Crosley CRT151HQW0 Owner's manual

CRT151HQW0
Crosley
Brand
Crosley
Model
CRT151HQW0
Category
Fridges
Type
Owner's manual
CROSLEY
TABLE OF
Wecome & Congratulabons ......................... 2
Important Safety Instructions ...................... 3
[nstallatuon ................................................ 5
Door Removal Instructions .......................... 7
Handle Installation ..................................... 9
Connecting Water Supply .......................... 11
www.fngJdaire.com USA 1-800-944--9044
CONTENTS
Ice Serwce ............................................... 13
Controls ................................................... 14
Normal Operating Sounds and Sughts......... 15
Care and Qeanmg .................................... 16
Before you Call ......................................... 18
Major Apphance Warranty ......................... 19
www.fngJdaJre.ca Canada 1-800-265-8352
£o
o
_J
o
Congratulations on your purchase of a new
refrigerator! We here at Crosley Corporation are
very proud of our product and we are completely
committed to providing you with the best service
possible. Your satisfaction is our #1 priority.
Please read this Use & Care Manual very
carefully. It contains valuable information on
how to properly maintain your new refrigerator.
We know you'll enjoy your new refrigerator
and Thank You for choosing our product. We
hope you consider us for future purchases.
Please Read and Save these
Instructions
This Use & Care Manual provides specific operating
instructions for your model. Use your refrigerator
only as instructed in this manual. These instructions
are not meant to cover every possible condition
and situation that may occur. Common sense
and cautionmust be practiced when installing,
operating and maintaining any appliance.
Please record your model and serial numbers
below for future reforenoe. This information
isfound on the serial plate located inside the
refrigerator compartment
Model Number:
Serial Number:
Purchase Date:
For product information contact:
336-761-1212
Crosley Corporation
111 Cloverleaf Dr.
Winston-Salem, NC 27103
www.crosley.com
Pleaseattach salesreceipt
herefor future reference.
Use only soap and water to clean serial plate.
Please complete and mail in the
Product Registration Card
included with your refrigerator,
Please read all instructions before using this
For your Safety
• DO NOT store or use gasoline, or other
flammable liquids in the vicinity of this or
any other appliance. Read product labels
for warnings regarding flammability and
other hazards.
• DO NOT operate the refrigerator in the
presence of explosive fumes.
• Avoid contact with any moving parts of
automatic ice maker.
• Remove all staples from the carton. Staples
can cause severe cuts, and also destroy
finishes Jfthey come in contact with other
appliances or furniture.
Definitions
_lbThis Jsthe safety alert symbol. It Jsused to
alert you to potential personal injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER indicates an imminently hazardous
situation which, Jf not avoided, will result in
dea!h or sed0us Jn!u_' ......................................................................................................
WARNING indicates a potentially hazardous
situation which, Jf not avoided, could result
in death or serious injury.
CAUTION indicates a potentially hazardous
situation which, Jf not avoided, may result in
minor or moderate injury.
IMPORTANT indicates installation, operation
or maintenance information which is
,mportaotbutoothazard-related.
Doors
[] Handles are secure and tight
[] Door seals completely to cabinet on all
sides
[] Freezer door is level across the top
Leveling
[] Refrigerator is level, side-to-side and
tilted 1/4"(6mm) front-to-back
[] Toe grille Jsproperly attached to
refrigerator
[] Cabinet is setting solid on all corners
Electrical Power
[] House power turned on
[] Refrigerator plugged in
Ice Haker
[] House water supply connected to
refrigerator
[] No water leaks present at all connections
- recheck Jn 24 hours
[] Ice maker Jsturned ON
[] Ice & water dispenser operates correctly
[] Front filter must be flush with filter
housing (select models)
Final Checks
[] Shipping material removed
[] Fresh food and freezer temperatures set
[] Crisper humidity controls set
[] Registration card sent in
Child Safety
Destroy or recycle the carton, plastic bags, and
any exterior wrapping material immediately
after the refrigerator Jsunpacked. Children
should never use these items to play. Cartons
covered with rugs, bedspreads, plastic sheets
or stretch wrap may become airtight chambers,
and can quickly cause suffocation.
Proper Disposal of your
Refrigerator or Freezer
Risk of child entrapment
Child entrapment and suffocation are not
problems of the past. 3unked or abandoned
refrigerators or freezers are still dangerous-
even if they will sit for"just a few days" If you
are getting rid of your old refrigerator or freezer,
please follow the instructions below to help
prevent accidents.
Proper Disposal of Refrigerators/Freezers
We strongly encourage responsible appliance
recycling/disposal methods. Check with your utility
company or visit www.energystar.gov/recyde for
more information on recycling your old refrigerator.
Before you throw
away your old
refrigerator/
freezer:
Remove doors.
Leave shelves in
place so children
may. Rot easily
CllmO inslae.
Have refrigerant
removed 5y a
qualifiea service
tecnnician.
These guidelines must be followed to ensure
that safety mechanisms in this refrigerator
willoperateproperly............
Electrical information
• The refrigerator must be plugged into its own
dedicated 115 Volt, 60 Hz., 15 Amp, AC only
electrical outlet. The power cord of me appliance
is equipped with a three-prong grounding
plug for your protection against electrical
shock hazards. It must be plugged directly into
a properly grounded three prong receptade. The
receptacle must be installed in accordance with
local codes and ordinances. Consult a qualified
electrician. Avoid connecting refrigerator to a
Ground Fault Interrupter (GFI) circuit. Do not
use an extension cord or adapter plug.
• If the power cord is damaged, it should
be replaced by an authorized service
technician to prevent any risk.
• Never unplug the refrigerator by pulling on
the power cord. Always grip the plug firmly,
and pull straight out from the receptacle to
prevent damaging the power cord.
Unplug the refrigerator before cleaning
and before replacing a light bulb to avoid
electrical shock.
Performance may be affected if the voltage
varies by 10% or more. Operating the
refrigerator with insufficient power can
damage the compressor. Such damage is
not covered under your warranty.
Turning the Freezer and Fresh Food
controls to "0" (Mechanical controls) or
"OFF" (Electronic controls) will disable your
refrigerator's cooling system, but does not
disconnect the power to the light bulb and
other electrical components. To turn off
power to your refrigerator you must unplug
the power cord from the electrical outlet.
Grounding type wall receptacle
Power cord with
To avoid personal injury or property
damage, handle tempered glass shelves
carefully. Shelves may break suddenly if
nicked, scratched, or exposed to sudden
temperature change.
CFC/HCFC Disposal
Your old refrigerator may have
a cooling system that used CFCs
or HCFCs (chlorofluorocarbons or
hydrochlorofluorocarbons). CFCs and
HCFCs are believed to harm stratospheric
ozone if released to the atmosphere. Other
refrigerants may also cause harm to the
environment if released to the atmosphere.
If you are throwing away your old
refrigerator, make sure the refrigerant is
removed for proper disposal by a qualified
technician. If you intentionally release
refrigerant, you may be subject to fines
and imprisonment under provisions of
environmental legislation.
Do not plug the unit into an electrical outlet
controlled by a wall switch or pull cord to
prevent the refrigerator from being turned
off accidentally.
ThisUse&CareGuideprovidesgeneral
operatinginstructionsforyourmodel.Usethe
refrigeratoronlyasinstructedinthisUse&
e
Care Guide. Before starting the refrigerator,
follow these important first steps.
Location
• Choose a place that is near a grounded
electrical outlet. Do Not use an extension
cord or an adapter plug.
• If possible, place the refrigerator out of
direct sunlight and away from the range,
dishwasher or other heat sources.
• The refrigerator must be installed on a floor
that is level and strong enough to support
a fully loaded refrigerator.
• Consider water supply availability for
models equipped with an automatic ice
maker. If you do not hook up water to
the refrigerator, remember to turn the ice
maker off.
e
To
1.
The cabinet should be level at the front
and rear.
The sides should tilt 1/4-inch (6 mm) from
front-to-back (to ensure that doors close
and seal properly).
Doors should align with each other and be
level.
install the toe grille:
Attach toe grille support bracket to cabinet
using 3 bolts supplied.
Do Not install the refrigerator where the
temperature will drop below 55°F (13°C) or
rise above 110°F (43°C). The compressor
will not be able to maintain proper
temperatures inside the refrigerator.
Do Not block the toe grille on the lower front
of your refrigerator. Sufficient air circulation
is essential for the proper operation of your
refrigerator.
Installation
Installation clearances
• Allow the following clearances for ease
of installation, proper air circulation, and
plumbing and electrical connections:
Sides & Top 3/8inch
Back 1 inch
2,
If your refrigerator is placed with the door
hinge side against a wall, you may have to
allow additional space so the door can be
Guidelines for final positioning of your
refrigerator:
• All four corners of the cabinet must rest
firmly on the floor.
3.
Install left toe grille cover onto slot on
left side of toe grille.
"-.. ÷J
%,
Attach toe grille to cabinet.
or
some models
To level the cabinet using the front
rollers:
1
2
Remove the toe grille.
Use a flat-blade screwdriver or % inch
socket wrench to raise or lower the front
rollers (Figure 2).
Raise
F-
t
\!
Figure 2
or
Use adjustable wrench to adjust leveling
screws. Lower the leveling screws on each
side clockwise until they contact the floor
(Figure 3).
Raise the front of the refrigerator enough so
the doors close freely when opened halfway.
The refrigerator should slope 1/4inch to
1/2inch from front-to-back. Then level the
refrigerator from side-to-side.
4 Some models are equipped with an anti-
tip bracket (Figure 4). Lower it clockwise
until it contacts the floor.
Figure 4 (some models)
A The antFtip device must be
Jj,_, installed according to the
J/%_ instructions in your Use &
Z_ Care Manual. Failure to do
SOw! resut !n!njury.
When reversing the door swing:
You MUST move the anti-tip bracket to align
with the hinges of the door. Failure to do so
will result in injury.
Raise
Figure 3
Tools Necessary:
....__sT MHead
Top Hinge _ d_,Top Hinge
Cover Front %_._ "_-_Cover Rear
S.... H _4I s....
_Top Bottom _
Socket
Wrench Set
or or
The direction in which your refrigerator doors open (door swing) can be reversed, from left
to right or right to left, by moving the door hinges from one side to the other. Reversing the
doo r swing sheu!d be Performe d by qua!!fie d person: ........................................................................................................................................................
Before you begin, turn the refrigerator temperature control to "0" (Mechanical controls) or
"OFF" (Electronic controls) and remove the electrical power cord from the wall outlet. Remove
any food from door shelves. ...........
Door removal and reversal
instructions:
1. Remove toe grille.
2.
Remove top hinge cover. Trace around the
hinge with a soft lead pencil. This makes
reinstallation easier. Remove top hinge
and lift door off center hinge pin. Set door
aside.
Top
Hinge
Cover
3.
Un crow on or ,n0o0,nu ,n0o0 o o0,o
wrench and save for reassembly. Ensure
plastic washer stays on hinge pin.
4.
5.
6.
Lift refrigerator door off of bottom hinge
and set aside.
Remove center hinge and shim by
removing inside screw and loosening two
outside screws enough to allow hinge and
shim to slide out. Tighten screws.
Loosen two outside screws on opposite
side of refrigerator, remove inside screw
and install center hinge.
I Door
her
_ge
.Center
'Screws
Handle
Hole
plug
7.Removethreescrewsonbottomhinge
andantFtipbracket(ifequipped)with3/8"
socketwrench.
8. Installbottomhingeandanti-tipbracket
(ifequipped)onoppositesidewiththe
threescrewsremovedfromstep7.
9.
10.
11.
12.
Unscrew bottom hinge pin using
adjustable wrench. Hove hinge pin to
other hole in hinge and tighten with
adjustable wrench.
Reverse door handles (see Handle
Installation section).
Move freezer and refrigerator door stops
to opposite side. Before starting screws,
use an awl to puncture the foam.
Position refrigerator door onto bottom
hinge pin and screw center hinge pin
through center hinge into top of door. Close
refrigerator door to help align hinge hole.
13. Tighten center hinge pin with adjustable
wrench.
14. Remove cabinet and hinge hole plugs and
move to opposite side.
15. Lower freezer door onto center hinge pin.
16. Close freezer door. Have an assistant
lift up on opposite side of door while
tightening screws to install top hinge.
17. There are two toe grille covers provided
in your literature packet; one for the right
side and one for the left side. Install the
appropriate cover over the opening on the
side opposite the anti-tip bracket, (see
Figures A & B).
In case of future door reversals, save the
toe grille cover not being used.
3
18.
19.
Flip toe grille and reinstall (some models).
Plug in electrical power cord and turn
refrigerator temperature control to center
position. Adjust setting as necessary.
When reversing the door swing:
You MUST move the anti-tip bracket to align
with the hinges of the door and install the
toe grille support for proper blance. Failure
to do so will result in injury.
Grille
Support
Toe Grille Cover A
Toe Grille
Anti.tip
Bracket B
WearglovesanduseextremeCAUTION
wheninstallingthesehandles.Therounded
3.Tightenthesetscrewontheroundedpart
ofthehandleuntilthehandleisflushwith
thedoor,thentightenanother1/2turn.
Toensureproperinstallationofhandles,
pleasereviewtheseinstructionsand
illustrationsthoroughlypriortoinstallingthe
handles.
Additionally,beforeinstallingthedoor
handles,makesurethedoorswingis
correct.Yourmodelwillhaveeithera
righthandorlefthanddoorswing.Follow
instructionsintheUse&CareGuideto
To attach metal refrigerator handle:
1.
Place rounded part of handle onto
shoulder screw on face of door and align
the two holes in top of handle with the
two holes in top of door. Do not tighten
the set screw yet.
2. Install the two screws into the top of the
handle.
3.
Tighten the set screw on the rounded part
of the handle until the handle is flush with
the door, then tighten another 1/2turn.
j-
Nameplate
Screw
Stainless Steel Hodels
= Screw
_- Handle
Shoulder
' Set
Screw
Shoulder
To attach metal freezer handle:
1. Place rounded part of handle onto
shoulder screw on face of door and align
the two holes in bottom of handle with
the two holes in bottom of door. Do not
tighten the set screw yet. "_
2. Install the two screws into the bottom of
the handle,
To attach plastic refrigerator handle:
1. Place top of handle over dovetail screw,
pull handle straight down until handle is
aligned with screw holes on top of door.
2. Secure top of handle with two screws.
To reverse refrigeratorlfreezer handles=
Handles may be easier to reverse while doors
are off. Reverse freezer and refrigerator
handles as shown.
To attach plastic freezer handle:
1,
Place top of handle over dovetail screw,
pull handle straight up until handle is
aligned with screw holes on bottom of
door.
2. Secure bottom of handle with two screws.
Be sure doors are set aside in a secure
position where they cannot fall and cause
personal injury,
Lock Handle
over
Screw ----_A Dovetail Screw
Toavoidelectricshock,whichcancause
deathorseverepersonalinjury,disconnect
therefrigeratorfromelectricalpowerbefore
connectingawatersupplylinetothe
refrige at°r-....................................................................................................................................
To Avoid Property Damage:
* Copper or Stainless Steel braided tubing
is recommended for the water supply
line. Water supply tubing made of 1/4
inch plastic is not recommended to be
used. Plastic tubing greatly increases
the potential for water leaks, and the
manufacturer will not be responsible for
any damage if plastic tubing is used for
the supply line.
* DO NOT install water supply tubing in
areas where temperatures fall below
freezing.
* Chemicals from a malfunctioning softener
can damage the ice maker. If the ice
maker is connected to soft water, ensure
that the softener is maintained and
working properly.
• A compression nut and ferrule (sleeve) for
connecting a copper water supply line to
the ice maker inlet valve.
Check with your local building authority
for recommendations on water lines and
associated materials prior to installing your
new refrigerator, Depending on your local/
state building codes, Frigidaire recommends
for homes with existing valves its Smart
Choice ® water line kit 5305513409 (with
a 6 ft. Stainless Steel Water Line) and for
homes without an existing valve, Frigidaire
recommends its Smart Choice ® water line
kit 5305510264 (with a 20 ft. Copper Water
Line with self-tapping saddle valve). Please
refer to www.frigidaire.com/store for more
information.
To Conne_ Water Supply Line To Ice
Maker Inlet Valve
1. Disconnect refrigerator from electric power
source.
2.
Place end of water supply line into sink or
bucket. Turn ON water supply and flush
supply line until water is clear. Turn OFF
water supply at shutoff valve.
Ensure that your water supply line
connections comply with all local plumbing
codes
Before Ins_lling The Water Supply Line,
You Will Need:
* Basic Tools: adjustable wrench, fiat-blade
screwdriver, and PhillipsTM screwdriver
* Access to a household cold water line with
water pressure between 30 and 100 psi.
* A water supply line made of 1/4inch (6.4
mm) OD, copper or stainless steel tubing.
To determine the length of tubing needed,
measure the distance from the ice maker
inlet valve at the back of the refrigerator
to your cold water pipe. Then add
approximately 7 feet (2.1 meters), so the
refrigerator can be moved out for cleaning
(as shown).
* A shutoff valve to connect the water supply
line to your household water system. DO
NOT use a self-piercing type shutoff valve.
* Do not re-use compression fitting or use
thread seal tape.
3.
4.
5.
6.
Remove plastic cap from water valve inlet
and discard cap.
If you use copper tubing - Slide brass
compression nut, then ferrule (sleeve)
onto water supply line. Push water supply
line into water valve inlet as far as it
will go (1/4inch / 6A mm). Slide ferrule
(sleeve) into valve inlet and finger tighten
compression nut onto valve. Tighten
another half turn with a wrench; DO NOT
over tighten. See Figure 1.
If you use stainless steel tubing - The
nut and ferrule are already assembled on
the tubing. Slide compression nut onto
valve inlet and finger tighten compression
nut onto valve. Tighten another half turn
with a wrench; DO NOT over tighten. See
Figure 2.
With steel clamp and screw, secure water
supply line (copper tubing only) to rear
panel of refrigerator as shown.
Coil excess water supply line (copper
tubing only), about 21/2turns, behind
refrigerator as shown and arrange coils so
they do not vibrate or wear against any
other surface.
7.TurnONwatersupplyatshutoffvalveand
tightenanyconnectionsthatleak.
8. Reconnectrefrigeratortoelectricalpower
source.
9. Toturnicemakeron,lowerwiresignal
arm(sidemounted)orsettheicemaker's
On/Offpowerswitchtothe"["position
(rearmounted).
PlasticWater
Compression
Nut
:Ferrule
leeve)
)er
line
Bracket
Valve Inlet
water supply
Include enough tubing inloop
3 allow moving refrigerator out
for cleaning:)
Figure 1
Plastic
Steel
water Line
Bracket
; Inlet
Water Valve
6 ft. Stainless Steel water line
ipply
Figure 2
If your refrigerator has an automatic ice maker,
minimal ice will be produced during the first 24
hours of operation. Air in new plumbing lines
may cause the ice maker to cycle two or three
times before making a full tray of ice. With no
usage, it will take approximately one to two
days to fill the ice container.
New plumbing connections may cause the first
production of ice cubes to be discolored or
have an odd flavor. Discard ice made during
the first 24 hours.
Automatic ice makers are also optional
accessories that may be installed in most
models at any time. Call your local dealer for
information.
Turning your Ice Maker On
After the plumbing connections have been
completed, the water supply valve must be
opened. Place the ice container under the
ice maker, pushing it as far back as possible.
Lower the wire signal arm to its "down" or ON
position.
Turning your Ice Maker Off
To stop the ice maker, lift the wire signal
arm until it clicks and locks in the "up" or
OFF position. The ice maker also turns off
automatically when the ice container is full.
ON
Your ice maker is shipped from the factory
with the wire signal arm in the ON position.
To ensure proper function for your ice maker,
hook up water supply immediately or turn ice
maker OFF by lifting the wire signal arm until
it clicks and locks in the UP position. If the
ice maker is on and the water supply is not
connected, the water valve will make a loud
chattering noise.
ICE PRODUCTION: WHAT
TO EXPECT
The ice maker will produce 2.5 to 3 pounds
of ice every 24 hours depending on usage
conditions. Ice is produced at a rate of 8 cubes
every 80 to 160 minutes.
Do Not place the ice container in your
Cool Down Period
To ensure safe food storage, allow the
refrigerator to operate with the doors closed
for at least 8 hours before loading it with food.
Refrigerator & Freezer Controls
(some models)
Cool Down Period
To ensure safe food storage, allow the
refrigerator to operate with the doors closed
for at least 8 hours before loading it with food.
Refrigerator & Freezer Controls
(some models)
When first turning refrigerator on, adjust
the refrigerator control to Normal. This isthe
recommended initial setting. After 24 hours,
If your unit is in a garage or area where the
temperature is below 55°, adjust the freezer
control to the coldest setting.
Allow 24 hrs for adjustments
Norma_.,",_
__,l_-_ ilo._o_de
i
temperature
garage, t__ offC°ldC°ldest*
Refrigerator/Freezer Control
Temperature Adjustment
* Adjust temperature gradually: adjust the
knob in small increments, allowing the
temperature to stabilize.
* For colder temperatures, adjust the knob
towards Colder.
* For warmer temperatures, adjust the knob
towards Cold.
Adjusting the refrigerator/freezer control will
change temperatures in both compartments.
The auxiliary freezer control can be left at
the factory pre-set (Normal) or adjusted as
desired; it has no effect on electrical power to
the refrigerator.
To maintain temperatures, a fan circulates air in
the refrigerator and freezer compartments. For
good circulation, do not block cold air vents with
food items.
Adjusting the refrigerator/freezer temperature
control to "0" turns off the compressor and
prevents the refrigerator from cooling, but
does not disconnect the power to the light
* recommended bulb and other electrical components. To turn
off power to your refrigerator, you must unplug
the power cord from the wall outlet.
E J
Auxiliary Freezer Control
1
Understanding the sounds you
may hear
Your new, high-effidency refrigerator may
introduce unfamiliar sounds. These sounds
normally indicate your refrigerator is operating
correctly. Some surfaces on floors, walls, and
kitchen cabinets may make these sounds more
noticeable.
Rigid foam insulation is very energy efficient,
but is not a sound insulator.
Following is a list of major components in your
refrigerator and the sounds they can cause:
A Evaporator Refrigerant through the
evaporator may create a boiling or
gurgling sound.
B Evaporator fan You may hear air being
forced through the refrigerator by the
evaporator fan.
Defrost heater During defrost cycles,
water dripping onto the defrost heater
may cause a hissing or sizzling sound.
After defrosting, a popping sound may
Occur.
wall of your freezer compartment. This is
normal during the defrost cycle.
D Automatic ice maker When ice has
been produced, you will hear ice cubes
falling into the ice bin.
During the automatic defrost cycle, you may
notice a red glow in the vents on the back
Electronic defrost control These parts
can produce a snapping or clicking sound
when turning the cooling system on and
off.
F Condenser fan You may hear air being
forced through the condenser.
G
Compressor Modern, high-efficiency
compressors run much faster than in the
past. The compressor may have a high-
pitched hum or pulsating sound.
Water valve If your refrigerator is
equipped with an automatic ice maker,
you will hear a buzzing sound as the water
valve opens to fill the ice maker during
each cycle.
I Drain pan (not removable) You may hear
water dripping into the drain pan during
the defrost cycle.
J Condenser May create minimal sounds
from forced air.
If the Fresh Food door is left open form more than 5 minutes, an alarm will sound. The alarm
will sound for 2 minutes and then stop. If the "Door Ajar" condition remains, the alarm will
repeat every 30 minutes for two intervals.
After 15 minutes of a "Door Ajar" Condition, the unit will turn the Fresh Food light off until the
door is closed. The door switch in the Fresh Food can be pressed and released to reset the
alarm and light.
Protecting your investment
Keeping your refrigerator clean maintains
appearance and prevents odor build-up. Wipe
up any spills immediately and clean the freezer
and fresh food compartments at least twice
a year. When cleaning, take the following
precautions:
• Never use CHLORIDE or cleaners with
bleach to clean stainless steel.
• Do not wash any removable parts in a
dishwasher.
• Always unplug the electrical power cord
from the wall outlet before cleaning.
• Remove adhesive labels by hand. Do not
use razor blades or other sharp instruments
which can scratch the appliance surface.
• Do not remove the serial plate.
Do not use abrasive cleaners such as
window sprays, scouring cleansers, brushes,
flammable fluids, cleaning waxes, concentrated
detergents, bleaches or cleansers containing
petroleum products on plastic parts, interior
doors, gaskets or cabinet liners. Do not use
paper towels, metallic scouring pads, or other
abrasive cleaning materials or strong alkaline
solutions.
If you store or move your refrigerator in
freezing temperatures, be sure to completely
drain the water supply system. Failure to
do so could result in water leaks when the
refrigerator is put back into service. Contact
a service representative to perform this
operation.
If you set your temperature controls to
turn off cooling, power to lights and other
electrical components will continue until you
Pull the refrigerator straight out to move
it. Shifting it from side to side may
damage flooring. Be careful not to move
the refrigerator beyond the plumbing
connections.
;= Damp objects stick to cold metal surfaces.
Do not touch refrigerated surfaces with wet
Or damp hands.
Care 8=Cleaning Tips
Part. What To Use I Tips and PrecautionS
Interior & • Soap and water Use 2 tablespoons of baking soda in 1 quart of warm
Door Liners • Baking soda and water. Be sure to wring excess water out of sponge
water or cloth before cleaning around controls, light bulb
or any electrical part.
Door ® Soap and water wipe gaSkets With a clean soft €!0thl
Gaskets •
Drawers & + Soap and water Use a soft cloth to clean drawer runners and tracks.
Bins
Glass ',soap and Water Allow glass to warm to room temperatuie before
immersing in warm water.
+ Mild liquid sprays i
Toe Grille + Soap and water Vacuum dust from front of toe grille. Remove
+ Mild liquid sprays toe grille (see Installation Instructions). Vacuum
backside, wipe with sudsy cloth or sponge. Rinse
+ Vacuum attachment and dry.
Exterior & + Soap and water Do not use commercial household cleaners
Handles * Non Abrasive Glass containing ammonia, bleach or alcohol to clean
' cleaner handles. Use a soft cloth to clean smooth handles.
- DO NOT use a dry cloth to clean smooth doors.
Exterior & + Soap and water Never use CHLORIDE or cleaners with bleach to
Handles + Stainless Steel clean stainless steel.
(Stainless Cleaners Clean stainless steel front and handles with non-
Steel abrasive soapy water and a dishcloth. Rinse with
Models clean water and a soft cloth. Use a non-abrasive
Only) stainless steel cleaner. These cleaners can be
purchased at most home improvement or major
department stores. Always follow manufacturer's
instructions. Do not use household cleaners
containing ammonia or bleach.
NOTE: Always clean, wipe and dry with the grain
to prevent scratching. Wash the rest of the cabinet
with warm water and mild liquid detergent. Rinse
well, and wipe dry with a clean soft cloth.
Replacing I Unplug reffigerai0r CAUTION: wear gloVes When rep!acing light buibs to
Light Bu DS i + wear gloves avOidbulbgetting cut, Use same wattage when replacing
+ Plug in the
+ refrigerator
...._iiiiii
_!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!_ii
l-800-944-9044 (United States) 1
1-800-265-8352 (Canada)
Visit our web site at
www.frigidaire.com.
Common Occurrences Before Calling for Service' review this !ist: It may save You
time and expense. This list includes common occurrences
that are not the result of defective workmanship or
materials in this appliance.
Refrigerator does not run. * Ensure plug is tightly pushed into electrical outlet.
• Check/replace fuse with a 15 amp time-delay fuse. Reset
circuit breaker.
• The refrigerator/freezer control is turned to"0"
(Mechanical controls) or "OFF" (Electronic controls).
• Refrigerator may be in defrost cycle. Wait 20 minutes
and check again.
Freezer temperature is colder" _ Set aUXiliaWfreezer contrOl tO a Warmer setting until
than preferred. Refrigerator freezer temperature is satisfactory, Allow 24 hours for the
temperature is satisfactory, temperature to stabilize.
Refrigerator temperature is too * Set refrigerator/freezer control to a warmer setting. Allow
cold. Freezer temperature is 24 hours for temperature to stabilize. Then check freezer
satisfactory, temperatures and adjust as needed.
set auXiliary freezer control to a €oider setting
than preferred. Refrigerator
temperature is satisfactory.
Refrigerator temperature is
warmer than preferred. Freezer
temperature is satisfactory.
Refrigerator is noisy or vibrates.
freezer temperature is satisfactory, Allow 24 hours for the
temperature to stabilize.
Set refrigerator/freezer control to a colder setting.
Allow 24 hours for temperature to stabilize. Then check
refrigerator temperatures and adjust as needed.
The cabinet is not level:
- See Normal Operating Sounds and Sights section.
Odors in refrigerator. * Interior needs to be cleaned.
Foods that produce odors should be covered or wrapped.
cabinet light n0tw0rkingl I _ Replace light bUibl
Ensureplug is t!ghtly pushed into electrical outleL
, Light switch may be Stuck. Push in light switch, located
- on the refrigerator control box, to release.
Automatic ice maker not • Ensure the wire signal arm is not in UP position.
working (some models) • Ice maker should produce 2.5 to 3 pounds of ice in a 24
hour period.
• Water supply is turned off.
• Water pressure is too low.
• The freezer is not cold enough.
Refrigerator makes beeping _ Close door.
I
sound. ,, Press light switch.
18
Hajor Appliance Warranty Information
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Crosley will pay all costs for repairing or replacing any parts of this appliance that prove to
be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
*In addition to warranty shown above, ask your dealer about Crosley Extended Limited Warranty that
comes to you at no extra charge for the 2nd through lOth years.
Exclusions This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased "as-is" are not covered by this warranty.
S. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc.,which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or
knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Crosley parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASEDON IMPLIED WARRANTIES, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED TO ONE YEAR
OR THE SHORTEST PERIOD ALLOWED BY LAW,BUT NOT LESS THAN ONE YEAR. CROSLEY SHALL NOT BE
LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCHAS PROPERTY DAMAGE AND INCIDENTAL
EXPENSESRESULTING FROM ANY BREACHOF THIS WRIII-EN LIMITED WARRANTY OR ANY IMPLIED
WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE
LIMITATIONS OR EXCLUSIONS MAY NOT APPLYTO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATETO STATE.
If You Need
Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Crosley at the addresses or phone
numbers below.
This warranty only applies inthe USA and Canada. Your appliance is warranted by Crosley Corporation. Crosley authorizes no
person to change or add to any obligations under this warranty. Obligations for service and parts under this warranty must be
performed by Crosley or an authorized service company. Product features or specifications as described or illustrated are subject
to change without notice.
FOR WARRANTY iNFORMATiON CONTACT: FOR PRODUCT INFORMATION CONTACT:
USA 800-944-9044
Canada 800-265-8352
336-761-1212
Crosley Corporation
111 Cloverleaf Dr.
Suite 200
Winston-Salem, NC 27103
v,_ww c[osle>/:co_n
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19

Crosley CRT151HQW0 Owner's manual

CRT151HQW0
Crosley
Brand
Crosley
Model
CRT151HQW0
Category
Fridges
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents