shown

below.

2. Tighten cable ties.

After all connections are completed, you can

arrange cables as needed.

,

Note

Wireless subwoofer

and rear speaker (Sold

Separately) connection

Wireless subwoofer connection

LED indicator of wireless subwoofer

LED Color Status

Green

(Blink)

The connection is trying.

Green The connection is completed.

Red The wireless subwoofer is in

standby mode or the connection

is failed.

Off (No

display)

The power cord of wireless

subwoofer is disconnected.

Setting up the wireless subwoofer for

the first time

1. Connect the power cord of the sound bar and the

wireless subwoofer to the outlet.

2. Turn on the sound bar. The sound bar and

the wireless subwoofer will be automatically

connected.

Connecting 15

Connecting

2

Manually pairing wireless subwoofer

When your connection is not completed, you can

check red LED on the wireless subwoofer and the

wireless subwoofer does not make sound. To solve

the problem, follow the steps below.

1. Press Pairing button on the rear of the wireless

subwoofer.

Pairing

- The green LED on the rear of the wireless

subwoofer blinks quickly.

(If the green LED does not blink, press and hold

the Pairing button.)

2. Turn on the sound bar.

3. Pairing is completed.

- The green LED on the rear of the wireless

subwoofer turns on.

y

It takes a few seconds (and may take longer)

for the main unit and the subwoofer to

communicate with each other and make

sounds.

y

The closer the main unit and the subwoofer,

the better sound quality. It is recommended

to install the main unit and the subwoofer as

close as possible and avoid the cases below.

- There is an obstacle between the main unit

and the subwoofer.

- There is a device using same frequency

with this wireless connection such as

a medical equipment, a microwave or a

wireless LAN device.

- Keep the sound bar and the subwoofer

away from the device (ex. wireless router,

microwave oven, etc.) over 1 m to prevent

wireless interference.

!

1 m

,

Note

Connecting16

Connecting

2

Rear speakers connection (Sold

Separately)

Connecting the rear speakers

1. Connect the black stripe wire to the terminal

marked - (minus) and the other end to the

terminal marked + (plus).

2. Connect the wireless receiver and the rear

speakers (right, left) with the speaker cables.

Color Position

Grey Rear right

Blue Rear left

You need to purchase the wireless rear speakers

kit (SPK8-S) to enjoy surround sound.

,

Note

y

Use the speaker supplied with this unit

only. Using any other speaker may cause

malfunction.

y

Be sure to match the speaker cable to the

appropriate terminal on the components: +

to + and – to –. If the cables are reversed, the

sound will be distorted and will lack bass.

>

Caution

LED indicator of wireless receiver

LED Color Status

Yellow - green

(Blink)

The connection is trying.

Yellow - green The wireless receiver is receiving

the signal from the sound bar.

Red The wireless receiver is in standby

mode.

Off

(No display)

The power cord of wireless

receiver is disconnected.

Setting up the wireless receiver for the

first time

1. Connect the power cord to the wireless receiver

to the outlet.

2. Turn on the main unit : The sound bar and wireless

receiver will be automatically connected.

- Yellow - green LED on the wireless receiver

turns on.

Connecting 17

Connecting

2

Manually pairing wireless receiver

When your connection is not completed, you can

see the red LED on the wireless receiver and rear

speakers are not made sound. To solve the problem,

follow the below steps.

1. Press PAIRING button on the rear of the wireless

receiver.

- The yellow - green LED on the wireless receiver

blinks quickly.

2. Turn on the main unit

3. Paring is completed.

- The yellow - green LED on the wireless receiver

turns on.

Surround sound

You can enjoy magnicent surround sound for all the

input sound source with rear speakers.

If you turn on the surround function, the whole

speaker outputs sound.

When you turn off the surround function, the

speakers output sound as an original input sound

channel.

To turn on surround function, press and hold AUTO

VOL on the remote control for about 2 seconds

and press it once again while “OFF - SURROUND” is

scrolled.

To turn off surround function, press and hold AUTO

VOL on the remote control for about 2 seconds

and press it once again while “ON - SURROUND” is

scrolled.

Connecting18

Connecting

2

Surround function ON

Sound Effect Input

Output

No rear speakers Rear speakers connected

ASC

2.0 Ch

5.1 Ch

7.1 Ch or more

BASS BLAST

or

BASS BLAST+

2.0 Ch

5.1 Ch

7.1 Ch or more

STANDARD

2.0 Ch

5.1 Ch

7.1 Ch or more

MOVIE

2.0 Ch

5.1 Ch

7.1 Ch or more

MUSIC

2.0 Ch

5.1 Ch

7.1 Ch or more

Connecting 19

Connecting

2

Surround function OFF

Sound Effect Input

Output

No rear speakers Rear speakers connected

ASC

2.0 Ch

5.1 Ch

7.1 Ch or more

BASS BLAST

or

BASS BLAST+

2.0 Ch

5.1 Ch

7.1 Ch or more

STANDARD

2.0 Ch

5.1 Ch

7.1 Ch or more

MOVIE

2.0 Ch

5.1 Ch

7.1 Ch or more

MUSIC

2.0 Ch

5.1 Ch

7.1 Ch or more

Connecting20

Connecting

2

How to Affix the Ferrite Core

Ferrite core may not be provided depending on each

nation’s regulations.

Affix the Ferrite Core for speaker

cables

You must afx a ferrite core in order to reduce or

eliminate electrical interference.

1. Pull the stopper [a] of the ferrite core to open.

2. Wind the speaker cables around the ferrite core

twice.

3. Close the ferrite core until it clicks.

y

If there is a strong electromagnetic wave

product nearby, interference may occur. Put

the main unit and wireless receiver away from

there.

y

The wireless receiver will automatically switch

to standby mode in a few minutes after the

sound bar is turned off.

When the wireless reciever is in standby

mode, the LED will turn on in red.

y

When you turn on the sound bar, the wireless

receiver will turn on and the LED will change

to yellow - green and then the rear speakers

makes sound within a few seconds.

y

It takes a few seconds (and may take longer)

for the main unit and Wireless Receiver to

communicate with each other.

y

Use the rear speaker at least 30 cm away from

either TV screen or PC monitor.

y

When the wireless receiver is being

connected or disconneced with the main unit,

output sound is maybe interrupted.

y

Set the distance between the sound bar and

the wireless receiver as close as possible and

keep them away from the device (ex. wireless

router, microwave oven, etc.) over 1 m to

prevent wireless interference.

!

1 m

,

Note

Page is loading ...

LG SK10Y User manual

Other documents