Munters ZEW Profi Inlet Owner's manual

Brand: Munters

Model: ZEW Profi Inlet

Type: Owner's manual

1© Munters Corporation, April 2019

QM1116r1

Instruction Manual

Insulated Sidewall Inlet

Models: RV-ZEWP2900-AO • RV-ZEWP2900-AC

Munters

Insulated

Sidewall Inlet

RV-ZEWP2900-AO

RV-ZEWP2900-AC

QM1116r1

Insulated Sidewall Inlet

Instructions for Use and Maintenance

Thank You:

Thank you for purchasing a Munters Insulated Sidewall Inlet. Munters equipment is designed to be the highest

performing, highest quality equipment you can buy. With the proper installation and maintenance it will provide

many years of service.

Please Note:

To achieve maximum performance and insure long life from your Munters product it is essential that it be installed

and maintained properly. Please read all instructions carefully before beginning installation.

Warranty:

For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the

Munters Corporation office at 1-800-227-2376 or by e-mail at [email protected].

Conditions and Limitations:

• Products and Systems involved in a warranty claim under the “Warranty Claims and Return Policy” shall have

been properly installed, maintained and operated under competent supervision, according to the instructions

provided by Munters Corporation.

• Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper installation

or maintenance shall not be considered a defect under the Warranty

3© Munters Corporation, April 2019

QM1116r1

Index

Chapters Page

1. Unpacking the Equipment 4

1.1 Parts List 4

1.2 Inlet Dimensions 4

2. Installation Instructions 5

3. Cabling 12

QM1116r1

1.1 Parts List

Unpacking the Equipment

Before beginning installation, check the overall condition of the equipment. Remove packing materials, and examine all

components for signs of shipping damage. Any shipping damage is the customer's responsibility and should be reported

immediately to your freight carrier.

1.2 Inlet Dimensions

Each Sidewall Inlet includes:

1 - Inlet Frame with Bird Screen

2 - Inlet Side Panels

1 - Inlet Door

2 - Inlet Door Bracket

1 - Inlet Directional Flap

1 - Hardware Package

[A]

[B]

[C]

[D]

[E]

[F]

[G]

Wall Opening

⁄8" [505mm] H. x 29

⁄8" [746mm] W.

Hardware Package

ID Qty. Description

[A] 2 5.3 x 15mm Washer

[B] 3 8.4 x 17mm Washer

[C] 12 M5 x 25mm Pan Head Screw

[D] 2 M6 x 30mm Bolt

[E] 2 M5 x 50mm Raised Head Screw

[F] 3 M5 x 80mm Countersink Screw

[G] 2 115mm Tension Spring

[H] 2 Directional Flap Adjustment Bushing

32” [813mm]

⁄8” [574.5mm]

⁄4”

[108]

⁄8” 18” [457mm]

⁄4”

[108]

[H]

5© Munters Corporation, April 2019

QM1116r1

Installation Instructions

⁄

” [746mm] W.

10" - 12" Min.

⁄8” [505mm] H.

Framing

Frame Construction

Figure 1A

Post Construction

Figure 1B

Step 1

Construct a framed opening to correct size according to Wall Opening listed in chart on previous page. A

minimum of 10” - 12” from ceiling to the top inside of the stud.

See Figure 1A and 1B.

⁄

” [746mm] W.

⁄

”

[505mm]

QM1116r1

Pan Head Screw [C]

Alignment Notch

Inlet Frame

Alignment Notch

Step 2

Find the Inlet Frame and secure (2) Side Panels to it using (8) Pan Head Screws [C]. Make sure Side Panels

are aligned and fully seated to Inlet Frame before securing. See Figure 2.

Installation InstructionsChapter 2

Step 3

Slide Inlet Door into Inlet between Side Panels with the wider portion of the door towards the bottom of Inlet.

Then slide the Pin of the Door Bracket through Side Panel and into Inlet Door. Repeat for other side.

See Figure 3.

Figure 3

Figure 2

Side Panel

Inlet Door

Side Panel

Inlet Frame with

Side Panels

Door Bracket with Pin

7© Munters Corporation, April 2019

QM1116r1

Installation InstructionsChapter 2

Step 5

Slide Directional Flap into Inlet between Side Panels and fasten in place using (2) M6 Bolts [D].

See Figures 5.

Inlet

Figure 5

Step 4

Make sure Door Bracket is aligned with the edge of inlet and secure in place using (2) Pan Head Screws [C].

Repeat for other side. Make sure door opens and closes freely. See Figures 4.

Pan Head Screw [C]

Door Bracket with Pin

Directional Flap

M6 Bolt [D]

Figure 4

QM1116r1

Installation InstructionsChapter 2

Step 6

Insert Directional Flap Bushing [H] into slot in Side Panel. Insert

Raised Head Screw [E] through 15mm Washer

[A] and Directional Flap Bushing [H] into hole in Directional Flap and tighten to a snug fit. DO NOT over

tighten, Directional Flap should be able to adjust to each notch in Bushing. See Figures 6.

15mm Washer [A]

Figure 6

Hole in Directional Flap

Directional Flap Bushing

Slot in Side Panel

Raised Head

Screw [E]

9© Munters Corporation, April 2019

QM1116r1

Installation InstructionsChapter 2

Step 7

For the AO (Auto Open) Inlet, thread the large Blue Nut onto Lift Arm and press Lift Arm onto Spacer Block. Attach

Lift Arm with Spacer Block to Door using (3) Countersink Screw [F] and 17mm Washer [B]. See Figures 7A. For

the AC (Auto Close) Inlet, attach Lift Arm to Door using (3) Countersink Screw [F] and 17mm Washer [B].

See Figures 7B.

Door

Lift Arm

Countersink [F] and

15mm Washer [B]

Door

Spacer Block

Large Blue Nut

Lift Arm

Countersink [F] and

15mm Washer [B]

AO (Auto Open) Inlet

Figure 7A

AC (Auto Close) Inlet

Figure 7B

QM1116r1

Installation InstructionsChapter 2

Step 8

For the AO (Auto Open) Inlet, attach (2) Tension Spring [G] from the brackets on the door to the brackets in the

inlet frame. See Figures 8A. For the AC (Auto Close) Inlet, attach (2) Tension Spring [G] from bracket on center

support to bracket on inside of door. See Figures 8B.

AO (Auto Open) Inlet

Figure 8A

AC (Auto Close) Inlet

Figure 8B

Tension Spring [G]

Bracket in Inlet Frame

Bracket on Door

Tension Spring [G]

Bracket on Center Support

11© Munters Corporation, April 2019

QM1116r1

Installation InstructionsChapter 2

Step 9

Apply a bead of caulk to face of framing, then slide inlet into framing. See Figures 9.

Figure 10

Step 10

Secure inlet in framing using (6) 2” Pole Barn Screws (not provided). Be sure not to overtighten screws and

damage inlet. See Figures 10.

Figure 9

Inlet

Framing

2” Pole Barn Screw (not provided)

QM1116r1

Figure 11B

AC1039 Cable Clamps. Thread cable

through loop at end of spring and

fasten with (2) cable clamps.

AC1264 Single Pulley Bracket.

Recess pulley into ceiling in order

to keep cable in line with rod.

Building Wall

Ceiling

AC1195 Baﬄ e return spring

Fasten spring into stud with lag

screw or bolt and nut.

Truss

AC1013 or

AC1044 Cable

SPRING TENSION:

with baﬄ e fully closed and cable pulled tight,

stretch spring 12" - 14" and fasten.

Step 11

Attach pulleys in line with screw hooks at each endwall. See Figure 11A and 11B.

Figure 11A

AC1264 Single Pulley

Bracket. Provide adequate

support.

Ceiling

Building Wall

WINCH/ ACTUATOR END

SPRING END

Cabling

QM1116r1

CablingChapter 3

Step 12

For the AO (Auto Open) Inlet, install the Wall Guide Bracket 7⁷⁄₈” [200mm] above the top of the inlet using

(3) 2” Pole Barn Screws (not provided). See Figures 12A. For the AC (Auto Close) Inlet install the Wall Guide

Bracket 4” [100mm] below the bottom of the inlet using (3) 2” Pole Barn Screws (not provided).

See Figures 12B.

Wall Guide Bracket

2” Pole Barn Screw (not provided)

7⁷⁄₈”

[200mm]

AO (Auto Open) Inlet

Figure 12A

AC (Auto Close) Inlet

Figure 12B

Wall Guide Bracket

2” Pole Barn Screw (not provided)

4” [100mm]

QM1116r1

CablingChapter 3

Step 13A

For the AO (Auto Open) Inlet, run Main Rod or Cable in outer groove of Wall Guide. Additional support

for Main Rod or Cable may be required. Attach Lift Line to Main Rod/Cable 14” back from Wall Guide

toward Actuator using cable clamp. Run lift line through the hole in the end of the Wall Guide and down

through the hole in the Lift Arm and secure by tightening the large Blue Nut on end of Lift Arm.

See Figure 13A.

Lift Line

Cable Clamp

Large Blue Nut on

end of Lift Arm

Wall Guide

Main Rod or Cable

To Actuator or Winch

AO (Auto Open) Inlet

Figure 13A

QM1116r1

CablingChapter 3

Step 13B

For the AC (Auto Close) Inlet, run Main Rod or Cable in outer groove of Wall Guide. Additional support

for Main Rod or Cable may be required. Hang supplied Swivel Pulley in outer hole in Lift Arm. Attach

Lift Line to Main Rod/Cable 14” back from Wall Guide toward Actuator using cable clamp. Run lift line

through the hole in the end of the Wall Guide and up over Swivel Pulley and back down through hole in

Wall Guide closest to wall and secure with Azuma Bolt and Nut or similar (not provided). See Figure 13B.

AC (Auto Close) Inlet

Figure 13B

Lift Line

Cable Clamp

Outer Hole in

Wall Guide

Outer Groove in Wall Guide

Main Rod or Cable

To Actuator or Winch

Lift Arm

Swivel Pulley

QM1116r1

CablingChapter 3

Step 14

With the winch at its fully closed position, go back, check and readjust each baffle door tightly to

inlet frame. Use winch or actuator to open and close inlets a few times to make sure inlet moves

smoothly and each door remains even over the total length of house. See Figure 14.

Figure 14

To Weights or

Return Spring

QM1116r1

This page left blank intentionally

QM1116r1

Munters Europe AB, Isafjordsgatan 1, P.O. Box 1150, SE-164 26 Kista, Sweden. Phone +46 08 626 63 00, Fax +46 8 754 56 66.

Munters Corporation 2691 Ena Drive Lansing, MI 48917 U.S.A. Phone +1 800-227-2376, Fax +1 517-676-7078

www.munters.us

Australia Munters Pty Limited, Phone +61 2 6025 6422, Brazil Munters Brasil Industria e Comercio Ltda, Phone +55 41 3317 5050, Canada/US Munters

Corporation Lansing, MI Phone +1 517 676 7070,

China Munters Air Treatment Equipment (Beijing) Co. Ltd, Phone +86 10 80 481 121, Denmark Munters A/S,

Phone +45 9862 3311,

India Munters India, Phone +91 20 3052 2520, Indonesia Munters, Phone +62 818 739 235, Italy Munters Italy S.p.A., Chiusavecchia,

Phone +39 0183 52 11,

Japan Munters K.K., Phone +81 3 5970 0021, Korea Munters Korea Co. Ltd., Phone +82 2 761 8701, Mexico Munters Mexico, Phone

+52 818 262 54 00,

Russia Munters AB, Phone +7 812 448 5740, Singapore Munters Pte Ltd., Phone +65 744 6828, South Africa and Sub-Sahara Countries

Munters (Pty) Ltd., Phone +27 11 997 2000, Spain Munters Spain S.A., Phone +34 91 640 09 02, Sweden Munters AB, Phone +46 8 626 63 00, Thailand

Munters Co. Ltd., Phone +66 2 642 2670, Turkey Munters Form Endüstri Sistemleri A.Ş, Phone +90 322 231 1338, USA Munters Corporation Lansing, MI Phone

+1 517 676 7070,

Vietnam Munters Vietnam, Phone +84 8 3825 6838, Export & Other countries Munters Italy S.p.A., Chiusavecchia Phone +39 0183 52 11

ZEWP2900 Reventa Inlets are Sold by Munters Corporation Lansing, Michigan U.S.A. 1-800-227-2376

Munters ZEW Profi Inlet Owner's manual

Munters ZEW Profi Inlet Owner's manual

Munters ZEW Profi Inlet Owner's manual

Related papers

Other documents