Delta Core TYBOX 237 User manual

Type
User manual

This manual is also suitable for

www.deltadore.com
AUTO
PROG
TYBOX 217 - 227 - 237 - 327 - 337
08/19
> 3s
PROG
5+2
PROG
PROG
x7
Important product
information ()
1
31
1
12
0
23
0
59
2012 ...
EXIT
1
2
3
4
5
8
9
10
11
6
7
6.00
16°C 16°C
20°C 20°C 20°C
18°C 18°C
8.00 11.00 13.00
17.00
23.000.00
P1
P2 P3 P4 P5 P6
6.00
16°C 16°C
20°C
23.000.00
P1
P6
TYBOX 3x7
h (ON)
023
4
5
i
STOP
1
31
5°C
15°C
18/02/2012
00.00
Time setting
Turn the selector dial to .
The days ash.
Press + or - to select the day, then press OK
to conrm and move on to the next setting.
Repeat the process to set
the hours and minutes.
In AUTO mode, pressing the i button displays the room temperature or the temperature setting,
depending on the conguration during installation.
Operating hours counter (boiler)
Room temperatureSet-point temperature
Information button
Interval before maintenance
of the boiler
Return to
automatic mode
Turn the selector dial to AUTO.
Your thermostat follows the programme.
Depending on the conguration during installation,
your device will constantly display the temperature
setting or the room temperature. To change these
settings, refer to the»installation guide» or contact
your installation engineer.
This mode protects your home from frost if you are absent for several days.
Turn the selector dial
and enter the return date.
This mode is used to switch your heating
installation off. Turn the selector dial to .
In this mode, the device displays the room
temperature.
Enter the return date
The Frost Protection
setting is adjustable
(§ «Setting
temperatures»).
To change the mode in progress, press OK again.
To cancel the current absence mode, turn the selector dial.
Conrm
Conrm
Return to AUTO
mode at the end of
the countdown, at
00:00.
Press me /
Program «Once» /
Weekly programming /
2 daily programs (week + week-end) /
TYBOX follows the program «Once».
Countdown
The Frost Protection
setting is adjustable
PROG
1
3
4
2
Alkalines 1,5V
LR03 (AAA)
1
7
P1
P6
5°C
30°C
00:00
23:45
P1
P6
6.00 8.0011.00 13.00
17.00
23.000.00
P1
P2 P3 P4 P5 P6
PROG x7
PROG
6.00
16°C 16°C
19°C 20°C 20°C
18°C 18°C
8.00 11.00 13.00
17.00
23.000.00
P1
P2 P3 P4 P5 P6
16°C 16°C
20°C 20°C
18°C 18°C
5°C
30°C
00:00
23:45
00:00
23:45
PROG 5+2
1
2
1
2
3
1...5
6/7
1
2
3
4
5
6
7
8
9
3
7.00
16°C 16°C20°C
23.000.00
P1
P6
1
3
2
PROG 5+2
EXIT
EXIT
EXIT
PROG x 7
A
B
COPY
OR
>3s
6.00
16°C
16°C
20°C 20°C 20°C
18°C
8.00 11.00 13.00
13.54
17.00 23.000.00
P1
P2 P3 P4 P5 P6
13.54
AUTO
PROG
7.00
16°C 16°C20°C
23.000.00
P1
P6
21°C
18°C
When the batteries symbol appears. you have
approximately 1 month to change the batteries
(2 1.5 V LR03 or AAA alkaline batteries).
You have approximately 30 seconds to change
the batteries before the time setting is reset
(if this happens, reprogramme the date and time).
Override
From AUTO mode or the «day at home» programme
Allows a given temperature setting to be applied until the next change of programme.
Conrm and continue on to the next day to program
it separately or conrm the program and copy it to
the next day.
E.g.
The program can be modied for each day.
Use the + and - buttons to make your choices.
Press OK to conrm and move on to the next setting
2 daily programmes: week (1 to 5) + weekend (6 and 7).
1 single programme for the 5 weekdays.
1 single programme for the weekend.
To change the programme, see above.
To apply a simplied program (two programmable periods, P1 and P6). This program can be modied.
To exit the mode,
turn the selector dial.
To exit the mode,
turn the selector dial.
Periods 2 to 5 can be disabled.
e.g. disabling of the midday slot (periods 3 and 4).
Select the programme stage to be disabled
(e.g.: P3)
Repeatedly press the - button until the display
shows «--:--»
Conrm by pressing OK.
Repeat the operation for each time slot of
the programme that you wish to disable.
The programme may be weekly (PROG x7) or
daily (PROG 5+2). This choice is made using the switch
on the back of the device.
This programming can also be done in one-hour,
half-hour, or quarter-hour stages.
If you wish to change these settings, refer to the
«installation guide» or contact your installation engineer.
Programming can be done for one-hour, 30-minute or 15-minute
time slots (see «installation guide», menu 1-02).
Turn the selector dial to PROG
Press the - button to display the ashing symbol
Conrm by pressing OK
Congure the «day at home» programme using the + and - buttons,
then press OK to conrm and move on to the next setting.
  • Page 1 1
  • Page 2 2

Delta Core TYBOX 237 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI