1
CAUTION...............WARNING...............IMPORTANT
USE ONLY A PETERSON REAL FYRE G10 BURNER WITH THIS REAL FYRE LOG SET.
Important: Adequate spacing between the
logs is NECESSARY and MUST be
maintained. If carbon build up (sooting)
exists, correct log placement before
sooting becomes worse. If any sooting
occurs outside of the firebox (i.e. on
the walls), turn off unit immediately
and contact a qualified professional
service technician.
WARNING: Use ONLY a Peterson Real Fyre
G10 burner with this Real Fyre gas log
set. Failure to do so may result in
property damage or personal injury,
and will void listings, certifications,
and invalidate claims made to RHP.
Contact your local Real Fyre dealer if you
need more information.
This instruction contains log set placement for these Real Fyre logs. You must position and maintain the log
layout as shown here to ensure proper operation of the burner system. Incorrect log installation could cause
flame impingement and improper combustion, resulting in soot and/or excessive by-products of combustion.
DO NOT add any additional embers for this installation. Any additional embers will cause unsafe operation.
Use these logs only with a Peterson G10 burner system.
If you experience an accumulation of black carbon (soot) on your logs it is an indication of incomplete
combustion and you must correct the log placement as instructed in this manual. If significant sooting
continues, stop using this gas log set.
Please read these instructions completely and carefully.
This product is only warranted when used as part of a
Robert H. Peterson Co. unvented burner system.
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
LOG SET IMPORTANT INFORMATION
L-F2-136
REV 0 - 2004170940
CHARRED GNARLED SPLIT & GNARLED OAK LOG PLACEMENT INSTRUCTIONS
CHGS-24 shown
2
Failure to use a Peterson G10 burner may result in a DANGEROUS
situation and in property damage, personal injury or even death, will void
listings and certifications, and will void any insurance coverage by R.H.
Peterson Co. or our insurers.
CAUTION: Burn hazard! Logs will remain hot for some time after use.
If you need to reposition any log to maintain the proper layout,
use heat resistant gloves or allow logs adequate time to cool
before handling.
WARNING: This gas log set is for use with an R.H. Peterson Co. G10
burner (and parts) ONLY.
L-F2-136
REV 0 - 2004170940
3
CHARRED GNARLED SPLIT & GNARLED OAK LOG PLACEMENT INSTRUCTIONS (16/18" MODEL)
III
I
II
CHGS-16/18 & GNO-16/18
PARTS LIST
All items for this log set are included in one (1) box.
CAUTION: Burn hazard! Logs will remain hot
for some time after use.
1
2
CHGSL-15BR
CHGSL-16/18BF
GNOL-16/18BF
3
CHGSL-11TC
GNOL-10TR
5
4
CHGSL-11TR
GNOL-10TL
CHGSL-11TL
GNOL-10TC
Place the rear log (log #1) as shown. Slide it forward
on the grate, against the main burner bracket. The
cutouts found on the underside of the log should
align over the grate fingers. ENSURE THE LOG
RESTS FLAT ON THE BURNER/GRATE.
2
Place the front log (log #2) as shown. Slide it back
on the grate, against the main burner bracket. The
cutouts found on the underside of the log should
align over the grate fingers. ENSURE THE LOG
RESTS FLAT ON THE BURNER/GRATE.
Ensure the rear and front logs are snug up against
the main burner bracket.
1
Logs snug against bracket
The underside of the bottom logs have cutouts and tabs that align over the burner. THE BOTTOM LOGS
MUST BE FULLY SEATED ON THE BURNER. Certain logs have notches on them to allow for the logs to
interlock in place.
Select G10 burner systems include a
decorative wood chip. If equipped, refer
to the INSTALLATION section of the main
owner’s manual supplied with the burner for
placement.
IV
Place the left middle log (log #3) as shown. The
log should lock in place over the logs below.
CHGSL-9T
GNOL-8T
6
3
CHGS-16/18 log set shown
4
CHARRED GNARLED SPLIT & GNARLED OAK LOG PLACEMENT INSTRUCTIONS (16/18" MODEL) (CONT.)
V
VI
Place the center middle log (log #4) as shown.
The log should lock in place over the logs below.
Place the center top log (log #5) as shown. The log
should lock in place over the logs below.
Place the left top log (log #6) as shown. The log
should lock in place over the logs below.
After setting the logs into position as described above, ensure each is properly and firmly seated. The
vent-free gas log set will not function as intended if the logs are not correctly positioned. When placed
properly, the flames will not strike any portion of the logs. Periodically check the positioning of all logs to
ensure proper log placement and stability. If any flame is striking the logs, recheck log placement. Adjust
to conform with instructions. There should be no flame impingement on the logs.
6
5
4
5
CHARRED GNARLED SPLIT & GNARLED OAK LOG PLACEMENT INSTRUCTIONS (24" & 30" MODELS)
III
I II
IV
CHGS-24, CHGS-30, GNO-24, & GNO-30
PARTS LIST
CHGS-24 log set shown
1
2
4
3
5
6
24" - CHGSL-20BR
30" - CHGSL-21BR
24" - CHGSL-24BF
24" - GNOL-24BF
30" - CHGSL-30BF
30" - GNOL-30BF
CHGSL-12TL
GNOL-12TL
CHGSL-10T
GNOL-10T
Place the rear log (log #1) as shown. Slide it forward on
the grate, against the main burner bracket. The cutouts
found on the underside of the log should align over the
grate fingers. ENSURE THE LOG RESTS FLAT ON THE
BURNER/GRATE.
2
Place the front log (log #2) as shown. Slide it back on the
grate, against the main burner bracket. The cutouts found on
the underside of the log should align over the grate fingers.
ENSURE THE LOG RESTS FLAT ON THE BURNER/
GRATE.
Ensure the rear and front logs are snug up against the main
burner bracket.
Place the left middle log (log #3) as shown. The log should
lock in place over the logs below.
Place the center middle log (log #4) as shown. The log
should lock in place over the logs below.
CHGSL-10TC
GNOL-11TC
8
CHGSL-12TR
GNOL-11TR
CHGSL-11T
GNOL-11T
1
Logs snug against bracket
The underside of the bottom logs have cutouts and tabs that align over the burner. THE BOTTOM LOGS
MUST BE FULLY SEATED ON THE BURNER. Certain logs have notches on them to allow for the logs to
interlock in place.
All items for this log set are included in one (1) box.
CAUTION: Burn hazard! Logs will remain hot
for some time after use.
Select G10 burner systems include a
decorative wood chip. If equipped, refer
to the INSTALLATION section of the main
owner’s manual supplied with the burner for
placement.
3 4
CHGSL-9T
GNOL-8T
7
6
After setting the logs into position as described above, ensure each is properly and firmly seated. The
vent-free gas log set will not function as intended if the logs are not correctly positioned. When placed
properly, the flames will not strike any portion of the logs. Periodically check the positioning of all logs to
ensure proper log placement and stability. If any flame is striking the logs, recheck log placement. Adjust
to conform with instructions. There should be no flame impingement on the logs.
CHARRED GNARLED SPLIT & GNARLED OAK LOG PLACEMENT INSTRUCTIONS (24" & 30" MODELS) (CONT.)
Place the center top log (log #5) as shown. The log
should lock in place over the logs below.
Place the right middle log (log #6) as shown. The
log should lock in place over the logs below.
V
VI
Place the inner-left middle log (log #7) as shown.
The log should lock in place over the logs below.
Place the inner-right middle log (log #8) as shown.
The log should lock in place over the logs below.
6
7
5
8
-
1
-
2
-
3
-
4
-
5
-
6
Real Fyre G10 Charred Gnarled Split Log Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Real Fyre G8 Owner's manual
-
-
-
-
-
-
-
-
-