EdgeStar CWF380DZ User manual

Category
Wine coolers
Type
User manual

This manual is also suitable for

ii
V2.4-12132019
Freestanding Wine Refrigerator
CWF380DZ
Owner’s Manual
For more information on other great EdgeStar products on the web, go to http://www.edgestar.com
i
Important Safety Information
Improper handling can cause serious damage to the EdgeStar Wine Refrigerator and / or injury
to the user. This Wine Refrigerator is designed for domestic indoor use only. Do not use the
unit for industrial or commercial use. Any other use may invalidate the warranty. Please
review the ratings label located on the rear panel of the unit for electrical and other technical
data related to this unit. The unit must be used in a properly grounded wall outlet.
Please read and follow the safety information listed below to reduce the risk of fire,
electric shock, or injury.
Electrical Safety
Do not exceed the power outlet ratings.
It is recommended the Wine Refrigerator be connected on its own circuit.
The unit must be installed in accordance with state and local electrical codes.
A standard electrical supply (115 V, 60Hz), that is properly grounded in accordance with the
National Electrical Code and local codes and ordinances is required.
Use outlets that cannot be turned off by a switch or pull chain.
Always turn the unit off and unplug it from the outlet when cleaning.
Unplug the unit if it is not going to be used for an extended period of time.
Do not operate the unit with a power plug missing the ground plug, a damaged cord, or a loose
socket.
Be sure the Wine Refrigerator is properly grounded.
Never plug or unplug the unit with wet hands.
Do not bypass, cut, or remove the grounding plug.
Do not use extension cords or power strips with this unit. You may need to contact your
electrician if it is necessary to use a longer cord or if you do not have a grounded outlet. Do not
modify the power cord’s length or share the outlet with other appliances.
Do not start or stop the unit by switching the circuit’s power on and off.
If the power cord is damaged, it must be replaced by the manufacturer or a qualified technician.
Never repair the unit while it is plugged in.
Immediately unplug the unit if it makes strange sounds, emits smells, or smoke comes out of it,
and contact customer service.
Do not remove any part of the casing unless you are instructed to do so by an authorized
technician.
You should never attempt to repair the unit yourself.
Contact customer service for service options if the unit needs service.
ii
Note: This owner’s manual is provided for reference use only. Specifications may change
without prior notice. Refer to the product label on the back of your Wine Refrigerator for the
latest technical information.
General Safety
To prevent back and other types of injuries, use at least two people to move and install the wine
refrigerator.
This appliance is not intended for use by persons, including children, with reduced physical,
sensory or mental capabilities, unless they have been given supervision or instruction concerning
the use of the appliance by the person(s) responsible for their safety.
Install the Wine Refrigerator in a well-ventilated area where the ambient temperature is above
50° F and below 95° F.
The temperature range for this refrigerator is optimized for wine storage. Perishable food items
may require a different storage environment.
Do not place hot or warm items into the refrigerator before they cool down to room temperature.
This unit is designed to be installed indoors, and protected from rain, sleet, snow, and / or
moisture.
This unit is not intended to be used by children.
Children should be supervised to ensure that they do not play with this product.
Never allow children to crawl inside the Wine Refrigerator. If you are disposing of the unit,
remove the door.
Do not use this appliance near flammable gas or combustibles, such as gasoline, benzene,
thinner, etc.
Do not place the unit near heat sources such as ovens, grills, or direct sunlight.
Only use in an upright position on a flat, level surface and provide proper ventilation.
Do not pinch or kink the power supply line between the unit and cabinet.
Do not leave any cleaning solutions in the unit.
Do not use solvent-based cleaning agents or abrasive solutions to clean the unit as they may
damage the interior and exterior.
Do not place any other appliances on top of the unit.
Do not turn the unit upside down, on its side, or at an angle off level.
If your model of wine refrigerator is equipped with a lock, take care to keep the keys away from
children.
Do not move the unit without emptying the contents and securing the door in a closed position.
Note: Flammable Refrigerant Used! When handling, moving, and using the refrigerator, make
sure to avoid either damaging the refrigerant tubing, or increasing the risk of a leak.
iii
Table of Contents
IMPORTANT SAFETY INFORMATION ..................................................................................................................... I
TABLE OF CONTENTS ........................................................................................................................................... III
FIRST TIME OPERATING INSTRUCTIONS ......................................................................................................................... 4
INTRODUCTION ........................................................................................................................................................ 4
PARTS IDENTIFICATION ......................................................................................................................................... 5
FRONT VIEW ................................................................................................................................................................ 5
BACK VIEW .................................................................................................................................................................. 5
Internal Fan ................................................................................................................................................................ 6
INSTALLING THE WINE REFRIGERATOR ............................................................................................................. 6
UNPACKING THE WINE REFRIGERATOR ......................................................................................................................... 7
INSTALLATION ............................................................................................................................................................... 7
Free-standing Installation: .......................................................................................................................................... 7
Installation Clearance Requirements ......................................................................................................................... 8
ELECTRICAL REQUIREMENTS ........................................................................................................................................ 9
Recommended Grounding Method ............................................................................................................................ 9
LEVELING THE WINE REFRIGERATOR ............................................................................................................................. 9
INSTALLING THE DOOR HANDLE ................................................................................................................................... 10
INSTALLING AND REMOVING THE SHELVES ................................................................................................................... 10
To Install the Shelves: .............................................................................................................................................. 10
To Remove the Shelves ........................................................................................................................................... 10
REVERSING THE DOOR SWING .................................................................................................................................... 11
To Reverse the Door from Right Swing to Left Swing ............................................................................................. 11
REMOVING AND INSTALLING DECORATIVE PLUGS ......................................................................................................... 13
OPERATION ............................................................................................................................................................ 14
INSTALLATION CHECK LIST BEFORE OPERATION .......................................................................................................... 14
USING THE TEMPERATURE CONTROL PANEL ................................................................................................................ 15
NORMAL SOUNDS ....................................................................................................................................................... 16
TEMPERATURE ALARM ................................................................................................................................................ 16
DOOR AJAR ALARM .................................................................................................................................................... 16
DEFROSTING .............................................................................................................................................................. 16
PREPARING THE WINE REFRIGERATOR FOR STORAGE ................................................................................................. 16
CLEANING AND MAINTENANCE .......................................................................................................................... 17
EXTERIOR CLEANING .................................................................................................................................................. 17
INTERIOR CLEANING ................................................................................................................................................... 17
TROUBLESHOOTING ............................................................................................................................................. 18
SPECIFICATIONS ................................................................................................................................................... 20
EDGESTAR LIMITED WARRANTY ........................................................................................................................ 21
4
First Time Operating Instructions
Before use, make sure all packaging labels and materials are removed from the unit. Be sure
to keep track of all included parts and pieces before discarding the packaging materials. It is
advised that you keep the original box and packaging materials in case you ever need to move
or ship the appliance in the future.
Let the unit stand for at least 24 hours before you use it; this allows the cooling components
time to settle from transit. The instruction manual should be read before use.
Introduction
Thank you for purchasing this EdgeStar Wine Refrigerator. We hope that this purchase will be
the beginning of a lasting and rewarding relationship between you and EdgeStar. We will
provide the customer support and exemplary products necessary to nurture that relationship.
This manual contains important information regarding the proper installation, use, and
maintenance of your Wine Refrigerator. Following this manual will ensure that your product will
work at its peak performance and efficiency.
Please save the original product packaging in case you need to safely transport your Wine Refrigerator.
For Your Records:
Please write down the model number and serial number below for future reference.
Both numbers are located on the ratings label on the back of your unit and are needed
to obtain warranty service. You may also want to staple your receipt to this manual as it
is the proof of your purchase, and is also needed for service under your warranty.
Model Number:
Serial Number:
Date of Purchase:
For a more efficient experience, please do the following before contacting customer service:
If you received a damaged product, immediately contact the retailer or dealer that sold you
the product.
Read and follow this instruction manual carefully to help you install, use, and maintain your
Wine Refrigerator.
Read the troubleshooting section of this manual as it will help you diagnose and solve
common issues.
Visit us on the web at http:/www.edgestar.com to register your product, download product
guides, and access additional troubleshooting resources and up-to-date information.
If you need warranty service, our friendly customer service representatives are available
via email at [email protected].
5
Parts Identification
Front View
Back View
6
Internal Fan
This is an air-cooled unit equipped with an internal fan that maintains a consistent internal
temperature.
Tip: Gather the model and serial number from the product label and write them down before
installing the Wine Refrigerator.
7
Warning: Use two or more people to move and install the wine refrigerator. Failure to do so
can result in back or other injury. Carefully remove the packaging materials. Remove any
shipping tape and glue from your wine refrigerator before use. Do not use sharp instruments,
rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your wine refrigerator.
Important: Do not remove any safety, warning, or product information labels from your wine
refrigerator.
Installing the Wine Refrigerator
The wine refrigerator should be installed in accordance with local electrical code requirements.
The wine refrigerator should also be placed in a location that is strong enough to support its
total weight, keeping in mind that it will weigh substantially more when fully loaded than when
empty. Before you plug the wine refrigerator into a power supply, be sure to let it stand
upright for at least 24 hours to allow the compressors oils to settle.
Unpacking the Wine Refrigerator
Installation
This wine refrigerator has been designed for free-standing installation. There must be
adequate ventilation and access for service.
Free-standing Installation:
A free-standing installation will allow you to install the wine refrigerator in almost any place
you desire as long as there is proper ventilation. This product is not designed to be built
into a cabinet or recessed setting. You must follow the stated instructions for electrical
requirements, and leveling the wine refrigerator.
Choose a location that has ambient temperatures above 50° F and below 95° F.
Operation outside these temperatures may lead to lowered efficiency or other adverse
effects.
This unit MUST be installed in an area protected from the elements, e.g., wind, rain,
water spray or drips.
The wine refrigerator should not be located next to ovens, grills, or other high heat
sources.
Do not kink or pinch the power supply cord between the wine refrigerator and the wall
or cabinet.
The wine refrigerator should be installed on a firm and level surface that will be able
to support the entire weight of a fully loaded unit. It is important for the wine
refrigerator to be level in order to work properly. If needed, you can adjust the height
of the wine refrigerator by rotating the feet. See the “Leveling the Wine Refrigerator”
section.
A standard electrical supply (115 VAC only, 60 Hz), properly grounded in accordance
with National Electrical Code and local codes and ordinances, is required.
Warning: DO NOT install the wine refrigerator behind a closed cabinet door.
8
Installation Clearance Requirements
To ensure proper ventilation and service access, allow at least 3” of clearance at the sides
and top of the wine refrigerator, and at least 5” of clearance at the back. Do not install this
unit in a built-in undercounter setting.
9
ELECTRIC SHOCK HAZARD!
Plug into a grounded 3-prong outlet.
Never remove the grounding prong from the plug.
Never use an adapter to bypass the grounding prong.
DO NOT use an extension cord.
Failure to follow these instructions can result in fire, electrical shock, or death.
Important: Once you are ready to install the unit in a cabinet or directly on the floor, you must
adjust the feet to level the Wine Refrigerator.
Electrical Requirements
Before you move your Wine Refrigerator into its final location, it is important to make sure you
have the proper electrical connection:
A standard electrical supply (115 V, 60Hz), properly grounded in accordance with the National
Electrical Code and local codes and ordinances, is required.
It is recommended that a separate circuit, serving only your Wine Refrigerator, be provided. Use
receptacles that cannot be turned off by a switch or pull chain.
The fuse (or circuit breaker) size should be 15 Amps.
Recommended Grounding Method
For your personal safety, this appliance must be grounded. It is equipped with a power
supply cord that has a 3-pronged grounding plug. To minimize possible shock hazard, the
cord must be plugged into a mating 3-pronged wall socket, and grounded in accordance
with the National Electrical Code and local codes and ordinances. If a mating wall socket is
not available, it is the personal responsibility of the customer to have a properly grounded,
3-prong wall receptacle installed by a qualified electrician.
Leveling the Wine Refrigerator
It is important for the Wine Refrigerator to be level in order to work
properly. It can be raised or lowered by rotating the plastic sheaths
around each of the feet on the bottom of the machine. If you find that
the surface is not level, rotate the feet until the Wine Refrigerator
becomes level .You may need to make several adjustments to level it.
We recommend using a carpenter’s level to check the machine.
1. Place a carpenter’s level on top of the product to see if the Wine
Refrigerator is level from front to back and side to side.
2. Adjust the height of the feet as follows:
Turn the leveling feet to the right to lower that side of the
refrigerator.
Turn the leveling feet to the left to raise that side of the
refrigerator.
10
Installing the Door Handle
To install the door handle:
1. Open the door and carefully pull the door gasket around the area where the handle is to
be installed.
2. Carefully remove the two pre-installed decorative plugs from the front of the door.
3. Insert each Phillips head screw through the gasket side of the door until the screw passes
through the door.
4. Align the handle with the screws and tighten using a Phillips head screwdriver until the
handle is flush against the door frame.
5. Carefully press the door gasket into its original position.
Installing and Removing the Shelves
To prevent damaging a door gasket, make sure to open the door all the way before pulling the
shelves out of their track.
To Install the Shelves:
1. Open the door completely.
2. Note the location of the protective stoppers on the right and left side of the back of
each shelf.
3. Lift either side of the shelf to create a 45° angle.
4. Insert the shelf at the desired shelf slot and push back slowly until it stops in place.
5. Gently lower the shelf down into place.
To Remove the Shelves
1. Open the door completely.
2. Make sure the shelf is pushed in completely towards the back of the Wine Refrigerator.
3. If necessary, make sure you remove all the contents sitting on the shelf.
4. Lift either side of the shelf to create a 45° angle and raise the shelf slightly to avoid
the shelf mounts on the inside of the cabinet.
5. Pull the shelf straight out until it is completely removed. Set aside gently.
Note: some wine refrigerators do not have decorative plugs installed.
Caution: Do not over-tighten the screws as this may cause damage to the handle or to the
stainless steel door.
11
Reversing the Door Swing
Follow the instructions below to reverse the door swing.
To Reverse the Door from Right Swing to Left Swing
1. Open the door and using a Phillips screwdriver, remove the bottom screws from the
lower hinge.
2. Carefully slide the bottom of the door forward and down, and place it on a padded
surface to prevent damage.
3. Remove the decorative plastic cap from the top left corner of the door and insert it onto the
right top corner. Do not attempt to pry up on the metal ring mounted on the door. The cap is
inside of this ring.
Important: Before you begin, unplug the refrigerator.
12
4. Remove the front leveling leg from the right bottom corner of the cabinet and then
remove the three screws that are used to hold the lower hinge to the glass door.
5. Remove the front leveling leg from the left bottom corner of the cabinet, then install
the leveling leg into the right bottom corner of the cabinet and tighten it.
6. Install the lower hinge by fastening the screws through the lower hinge to the cabinet.
Install the front leveling leg.
7. Remove the screws from the upper right hinge. Place the upper right hinge in a safe
place in case you need to reverse the door in the future. Remove the plastic caps
from the upper left hinge corner. Install the upper left hinge by fastening the screws
through the left hinge to the cabinet.
13
8. Install the support bracket and bushing on the lower hinge.
9. Carefully insert the door into the upper right corner hinge, then slide the door on top
of the lower hinge and secure the door by installing the lower screws.
Removing and Installing Decorative Plugs
Follow the instructions below to remove the decorative plugs from the door.
1. Open the door and carefully pull the door gasket from the top left corner until you have
exposed the two holes which correspond with the decorative plugs.
2. Insert a Flathead screwdriver through the gasket side of the door into the decorative plug
slot. You may need to use a flashlight to help guide you through this process.
Important: Before you begin, unplug the refrigerator.
14
3. Carefully turn the screwdriver clockwise to remove the two pre-installed decorative plugs
from the front of the door. Reinsert the decorative plugs into the right side of the door
using this same procedure.
4. Remove the decorative plastic cap from the top left corner of the door and insert it
into the top right corner. Do not attempt to pry up on the metal ring mounted on the
door. The cap is inside of this ring.
5. After the cap is inserted, carefully press the door gasket into its original position.
Operation
Installation Check List Before Operation
1. Have all packing materials and tape been removed from the interior and exterior of the
Wine Refrigerator?
2. Have the installation instructions been followed, including connecting the machine to
electricity? And has proper grounding been installed for the Wine Refrigerator?
3. Has the machine been leveled?
4. Is the Wine Refrigerator in a site where the ambient temperature is between 50° F and
95° F all year round?
5. Is there a clearance of at least 1- 2” at the rear, 1/4” at the top, and 1/4” at the sides for
proper air circulation?
15
Using the Temperature Control Panel
The dual zone wine refrigerator has a temperature range from 40°F to 65°F for the upper and lower zone.
Power Button : Turns the unit on and off. ( press and hold this button for approximately
3 seconds).
Button : Energy conservation button. Pressing this button for 3 seconds will turn the
energy conservation mode ON or OFF. In this mode, all LED lights and electronic displays will
turn off.
Up Button : Press the button on the control panel to increase the temperature by 1
degree increments.
Down Button : Press the button on the control panel to lower the temperature by 1
degree increments.
RUN LIGHT: When lit, the unit is in cooling mode
Light Button : Press the button to turn the inner light on or off.
Button :To switch between C and F. press the buttons for approximately 3 seconds.
A beep will occur and the indicator light will illuminate next to desired temperature setting.
Note:
The Wine Refrigerator is equipped with a temperature memory function. If power is
suddenly lost, the previously set temperature will be saved and the refrigerator will return to
this setting once power is restored.
Allow at least 24 hours before storing your wines to allow the setting temperature to be
reached.
Caution: If you powered the unit off, please wait at least 5 minutes before powering it back on.
16
Warning: Never attempt to remove frost with a sharp object!
Normal Sounds
Your new Wine Refrigerator may make sounds that are not familiar to you. Most of the new
sounds are normal. Hard surfaces like the floor and walls can make the sounds seem louder
than they actually are. The following describes the kinds of sounds that might be new to you
and what may be making them.
Rattling noises may come from the flow of the refrigerant or the water line. Items stored on
top of the Wine Refrigerator can also make noises.
The high efficiency compressor may make a pulsating or high-pitched sound.
Water running from the evaporator to the water bin may make a splashing sound.
As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your
Wine Refrigerator.
Temperature Alarm
If the interior temperature is higher than 73°F (23°C), “HI” is shown on the temperature
control panel and the temperature alarm will sound continuously after one hour.
This indicates that the inner temperature is too high. If the inner temperature is lower
than 32°F (0°C), “LO” is shown on the temperature display panel and the temperature
alarm will sound continuously after one hour. If one of these situations occurs please
reference the troubleshooting section found in this manual or contact EdgeStar for support.
Door Ajar Alarm
This Wine Refrigerator includes a door ajar alarm, which will sound if one of the doors is
open for more than five (5) minutes. Leaving the door open for extended periods of time
will cause poor cooling performance and may shorten the life of the refrigerator. Keep
the doors closed as frequently as possible.
Defrosting
Note that under most refrigerating settings, the unit will automatically defrost under most
ambient conditions. However, on colder settings, some frost may build up. Additionally, the
more humid the ambient conditions, the more frost may build up. Keep the door closed as
much as possible and avoid opening the door unnecessarily to minimize frost build-up.
If frost is preventing the door from closing properly, you may need to power the unit off until the
frost melts. Use a soft absorbent towel to dry the unit.
Preparing the Wine Refrigerator for Storage
If the Wine Refrigerator will not be used for a long time, or is to be moved to another place, it
will be necessary to defrost the unit and dry the interior.
1. Disconnect the wine refrigerator from the power supply by removing the power plug from
the wall socket.
2. Leave the door open to allow for air circulation and to prevent mold, mildew, and
unpleasant smells.
17
Cleaning and Maintenance
Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life.
Exterior Cleaning
The door and cabinet may be cleaned with a mild detergent and lukewarm water solution such
as 2 tablespoons of baking soda to 1 quart of water.
Do not use solvent based or abrasive cleaners. Use a soft sponge and rinse with clean water.
Wipe with a soft clean towel to prevent water spotting. If the door panel is stainless steel, it can
discolor when exposed to chlorine gas and moisture. Clean stainless steel using a cloth
dampened with a mild detergent and warm water solution. Never use an abrasive or caustic
cleaning agent.
Interior Cleaning
The Wine Refrigerator’s interior should be cleaned occasionally.
1. Disconnect power to the unit.
2. Open the door and remove the contents and shelves.
3. Wait until the unit defrosts.
4. With a clean cloth, wipe down the interior of the unit.
5. Reinsert the shelves and wine.
6. Reconnect power to the unit.
18
Troubleshooting
Before Calling for Help
If the unit appears to be malfunctioning, read through the “Operation” section of this manual
first. If the problem persists, check the Troubleshooting Guide below and on the following page.
The problem may be something that can easily be solved or explained.
Symptoms
Possible Causes
Solutions
The wine refrigerator turns on
and off frequently.
The room temperature is
higher than the recommended
ambient environment.
Run the refrigerator at the
appropriate ambient
temperature.
The door is being opened too
often.
Minimize the number of times
the door is opened.
The door is not completely
closed.
Make sure the door is
completely closed.
The door gasket is not sealing
properly.
Make sure the door gasket is
sealing properly.
The refrigerator does not
have the suggested
ventilation.
Read and follow the
“Installation Clearance
Requirements” section.
The wine refrigerator does not
turn on.
There is a power failure.
Ensure that the refrigerator is
plugged in and the power
outlet has power.
The refrigerator is not plugged
in.
Plug the unit in to a power
outlet that has sufficient
amperage.
A house fuse has blown or
the circuit breaker is tripped.
Replace the broken fuse in
your fuse box or reset the
breaker.
The wine refrigerator will not
reach the desired
temperature.
The refrigerator is placed too
close to a heat source.
Keep the refrigerator away
from direct sunlight or other
heat sources.
The refrigerator does not
have sufficient ventilation.
Read and follow the
“Installation Clearance
Requirements” section.
The door is opened too
frequently or for a long period
of time.
Close the door tightly and do
not open the door too
frequently or for a long period
of time.
The wine refrigerator is
making strange noises.
Certain sounds are normal.
Read the “Normal Sounds”
section.
The unit is not level or is
touching another appliance.
Check to make sure that the
refrigerator is level, and that it
is not in contact with another
appliance or furniture.
19
Symptoms
Possible Causes
Solutions
The body of the Wine
Refrigerator is electrified.
The unit is not grounded
properly.
Contact your local electrician
to test your electrical
grounding system.
Frost is forming in the wine
refrigerator.
The environment is humid.
Though the unit uses an
“auto-defrost” system, under
certain conditions, manual
defrosting may be required. If
frost builds up, you can try
running the refrigerator on a
warmer temperature setting,
minimizing the number of
times you open the door, or
unplugging the unit to allow
the frost to melt.
The ambient temperature is
too low.
The door is being opened too
frequently.
The door will not shut
properly.
The refrigerator is not level.
Make sure the refrigerator is
on a level surface.
The door gasket is dirty.
Clean the door gasket.
The door gasket is not
installed correctly.
Make sure the door gasket is
correctly installed.
The shelves are incorrectly
installed.
Install the shelves correctly.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

EdgeStar CWF380DZ User manual

Category
Wine coolers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI