IPT Sink Company IPTAP6040SP7556CP Installation guide
- Type
- Installation guide
PAGE 1
Apron Front Stainless Steel Sink
Installation Instructions
Before You Start
• IPT Sink Company recommends that all apron front sinks should be installed by an experienced, professional installer.
• IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is
recommended that you discuss with your installer and agree that the nished appearance is the desired effect. IPT Sink Company is
not responsible for improper sink or countertop installations.
• IMPORTANT: The cabinet must be installed, secured, plumb, and level. The front sink apron must be secured to the front of the
cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product
damage.
• IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but
short enough not to go through the walls of adjacent cabinets.
• IPT Sink Company apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
• A custom sink base cabinet and support framing is required for proper installation. IPT Sink Company recommends providing the
cabinet maker with the actual sink to be installed prior to cabinet fabrication.
• IPT Sink Company is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage
prior to beginning installation.
• Metal edges may be sharp – use caution when handling.
• Follow all local plumbing and building codes.
Recommended Tools & Materials (Not Included)
Tape Measure
Safety Glasses
Painter’s Tape
Saw
Level
Framing Square
Pencil (not permanent marker)
Shims or Cabinet Fillers
Denatured Alcohol
Clamps
Construction Adhesive
Silicone Sealant
Support Framing Material (1 ¼” (32mm) Max Thickness)
Screws (recommended by countertop manufacturer)
PAGE 1
Apron Front Stainless Steel Sink
Installation Instructions
Before You Start
• Soleil recommends that all apron front sinks should be installed by an experienced, professional installer.
• IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is
recommended that you discuss with your installer and agree that the finished appearance is the desired effect. Soleil is not
responsible for improper sink or countertop installations.
• IMPORTANT: The cabinet must be installed, secured, plumb, and level. The front sink apron must be secured to the front of the
cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product
damage.
• IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but
short enough not to go through the walls of adjacent cabinets.
• Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
• A custom sink base cabinet and support framing is required for proper installation. Soleil recommends providing the cabinet
maker with the actual sink to be installed prior to cabinet fabrication.
• Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to
beginning installation.
• Metal edges may be sharp – use caution when handling.
• Follow all local plumbing and building codes.
Recommended Tools & Materials (Not Included)
� Tape Measure
� Safety Glasses
� Painter’s Tape
� Saw
� Level
� Framing Square
� Pencil (not permanent marker)
� Shims or Cabinet Fillers
� Denatured Alcohol
� Clamps
� Construction Adhesive
� Silicone Sealant
� Support Framing Material (1 ¼” (32mm) Max Thickness)
� Screws (recommended by countertop manufacturer)
Single Bowl Kitchen Sink 50/50 Double Bowl Kitchen Sink 60/40 Double Bowl Kitchen Sink
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
PAGE 1
Apron Front Stainless Steel Sink
Installation Instructions
Before You Start
• Soleil recommends that all apron front sinks should be installed by an experienced, professional installer.
• IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is
recommended that you discuss with your installer and agree that the finished appearance is the desired effect. Soleil is not
responsible for improper sink or countertop installations.
• IMPORTANT: The cabinet must be installed, secured, plumb, and level. The front sink apron must be secured to the front of the
cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product
damage.
• IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but
short enough not to go through the walls of adjacent cabinets.
• Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
• A custom sink base cabinet and support framing is required for proper installation. Soleil recommends providing the cabinet
maker with the actual sink to be installed prior to cabinet fabrication.
• Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to
beginning installation.
• Metal edges may be sharp – use caution when handling.
• Follow all local plumbing and building codes.
Recommended Tools & Materials (Not Included)
� Tape Measure
� Safety Glasses
� Painter’s Tape
� Saw
� Level
� Framing Square
� Pencil (not permanent marker)
� Shims or Cabinet Fillers
� Denatured Alcohol
� Clamps
� Construction Adhesive
� Silicone Sealant
� Support Framing Material (1 ¼” (32mm) Max Thickness)
� Screws (recommended by countertop manufacturer)
Single Bowl Kitchen Sink 50/50 Double Bowl Kitchen Sink 60/40 Double Bowl Kitchen Sink
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
PAGE 1
Apron Front Stainless Steel Sink
Installation Instructions
Before You Start
• Soleil recommends that all apron front sinks should be installed by an experienced, professional installer.
• IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is
recommended that you discuss with your installer and agree that the finished appearance is the desired effect. Soleil is not
responsible for improper sink or countertop installations.
• IMPORTANT: The cabinet must be installed, secured, plumb, and level. The front sink apron must be secured to the front of the
cabinet by attaching fasteners through the cabinet front and into the support framing. Failure of this step can lead to product
damage.
• IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws are long enough to secure the support framing, but
short enough not to go through the walls of adjacent cabinets.
• Soleil apron front sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
• A custom sink base cabinet and support framing is required for proper installation. Soleil recommends providing the cabinet
maker with the actual sink to be installed prior to cabinet fabrication.
• Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to
beginning installation.
• Metal edges may be sharp – use caution when handling.
• Follow all local plumbing and building codes.
Recommended Tools & Materials (Not Included)
� Tape Measure
� Safety Glasses
� Painter’s Tape
� Saw
� Level
� Framing Square
� Pencil (not permanent marker)
� Shims or Cabinet Fillers
� Denatured Alcohol
� Clamps
� Construction Adhesive
� Silicone Sealant
� Support Framing Material (1 ¼” (32mm) Max Thickness)
� Screws (recommended by countertop manufacturer)
Single Bowl Kitchen Sink 50/50 Double Bowl Kitchen Sink 60/40 Double Bowl Kitchen Sink
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
Single Bowl Kitchen Sink 50/50 Double Bowl Kitchen Sink 60/40 Double Bowl Kitchen Sink
Contact IPT Sink Company at (678) 445-4638 or visit www.iptsink.com. Copyright ©2016, IPT Sink Company Inc. All rights reserved.
Apron Front Stainless Steel Sink
Installation Instructions
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Mark the front apron cut out on the painter’s tape using the dimension
of the apron front.
3. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level
BEFORE installing the sink.
IMPORTANT: IPT Sink Company recommends providing the cabinet maker with
the actual sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
make any necessary adjustments by either adding ller strips or sanding the
opening.
Apron Front Stainless Steel Sink
Installation Instructions
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level
BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
make any necessary adjustments by either adding filler strips or sanding the
opening.
Apron Front Stainless Steel Sink
Installation Instructions
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level
BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
make any necessary adjustments by either adding filler strips or sanding the
opening.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: INSTALL SUPPORT FRAMING
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws
(not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
Apron Front Stainless Steel Sink
Installation Instructions
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level
BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
make any necessary adjustments by either adding filler strips or sanding the
opening.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: INSTALL SUPPORT FRAMING
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws
(not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
3: INSTALL SUPPORT FRAMING
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws
(not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
PAGE 2
Apron Front Stainless Steel Sink
Installation Instructions
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level
BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
make any necessary adjustments by either adding filler strips or sanding the
opening.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: INSTALL SUPPORT FRAMING
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws
(not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
countertop, ush to the front and centered; secure with tape.
2. Trace the template and remove. Dry t the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
Apron Front Stainless Steel Sink
Installation Instructions
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level
BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
make any necessary adjustments by either adding filler strips or sanding the
opening.
Apron Front Stainless Steel Sink
Installation Instructions
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level
BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
make any necessary adjustments by either adding filler strips or sanding the
opening.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: INSTALL SUPPORT FRAMING
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws
(not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
Apron Front Stainless Steel Sink
Installation Instructions
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level
BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
make any necessary adjustments by either adding filler strips or sanding the
opening.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: INSTALL SUPPORT FRAMING
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws
(not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
3: INSTALL SUPPORT FRAMING
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws
(not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
PAGE 2
Apron Front Stainless Steel Sink
Installation Instructions
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level
BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
make any necessary adjustments by either adding filler strips or sanding the
opening.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: INSTALL SUPPORT FRAMING
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws
(not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
3: INSTALL SUPPORT FRAMING
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
horizontal supports to the oor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws
(not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
PAGE 2
Apron Front Stainless Steel Sink
Installation Instructions
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level
BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
make any necessary adjustments by either adding filler strips or sanding the
opening.
Apron Front Stainless Steel Sink
Installation Instructions
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level
BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
make any necessary adjustments by either adding filler strips or sanding the
opening.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: INSTALL SUPPORT FRAMING
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws
(not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
Apron Front Stainless Steel Sink
Installation Instructions
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level
BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
make any necessary adjustments by either adding filler strips or sanding the
opening.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: INSTALL SUPPORT FRAMING
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws
(not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
3: INSTALL SUPPORT FRAMING
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws
(not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
PAGE 2
Apron Front Stainless Steel Sink
Installation Instructions
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
cabinet, flush to the top and centered; secure with tape.
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level
BEFORE installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
make any necessary adjustments by either adding filler strips or sanding the
opening.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
countertop, flush to the front and centered; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
3: INSTALL SUPPORT FRAMING
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
horizontal supports to the floor of the cabinet.
6. Secure the vertical supports with construction adhesive and screws
(not provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
PAGE 2
hts reserved.
1: PREPARE THE BASE CABINET
1. Apply painter’s tape to the cabinets for marking and cutting purposes.
This will protect the cabinet from damage while cutting.
2. Position the template (provided with your sink) on the front of the
3. Trace the template and remove.
4. Using a sharp saw blade, carefully cut the cabinet on the traced line.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil recommends providing the cabinet maker with the actual
sink prior to cabinet fabrication. Before installing the sink, verify that the
distance from the top of the doors to the top of the cabinet is greater than the
apron front.
IMPORTANT: Double check the measurement of the cabinet cutout and
opening.
OUTLINE FOR APRON
FRONT SINK CUTOUT
1. Cut two lengths of support framing to extend horizontally along the
inside walls on each side of the cabinet.
2. Measure and mark the support mounting locations; ensure the sink rim
will sit at or slightly below the top of the cabinet.
3. Position and level the supports.
4. Secure the supports with construction adhesive and screws (not
provided).
5. Cut (4) lengths of support framing to extend from the bottom of the
6. Secure the vertical supports with construction adhesive and screws (not
provided).
IMPORTANT: Long screws may damage adjacent cabinets. Ensure the screws
are long enough to secure the support framing, but short enough not to go
through the walls of adjacent cabinets.
IMPORTANT: A custom sink base cabinet and support framing is required for
proper installation.
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
SUPPORT FRAMING SHOULD BE RECESSED SO THE
SINK FITS FLUSH WITH THE TOP OF THE CABINET
3: INSTALL SUPPORT FRAMING
2: PREP COUNTERTOP
1. Position the template (provided with your sink) on the bottom of the
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the traced line.
OUTLINE FOR APRON
FRONT SINK CUTOUT
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
Contact IPT Sink Company at (678) 445-4638 or visit www.iptsink.com. Copyright ©2016, IPT Sink Company Inc. All rights reserved.
Apron Front Stainless Steel Sink
Installation Instructions
PAGE 3
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by
the frame.
2. Push the sink in to ensure the apron is ush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: IPT Sink Company is not responsible for sink or countertop if
damaged during installation. Be sure to inspect the sink for damage prior to
beginning installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
Apron Front Stainless Steel Sink
Installation Instructions
PAGE 3
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by
the frame.
2. Push the sink in to ensure the apron is flush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
Apron Front Stainless Steel Sink
Installation Instructions
PAGE 3
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by
the frame.
2. Push the sink in to ensure the apron is flush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by the
frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
5: INSTALL COUNTERTOP
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETS
THE COUNTERTOP AND CABINET.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
with your installer and agree that this nished appearance is the desired eect.
5: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top flange (or lip) of the
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this with
your installer and agree that this finished appearance is the desired effect.
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by the
frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
5: INSTALL COUNTERTOP
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETS
THE COUNTERTOP AND CABINET.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
with your installer and agree that this nished appearance is the desired eect.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
5: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top flange (or lip) of the
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this with
your installer and agree that this finished appearance is the desired effect.
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
Apron Front Stainless Steel Sink
Installation Instructions
PAGE 3
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by
the frame.
2. Push the sink in to ensure the apron is flush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by the
frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
5: INSTALL COUNTERTOP
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETS
THE COUNTERTOP AND CABINET.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
with your installer and agree that this nished appearance is the desired eect.
5: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top flange (or lip) of the
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this with
your installer and agree that this finished appearance is the desired effect.
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by the
frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
5: INSTALL COUNTERTOP
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETS
THE COUNTERTOP AND CABINET.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
with your installer and agree that this nished appearance is the desired eect.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
4170 JVL Industrial Park Drive
Marietta, GA 30066
(678) 445-4638
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
5: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top ange (or lip) of the
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this with
your installer and agree that this nished appearance is the desired effect.
IPT Sink Company is not responsible for improper sink or countertop installations.
IMPORTANT: IPT Sink Company apron front sinks should only be fastened to a
solid surface countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
Apron Front Stainless Steel Sink
Installation Instructions
PAGE 3
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by
the frame.
2. Push the sink in to ensure the apron is flush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
Apron Front Stainless Steel Sink
Installation Instructions
PAGE 3
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by
the frame.
2. Push the sink in to ensure the apron is flush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by the
frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
5: INSTALL COUNTERTOP
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETS
THE COUNTERTOP AND CABINET.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
with your installer and agree that this nished appearance is the desired eect.
5: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top flange (or lip) of the
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this with
your installer and agree that this finished appearance is the desired effect.
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by the
frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
5: INSTALL COUNTERTOP
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETS
THE COUNTERTOP AND CABINET.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
with your installer and agree that this nished appearance is the desired eect.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
5: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top flange (or lip) of the
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this with
your installer and agree that this finished appearance is the desired effect.
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
Apron Front Stainless Steel Sink
Installation Instructions
PAGE 3
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by
the frame.
2. Push the sink in to ensure the apron is flush to the front of the cabinet.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided.
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp - use caution when handling.
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by the
frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
5: INSTALL COUNTERTOP
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETS
THE COUNTERTOP AND CABINET.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
with your installer and agree that this nished appearance is the desired eect.
5: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top flange (or lip) of the
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this with
your installer and agree that this finished appearance is the desired effect.
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
4: INSTALL THE SINK
1. Lower the sink onto the supports and verify the sink is supported by the
frame.
2.
3. Verify the sink is level. Make any adjustments and shim as needed.
4. Secure the sink in place using the hardware provided
IMPORTANT: The front sink apron must be secured to the front of the cabinet
by attaching fasteners through the cabinet front and into the support framing.
Failure of this step can lead to product damage.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
IMPORTANT: Metal edges may be sharp – use caution when handling.
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant around the side and
back of the sink.
3. Carefully position and secure the sink to the countertop following the
manufacturer’s instructions.
4. Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
5. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil apron front sinks should only be fastened to a solid surface
countertop (i.e. granite, Corian® or Silestone®).
IMPORTANT: Make sure the top of the sink does not extend above the top of the
cabinet; otherwise it will interfere with countertop installation.
5: INSTALL COUNTERTOP
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
APPLY SILICONE SEALANT WHERE THE SINK MEETS
THE COUNTERTOP AND CABINET.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Apron Front Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 3
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
with your installer and agree that this nished appearance is the desired eect.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
4170 JVL Industrial Park Drive
Marietta, GA 30066
(678) 445-4638
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
6: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.iptsink.com or contact IPT Sink Company directly at:
IPT Sink Company Inc.
4170 JVL Industrial Park Drive
Marietta, GA 30066
(678) 445-4638
Contact IPT Sink Company at (678) 445-4638 or visit www.iptsink.com. Copyright ©2016, IPT Sink Company Inc. All rights reserved.
Limited Lifetime Sink Warranty
This product has been manufactured and tested to the highest quality standards by IPT Sink Company. We
offer our customers thoughtfully crafted xtures & accessories, engineered for enduring performance over
years of use.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original purchaser only. This warranty is not transferable, between homes or
owners and is only applicable to residential use.
WHAT IS COVERED BY THE WARRANTY
IPT Sink Company warranties this product against defects due to material or craftsmanship error during the
warranty period: IPT Sink Company will provide replacement parts at no charge, or at its option, replace
any product or part of the product that is deemed defective, under normal installation, use, service and
maintenance. If IPT Sink Company is unable to provide a replacement and repair is not practical or cannot
be made in a timely fashion, IPT Sink Company may elect to refund the purchase price in exchange for the
return of the product.
CONDITIONS AND EXCLUSIONS
Like other home xtures, IPT Sink Company products will require light maintenance to ensure proper
function. We provide you with complete knowledge to perform this maintenance and can also
recommend resources if you are unable to fulll this service.
A. IPT Sink Company will not be responsible for product failures due to lack of maintenance or proper use.
Please read your care and maintenance documentation to determine the limits of proper use.
B. The original sales receipt, order number, and/or proof of purchase must be presented at the time of the
warranty claim, without exception, for this warranty to be applied to all IPT Sink Company products.
C. IPT Sink Company recommends installing all IPT Sink Company products with a licensed, professional
plumber. IPT Sink Company will not be held responsible for any damage or product failure due to improper
installation, misuse, or failure to use a licensed professional. Please read your care and maintenance docu-
mentation to determine the limits of proper use.
D. Commercial use will automatically void this warranty.
NON-APPLICABILITY OF THIS WARRANTY
By the purchase and use of our products, you agree that IPT Sink Company is not liable for incidental,
consequential or special damages associated with the return, replacement, installation or use of your prod-
uct. This includes freight costs, cartridge replacement, labor, travel time, lost prot, home damages and
other contingent liabilities and costs (including, without limitation, costs associated with experts,
investigations, analyses, attorneys and other professionals and services). The IPT Sink Company warranty is
a comprehensive and explicit limit of liability and all items outside of it are not addressable by or the
responsibility of IPT Sink Company. Certain states have variances regarding implied warranties and in those
situations we remain fully compliant.
IPT Sink Company makes no implication that products comply with any or all local building or plumbing
codes. It is the consumer’s responsibility to determine local code compliance. This warranty extends to the
original purchaser and rst consumer.
For additional information or warranty issues visit www.iptsink.com or contact IPT Sink Company
directly: PHONE (678) 445-4638
PAGE 4
Contact IPT Sink Company at (678) 445-4638 or visit www.iptsink.com. Copyright ©2016, IPT Sink Company Inc. All rights reserved.
-
1
-
2
-
3
-
4
IPT Sink Company IPTAP6040SP7556CP Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
IPT Sink Company IPTFC33FLT Installation guide
-
IPT Sink Company IPTAP6040SP7556CP Installation guide
-
IPT Sink Company IPTDP50EP7556 Installation guide
-
IPT Sink Company IPTLXSBLP7636 Installation guide
-
IPT Sink Company IPTSBE3121P36BK Installation guide
-
IPT Sink Company IPTGR3321SB-MOC Installation guide
-
IPT Sink Company IPT210W Installation guide
-
IPT Sink Company IPTGR33P56K-GRY User manual
-
-
Other documents
-
DECOLAV 1201 Cutout Template
-
Kingston Brass YGKFA301810DS Installation guide
-
Kingston Brass YGKFA361810BC Installation guide
-
Kingston Brass HGKFA361810SQ Installation guide
-
Schon SCAP505016 Installation guide
-
Golden Vantage KS0337 Installation guide
-
Karran EL-84 Installation guide
-
Cahaba CASC0098 Installation guide
-
-
YASINU YNSFS330-G Operating instructions
