Encore 42K17Z Z-Series Owner's manual

Brand: Encore

Model: 42K17Z Z-Series

Category: Tractor

Type: Owner's manual

OPERATORS

MANUAL

4 2 K 1 7 Z

ENCORE

Your mower is only as safe as the

operator!

Operator carelessness or error may result

in serious bodily injury. Improper

maintenance of the machine may also

result in injury. Please read and follow

these instructions on Safe Operation and

be certain that anyone using this mower

fully understands and follows these

instructions.

1. Familiarize yourself with the controls and know

how to stop the rider and mower deck quickly.

2. Inspect your work area carefully. Remove debris

from the area to be cut. Keep all bystanders away

from the mowing area.

3. Avoid contact with moving parts. Keep hands and

feet clear of the mower deck.

4. Never direct the discharge of material toward

bystanders nor allow anyone near the machine

while in operation.

5. The machine is not intended for highway or street

use. Never carry passengers!

6. Never tamper with safety devices or guards. If a

guard or safety device is damaged or removed,

replace it before operating the rider.

7. Handle gasoline carefully. Use an approved

gasoline container. Fill the fuel tank, to within 1"

from the neck, with good quality unleaded gaso-

line.

8. Drive levers must be in the Neutral position and

the Blade Clutch must be disengaged before

starting engine.

9. Operator must wear proper shoes and clothing,

which may include safety glasses and ear protec-

tion.

10. Mow only during daylight hours or under very good

artificial light.

11. The safety shield over the Grass Discharge area

must always be bolted in place and in the DOWN

position unless the Grass Catcher is being used.

12. If a solid object has been hit by the blades stop the

machine and check for damage. Repair or replace

any damaged/broken part prior to restarting the

engine.

13. To avoid burns, DO NOT TOUCH the engine or

muffler immediately after operation.

14. Disengage blades when transporting and when

crossing walks and gravel roads.

15. Do NOT mow close to drop-offs, deep ditches or

other hazards. Do NOT stop or start suddenly

when going uphill or downhill. Mow up and down

the face of steep slopes; NEVER mow across the

face. If a steep hill must be ascended, BACK up

the hill, drive forward when descending.

16. Reduce speed and exercise extreme caution on

slopes and in sharp turns to prevent tipping or loss

of control. Be especially cautious when changing

direction on slopes.

17. The Encore Z’s is NOT designed for towing. Only

factory approved Grass Collection Systems are

permitted.

 WARNING:

DO NOT allow children to operate the

machine. DO NOT allow any adult to operate

the machine without proper instruction.

 CAUTION:

Never add fuel to the tank while the engine is

running or hot. ALWAYS WAIT at least five

minutes before refueling and REFUEL WITH THE

ENGINE OFF. KEEP FUEL AWAY FROM

SPARKS OR FLAMES. WIPE AWAY any fuel

spillage BEFORE starting unit. Never fill the fuel

tank indoors. Wipe up any spilled gasoline.

Gasoline is highly flammable - NO SMOKING.

ENCORE

ASSEMBLY INSTRUCTIONS for

42B350Z ; 42K450Z ; 48B450Z ;

48K550Z ; 52B550Z ; 52K650Z.

Remove unit from crate, taking care to re-

move inner boxes and the small parts box.

1. Remove deflector chute, bolt bag and

operator’s manual from main assembly.

2. Open bolt bag and lay out bolts:

(8) – 5/16 X 3/4 HHCS

(2) – 5/16 X 1 HHCS

(2) – 5/16 Nyloc Nuts

(4) – 5/16 Whizlock Nuts

(4) – 5/16 Lock Washers

3. Take the 2 - 5/16 X 1 HHCS and 2 – 5/16

Nyloc nuts and bolt deflector into place.

CRATE REMOVAL INSTRUCTIONS

To remove the mower from the crate, take the

top frame off the mower pallet.

Assemble the unit as instructed by the As-

sembly Instructions.

After fueling and oiling the engine, hook up

the battery.

Before Operating - Reminders

Fill engine crankcase as per engine

manufacturer’s manual.

ENGINE DOES

NOT HAVE OIL IN CRANKCASE FROM

THE FACTORY. Add proper fuel to fuel tank,

open value.

The battery is now a gel-cell and will not

require acid.

Before hooking up the ground wires make

sure that the engine has been filled to the

proper level with oil.

If battery will not turn the engine over after

hooking the wires up it may require a charge

for 15 to 20 minutes.

Raise the unit slightly and place a board

under each rear wheel.

With the deck in the raised position start the

unit and drive it off the pallet.

Once you are familiar with the contents of this

manual you are ready to mow with the finest

mower built!

Note: Make sure to

connect both

ground wires.

ENCORE

4. Take the 4 – 5/16 X 3/4 HHCS and

4 – Lock Washers and fasten seat to the

seat plate.

5. Take the remaining bolts and whizlocks

nuts and bolt control levers onto the

outsides of the mount angles, adjusting

them according to operator comfort.

6. Attach the wire harness to the seat switch.

ASSEMBLY INSTRUCTIONS for

42K17Z ; 48K19Z ; 52K21Z.

Remove unit from crate, taking care to

remove inner boxes and the small parts box.

1. Remove deflector chute, bolt bag and

operator’s manual from main assembly.

2. Open bolt bag and lay out bolts:

(4) – 5/16 X 3/4 HHCS

(2) – 5/16 X 1 HHCS

(4) – 5/16 X 1 3/4 HHCS

(2) – 5/16 Nyloc Nuts

(4) – 5/16 Whizlock Nuts

(4) – 5/16 Lock Washers

3. Take the 2 - 5/16 X 1 HHCS and 2 – 5/16

Nyloc nuts and bolt deflector into place.

4. Take the 4 – 5/16 X 3/4 HHCS and

4 – Lock Washers and fasten seat to the

seat plate.

5. Take the remaining bolts and whizlocks

nuts and bolt control levers onto the

outsides of the handle mounts, adjusting

them according to operator comfort.

6. Attach the wire harness to the seat switch.

STARTING ENGINE

Throttle control, ignition switch and choke

control are located between motion control

levers on the front panel under the front of the

seat.

Because of a built-in safety interlock system,

your machine will not start unless the seat is

occupied.

TO START ENGINE: occupy seat, set park

brake, leave the motion control levers swung

out, move throttle control lever halfway to

operating position. Turn ignition key to start

position to engage starter, release the key

when engine starts. Ignition switch is spring

loaded and will return to run position auto-

matically.

Slowly return choke to run position once the

engine has started.

STOPPING ENGINE

TO STOP ENGINE: move throttle lever to

idle position and turn ignition key to “OFF”

position. If engine has been working hard or

is hot, allow engine to idle for a short period

of time before turning off key. This practice

will help cool engine before stopping.

IN CASE OF EMERGENCY engine may be

stopped by turning ignition key to “OFF”

position.

 CAUTION:

Always remove the key and set the parking

brake when leaving the machine unattended,

even for just a few minutes.

PREVENT ACCIDENTS: Do not give

children or unauthorized persons an opportunity

to operate this machine.

SAFETY INTERLOCK SYSTEM

Your Encore Rider is equipped with a Safety

Interlock System that is designed to help

prevent possible serious injuries. Under-

standing and maintaining this system is vital,

for maximum safe operation.

TO START ENGINE:

1. Blades (PTO) must be “OFF”.

2. Control levers in neutral

(swung out).

3. Park Brake “ON”.

4. Operator in seat.

THE ENGINE WILL KILL IF:

1. The operator leaves the seat with:

a. The control levers out of neutral

(swung in).

b. The blades on (PTO).

c. The park brake is “OFF”.

d. All the above.

ENCORE

 WARNING:

THE ENGINE EXHAUST FROM THIS

PRODUCT CONTAINS CHEMICALS

KNOWN IN THE STATE OF CALIFORNIA

TO CAUSE CANCER, BIRTH DEFECTS

OR OTHER REPRODUCTIVE HARMS.

MOWING SPEED

The Encore Rider is designed to operate

most efficiently at maximum blade speeds.

The running speed of the machine should

allow the mower blades to maintain this

maximum speed while mowing across turf.

Use a slower ground speed for cutting tall

grass, grass which is heavy with moisture, or

when mowing uphill. If ground speed is too

fast, or blade speed is too slow, mowing will

be uneven because mower blades will not be

able to lift grass into cutting position as the

mower passes.

Throttle control regulates speed of engine as

measured in RPM. This control SHOULD

NOT be used to control ground speed.

MAINTENANCE AND SERVICE

1. Do not adjust mower or change attach

ments unless the engine has been

stopped and the key has been removed.

2. Good maintenance, wiping up gasoline

and oil spills, will reduce potential fire

hazards.

3. To insure that the mower will remain in

safe operating condition, check and

tighten all bolts, nuts and screws.

Especially make certain the blade bolt/

nuts are always tightened properly.

4. Never adjust governor on engine to a

faster speed. The engine manufacturer

adjusts the engine RPM to the proper

setting.

5. Allow time for the engine to cool down

prior to storing mower. Do not store

mower or gasoline near any open flame

or where gasoline fumes may be ignited.

6. Always replace worn or broken parts with

genuine Encore repair parts purchased

from an authorized Encore dealer. Using

anything other than Encore repair parts

may void all Encore factory warranties.

OIL AND FILTER for 42B350Z ;

42K450Z ; 48B450Z ; 48K550Z ;

52B550Z ; 52K650Z.

Change the hydraulic system filter and reser-

voir oil between 50 – 100 hours the first time,

every 500 hours thereafter. The hydraulic

filter is located under the right fender.

 CAUTION:

DO NOT SPILL OIL OR GREASE ON BELTS.

SAFETY INTERLOCK SYSTEM

(continued..)

2. The park brake is set before the

control levers are in neutral

(swung out)

CORRECT TRANSMISSION

OPERATION TO GO FORWARD

OR REVERSE

The Encore Rider is equipped with a separate

pump and wheel motor for each wheel and

are controlled with “Motion Control Levers” ,

one for each wheel.

 To go FORWARD, push both levers

forward evenly.

 To go in REVERSE, pull back on both

levers evenly.

 To CHANGE DIRECTION, slowly

move levers to neutral and move the

lever forward in the direction you want

to go.

 The further the levers are moved away

from the neutral position, the faster the

machine will travel. To turn the Rider

left or right, slow the speed of the

wheel in the direction you want to turn.

 To STOP the Rider, return both levers

evenly to the neutral position.

ENCORE

Follow the installation instructions printed on

the filter. Use only a high quality 20W50

rated engine oil. NOTE: Refer to the engine

manual for engine lubrication recommen-

dations.

OIL AND FILTER for 42K17Z ;

48K19Z ; 52K21Z.

Change the hydraulic system filter at 250

hours. The hydraulic filter is located on the

hydraulic tank. Note: Clean filter area before

remounting to prevent contampuation.

Change hydraulic oil in the reservoir yearly.

Use only a high quality Mobile 1 - 15w50

rated oil. NOTE: Refer to the engine

manual for engine lubrication recommen-

dations.

TIRE PRESSURE

This vehicle has been designed to achieve

maximum operator comfort and ride. This

cannot be achieved without proper tire pres-

sure. A low pressure gauge is required to

check the front tires.

Front Tires - 14 PSI

Rear Tires - 20 PSI

BATTERY

For maintenance of acid filled battery the

electrolyte level above plates in each cell by

adding distilled water as necessary. The best

time to add water is just prior to operating the

mower so water will mix with the solution. Do

NOT over fill battery: Electrolyte solution is

NOTES:

The Encore Rider is driven and steered by

the rear wheels.

REAR TIRE CIRCUMFERENCE DIRECTLY

EFFECTS THE TRACKING OF THE

MACHINE.

If the machine will not drive in a straight line,

check air pressure and adjust accordingly.

 CAUTION:

When servicing the battery or any other part

of the electrical system, or if the battery must

be removed for any reason, always, discon-

nect negative (ground) cable FIRST and re-

connect it LAST to avoid possibility of electri-

cal shorts.

At temperatures below 32° F (0° C), full charge

state must be maintained to prevent cell elec-

trolyte from freezing and causing permanent

battery damage.

 CAUTION:

Batteries produce flammable hydrogen gas.

Avoid creating sparks and open flames and

do not smoke when working near batteries.

Battery electrolyte solution is poisonous and

can be injurious to eyes, skin and clothing.

IN THE EVENT OF AN ACCIDENT: Flush

affected area immediately with a solution of

one part baking soda to four parts water. If

baking soda is not readily available, flush

affected area with water. Notify physician

immediately.

corrosive and over filling can cause damage

to surrounding metal parts. Battery should be

maintained at 1.265 gravity charge. When

replacing battery after servicing, take care to

reconnect cables exactly the way they were

before removing the battery.

The gel-cell battery is maintenance free.

For longest service life, battery should be

kept clean by wiping it off with a paper towel.

Any corrosion around battery should be

removed by applying a solution of one part

baking soda to four parts water. A light coat-

ing of grease or petroleum jelly may be ap-

plied to all exposed terminal surfaces to

prevent corrosion.

ENCORE

BELT ADJUSTMENT

Remove key from the ignition switch. The

deck drive belt, which may be accessed by

removing the deck plate, (see fig.1) has a

turnbuckle assembly to adjust spring tension.

Spring tension should be maintained at 4" of

spring stretch measuring the spring coils. By

turning the turnbuckle clockwise it will in-

crease tension, counter-clockwise will de-

crease tension.

When installing a belt refer to fig. 2 as to the

route of the belt.

 CAUTION:

DO NOT over grease housings – it will push

seals out of bearings.

BELT TENSION

TURNBUCKLE

Fig. 1 - Turnbuckle Location

TENSION

IDLER

BLADE

IDLER

ENGINE

PULLEY

Fig. 2 - Mower Deck Belt Layout

LUBRICATION for 42B350Z ;

42K450Z ; 48B450Z ; 48K550Z ;

52B550Z ; 52K650Z.

The following recommendations on lubrica-

tion should be adhered to. Environmental

conditions may be cause to vary frequency.

Before each use:

 Clean engine chaff screen

 Check engine oil and tire

Every 100 hours:

 Lubricate chassis

 Lubricate front wheel

 Lubricate drive and pump control pivot

points

 Check belt tension

Every 200 hours:

 Lubricate cutter housings

(1 to 2pumps)

LUBRICATION for 42K17Z ;

48K19Z ; 52K21Z.

There are 5 grease points on the Z42, 48 and

52. One on each caster, one on the caster

swivel and one on the foot pedal pivot. These

are all pre-greased from the factory. Environ-

mental conditions may be cause to vary

frequency.

Before each use:

 Clean engine chaff screen

 Check engine oil and tire pressure

Every 40 hours:

 Lubricate Casters (3 Pumps)

 Lubricate Deck Height Foot-Pivot

(1 Pump)

Every 100 hours:

 Lubricate Caster Swivels (3 Pumps)

 Lubricate drive and pump control pivot

points

 Check belt tension

ENCORE

NEUTRAL ADJUSTMENT - DRIVE

1. Raise the rear wheels of the rider off of the

ground. Safely block the frame in this posi-

tion so it is secure.

2. With the operator in the seat, start and run

the engine, leaving the control levers in the

neutral position. Release the park brake.

Check the rear wheels for neutral creep (any

rotation).

3. Stop engine, place park lever into park

position, flip up seat, and loosen jam nut on

adjustable pump link (fig. 3) on the same side

as the wheel that creeps (rotates). With a 5/

32" Hex Allen Wrench, adjust pump link from

the top. For a wheel that is rotating forward

turn the wrench clockwise – for a wheel that

rotates in reverse motion turn wrench

counter-clockwise. Never adjust link more

than 2 full turns at any one time. Retighten

jam nut and start engine.

4. If wheel still creeps repeat procedure in

step 3.

5. After final adjustment is made (make sure

that the jam nut is secure on pump link), take

unit for a test drive to check tracking.

TRACKING for

42B350Z ; 42K450Z ; 48B450Z ;

48K550Z ; 52B550Z ; 52K650Z.

1. Return the wheels to the ground and drive

the mower to check tracking at low and full

speed.

2. If the pumps are properly neutralized,

intermediate speed tracking is only affected

by tire size and/or tire pressure.

3. Full speed tracking is determined by the

stop bolts at the bottom of each vertical pump

link (see fig. 3). You may speed up or slow

down a fast or slow pump motor by either

shortening or lengthening the stop bolt.

TRACKING for

42K17Z ; 48K19Z ; 52K21Z.

To adjust the tracking there is a stop bolt

located on the bottom side of the steering

control. (See Fig. 4)

To adjust tracking simply loosen the lock nut

on the stop bolt and turn bolt clockwise to

increase speed or counter clockwise to de-

crease speed.

DRIVE ADJUSTMENTS

Steering and motion controls should be

uniform in all forward and reverse speeds.

Levers should automatically return to neutral

when released.

5/32 HEX

ADJUSTABLE PUMP LINK

JAM NUT

VERTICAL PUMP LINK

STOP BOLT

Fig. 3 - Neutral link area of pump

ENCORE

To test drive operations:

 Check air pressure in tires. Equal tire

pressure is critical for proper drive

opeation.

 Check linkage for excessive play.

• Raise rear of Rider until rear wheels

are off the ground. Safely block the

frame in this position.

• Put control levers in neutral lock

position (control levers swung

outward).

• Start engine.

Wheels should not rotate. If one or both rear

wheels are turning, perform procedures under

“Neutral Adjustments” for side(s) that wheel

turns (fig. 3).

DECK HEIGHT ADJUSTMENT for

42B350Z ; 42K450Z ; 48B450Z ;

48K550Z ; 52B550Z ; 52K650Z.

The cutting height can be adjusted from 2 to

5 inches in approximately 1/4 inch incre-

ments. The height may be selected by simply

moving the deck height adjustment lever to

desired cutting height.

 CAUTION:

TURN OFF ENGINE BEFORE MAKING ANY

ADJUSTMENTS.

2 to 2 1/2 inches

each notch

approx. = 1/4"

4 to 4 1/2 inches

RAISE

LOWER

DECK HEIGHT ADJUSTMENT LEVER

DECK HEIGHT ADJUSTMENT for

42K17Z ; 48K19Z ; 52K21Z.

Mower heights can be adjusted by pushing

the foot pedal and by depressing the height of

cut pin and removing it. Select cutting height

and set pin accordingly.

BLOCK OF WOOD

FIG. 5

BLADES

When removing blades, block front end up or

run front wheels onto ramps. Stop engine,

remove key from the ignition switch, and

apply park brake. To remove, simply hold

blade bolt on bottom of the cutter housing

(See Fig. 5) and turn nut counter-clockwise.

Reverse procedure to reinstall. Blade bolts

should be torqued to 110 - 120 ft.lbs.

Note: Deck spring washer should always be

cup side up or cup side to blade to insure

proper torque on the blades.

ENCORE

 WARNING:

NEVER RUN THE ENGINE IF THE BAT-

TERY IS REMOVED OR IF THE BATTERY

IS NOT CONNECTED TO THE CHARGING

SYSTEM. SERIOUS DAMAGE TO

CHARGING SYSTEM COMPONENTS

MAY RESULT.

DECK LEVELING ADJUSTMENT

Before checking the deck level makes sure

that tire pressures are inflated to the proper

level. Begin by setting the deck to a fixed

position and pointing the blades to the front

edge of the deck.

ELECTRICAL

The fuse box is located under the seat on a

panel mounted to the seat frame. There are

two (2) fuses that run the system, the top

fuse, which is a 20 amp, is the main fuse.

The second, a 15 amp fuse, takes care of the

electric clutch. The third and fourth slots are

blank extras. If there is a recurring fuse

failure, check the electrical system for a

short.

ELECTRICAL DAIGRAMS

Z Series riders electrical diagrams are on

page 10, 11 and 12 for the various models.

 CAUTION:

Mower blades are sharp and can cut you

during blade maintenance or adjustment.

Use suitable covering over cutting edges of

blades to prevent bodily harm.

To obtain optimum mowing results, mower

blades should be kept sharp and well bal-

anced. File or grind blades evenly. Take

care to retain angle of original cutting edge.

CHARGING SYSTEM

An alternator is used to charge the battery.

The alternator charging system normally

requires no service other than periodically

checking that all exposed wiring and electrical

connections on the machine are clean, tight

and in good condition.

Proper polarity is critical with an alternator

equipped charging systems. Always discon-

nect battery cable (negative) before working

on any part of the electrical system. Verify all

components are connected correctly before

reconnecting ground cable (negative) or

damage to alternator system components will

result.

Measuring from the blade to the ground on

each side of the deck will give the best read-

ing. To adjust deck position loosen the bolt on

the deck hanger bracket and move bolt in the

slot either up or down depending which way

you need to move the deck. You should

always maintain at least a 1/8 inch of deck

pitch from front to back. Also all four chains

must support the deck equally or must have

equal tension on them.

ENCORE

42B350Z , 48B450Z , 52B550Z

423078 WIRE HARNESS

ELECTRICAL DRAWING

GROUND TO ENGINE

TO BATT. GROUND

TO BATT. POS.

BLACK 18 GA.

BLACK 14 GA.

RED /BLACK STP. 18 GA.

YELLOW 16 GA.

RED 14 GA.

GREEN 18 GA.

PURPLE 18 GA.

ORANGE 18 GA.

DK. BLUE 18 GA.

WHITE 16 GA.

FUSE

BLOCK

IGNITION SWITCH

NEUTRAL SWITCH

CLUTCH

SWITCH

SEAT

SWITCH

ENGINE KILL

BLACK 16 GA.

BROWN 18 GA.

BLACK / WHITE 18 GA.

DK. BLUE 18 GA.

LT. BLUE 14 GA.

RED 12 GA.

ENGINE FUEL

SOLENOID

ENGINE

CHARGING

ORANGE 12 GA.

WIRE JUNCTION

HOUR METER

MODULE

CONN.

PARK BRAKE

SWITCH

CLUTCH

CONN.

STARTER RELAY

RED /BLACK STP. 18 GA.

ENCORE

STARTER

RELAY

15 AMP FUSE

20 AMP FUSE

RED 14 GA.

LT. BLUE 14 GA.

BROWN 18 GA.

BLACK 16 GA.

GREEN 18 GA.

PARK BRAKE

SWITCH

WIRE

JUNCTION

RED 12 GA.

BLACK / WHITE 18 GA.

DK. BLUE 18 GA.

ENGINE KILL

RED /BLACK STP. 18 GA.

TO BATT. POS.

ORANGE 18 GA.

ENGINE

CHARGING

ENGINE FUEL

SOLENOID

TO BATT. GROUND

BLACK 16 GA.

42K450Z , 48K550Z , 52K650Z

423237 WIRE HARNESS

ELECTRICAL DRAWING

RED /BLACK STP. 18 GA.

IGNITION SWITCH

FUSE

BLOCK

WHITE 16 GA.

RED 12 GA.

LT. BLUE 14 GA.

ORANGE 12 GA.

YELLOW 16 GA.

BLACK 14 GA.

BLACK 18 GA.

CLUTCH

CONN.

GROUND TO ENGINE

CLUTCH

SWITCH

NEUTRAL

SWITCH

GREEN 18 GA.

LT. BLUE 14 GA.

BROWN 18 GA.

MODULE

CONN.

SEAT

SWITCH

PURPLE 18 GA.

GREEN 18 GA.

DK. BLUE 18 GA.

HOUR METER

ENCORE

RED 14 GA.

STARTER

RELAY

BLACK 16 GA.

BROWN 18 GA.

LT. BLUE 14 GA.

PARK BRAKE

SWITCH

RED 12 GA.

ENGINE FUEL

SOLENOID

ENGINE

CHARGING

ORANGE 18 GA.

TO BATT. POS.

RED /BLACK STP. 18 GA.

ENGINE KILL

DK. BLUE 18 GA.

BLACK 16 GA.

O BATT. GROUND

20 AMP FUSE

15 AMP FUSE

WIRE JUNCTION

42K17Z , 48K19Z , 52K21Z

423351 WIRE HARNESS

ELECTRICAL DRAWING

ORANGE 12 GA.

LT. BLUE 14 GA.

RED 12 GA.

WHITE 16 GA.

FUSE

BLOCK

IGNITION

SWITCH

RED /BLACK STP. 18 GA.

YELLOW 16 GA.

GREEN 18 GA.

GROUND TO ENGINE

NEUTRAL

SWITCH

CLUTCH

CONN.

BLACK 18 GA.

BLACK 14 GA.

BLACK / WHITE 18 GA.

MODULE

CONN.

BROWN 18 GA.

LT. BLUE 14 GA.

GREEN 18 GA.

CLUTCH

SWITCH

HOUR METER

DK. BLUE 18 GA.

GREEN 18 GA.

PURPLE 18 GA.

SEAT

SWITCH

ENCORE

BDP-10L VARIABLE PUMP – SUPPORT SYSTEM

TRANSMISSION HYDRAULIC SUPPORT SYSTEM

The charge pump incorporated into the BDP-

10L units supplies fluid to keep the closed

loop charged, preventing cavitations and

providing cooling oil flow for the system. An

inlet filter is required to insure that only clean

fluid enters the system. The charge relief

valve is designed to maintain the charge

pressure at 25 to 70 PSI at 3600 RPM input

speed.

Since either of the main hydraulic passages

can be at high pressure, two (2) charge check

valves are used to direct make-up fluid into

the low-pressure side of the closed loop.

These check valves are located in the pump

end cap.

FILTER

RESERVOIR

CASE

DRAIN

INPUT

SHAFT

VARIABLE

SWASHPLATE

CYLINDER

BLOCK

ASSEMBLY

VARIABLE

DISPLACEMENT

PUMP

COOLING

ORIFICE

CHARGE

PUMP

BYPASS

VALVE

CHARGE

RELIEF

VALVE

CHECK

VALVE

LINE B

LINE A

CHECK

VALVE

 CAUTION:

 The loss of hydrostatic driveline power in

any mode of operation may cause a loss of

hydrostatic braking capacity. A braking system,

redundant to the hydrostatic transmission must,

therefore, be provided which is adequate to stop

and/or hold the system should the condition

develop.

 Certain service procedures may require the

vehicle/machine to be disabled (wheels raised

off the ground, work function disconnect, etc.)

while performing them in order to prevent injury

to the technician and bystanders.

 CAUTION:

 Use caution when dealing with hydraulic

fluid under pressure. Escaping hydraulic fluid

under pressure can have sufficient force to

penetrate your skin causing serious injury. This

fluid may also be hot enough to burn. Serious

infection or reactions can develop if proper

medical treatment is not administered

immediately.

 Some cleaning solvents are flammable. To

avoid possible fire, do not use cleaning solvents

in an area where a source of ignition may be

present.

ENCORE

CONTROLS AND FEATURES - BDP-10L VARIABLE PUMP

Direct Displacement Control

The direct-proportional displacement control

(DDC) provides a simple method of control.

Movement of the swashplate control shaft

produces a proportional swashplate

movement and change in pump flow and/or

direction.

If difficulties are encountered with the control,

inspect the connection of the control linkage

to the swashplate control shaft to insure that

the linkage is properly attached. The vehicle/

machine control system determines the

neutral position of the linkage.

Charge Pumps

A fixed displacement geroter type charge

pump is provided as part of the BDP-10L.

Bypass Valve

In some application, it is desirable to move

the machine for short distances at low speeds

without operating the engine. A bypass valve

allows oil to be routed from one side of the

pump/motor circuit to the other, thus allowing

the motor to turn with little resistance.

The BDP variable pumps utilize a screw type

bypass valve which is fully open when

unscrewed two (2) turns maximum. The

bypass valve must be fully closed during

normal vehicle operation.

 WARNING:

OPENING THE BYPASS VALVE WILL

RESULT IN A LOSS OF HYDROSTATIC

BRAKING CAPACITY. TAKE

PRECAUTIONS TO PREVENT MACHINE

MOVEMENT WHEN OPENING THE

VALVE.

BDP-10L Variable Pump with

Charge Pump

BDP-10L Pump

ENCORE

START UP MAINTENACE - BDP-10L VARIABLE PUMP

Fluids

Fluids used with Hydro-Gear product should

be carefully selected with assistance from a

reputable supplier.

Typically, an API classification SG/CD engine

oil is used with a viscosity range equivalent to

20W50.

Start-up Procedure

The following start-up procedure should

always be followed when starting a new

installation or when restarting an installation

in which the BDP has been removed from the

system.

 WARNING:

THE FOLLOWING PROCEDURE MAY

REQUIRE THE VEHICLE/MACHINE TO BE

DISABLED (WHEELS RAISED OFF THE

GROUND, WORK FUNCTION

DISCONNECTED, ETC.) WHILE

PERFORMING THE PROCEDURE IN

ORDER TO PREVENT INJURY TO THE

TECHNICIAN AND BYSTANDERS.

Prior to staring the BDP, make certain all

system components (reservoir, fittings, etc.)

are clean prior to filling with fluid.

Be certain to fill the BDP housing with

clean fluid prior to start-up. Fill the housing

by pouring filtered oil into the upper case

drain port, if possible.

Fill the reservoir with recommended fluid

which should be filtered prior to entering the

reservoir.

The inlet line and filter leading from the

reservoir to the charge pump must be filled

prior to start-up. Check inlet line for properly

tightened fittings and make sure it is free of

restrictions and air leaks.

Pressurizing the inlet 2-4 PSI will aid in start-

up. “Jog” or slowly rotate the engine with the

swashplate in its neutral (0 angle) position

until charge pressure starts to rise (charge

pressure is defined as low side loop

pressure).

 WARNING:

DO NOT START ENGINE UNLESS THE

PUMP IS IN THE NEUTRAL POSITION

(0 SWASHPLATE ANGLE) OR THE DRIVE

WHEELS ARE OFF THE GROUND.

Start the engine and run at the lowest

possible RPM.

With the bypass valve closed, slowly move

the displacement control in both the forward

and reverse directions. As air is purged from

the unit, the oil level in the reservoir will drop

and bubbles may appear in the fluid. Refill

the reservoir as necessary.

Place the displacement control in the neutral

position and open the bypass valve. Slowly

move the displacement control in both the

forward and reverse directions to purge the

air from the closed circuit.

Close the bypass valve and run the unit in

both directions for several minutes until any

remaining air is purged from the unit. Refill

the reservoir as necessary.

Shut down the engine, check for and correct

any fluid leaks, and check the reservoir level.

Add fluid if necessary. The transmission is

now ready for operation.

ENCORE

Maintenance

Check the reservoir daily for proper fluid

level, the presence of water (noted by a

cloudy to milky appearance, or free water in

bottom of reservoir), and rancid fluid odor

(indicating excessive heat).

The BDP-10L units normally do not require

regular fluid changes. The system filter

should be changed per the vehicle/machine

manufacturer’s recommendations. The fluid

and filter should be changed and the system

cleaned if the fluid becomes contaminated

with foreign matter (water, dirt, grease, etc.)

or if the fluid has been subjected to

temperature levels greater than the maximum

recommended.

Notes:

ENCORE WARRANTY

For Prowler and Z Series Mowers

(excluding the Z 34)

This warranty extends to the original retail purchaser only and commences on the date of

original retail purchase. Any part of the Encore commercial mower manufactured by

Encore Mfg. Co., Inc. and found in reasonable judgment of Encore Mfg. Co., Inc. to be

defective in material or workmanship will be repaired or replaced by an Authorized Encore

Dealer without charge for parts and labor. The Encore mower including any defective part

must be returned to an Authorized Encore Service Dealer within the warranty period. The

expense of delivering the mower to the dealer for warranty work and the expense of

returning it back to the owner after repair or replacement will be paid by the owner. This

warranty is limited to two year for frame, deck, hydrostatic drive system (excluding hoses),

gear-box and drive shaft. The warranty will be first year parts and labor, second year

parts only, from the date of purchase, against defects in workmanship and material (90

days for rental use) for any Encore Rider that is used for commercial or any other income

producing purpose. Cutter housings will carry a 2 year warranty parts and labor. Belts and

tires are warranted for 90 days against defects in materials and workmanship.

Cutter housings, electrical components, hydraulic components and electric-clutch must be

returned before warranty will be paid.

The engine is covered by its respective manufacturer please refer to the manufacture’s

warranty statement that is included in the literature packet. Engine warranties should be

referred to the nearest authorized service outlet of the engine manufacturer.

The responsibility of Encore Mfg. Co., Inc. in respect to claim is limited to making the

required repairs or replacements, and no claim of breach of warranty shall be cause for

cancellation or recession of the contract of sale of any Encore mower.

Proof of purchase is required by both Encore and the servicing Dealer, before any

warranty will be paid, and warranty work must be preformed by an Authorized Encore

service dealer.

This warranty does not cover any Encore mower that has been altered or modified so as

to adversely affect the intended use of the product, it operation, performance, or durability.

This warranty also does not cover any mower that has been subject to misuse, neglect,

negligence, accident or that has been operated in any way contrary to the operating

instructions as specified in the Operators Manual.

Encore Mfg. Co., Inc. reserves the right to change or improve the design of any mower

without assuming any obligation to modify any mower previously manufactured.

Encore Mfg. Co., Inc. obligation under warranty is strictly and excessively limited to repair

or replacement of defective parts. Encore Mfg. Co., Inc. does not assume or authorize

anyone to assume for them any other obligation.

ENCORE MFG. CO., INC. CANNOT BE RESPONSIBLE FOR THE WAY YOU OPERATE,

OR THE CONDITIONS IN WHICH YOU OPERATE THE MOWER. USE COMMON

SENSE AT ALL TIMES.

As of September 1, 2002 this warranty statement supersedes any warranty statement

published by ENCORE MANUFACTURING CO., INC.

,ENCORE MANUFACTURING CO., INC.

1102 A

Z SERIES

42K17Z - OPERATORS MANUAL

933077

Encore 42K17Z Z-Series Owner's manual

Brand: Encore

Model: 42K17Z Z-Series

Category: Tractor

Type: Owner's manual

Download PDF

report

Encore 42K17Z Z-Series Owner's manual

Encore 42K17Z Z-Series Owner's manual

Related papers

Other documents