Toro Roller Striping Kit, Z Master TURBO FORCE Mowers Installation guide

Brand: Toro

Model: Roller Striping Kit, Z Master TURBO FORCE Mowers

Type: Installation guide

Form No. 3355-906 Rev A

Roller Striping Kit

For Z Master® TURBO FORCE® Mowers

Model No. 108-2162

Installation Instructions

Safety

Safety and Instructional Decals

Safety decals and instr uctions are easily visible to the operator and are located near any

area of potential dang er . R e place any decal that is damag ed or lost.

108-4108

1. Striping roller 3. Raise the striping roller.

2. Engage the striping roller.

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

Flange bushing

Roller assembly

Bolt (3/8 x 4-3/4 inches)

Washer

Spacer 2

Right-hand spring

Left-hand spring

Locknut (3/8 inch)

Install the roller.

Control lever assembly

Bolt (7/16 x 2 inches)

Flange nut (7/16 inch)

Locknut (3/8 inch)

Install the control lever assembly.

Note: Deter mine the left and right sides of the

mac hine from the nor mal operating position.

Step

Installing the Roller

Parts needed for this step:

Flange bushing

Roller assembly

Bolt (3/8 x 4-3/4 inches)

Washer

2 Spacer

Right-hand spring

Left-hand spring

Locknut (3/8 inch)

Procedure

1. Inser t a ﬂang e bushing into the front hole of

eac h brac k et on the bac k of the mo w er ( Figure

1 ).

Figure 1

1. Roller assembly 3. Flange bushing

2. Rear of the mower deck

(viewed from the front)

2. T hread a w asher , spacer , and spring (with the

long end to w ard the bolt head) onto eac h bolt

(3/8 x 4-3/4 inc hes) ( Figure 2 )

Figure 2

1. Bolt (3/8 x 4-3/4 inches)

5. Left-hand spring

2. Washer

6. Locknut (3/8 inch)

3. Spacer

7. Roller assembly

4. Right-hand spring

3. Place the roller assembly around the brac k ets

and ﬂang e bushings at the rear of the mo w er

( Figure 1 )

Important: T he ﬂange of each ﬂange

bushing should be betw een the mo w er

brack et and the r oller assembl y brack et

with the body of the bushings extending

thr ough the mo w er brack ets.

4. Secure the roller assembly with the bolt

assemblies and 2 n uts (3/8 inc h) as illustrated

in Figure 2 .

Important: Ensur e that y ou install the

springs as sho wn in Figur e 2 . T he springs

ar e opposites of each other , one meant f or

the right side and one f or the left. Ensur e

that the long end of each spring is on the

top of the r oller assembl y and the shor t end

is ang led up a gainst the deck.

Step

Installing the Control Lever

Assembly

Parts needed for this step:

Control lever assembly

Bolt (7/16 x 2 inches)

Flange nut (7/16 inch)

Locknut (3/8 inch)

Procedure

1. R emo v e the bolt and n uts securing the left rear

mo w er dec k mounting c hain to the mo w er

dec k.

2. Install the control lev er assembly onto the

brac k et y ou remo v ed the c hain from, securing

it and the dec k mounting c hain with a bolt

(7/16 x 2 inc hes) and 2 ﬂang e n uts (7/16 inc h)

( Figure 3 ).

Figure 3

1. Bolt (7/16 x 2 inches)

5. Connect the control lever

assembly chain here

2. Flange nut (7/16 inch) 6. Locknut (3/8 inch)

3. Control lever assembly 7. Chain

4. Flange nut (7/16 inch)

8. Last link of the chain

installed between the

locknuts

3. T hread a loc kn ut (3/8 inc h) onto the bolt on

the left of the roller assembly ( Figure 3 ).

4. Connect the last link of the c hain on the

control lev er assembly to the bolt on the left of

the roller assembly using a loc kn ut (3/8 inc h),

securing the c hain betw een the loc kn uts near

the top of the bolt ( Figure 3 ).

5. T est the lev er action b y mo ving it bac k and

for th.

T he roller should lift up and do wn.

Toro Roller Striping Kit, Z Master TURBO FORCE Mowers Installation guide

Toro Roller Striping Kit, Z Master TURBO FORCE Mowers Installation guide

Toro Roller Striping Kit, Z Master TURBO FORCE Mowers Installation guide

Related papers

Other documents